Search Documents

By Jian-bin Xie, Lin-fang Shen, Zhi-liang Wang

"In order to research temperature field for construction of connecting passage in Metro using artificial freezing method, the finite difference software FLAC3D is employed to numerically simulate construction process of connecting passage. During construction, the overall distribution of temperature field around connecting passage, the relationship between soil temperature and freezing time, the distribution and variation for the thickness of freezing wall are studied from the perspective of numerical analysis. The results show as follows: after 55 days’ freezing, the soil temperature surrounding connecting passage is about -24 oC ~ -28 oC, and the minimum thickness of freezing wall is about 4.0m, which is larger than the design value 3.1m. So construction conditions have satisfied to the excavation of connecting passage and pumping station. During the excavation of connecting passage, soil temperature has almost no obvious change and the thickness of freezing wall remains constant mainly. After 45 days’ normal thawing, the temperature of freezing wall rises 12 oC approximately. And the soil temperature rises faster at the beginning of the normal thawing stage. In the whole process of construction, the frozen area is about 5m outside the edge of connecting passage, and the cooling area is about 10m outside the edge of connecting passage. INTRODUCTIONThe first recorded application of the artificial freezing method is on a mineshaft project in 1862, and it has been widely used in foundation pit engineering, subway tunnels, mine shaft engineering and so on (Wang Zhiliang, 2010; Zhang Juanxia, 2012; Qiu Fan, 2007; Zhou Xiaomin, 1999). This method has many advantages of enhancing soil strength; decreasing permeability and adopting various unstable soils (silt clay, sand, gravel, etc.). It has been applied successfully in metro engineering construction in Beijing, Shanghai and Nanjing. According to incomplete statistics, the construction of connecting passage using artificial freezing method accounted for 98% in Shanghai metro (Qiu Fan, 2007)."

Jan 1, 2015

By A. D. S. Gillies, A. Haghighat

"A study has been undertaken at the Missouri University of Science and Technology (MS&T) limestone Experimental Mine to determine new fans set up and wiring options.to install additional mine ventilation capacity. Selection for main fans has been undertaken according to the mine’s required performance specifications and fan characteristics. Available fans for ventilating the mine are Joy and Alphair axial fans each of 24 kW each and two Spendrup booster fans of 12 kW each. The installation of main mine fans on the surface and underground entails numerous considerations. Design of a ventilation network for the Experimental Mine incorporating surface and booster fans has been accomplished using Ventsim Visual program software. The ventilation network has been separated into two segregated parts. A main surface fan and a booster fan have been used in each segregated part of the network. The mine has had a vane axial Joy fan in place for many years. The Alphair 4800 VAX 1800 full blade adjustable pitch vane axial fan was selected and installed as the other surface fan and eventual replacement for the Joy fan. Main surface fans have been connected individually to booster fans in series. The Alphair main surface fan has been installed vertically. Four different wiring options and related cost estimations for addition of the new main fans to the ventilation network have been considered. The analysis resulted in an innovative steel frame design used to allow the fans, when necessary, to be moved to the side of the shaft so that blast pressures do not damage the blades. INTRODUCTION Main fans are the heart of a mine’s ventilation network and play a key role in supplying required airflow (Haghighat, 2014). The Missouri S&T Experimental Mine has been developed in uniform limestone with few stratigraphic features. The mine floor is approximately horizontal and water drains well. A study has been carried out on MS&T Experimental Mine. Selection of main fans has been undertaken according to the mine’s required performance specifications and fan characteristics. Ventsim Visual computer simulation has been used to assist in design of the ventilation network. Wiring circuits, fan foundations and flexibility have been considered as the three main parameters for surface fan installation at the Experimental Mine. Two surface and two underground wiring options and three surface set up options and related cost estimates for the new surface fan system were investigated. Frequent use of explosives in the mine occurs throughout each year. Flexibility in changing the position of a surface fan is important. A number of options have been considered for the location of a vertical main fan positioned on the upcasting shaft. The mine is used for a variety of purposes and flexibility has a high priority amongst design considerations."

