Search Documents

By Y. Guglielmi, C. Gout, P. Henry, P. Dick

The key questions about fault reactivation in shales concern the potential enhanced fluid displacement through a previously low-permeability aseismic shale formation. Here we selected a critically-stressed fault cross-cutting the underground research facility of Tournemire (France) which is located in Toarcian shales. Several inclined boreholes were drilled across the 8.5 m thick fault zone characterized by a fractured damage zone (FDZ) and a central 2.4 m thick complex core (FC) made of multiple shear bands with gouge intercalated with highly fractured lenses. The fault was pressurized using a straddle packer system defining a 2.4m long injection chamber normal to the fault surface. Three fault zone intervals were tested, two in the fault damage zone and one in the fault core. A three-dimensional displacement sensor set in the chamber allowed continuous synchronous coupled monitoring of fault movements, injection pressure and flow rate. An anticlockwise 0.22-to-0.05 mm fault slip was captured associated with a 10-to-100 hydraulic aperture increase of the fault. Preliminary analyses of the experiments show that leakage in the fault zone is controlled by strength and stress magnitude contrasts between the fault core and the fault damage zone. Fault damage zone discontinuities display a much higher peak static friction angle than the fault core shear zones, respectively of 34 and 22° that could be related to complex interactions between healing and sealing processes. Fault core leakage is much more dependent on strain than on effective stress variations. Discontinuous, pulse-like leakage, develops following complex failure processes that may simultaneously take place in the gouge zones and along the large pre-existing discontinuities. Such results may be of importance in evaluating fault seal integrity in oil and gas exploration, production or CO2 storage or underground excavations monitoring.

Jan 1, 2015

By J. Arzúa, L. R. Alejano, P. Rodríguez

"After six years of successful excavation with a support pattern, some roof failures have happened in a room-and-pillar underground mine excavated in a stratified rock mass. In this paper the authors give explanation to the failure mechanisms and redesign the support in order to solve the recent problems of roof collapse.The mine magnesite bed is approximately 14 m thick, and runs in the E-W direction with an average dip of 18º. Due to mine constraints and the inexpensiveness of the ore, the excavation is performed in the mineral itself, avoiding the need for mining dumps and waste excavation. Rooms and drifts are oriented in the mineral bed to form an angle of 19º to the direction of the strata, reducing the roadway gradients to less than 10%. Rooms are 11 m wide and pillars are 7 m wide. They are designed to leave a 1 meter thick magnesite bed in the roof of the rooms to act as a supporting beam. More often than not there is a layer of very poor quality marly shale up to 1 m thick resting on this magnesite beam. Overlying the poor quality marly shale there is a better quality, self-supporting sandy shale.First, a characterization of the involved rock masses (magnesite, marly shale and sandy shale) is performed, collecting the geotechnical data from previous studies and performing new in situ geotechnical surveys to check the soundness of the previous data. A distinction is made between different quality zones inside the mine by means of the RMR classification, associated to the occurrence of faults.Back-analysis of some of the failed rooms and data from exploration boreholes were used to determine the failure mechanisms (associated to Voussoir type failure or occurrence of sub-horizontal joints crossing the magnesite beam). Based on an understanding of these mechanisms, the method used to design the support and to analyse the stability of the different possible thicknesses of the magnesite beams of the rooms and drifts of the mine were improved.Numerical models of the most relevant conditions found in the mine were performed in order to better understand the behaviour of the roofs and to simulate the supporting solution obtained in the previous analyses.The most relevant conclusions with regard to the main elements causing the instability of the roof include the appearance of sub-horizontal discontinuities crossing the magnesite bed, which causes total instability of the roof and usually leads to collapse; excessive thinness of the magnesite beam in the problematic rooms; and the relaxation of the deepest (around 270 m in depth) zone of the mine because of existing faults."

