Search Documents

By Gennaro G. Marino

As part of the development of a shopping center in West Virginia, a significant bench had to be cut into a mountainside that was over 700 ft. high. As a result, a steeply stepped, over 400-ft.- high wall was created. The high wall exposed old abandoned room-and-pillar coal workings at the toe of the cut. Because of exposure to the elements, the mine openings began to severely deteriorate with significant potential of undermining of the rock cut face and causing a large rock fall(s). Exacerbating this wall problem was a set of fairly planar sub-parallel and sub-vertical joints creating, in essence, thin rock slabs. Also present were stress relief fractures that were observed in the exposed pillars. Given the proximity of the project building to this high rock face, mitigation of the rock fall potential was deemed necessary. In order to prevent continued damage and deterioration of these exposed mine entries, the rubblized openings were filled with bulkhead grout and pressure injected with grout. The total amount of grout installed in these openings was about 3,945 CY. Also, a rock drape was attached to the entire face to mitigate small rock falls from natural causes. There also existed another level of mining below the ground surface and under an existing building at a depth of about 160 ft. Under a portion of the building, the pillars in these old works were second mined, and the building seemed to have been already affected by limited subsidence above this area. Also, calculated pillar safety factors in this high extraction section of the mine were too low. Consequently, these old works were stabilized by saturation grouting. An indication of overall roof distress was the significant fracturing encountered in the bedrock overburden during the drilling of the injection holes and the volume of grout placed in these holes. The total grout installed in the high extraction section of the lower mine was about 6,660 CY. This paper describes the investigation and the grouting techniques employed at the rock cut face and under the existing building to mitigate continued damage to avoid future subsidence problems at the face and the building premises.

Jan 1, 2013

By P. Tittes, M. Deal, M. Spicher, S. McDaniel, J. Wickens

"Haile Gold Mine is located near Kershaw, South Carolina, approximately 50 miles south of Charlotte, North Carolina. Gold was first discovered at the site in 1827, and the property has been through several operating periods since. The relatively low grade and refractory nature of the deposit has been a challenge for efficient processing since the start of mining on the property. Early processing techniques included gravity separation and barrel chlorination. The last operation employed heap leaching in 1985 through 1992. After being closed and reclaimed for over 20 years, the property is poised to re-open and produce once again. In this chapter of the Mine’s legacy, flotation and ultra-fine grinding will be employed to achieve economic extraction of gold and silver from the pyrite. This paper briefly reviews some of the mine’s history, the metallurgical testing, the flowsheet and discusses design considerations.INTRODUCTIONHaile Gold Mine is located near Kershaw, South Carolina, approximately 50 miles south of Charlotte, North Carolina. Gold was first discovered at the site in 1827, and the property has been through several operating periods since. The last operation employed heap leaching in 1985 through 1992. Since then, the property has been closed and fully reclaimed. Romarco Minerals acquired the property in 2007, and began an exploration program that has delineated over 62 tonnes (+2M ozs.) of gold in reserve at an overall grade of 2 ppm (0.06 opt). This paper provides a brief history of the property, a summary of metallurgical testing, description of the process flowsheet and discusses design considerations.HISTORY1827 – 1837Gold was discovered in creek beds on the Haile property in 1827. The property was owned by Benjamin Haile, and the first few years of production came from placer mining. After gold was discovered in schist beds to the sides of the streams, Haile expanded the operation by leasing 18 meter-square (50 ft.) plots to local planters. These planters used slaves to work the small excavations in the agricultural offseason. The gold ore was taken to arrastras where the free gold was liberated and recovered. The excavations were above the water table, generally less than 18 meters (60 ft.) down, and it was noted then that gold could be found embedded in sulfides and difficult to extract."

Jan 1, 2013

By Adrian Moore, Alan Richards

"It has been common practice to set blast vibration limits for structures using an “observational”approach whereby limits are set at a level based on observations of damage, or the lack ofdamage, combined with a tendency to further reduce the permitted level due to uncertainty. Suchan observational approach was used in the USBM RI 8507 to produce the frequency dependent‘Safe Levels of Blasting Vibration for Houses’ which has become a universal Standard for overthirty years."

Jan 1, 2013

ABSTRACT Inco’s Iron Ore Recovery Plant was operated by Inco from 1955 to 1980 near Sudbury, Ontario. As exposures to specific nickel substances have been associated with adverse respiratory endpoints it is important to understand processes giving rise to such substances. This manuscript discusses the process and equipment, the propensity for aerosol formation, and operational procedures used by Inco in roasting a pyrrhotite concentrate, reducing the nickel in the formed oxide, leaching the nickel in ammoniacal solution, purifying the resulting solution, making green or black NiO, and producing iron oxide pellets. Industrial hygiene measurements are also reported.