Jan 1, 2015

By C. Dirscherl

"Declining ore grade, leading to increased material transport and plant throughput requirements, is one of the major challenges in the current mining environment. This is accompanied by rising energy and labor costs, decreasing plant productivity and the requirement for highest plant availability. Siemens’ answer is the latest gearless drive technology for grinding and conveying. Gearless drive solutions are surpassing the mechanical limits of conventional drive systems serving to utilize the principle of economies of scale. By elimination of various components of the drive train the maintenance activities and spare parts inventories are reduced. The advantages are culminating in the incomparable availability of the Siemens’ gearless drive technology of 99.46 to 99.71% - as confirmed by real operational data from the Antapaccay mine in Peru. It was the first plant worldwide to use gearless drives for both applications. KEYWORDS: Gearless Mill Drives, Gearless Conveyor Drives, Availability, SAG Mill, Ball Mill, Overland Conveyor, Antapaccay INTRODUCTION – THE GEARLESS PRINCIPLE The principle idea behind a gearless drive system is to reduce the number of components and diversity of parts. Especially those components that are at the edge of current manufacturing or power limits are eliminated. The used equipment provides the possibility to scale up and increase the power transmitted to the driven machine. This finally results in a possible increase of throughput respectively transported or processed material. In order to apply this principle of simplification we will take a look at the components of a conventional drive system consisting of: - Driven equipment (mill, conveyor, slurry pump…) - Components altering the rated speed (gearboxes, girth gear / pinion) - The electric motor - Starting devices for the motor (VSD, CCV, LRS, clutch…), which are necessary because a direct across-the-line start of high power motors with load would result in a significant drop in the line supply voltage - Alternatively a variable speed drive (VSD) or cycloconverter (CCV) to utilize the possibility of speed variation during operation - The electrical supply system (cables, switchgear, transformers, protection equipment) Intermediate gearboxes are not required when a motor is used with a rated speed that directly matches the speed requirement of the driven equipment. Furthermore the VSD can be used to smoothly start the motor and to vary speed during operation, which means that it satisfies both requirements."

Jan 1, 2015

By R. Plassart, F. Laigle

"As a powerhouse, a transformer or a valve chamber, large underground caverns are a major element of hydropower plant. On the contrary to galleries and shafts which are linear and long underground structures, large caverns are designed with often complex geometries and large spans. Moreover, as these caverns are generally located on the foot of the hydraulic scheme, the high overburden is often responsible of a high stress state. Thanks to current experiences in France and around the world, the Hydro Engineering Centre (CIH) of EDF has defined great principles in the design of caverns leading to a more general methodology. The project of Tehri in India is an example of difficult ground, with in the same time a high overburden, a ductile material and an important schistosity. These physical realities are attempted to be approached in numerical modelling thanks to a constitutive law with softening behaviour and an oriented criterion integrated in the continuum model. As a result, a flexible support is advised, based on a high density bolt system and a thin lay of shotcrete. This methodology has been developed in the case of Gilboa in Israel, except the schistosity which has not been observed in situ. At last, the example of Gavet (France) illustrates a discontinuous case of numerical modelling for a good quality but fractured rock mass.PRINCIPES ET METHODES DE CONCEPTION DE GRANDES CAVERNESHYDROELECTRIQUES SOUTERRAINESRESUME Les grandes cavernes souterraines abritant les turbines, les transformateurs et certaines vannes sont des ouvrages majeurs dans les aménagements hydroélectriques. A la différence des galeries et des puits qui présentent de longs linéaires, les grandes cavernes sont des structures à la géométrie souvent complexe et avec des portées conséquentes. De plus, ces cavernes étant généralement situées en pied du circuit hydraulique, la grande couverture rocheuse peut se traduire par un état de contraintes important. Forte de ses expériences récentes en France et dans le monde, le Centre d’Ingénierie Hydraulique d’EDF a identifié de grands principes de conception des cavernes permettant l’élaboration d’une méthodologie plus générale. Le projet de Tehri en Inde est un exemple de terrain difficile, présentant à la fois une forte couverture, un matériau ductile et une schistosité marquée. Ces réalités physiques sont approchées au mieux grâce à la prise en compte dans les modélisations numériques d’une loi de comportement radoucissante avec un critère orienté intégré dans un modèle continu. Les résultats ont conduit à privilégier un soutènement souple basé sur un boulonnage systématique relativement dense associé à une fine couche de béton projeté. Cette méthodologie a ensuite été reprise pour le projet de Gilboa en Israël, exception faite de la schistosité puisque non observée sur site. L’exemple de Gavet (France) enfin permet d’illustrer un cas de modélisation numérique discontinue d’un massif rocheux de bonne qualité mais fracturé."