Jan 1, 2015

By S. Gheibi, H. S. B. Duzgun, N. Dadashzadeh

It is widely recognized that there are various uncertainties in the analysis of rock slope stability owing to inadequate information for site characterization and inherent variability and measurement errors in geological and corresponding parameters. Therefore, reliability-based approaches that allow the systematic and quantitative treatment of these uncertainties have become a topic of increasing interest in rock slope engineering. There has been extensive reliability analysis of rock slope stability in the literature. However, all of these analyses are based on the First-Order Reliability Method (FORM). The probability of failure of a rock slope in the First-Order Reliability Method is provided by a linear approximation of the failure function. The FORM is most commonly used because it is efficient; its accuracy, however, deteriorates when the nonlinearity of limit-state function increases. A better approximation of the failure function can establish a more accurate value of the probability of failure. The Second-Order Reliability Method (SORM) overcomes this drawback with a cost of lower efficiency in terms of the number of function calls and computation expenses. Despite considerable studies of the application of the SORM in other engineering fields, a few attempts have been made in the slope stability studies. In this study, a recently published Second-Order Reliability Method with First-Order Efficiency (SORM-FOE) is implemented on a selected rock slope in Amasya, Turkey. The SORM-FOE overcomes the low efficiency of the SORM by decreasing the number of function calls. The probability of failure of both FORM and SORM-FOE are obtained and the results are compared. It is shown that, in high value of failure probability, SORM’s do not significantly affect the analysis and design. However, in very low failure probability, the discrepancy between FORM and SORM-FOE becomes pronounced. It is also shown that, where the second order methods are required, the SORM-FOE is more efficient than the conventional curvature fitting methods in terms of computational costs.

Jan 1, 2015

By Pedro Pablo Vasquez Coronado, Victor Octavio Tenorio

"Productivity in openpit mines depends on the observation and adjustment of critical phases of operation. As one of the most expensive activities in openpit production, optimization of the load-haul-dump cycle becomes a critical aspect to address. Using simulation techniques and an ad hoc methodology for analyzing the key performance indicators (KPIs) involved in the production cycle, it is possible to compare actual performance and ideal operating conditions and develop an alert system when operating conditions are subpar with the expected production standards.Study objectivesThe purpose of this work is to implement a methodology for optimizing the haulage cycle by identifying and adjusting the factors that affect the cycle time performance. The methodology includes the implementation of an alert system emitting warning messages when one or several trucks are idle, or when the time of completing production tasks is falling outside a predefined value. This alert is compared with predefined KPIs and is used to determine corrective actions.The alert will:• Demonstrate the benefits of time analysis and how this affects the productivity results in the mining process.• Demonstrate the utility of KPIs in the extraction of ore and waste and how they help to identify equipment performance.• Develop software interfaces to visualize the alert system in order to increase awareness in the operations supervisor.• Make recommendations for future applications that can help improve the productive process of an openpit mine.Problem statementTransporting material in openpit mines may require the utilization of high capacity equipment, which also represents an elevated cost per hour. A supervisory system that controls the adequate distribution of trucks and shovels by providing the operational status of each unit shall contribute to increase productivity while subsequently reducing operational costs. Nevertheless, there is an issue with certain dead times such as queue trucks for loading, trucks waiting to be loaded and other delays. This creates inefficiencies in fuel consumption and energy utilization.For the identification of delays, a contextbased system could be required in order to help optimize the haulage cycle time by controlling delays in loading, haulage and dumping. After applying this methodology, efforts were focused in correcting out-of-standard performance values."

Jan 1, 2015

By D. Yuan, M. Sitter, S. St. Jean, M. Collins

The Ambatovy Joint Venture comprises an operating lateritic nickel mine, ore slurry pipeline, pressure acid leach plant and nickel refinery in Madagascar. The hydrometallurgical process selected by Sherritt for treatment of the Ambatovy ore is a long-term, sustainable approach to producing nickel. Sulphur, used to prepare hydrogen sulphide, which is used to produce mixed sulphide intermediate, is recovered in the refinery as ammonium sulphate fertilizer. Additional sulphur is used to generate sulphuric acid for treatment of the ore in the high pressure acid leach (HPAL) step; fossil fuel consumption is minimized by using the heat generated from the exothermic reaction between sulphur and oxygen in the acid plant to produce power and steam. Steam consumption is minimized by design of efficient flashing and preheat systems for HPAL, while the high temperature of the HPAL step serves to minimize acid consumption. Fossil fuel consumption by the operation as a whole is further minimized by locating the leach plant and refinery near the port of Toamasina and utilizing a 220 km slurry pipeline to transport ore from the mine to the leach plant. In addition, Ambatovy has demonstrated a strong commitment to sustainability programs such as the biodiversity management program at the mine and local procurement in Madagascar. In this paper, the hydrometallurgical process for nickel and cobalt recovery from Ambatovy ore is described, along with highlights of Ambatovy’s approach to sustainability in Madagascar.