Jan 1, 2013

By Anthony T. Iannacchione

This study, funded by the Appalachian Research Initiative for Environmental Science (ARIES), examines how mine layout, mining method, and geology interacted to allow water from the Grove No.1 mine pool to discharge into local surface waters. Federal and State regulations prohibit the discharge of acid or iron-producing waters from underground coal mines. Mining companies design barriers around their operations to prevent mine waters from discharging to the surface. The Grove No.1 represents one mine where these designs proved inadequate. Unique geologic conditions at the Grove No.1 mine pool, combined with retreat room-and-pillar mining, contributed to a discharge that required passive water treatment.

Jan 1, 2013

By Yuanming Pan, Brett Rogers, Baoquan Hu, Gary Yeo, Christine Austman

The nature and distribution of radiation-induced defects (RIDs) in quartz from the Maw Zone, a yttrium- and rare-earth-element-enriched sandstone breccia complex exhibiting intense hydrothermal alteration, have been investigated by electron paramagnetic resonance (EPR) spectroscopy. EPR spectra show that detrital quartz in sandstone, from five diamond drill holes intersecting the Maw Zone and one above the crest of the so-called Quartzite Ridge, contain only background-level RIDs, indicating that Ubearing fluids were absent in this area. However, close to the sandstone-basement unconformity, in hole WR-194 immediately west of the Quartzite Ridge, the concentration of RIDs in detrital quartz is significantly above background but at least an order of magnitude lower than those at the Key Lake and McArthur River deposits. Widespread drusy quartz at the Maw Zone, which signifies intense hydrothermal alteration, is associated with hematite-, sulfide- and carbonate-bearing mineral assemblages, which exhibit complex crosscutting relationships. EPR spectra of drusy quartz in all three types of mineral assemblages are low in RIDs as well, supporting the EPR evidence that fluids at the Maw Zone did not carry significant U. These EPR results suggest that, in spite of intense hydrothermal alteration and favorable structural geology, the Maw Zone is unlikely to host any significant U mineralization. Moreover, this study shows that the EPR technique is potentially a useful exploration tool, capable of determining whether individual alteration zones in the Athabasca Basin were associated with U-bearing fluids or not.

Jan 1, 2013

By Takashi Saito

Since early 1970?s skirt suction foundations (skirted foundation / bucket foundation) have been used as support for large fixed substructures or anchors for floating structures in offshore hydrocarbon development projects. In recent years skirt suction foundations are recognized as one of the solutions in foundations applicable to bridge substructures installed in waters, because skirt foundations have a wide variety of functions such as control of settlement during service life, less impact to environments during operation at installation site. This paper introduces general features of skirt suction foundations, and then discusses design practice of them for the application to bridge substructures, with reference to experiments in both laboratory and field.

Jan 1, 2013

By Douglas A. Anderson

Much progress has been made in understanding the forward process for blast vibration simulation: that is, how to create a resultant seismogram from an empirically determined seed waveform. What has not been successfully investigated to date is the reverse process: Determining the contribution of each borehole to the resultant seismogram. It might seem that these should be two sides of the same coin, but the reverse process is much more complicated. That is because the source, geological path, and receiver contributions must be unraveled and then dissected. If that can be done, a relationship can be developed between the seismic source properties and the explosive interaction with the surrounding rock. This paper presents a first step in the unraveling process, through analysis of blast seismograms using wavelet transforms.

Jan 1, 2013

By Takashi Sasaoka

A great deal of coal will be left under the final end-walls in Chinese surface coal mines because of lower slope angle in shoveltruck mining systems and larger mining depths. In traditional surface mining systems, the coal under the end-walls will be buried by the inner dumping site, and these coal resources are generally abandoned. Considering these situations, the application of end-wall mining systems was considered in order to recover the residual coal around the end-wall. This mining system can improve economic benefits by exploiting haulage and ventilation roadways from end-walls and utilizing the existing transportation systems. In order to develop the appropriate pillar design methodology for the end-wall mining system, several empirical formulas and methods were discussed based on the formulas developed so far and the mechanics properties of coal and rocks in the Chinese coal mine. From the results of a series of theoretical and numerical analyses, it can be concluded that the coal pillar width calculated by the Mark- Bieniawski formula may serve as an important reference for pillar design in end-wall mining systems, and the end-wall mining system can increase the coal recovery from residual coal resources around highwall and reduce the effect of underground mining operation on slope stability

Jan 1, 2013

By K. Lascelles

ABSTRACT Nickel compounds vary significantly in their toxicological properties, so it is critical that continuing studies to accurately quantify worker exposures consider the processing that accompanies refining nickel-containing materials. The Clydach nickel refinery, which has operated for more than 100 years, was the first nickel-producing facility to show a high risk for lung and nasal-sinus cancers among workers employed since it opened in 1902. Process chemistry and equipment have changed dramatically over Clydach’s history. This paper describes the processing evolution at Clydach with a focus on the propensity for aerosol formation and the forms of nickel in airborne dusts.