Jan 1, 2015

By A. McGrath, M. Trovant, M. Haque

Minimizing energy consumption is a priority for many industrial facilities. Metallurgical and gasification processes produce dirty syngas (CO and H2), which offers the potential for energy recovery. However, syngas handling can pose an explosion risk and even minor leaks can result in poor workplace hygiene. Furthermore, many jurisdictions around the world now discourage wet syngas handling due to limited water availability and secondary pollution. Hatch has developed a 100% positive pressure gas handling system that targets these safety hazards without using fresh water. The implementation of a system for calcium carbide smelters at Qinghai Salt Lake Industry Co. (QSLIC) in China is profiled as a case study.

Jan 1, 2015

By J. P. Harrison, N. Bozorgzadeh, M. Dolowy-Busch

"It is common in rock engineering practice to characterize the triaxial strength of intact rock by using only data samples of small size. Practical guidelines such as ASTM support such sample sizes. In this paper, we investigate the reliability of the Hoek-Brown strength criterion estimated from such samples. For this purpose, we use an unusually large published set of triaxial strength data to randomly select a large number of data samples of small size to simulate the situation that frequently encounters in practice. The samples are generated with different arrangements with regards to the confining pressure. We fit the Hoek-Brown criterion to each of these samples, obtain estimates of strength parameters and compare them to those obtained from the complete data set. Our analysis suggests that estimates based on small samples are not reliable and can lead to both over- and under-estimation of strength.Additionally, we use these small samples to investigate the statistical methods for obtaining design values of strength as suggested by limit state design standards such as Eurocode 7. We show that, if used in conjunction with small samples, these methods do not guarantee a safe estimate of strength and in many cases lead to highly over-conservative estimates.We present a potential solution to this problem by augmenting the small data sets with Bayesian informative priors to give much more reliable estimates of strength. We conclude with suggestions for the development of informative prior distributions."

Jan 1, 2015

By L. K. Sinclair

In situ leaching of copper has the potential to deliver low-cost recovery for soluble copper deposits of sufficient permeability. In order to provide key inputs for modeling of the in situ leaching process, bench scale test work can be used in conjunction with geochemical software to identify key leaching and precipitation reactions. A case study is presented in which a series of flow-through acid leaching tests were conducted on drill core sections from a porphyry copper deposit without crushing or grinding. Concentrations of copper and other key elements were monitored in the recirculating leach solution over several months. A geochemical model of each leaching test was prepared using Geochemist's Workbench using a combination of diffusion-controlled and reaction-controlled rate mechanisms. Key reactions included leaching of chrysocolla, iron oxides, and plagioclase. The model was able to simultaneously satisfy the evolving chemistry of the recirculating leach solution, mineralogy of the head and leach residue, measured acid consumption, and leaching rates for key minerals reported from previous laboratory studies. Opportunities and limitations for scaling up the model to simulate the commercial wellfield are discussed.