Jan 1, 2015

By Piet Halliday, Ellina Kharatyan

Conventionally, emulsion matrices (unsensitized) need to be sensitized to become detonable explosives. This is done either chemically or mechanically. Both methods have their advantages and disadvantages. Mechanical sensitization involves the addition of microballoons (plastic or glass) to the emulsion matrix, in order to create hot spots during detonation. This is usually done at the manufacturing site and poses a safety risk in terms of the storage, transportation and handling of a 1.1 type explosive. Many countries throughout the world make use of chemical sensitization as opposed to mechanical sensitization as this allows for the storage, handling and transportation of two 5.1 type products rather than the 1.1 type explosive. Chemical sensitization involves the addition of a small amount of a chemical that reacts with a component of the emulsion matrix causing the formation of gas bubbles that act as hot spots during detonation. The disadvantage of this is the lack of accurate density control (due to various factors affecting the reaction) and the lack of comprehensive understanding of the operators of the reaction. This can easily result in poor blast performance. Due to these disadvantages a pumpable, non-detonable (5.1 type) mechanical sensitizer was researched and developed. This product allows for pumping at a 50:50 volume ratio with the emulsion matrix, when loading into blast holes. The significance of this is that a 1.1 type explosive is formed in the blast hole. As such, the security and logistical issues of the transportation and storage of the 1.1 type explosive are eliminated. Another advantage is accurate density control of the final product, specifically in small diameter long hole applications. A cost effective, unique mini pumping system has been developed for the loading of this product. Moreover, this system can easily be used for secondary blasting applications and the on-site packaging of cartridged explosive products.

Jan 1, 2015

By Chandrasegaran, Tamilmani

"This paper describes a case study of a retaining wall structure using a diaphragm wall to construct a stilling basin at Tanjung Bin T4 power plant in Johor Bahru, Malaysia. The stilling basin is part of the Phase IV (T4) 1x1000MW power plant’s offshore cooling water discharge culverts. The site is located close to the sea with 5m of fill on top of very soft sediments of marine origin up to 20m thick underlain by fluvial clay and metasedimentary rock. Stringent wall deflection criteria and construction program dictated adopting an efficient solution with 800mm thick diaphragm wall supported by permanent top support as the temporary prop and improved horizontal restraint provided by deep mix piles acting as a slab (ground improvement layer) below the final excavation level. The depth of excavation is about 10.12m from the existing ground level. The proposed solution kept the wall deflection below the limit of 0.7% of the depth of bulk excavation and avoided additional props leading to faster completion of the structure. With unsymmetrical loading behind the retaining walls, 2D finite element analysis was carried out to assess the wall deflection and stresses in the wall and the grout layer below. The diaphragm wall is instrumented to monitor the behavior and the findings are discussed in the paper.INTRODUCTIONConstruction in soft marine clay has always been a challenge to the engineer because of its very low shear strength and its sensitivity to disturbance. In the case of excavation projects the problem becomes even more complicated with development of excess pore pressure during excavation. Marine clay with its low shear strength and lesser passive resistance, generally leads to large wall movements and settlement behind the wall. Increased passive resistance coming from increased number of props is useful but has its limits and it is no longer the most effective way in containing or reducing the wall movements or forces in the wall. One of the solutions to these problems is to improve the soil shear strength by means of ground improvement infront of the wall at an elevation most appropriate to maximize wall performance. There are several methods adopted in improving a soil layer including mixing additives to the ground to improve the shear strength to partially replacing the weak soil while others are fully replacing the weak soil. This paper discusses the case study of approximately 10m of excavation in soft marine clay using 800mm thick diaphragm wall supported by Deep Mix Piles (DMP) being used to improve soft marine deposit to form a slab just below the formation level and thus improving passive resistance significantly. The ground improvement layer helped to reduce the wall forces and deflections making it possible to remove the need for additional temporary props leading to significant savings is time and productivity. The paper presents the various options explored before this method is adopted, the design approach, instrumentation data and the monitored results."

Jan 1, 2015

By Marko Lampi, Marc Nicolle, Janne Karonen, Kari Valkama

"In the ten years from 2003 to 2013 global mine production of copper has increased by over 23% to meet demand while the weighted average head grade has dropped from 0.9 to 0.7% Cu. These divergent trends of increasing demand and declining economic grades will extend the life of many existing mines and improve the viability of marginal and/or complex copper deposits. Against that context this paper outlines hydrometallurgical copper sulphide leaching options as alternatives to the more conventional pyrometallurgical processing route of copper sulphides. Three copper sulphide leaching and refining processes are discussed: total pressure oxidation, ferric sulphate leaching and copper chloride leaching. The effect of mineralogy on the choice of processing technology is discussed as well as some of the unit processes used. Additionally, possible benefits that a hydrometallurgical process may offer over an existing pyrometallurgical route are discussed. Subsequently, two very important aspects to the development of projects involving the leaching of copper sulphides are discussed. Finally, a number of conclusions are presented that will be useful to keep in mind when considering projects involving the leaching of copper sulphides. INTRODUCTION In the ten years from 2003 to 2013 global mine production of copper has increased by over 23% to meet demand while the weighted average head grade has dropped from 0.9 to 0.73% Cu (Murphy, 2014). If these divergent trends of increasing demand and declining economic grades continue, they will contribute to the extension in life of many existing mines and improve the viability of marginal and/or complex copper deposits. Against that context, this paper outlines hydrometallurgical copper sulphide leaching options as alternatives to the more conventional pyrometallurgical processing route for copper sulphides. Three copper sulphide leaching and refining processes are discussed: total pressure oxidation, ferric sulphate leaching and copper chloride leaching. Ferric sulphate leaching and copper chloride leaching are carried out at atmospheric pressure while total pressure oxidation takes place at elevated pressures."