Jan 1, 2013

By Kyle A. Perry

Pillar design formulae have existed for decades, and the guidelines for design stability factors are generally accepted by regulatory agencies and broadly used within the coal industry. Nearly all design pillar formulae are based on geometrical parameters of pillars resulting from empirical investigations, with primary focus on the pillar width-to-height (W/H) ratio and associated shaping constants from regression. The most widely used modern pillar design formula in the coal industry, the Mark- Bieniawski equation, also adheres to this principle. Common practice when applying Mark-Bieniawski equation is to use a coal compressive strength of 900 psi. This reduces the design equation to sole dependence upon geometry. However, recent studies have shown that pillar strength is highly dependent on roof and floor properties, particularly the interfaces between the roof-pillar and pillar-floor. This study utilized numerical modeling using FLAC3D to evaluate the relative effects of varying roof and floor interface and mechanical properties. The results confirm that pillar strength is significantly influenced by the properties of the coal pillar interfaces with roof and floor. The mechanical properties of the roof and floor material have only a minor impact on pillar strength when compared with interface effects. These results were used to formulate design recommendations for existing pillar design methods.

Jan 1, 2013

By D. Yuan, L. Yan, M. J. Collins, P. Kalanchey, I. M. Masters

ABSTRACT Pressure oxidation tests have been conducted by Sherritt for a refractory gold-silver project in China. The feed contained 39 g/t Au and 970 g/t Ag; the major gold-bearing minerals were pyrite and arsenopyrite. Because the feed contained a significant amount of silver, which can be refractory to cyanide leaching after pressure oxidation due to the formation of argentojarosite, the test program included investigation of methods to enhance silver recovery. The “lime boil” process proved successful and was incorporated into the flowsheet. Gold extraction from the lime boil product solids was 95–98%; silver extraction was up to 94%.

Jan 1, 2013

By Liang Shen

The Cooper River Bridge, the longest cable-stayed bridge in North America, replaces two existing bridges along U.S. Highway 17 and connects the City of Charleston and the town of Mount Pleasant, South Carolina. Two diamond shaped towers support the 1,546 ft long main span over Cooper River and allows for a 1000 ft wide navigation channel. The Charleston high-level approach is 4351 ft long and provides a 250 ft wide navigation channel for Town Creek, while the Mount Pleasant high-level approach is 2,090 ft long. Due to the high seismicity in the region, potential vessel impact, and hurricanes, large lateral loads are expected. From various types of foundations, 10-foot diameter drilled shafts were selected for their high capacity against vertical and lateral loadings. The shafts are founded on a stiff to very stiff lightly cemented calcareous sandy clay or sandy silt layer, called Cooper Marl, which underlies the coastal sediments of the interbedded clays and sands. A group of 11 shafts supports each main tower, while a rock island protects it from vessel collision. A group of 4 to 8 shafts foundations support the other piers of the main span unit. A pair of shafts supports the High Level Approach piers. The shaft tip elevations vary from 120 ft to 230 ft below water line. An elaborate geotechnical investigation was conducted on the site, including a load test program on full-scale shafts under axial and lateral loads. The results of the tests were used to calibrate the lateral and axial soil resistance. The objective of this paper is to present the different aspects of the bridge foundation design.

Jan 1, 2013

By C. Fortin

ABSTRACT The subject of gold flotation has been reviewed extensively. Most of these reviews focus on the theories of gold flotation and the physical and chemical effects that may impact the efficacy of the gold flotation process. The current status of gold flotation chemistry as it is being applied in industry has not been widely addressed. This paper reviews current gold flotation practice and research advancements and discusses how these applications tie in with the current understanding of gold flotation chemistry. Survey results from worldwide gold flotation operations are analyzed. Potential future areas of gold flotation research are highlighted.