Jan 1, 2015

By J. O. Claassen

"SynopsisMining value chains are dynamic systems and should be managed according to systemic flow-based principles. This includes a detailed focus on the impact of variable geological conditions on material flow, product quality, and production cost, visibility of the total mining system to operators and managers, as well as the synchronization of resources and activities in downstream processes. Thirty mining operations across the African continent were studied to establish to what extent systemic flowbased principles are applied in day-to-day operations. The study indicated that although most mining operations have identified the relevant geoprocessing variables, only a small number apply this information in a flow-based management approach. Most mining operators do not focus on developing a clear flow view of the mining value chain and on making it visible to operators and managers to enable them to optimally set and reset operations. Daily synchronization of geoprocessing variables is limited to a small number of variables, e.g. synchronizing ore hardness with drilling or milling requirements, in less than 30% of the operations evaluated. Operations where these principles have been adopted reported a noteworthy improvement in performance. The study indicates that notable potential exists in most of the operations evaluated to implement flowbased management principles, including geometallurgical principles. This can significantly improve value chain performance without exorbitant capital layouts and enhance ROCE. IntroductionObjective of the studyThe study seeks to establish to what extent systemic flow-based principles have been adopted in the southern African mining industry and the implications thereof. Specific attention is given to the importance of defining and managing geoprocessing dependencies (geological variables directly impacting mining and plant performance – the geometallurgical approach), establishing a flow view of the mining system, which typically includes a dashboard of the flow of ore/product quality and cost from the mining face to the customer, and limiting the impact of dependencies through synchronization of activities and resources, e.g. ensuring that a continuous miner does not wait for a roofbolter, or that reagent addition rates are matched with a specific ore/concentrate composition."

Jan 1, 2015

By Chris Twigge-Molecey

Demand for metals will continue to grow as global population numbers and prosperity levels steadily increase. Consequently, there will continue to be a need to design and construct new metallurgical plants. Business success in general requires projects to be financially successful and return appropriate value to their owners. However, in the metals industry, private and public sector financing sources have become very sensitive to the perceived inability of projects to contain costs and meet other business objectives. Thus, the capital for projects has become more difficult and expensive to obtain. It is instructive to note that Ernst and Young (2011) identified that: “Delivery of predictable project results bestows competitive advantage and market confidence to those corporations who successfully instill this discipline”. The implication for future projects is that they must be systematically developed to minimize perceived risks—and more importantly—to demonstrate that the risks are managed to achieve the business case. Then, provided that the project has been developed in a well-structured way, project success can again be defined as a project with: a final cost within 10% of the budget approved at the end of FEL3, when the project is properly defined and the permit conditions are agreed upon; a start-up date within three months of the definitive, scheduled startup date; production levels at 85% of design capacity within a year of starting commercial operation; production meeting the target environmental restrictions; and with zero lost time accidents during construction and startup. The plant design is one of many integrated activities required to achieve these objectives. This book represents a valuable link between the existing engineering literature that encompasses a wide range of engineering fundamental textbooks and design manuals and the project management literature such as the Project Management Body of Knowledge, or PMBOK® (Project Management Institute, 2014). It is evident throughout this book, that the design team is a small but essential part of a much larger project team comprising the project management, construction management, and construction contractor staff. Design activities must be regarded and managed as part of the integrated whole, with two fundamental links throughout the design process:

Jan 1, 2015

By S. Tuylu, D. Adiguzel, U. G. Akkaya, A. Bascetin

"One of the main problems for storing of the tailings is acidity occurrence due to several factors such as existence of sulfuric minerals and also the pollution in seepage waters by mobilization of metal ions, which holds great risks in terms of environmental regulations. Because of these specified reasons, tailing materials to be used in a SPD formula should have comply with some specifications. Among these properties; oxygen content, temperature, matrix suction and pH are the most important parameters. In the study, the relationships between the parameters mentioned are investigated to reveal optimum paste design layout. The lowest amount of seepage water obtained from the paste layers in the pilot cabinet was found as 2150 ml from 3rd layer. As for the maximum seepage water and the average of the all 11 layers were found as 4909 ml from 6th layer and 3273 ml respectively. The reactions occurring according to the oxidation, as seen at seepage water of second and third layers, decreased the pH of system to the under of 7 value. Additionally, when the seepage water of first layer’s EC value is 2.93 mS/cm, the EC value of second layer is increased at 3.54 mS/cm. The other parameters are evaluated with the obtained results of the tests to determine the optimum storing conditions for SPD.INTRODUCTION Conventional waste disposal methods, although widely used, pose great environmental risks. One of the most important issues is acid mine drainage (AMD). Tailings of metallic mines contain heavy metals, aggressive chemicals and hazardous materials. In the presence of oxygen and water, an oxidation reaction can occur, causing a decrease in pH of the environment, and heavy metals that are present in the environment can dissolve easily. Subsequently, heavy metals can pollute underground water basins, creating a great amount of danger for the ecology and potable water resources. Another important risk associated with conventional waste disposal methods is accidents related to the waste dam. Higher volumes of water and tailings (usually 15% solids and 85% water by weight) are sent to waste dams, making it very difficult to control the stability of the dam under conditions such as static and dynamic loads (seismic activities, vibrations caused by blasting, etc.), flooding, and seepage. In case of an accident or failure, the spread of great amounts of mud containing hazardous chemicals and heavy metals can harm the environment of the dam site significantly (Bascetin et al., 2014). In the paste technology, depending on the type of ore, tailings used in the paste mixture can contain sulphide minerals (such as pyrite and pyrrhotite). These minerals are known to be reactive with water and oxygen to produce acidity (sulphuric acid)."