Jan 1, 2015

By Marc-André Villiard, C. St-Onge, V. Silla, J-C Milot

Rio Tinto Fer et Titane (RTFT) operates a metallurgical complex in Sorel-Tracey, Canada. In the Ore Preparation Plant (OPP), ilmenite ore is roasted through four parallel rotary kilns generating 95% of the plant wide sulphur dioxide (SO2) emissions. RTFT proactively set an annual emission cap for SO2 to be achieved by 2015. To achieve this targeted SO2 reductions, a technology evaluation and selection exercise was carried out, followed by detailed engineering and implementation. After a detailed evaluation of SO2 scrubbing technologies, the Circulating Dry Scrubber (CDS) system was selected as the most appropriate desulphurization system for this application. The system was implemented and commissioned from 2013 to 2015. General performance testing conducted in May 2015 demonstrated that the system achieved and surpassed the anticipated design values in terms of SO2 removal efficiency and hydrated lime utilisation. This paper summarizes the SO2 technology selection process, design features of the selected technology, project implementation and final performance testing of the SO2 abatement system.

Jan 1, 2015

By P. James

"INTRODUCTION Dissolved salts build up in leach solutions over time as leach solutions mature. Iron can be particularly problematic for hydrometallurgical copper production as it can compete with copper for separation during solvent extraction (SX), leading to iron bleed through and reduced electrowinning (EW) efficiency. In its ferric form (Fe+3) it precipitates as a hydroxide at fairly low pH and can promote clogging and disrupted flow within leach pads as a result of localized pH deviations – such as might result from weather events. The solids formed can cause relatively irreversible degradation to pad productivity. The precipitation pH point for solids formation falls as the ferric (Fe+3) concentration increases, making the issue more prevalent as leach circuits for ore bodies containing appreciable iron get older. It can also be more of a concern when leaching lower grade ore like tailings where lower copper content may increase iron/copper ratios which may increase iron accumulation rates. The precipitation pH point for solids formation falls as the ferric (Fe+3) concentration increases, making the issue more prevalent as leach circuits for ore bodies containing appreciable iron get older. It can also be more of a concern when leaching lower grade ore like tailings where lower copper content may increase iron/copper ratios which may increase iron accumulation rates. Control of ferric (Fe+3) levels could be used to lower ferric (Fe+3) levels and keep the ferric hydroxide [Fe(OH)3] precipitation pH sufficiently high to avoid the associated solids formation and potential leach pad occlusion. Control of ferric (Fe+3) and ferrous (Fe+2) tenors and ratios may also provide benefit for improving sulfide ore leaching or bioleaching performance and effectiveness. Traditionally options for such control were rather limited with bleeding contaminants off or chemical dosing treatments being prominent methods. Now Blue Planet Strategies introduces a new option. Blue Planet Strategies (BPS) focuses on improved resource utilization targeting electrolytic treatment and waste conversion into resources and has now demonstrated that its proprietary DeMet™ (Dynamic Electrolytic Metal Effluent Treatment) platform is highly effective at efficient low-cost conversion and control of iron content in leach streams in addition to targeted dilute metal recovery.[1-6] This powerful new capability provides a new treatment opportunity to control leach solution ferric (Fe+3) and ferrous (Fe+2) tenors to enhance leach operation production."

Jan 1, 2015

By V. Shumila, T. Butler

Microseismic monitoring systems listen to a rockmass and record ground vibrations associated with brittle rock fracture. Modern systems record continuously and can identify as many as one thousand small and possibly larger magnitude events occurring each day from induced stress change and redistribution. This paper presents examples of the real time use of microseismic information in mining applications. It shows how alerts can quickly identify large magnitude events or unexpected clusters of seismicity and how seismic re-entry protocol can help to improve safety decisions. Additionally, newly developed advanced analysis techniques applied to mine seismic data sets are shown including the use of clustering methods to see into a cloud of seismic data to identify significant activity and quantify possible planar features. The use of source parameter trend analysis is shown to be a beneficial method for interpreting changes in relative stress levels. Seismic moment magnitude distributions are analyzed using the TGR (Truncated Gutenberg Richter) and TMD (Tapered Moment Distribution) methods to estimate bvalue and expected maximum magnitude. Seismic hazard analysis is shown as a useful way to simplify a dataset and highlight seismic hot spots. The rockmass response to excavation is a complicated spatial and temporal process and microseismic monitoring is a method that can be used to help understand the location and mechanics of failure occurring in the rock ultimately helping to improve safety and productivity at a mine site.