Jan 1, 2013

By Enrique Munaretti, Cathy Aimone-Martin, Vitor Rosenhaim, Jair Koppe

Production blasts at one of Copelmi’s coal mine operations will be carried out 100 m (330 ft) from a neighborhood located in the town of Butiá, southern Brazil. Mine management is concerned about the possibility of damages and complaints due to blasting operations at close distances to structures of substandard construction. Blasting in the area is characterized by the use of very low powder factor resulting in confined shots in which movement is restricted to a point of almost undershooting the rock. Over the past year, tests were conducted mainly in the overburden area to determine the best approach to be implemented when blasts move closer to the town. Mine management wants vibration levels to be reduced lower than the damage limits proposed by Brazilian regulations to ensure a safety margin and mitigate perception by the community hoping to reduce the number of complaints.

Jan 1, 2013

By Charles S. Spirakis

The consistent occurrence of organic carbon early in the paragenesis of Mississippi Valley-type sulfide deposits suggests a genetic link between organic carbon and the sulfide ores. Reduction of sulfate in the mineralizing solution by organic carbon at the sites of mineralization is commonly proposed as the precipitation mechanism for these deposits, but inorganic sulfate reduction is too slow to be important to the chemistry of the ore zone, and bacteria, which catalyze sulfate reduction at low temperatures, are not known to survive at the temperatures of mineralization. Sulfate reduction with or without bacteria is not consistent with the sulfur Isotope evidence. Sulfur isotope studies also indicate that the derivation of sulfur from hydrocarbon at the sites of mineralization is unlikely. Organometallic complexing may be involved in the transport of metals, but no plausible mechanism for breaking these complexes at the sites of mineralization has been proposed. Reduction of partly oxidized sulfur species in the mineralizing solution by organic carbon at the sites of mineralization is a possibility which deserves further scrutiny.

Jan 1, 2013

By Ronald C. Severson

Crystals of native gold occur in placer-type deposits. Gold, as a pure metal, is the most malleable metal known; therefore, delicate gold crystal forms should not survive mechanical transport and concentration processes involved in placer formation. To test the hypothesis that the crystalline gold is currently forming in place, two active gold-placer operations and an unmineralized background area in Alaska were examined. At these sites, rock outcrops, soil profiles, and native vegetation were sampled. At one sampling site, the soil was panned and yielded crystalline gold, as well as the more common rounded nuggets. The plants and soils were analyzed for their major, minor, and trace-element contents, especially gold. Two procedures, one a simple demineralized water leach and the other a partial digestion with acetic acid and hydrogen peroxide, were also used to extract gold and various anions from soils. The water-extractable gold ranged from <0.02 to 15.0 ppb Au in the extracting solution. This represents as much as a 104 enrichment in gold over average river water. This extractable gold is probably available to the native vegetation. Gold concentrations in the unashed dry plants from the two placer sites ranged between 0.4 and 106 ppb compared to a background range of <1 to <4 ppb Au. The presence of dissolved organic matter in the soils is thought to be responsible for the dissolution, transportation, and precipitation of gold in these placer soils, and this process is presently active in these soil profiles.

Jan 1, 2013

By Kimberlee Falkenstein, Volha Kibitkina, Jessica Steeves

A series of experiments were conducted to obtain site specific constants for the vibration produced by a single charge and by more charges detonating in sequence, using short delay intervals. All charges were placed in relatively long boreholes in granite without a free face other than the ground surface. The boreholes were filled with water to provide good coupling with the rock and to provide identical confinement for all the blasts. Vibrations were recorded close to each blast in the vertical direction by uniaxial high frequency geophones and far field using a triaxial geophone.

Jan 1, 2013

By Braden Lusk

Vibrations as a result of blasting practices in mining engineering are a complex phenomenon controlled by many variables. Mine blast vibration modeling and prediction is becoming more important as a consequence of interactions by mining activity with an ever closer public. Many communities (all over the world) close to mining activity often complain about airblast and vibrations produced from blasting activity. It is important for the mining industry to have tools and understandable methodologies to model and predict blast vibration. These tools can then be used to predict and control vibration at neighboring structures.

Jan 1, 2013

By Mauritz Kotze, Jason Furtney, Ewan Sellers, Sandy Etchells, Tom Szendrei

The development of a simple model for gas flow and burden movement has driven the need to improve our understanding of burden breakage mechanisms for single hole blasts and the interaction between multiple holes in solid and jointed rock masses. Conventional analytical understandings of the burden breakout using the elastic-tensile fracture model were studied and found to provide a breakout angle that is independent of burden in contradiction to experimental data. By considering rock fracture in terms of Mohr-Coulomb plasticity using analytical expressions from the field of cavity expansion analysis an improved relationship between breakout angle and burden is derived until the point of critical breakout at which the angle of breakout suddenly changes from between 90 degree and 100 degrees to zero. This suggests that the critical burden occurs at about 0.6 times the radial fracture zone calculated from the analytical solutions.

Jan 1, 2013