Jan 1, 2015

By M. Bustin, A. Hosseinian, G. Preisig

Hydraulic fracturing and hydraulic shearing techniques are essential for the development of unconventional oil & gas and geothermal resources. Such techniques will also play a key role in the development of CO2 sequestration, and management of high stresses encountered with deep mining. However, the optimal design of hydraulic injections is often limited by continuum treatments of the rock mass without consideration of the influence of the natural fractures present. These may interact with the hydraulic fracture to promote offsets or arrest, or may cause the natural fractures to undergo shear and dilation. Given the limited access to the rock afforded by deep boreholes common to oil & gas and geothermal projects, advanced numerical modeling is critical for understanding key mechanisms and interactions. In this work, we first present a coupled hydromechanical distinct-element model focusing on the propagation of a hydraulic fracture. Normal and shear displacements arising from the generated hydraulic fractures are subsequently integrated into a fracture flow model for detailed analysis of specific flow behaviour and fracture permeability. For this, a scanned 3-D profile of a natural fracture is used to correlate surface roughness to dilation as a function of shearing. Fracture flow is computed at different time steps corresponding to different fracture propagation states and geometries. Modeling results indicate that the opening of a tensile hydraulic fracture is accompanied by millimetre-scale shear displacements associated with slip and wedging between adjacent blocks. This may leads to a mismatch between the upper and lower walls of the fracture if asperities are irregular and strong enough. However, fluid-induced tensile fractures have low Joint Roughness Coefficients (JRC), and associated millimetre-scale shear displacements are too small to ensure a significant offset of asperities that prevent a fully-elastic closure when the hydraulic fracture is depressurized. Injection of proppant is thus critical to keeping hydraulic fracture apertures open. Future work is planned that will see the models calibrated against field data including microseismic event locations, magnitudes and source mechanisms, tiltmeter deformations, stress change, and pore pressures.

Jan 1, 2015

By W. R. Reed, D. E. Pollock, T. W. Beck, J. A. Organiscak, J. D. Potts

"In underground continuous mining operations, ventilation, water sprays, and machine-mounted flooded bed scrubbers are the primary means of controlling respirable dust exposures at the working face. Changes in mining arrangements, such as, face ventilation configuration, orientation of crosscuts mined in relation to the section ventilation, and equipment operator positioning, can impact the ability of dust controls to reduce occupational respirable dust exposures. This study reports and analyzes dust concentrations measured by the Office of Mine Safety and Health Research for both remote-controlled continuous mining machine operators and haulage operators at ten U.S. underground mines. Results of these respirable dust surveys show that continuous miner exposures varied little based on depth of cut, but are significantly affected by ventilation configuration. Haulage operators experienced elevated concentrations in blowing face ventilation. The type of cut influenced exposures, with elevated exposures observed for both continuous miner operators and haulage operators when working in crosscuts driven into, or counter to, the section airflow. Individual cuts are highlighted to demonstrate instances of minimal and excessive dust exposure attributable to particular mining configurations. These findings form the basis of recommendations for lowering face worker respirable dust exposures when performing a variety of continuous mining cuts.INTRODUCTION Underground continuous coal mining operations may encounter a wide range of conditions and arrangements during production and development activities. These activities typically produce respirable coal mine dust, putting operators of continuous mining machines and coal haulers at risk for elevated exposures. In order to comply with federal regulations limiting respirable dust exposures for the duration of a working shift, mine operators typically implement ventilation, water sprays, and machine-mounted flooded-bed dust collectors (scrubbers) to dilute and control mine dusts during coal cutting. Nevertheless, changes in operational conditions can limit the ability of these controls to effectively reduce dust exposures. Some examples of conditions that can change during the course of mining include face ventilation configuration, orientation of crosscuts mined in relation to the section ventilation, and operator positioning. Because these arrangements are largely under the control of mine operators, any insight into associated exposures may inform future plans and behaviors, reducing occupational exposures to respirable dust. The objective of this OMSHR study is to evaluate respirable dust exposures associated with a range of continuous mining arrangements by comparing occupational dust concentrations measured during a series of field surveys. These comparisons consider face ventilation configurations, depths of cut, and crosscut mining practices."

Jan 1, 2015

By Ali S. Fayad

"In June 2014, Orange County Flood Control District (OCFCD) completed construction improvements of the East Garden Grove-Wintersburg Channel for a price of $42 million. Instead of the pre-existing traditional trapezoidal levee, the channel was improved with a vertical compact levee. Dubbed Soil-Mix-Sandwich (SMS), this geo-structural and environmental solution for coastal channel improvements, underlain by liquefiable soil strata, was both a design and construction innovation. It employed Deep Soil Cement Mixing (DSCM) within the confines of a hydraulically-pressed (Giken Method) sheet pile duo. SMS was unique because it incorporated both subterranean and supra-dredge-line soil mixing within a very narrow workspace. Its DSCM pattern aimed at optimum densification of the workspace and was confirmed during the construction process. It availed the DSCM sub-contractor (Hayward Baker Inc.) the opportunity to demonstrate the fitness of their huge wet-mixing machinery within a very confined access-area and introduced approximately 70,000 cubic yards of DSCM within a limited 15 foot workspace width that stretched for a mile. The sheet pile duo created a construction-enclosure that became a stay-in-place load resisting system. PROJECT CHRONOLOGY AND LOCATIONAn Orange County Flood Control District (OCFCD) project-report was commissioned to study the East Garden Grove Wintersburg channel (OCFCD facility # C05). The report examined the hydraulic conveyance of the C05 channel and was concluded in 1994 by Williamson & Schmidt. The project-report did not encompass extensive geologic studies; but it provided several alternatives for channel improvement. It recommended a single row of sheet piles as the preferred alternative for the downstream reach.The most downstream reach of the C05 channel is located in an environmentally sensitive area, in City of Huntington Beach, California, USA. Its site includes seismic chasms that surface within the C05-footprint (the Newport- Inglewood tectonic fault). Extensive deposits of liquefiable soil exist beneath the channel. Furthermore, tidal-influence prevails against the channel levee. Implementation of a successful design for channel improvement emerged after several traditional concepts were deemed unacceptable by geotechnical consultants. OC Public Works (on behalf of OCFCD) was in need of a design and construction technique that mitigated many associated risks. From these circumstances, Soil-Mix-Sandwich was born and was referred to in the rest of this discussion as SMS. OC Public Works required the SMS design concept to undergo verification by independent geotechnical consultants. SMS chronology from conception to construction can be summarized as follows:"

Jan 1, 2015

By George Filz, Morales, Carlos, Bertero, Filippo Maria, Alessandro, Leoni

"The Deep Mixing Method (DMM) represents a viable solution to improve adverse geotechnical properties of foundation soils for many practical applications. A pre-construction soil investigation campaign is necessary to assess soil properties and to retrieve samples of different soil layers for a laboratory Bench Scale Testing program (BST). The BST has to be designed using various binder types, binder contents, and water/cement ratios in each of the soil types. Following the laboratory program, a full scale Field Test (FT) is typically necessary to verify the results of the BST. This paper will highlight the differences and the importance of performing both pre-construction laboratory tests and field tests to ascertain the proper mixing parameters in the different soil layers. Comparative analyses and interpretations between the lab and field stages, along with accumulated information about soil properties and quality control (QC) results, allow fine-tuning the production parameters throughout a project. Three Deep Mixing Method projects, where both laboratory and field tests were executed, are illustrated: (1) The LPV 111 Project (New Orleans, LA, USA): DMM was used for ground improvement/foundation strengthening to stabilize and support the burden of a new levee raise; (2) The Rio Puerto Nuevo Project (San Juan, PR, USA): DMM was applied to improve the soils adjacent to a 90"" forced sewer main relocation and to improve the soils for the base of a new drainage channel; and (3) State Road 83 (US 331) over Choctawhatchee Bay project (Walton County, FL, USA): DMM was applied to stabilize the causeway sections of the bridge enhancement project. Data recorded during laboratory and field tests for these projects were analyzed and interpreted to select the most appropriate construction parameters to provide a final high-quality product.INTRODUCTIONThe Deep Mixing Method (DMM) represents a viable solution to improve adverse geotechnical properties of foundation soils in many situations. The effectiveness of working parameters depends largely on the physical and mechanical properties of the soil to be treated. Therefore, well designed laboratory and field test programs, aimed to disclose the interaction between the site-specific soils and the mixing parameters, are essential to achieve the desired end product.Generally a pre-construction soil investigation campaign has to be performed to assess soil properties and to retrieve samples of different soil layers for the laboratory Bench Scale Testing programme (BST). The BST has to be designed using various binder types, binder contents (or cement factors - CF), and grout water/cement ratios (W/C) in each of the soil types; the selection of the different combinations and dosages for the BST is based on past extensive experiences on similar materials. Following the laboratory programme results, a full scale Field Test (FT) has to be designed and executed, installing several DMM elements to verify the results of the BST and fine tune the construction parameters, with the appropriate binder type and dosage and the most effective equipment and tool configuration."

Jan 1, 2015

"With millions of dollars and thousands of lives at stake, the Iron Ore Company of Canada (IOC) turned to a private wireless network for help.IOC needed a network that possessed the ability to adapt to changes in a nanosecond and to function seamlessly in the most rugged of environments.Canada’s largest iron ore producer required a private wireless network powerful enough to support all mine applications and deliver all data to one central point — without any existing cellular/3G/Wi-Fi coverage.Operations at IOC, a leading global supplier of iron pellets, involved dispatch, drill management and equipment monitoring, pump control and remote video that must service three distinct pits. Due to its setup, the facility does not offer a great deal of flexibility for transmitting signals.IOC serves a robust customer base made up of North American, European and Asian steel producers. It also employs nearly 1,900 people. Catastrophic death and destruction are two very real potential consequences of system communication failure.Technology for tough terrainKinetic mesh technology was born in the wake of the 9/11 terrorist attacks on the United States, one of the most high-stakes emergency situations in U.S. history. The failure of the communications infrastructure on a massive scale that day underscored the need for networking technologies that could provide service even in the most chaotic of conditions.Kinetic mesh networks allow organizations to deploy networks at sites where communications infrastructure has been compromised, as well as quickly establish networks in places where they did not previously exist. Kinetic mesh networks have also demonstrated a better ability to adapt to network changes on-the-fly versus other types of networking technologies."

Jan 1, 2015

By C. Grisanti, E. Prina Howald

The major of Swiss territory is occupied by mountains. Natural events as floods, debris flows, landslides, rockfalls, and avalanches regularly threaten the safety of people and properties. On the one hand, extreme weather events cause great damages, on the other hand, the enhancement of territory’s exploitation increases the risk. The Swiss Government makes many efforts to deal with the prevention of natural hazards, especially through measures of land management. As stated by federal law, Swiss cantons are obliged to establish hazard maps and to take the risk into account in the land management. Hazard maps are based on the hazard matrix, whose abscissa and ordinate are probability and intensity of the event on site. This project focuses on rockfalls. It consists of three main parts: the creation of a database to collect data on site, the creation of a catalog with all type of measures, and the development of a methodology for the analysis of the effectiveness of protective measures. The creation of the database allows us to collect information: about the site, about protective structures implemented on it, and about failures. With many multiple choice fields and few free text fields, it can collect data in a homogeneous way, without redundancy. The catalog has to be a tool that gives a basis to make decisions. It collects information about all types of protective measures implemented on Canton Vaud’s territory or available on the Swiss market. Free text fields allow for data storage of specifics, to give a complete view of structure’s characteristics and potentials. Methodology consists of four steps. The core of the procedure is the structure’s evaluation following a score system; it allows for calculation of reduction factors that have to be applied to intensity and probability parameters of the structure. Then it is necessary to convert the reduced structure’s intensity value into a residual site’s intensity value. Although the first step enables us to choose suitable measure for a specific site, it is not necessary to perform it. Second step allows us to evaluate structures under scenario 0, where structures are in best conditions. Third step allows us to evaluate structures under six scenarios of possible failings. Fourth step allows us to convert structure’s reduced intensity into event’s residual intensity and to establish the new point on hazard matrix. While the procedure has already been defined, details of score system and conversion have to be developed during the second phase of the project.

Jan 1, 2015

By Nan Zhou, Jixiong Zhang, Qiang Zhang

"Mining activities under hard roof could easily induce rock burst. Based on the geological conditions of widespread hard roof in China, this paper discusses the type, mechanism of occurrence and prevention of rock burst caused by hard roof from energy evolution point of view. It analyzed the interaction between the solid backfilled body and roof under different backfilling ratios. And by establishing and applying the mechanical model, the deformation of hard roof and energy evolution of the panel under different backfilling ratios were determined, revealing the control effect of solid backfilling on disaster-causing energy. As a result, an innovative method using the solid backfilling method was proposed as a solution to the hard-roof-induced rock burst hazards. Moreover, mine trial was conducted in Panel 6304-1 of Jisan Mine. The result shows that the stress concentration factor of the front abutment stress was only 1.44; the coal dusts in drill holes didn’t exceed the limits and microseism of large energy didn’t occur during mining mining, indicating that solid backfilling mining could be applied as an effective method for preventing rock burst caused by hard roof.INTRODUCTIONSHard roof refers to the thick strata above the coal seam or thin immediate roof. It is strong with poor joint development. After mining, instead of immediate caving, it will overhang for a large area in the gob, resulting in high stress in front of the face and difficulty in gas dispersion. As a result, the face spalls, the roof exposes and the gas accumulates in the gob. With the continuing advance of the face and increase in area of overhang, the stress in the hard roof will eventually exceed its ultimate strength and cause a large area of caving, followed by quick release of energy concentrated in the roof and coal seam, which may cause rock bursts and other dynamic disasters in the mine as well as serious equipment damage and casualties. Therefore, the hard roof becomes one of the main factors causing rock bursts at the face.Hard roofs in China varies in conditions. It ranges from dozens of meters to hundreds of meters in thickness. However, coal reserve under hard roofs accounts for about 1/3 of the total reserve; moreover, nearly 40% of the fully-mechanized coal mining panels are those with hard roofs and more than 50% of the mining areas are associated with problems of hard roofs. Aiming at this problem, researchers at home and abroad have proposed many solutions, e.g. coal pillar support, strength weakening and forced caving, to prevent rock bursts caused by hard roof. These solutions have been employed in some cases with good results. However, due to the variability in geological conditions of mining and hard roofs, the application of the above solutions is limited."

Jan 1, 2015

By David W. Martel, Tom George

"As part of the regional water authority review and upgrade of local dams a 35m x 5m x 3m wet soil mixed block was required for stabilisation of a dam wall toe in remote Victoria, Australia. Remote access, extremely poor roads and high mobilisation costs made more traditional CSM and deep mixing methods cost prohibitive. The dam required a redesign to raise the wall by 2.0m to increase water storage. Additionally, the dam required additional stabilisation to reduce the risk of liquefaction during an earthquake event. Soil testing indicated loose, cohesionless, high permeability soils to a depth of 3.0 to 3.5m across the toe of the wall. This resulted in high dam seepage through the toe of dam wall potentially causing the factor of safety during a seismic event to decrease to a dangerous level. A number of laboratory trials were completed to determine the mix ratio of cement required to improve the strength of the saturated, liquefiable soil.Wagstaff Piling was responsible for achieving the required soil/cement strength and mix depth on site. As the ground conditions were too soft for conventional soil mixing equipment, an excavator mounted Mitsui road header was modified to fit a 20 tonne excavator. A purpose built remote batching plant was set up on more stable ground approximately 200m from the wall and utilised for preparation of cement and water slurry for supply to the machine. As the ground was too soft to support the excavator, the progressively improved ground was used as the working platform. Both wet grab sampling and in situ testing was undertaken to determine the UCS of the improved soil. These results indicated several variations in the results due to size effects.1 INTRODUCTIONA small town in remote Victoria relies totally on its water supply from a small dam. The dam wall required stabilisation works by ground improvement as studies completed on the dam classified it as a high risk of failure under an earthquake event. In addition, the earth fill dam had high levels of seepage and poor control measures, requiring the dam to be upgraded to comply with all regulations.The relevant water authority engaged a contractor under a design and construct contract to complete the works. Wagstaff Piling was engaged as the Subcontractor to provide design and construction advice including the contract for the ground improvement works. Initial discussions involved CSM walls, cut-off walls and mass soil mixing solutions. However, due to the access restrictions for piling equipment, mass soiling mixing was the chosen method of ground improvement."

Jan 1, 2015

By M. S. Celik, H. Du, J. D. Miller, F. Cheng, O. Ozdemir

"In this paper, recent progress with respect to the flotation chemistry of soluble salt minerals is reviewed, and some of the more relevant issues including the hydration states of ions, the interfacial phenomena of salt surfaces and the flotation behavior of selected soluble salts are discussed. Due to the high solubility, the flotation of most soluble salts has to be carried out in their saturated brines. Anecdotal evidence has suggested that the hydration states of the ions have significant influence on the physicochemical properties of the solutions, the surface charge and wetting characteristics of the minerals, the collector adsorption states and, further, the flotation behavior of the soluble salts. In this regard, reviewing past research findings, efforts are made to establish a correlation between the ion hydration states with the flotation behavior of the soluble salts. Further, advances in understanding the significance of colloid adsorption involved in the soluble salt flotation process are addressed, and future research efforts to understand the soluble salt flotation chemistry are suggested.IntroductionSoluble salt minerals are essential raw materials for the production of a variety of commodities, fertilizers, potassium hydroxide, soda ash, magnesium compounds and other chemicals. These soluble mineral resources can be processed using flotation technology and, currently, more than 80% percent of the world’s potash is produced by the selective flotation of KCl crystals (sylvite) from other salt crystals, predominately NaCl (halite) and other more complex salts (Searls, 1990). Despite the successful application of flotation technology in the potash industry, the mechanisms for collector adsorption on soluble salts have not yet been fully understood and, therefore, have been of considerable interest to flotation researchers for many decades."

Jan 1, 2015