Jan 1, 2015

By D. F. Zhang, X. Q. Jiang, N. Tahreen, D. L. Chen, F. S. Pan, D. Y. Li

Alloying with rare-earth elements has been proven to be an important tool for magnesium to achieve superior properties via texture randomization. The role of yttrium in texture weakening and the link between texture and formability are fairly well known. Since annealing is a vital part of metal processing which could significantly contribute to ductility, it is important to ascertain the impact of annealing in terms of texture change. Also, an understanding about texture development during pre- and post-deformation annealing is essential to improve the industrial deformation processing as texture is closely related to formability. While there is independent information in the literature regarding the effect of rare-earth addition and heat treatment on the texture formation, no systematic studies have been reported on the collective impact of yttrium addition, annealing and deformation on texture evolution. The present study was, therefore, aimed to identify the inter-relationship among texture evolution, yttrium content, heat treatment and deformation behavior in an extruded Mg-Zn-Mn-Y alloy. Annealing at 450°C for 1 hour and uniaxial compression tests at a certain amount of deformation were performed. The deformed and annealed samples were then subjected to annealing and compression test, respectively, followed by texture measurements. It was observed that yttrium addition effectively weakened the crystallographic texture in all conditions, which was evident from the changes in the microstructures and textures.

Jan 1, 2015

By Yoshinori Kurumada, Masaya Watanabe, Kenji Sasa

"The Port of Yokohama is strengthening its international competitiveness as a strategic container port in order to respond appropriately to global exchange and shipping demands. Thus, the Minami Honmoku main Pier is currently being developed. The high-standard container terminals MC-1 and MC-2 have already started their service, and the development of the container terminals MC-3 and MC-4 is currently in progress.Because the South Honmoku Pier plays an important role in waste disposal management of Yokohama, a final waste disposal site (controlled final landfill site) is being developed in Block 5 to provide long-term and stable reception of waste that will be generated in the city. For this project, a revetment with water-blocking properties and an extension approximately 1.7 km in length is being built in order to prevent water from leaking from the disposal site. The base part of the revetment will be subjected to foundation improvement using the Cement Deep Mixing (CDM) method in order to secure water shielding of the soft sediment underneath the water, prevent slipping of the seawall, reduce the amount of subsidence, and increase the foundation support force.This report presents a preliminary study on using CDM on reclaimed soil and the construction process of the development project of the disposal site in Block 5 of the Minami Honmoku Pier, which has been underway since 2007.ABOUT MINAMI HONMOKU PIERThe development of the Minami Honmoku Pier started in 1990. It was designed to develop high-standard berths with greater water depths in order to handle the increasing volume of foreign container cargo and growing size of vessels. Figure 1 shows the layout of Minami Honmoku Pier. In April 2001, the Phase 1 (MC-1 and MC-2) began services. This is the newest pier in Port of Yokohama.This pier has one of Japan’s largest terminal areas (40 ha) and is equipped with 22 row-type mega gantry cranes capable of handling the newest ultralarge container ships. The pier has a quay with a water depth of 16 m, which is the first in Japan. The pier is equipped with advanced facilities and equipment to let Port of Yokohama be internationally competitive and function as an international commercial hub. An innovative system for high-efficiency transport is currently being introduced; it includes the installation of waiting vehicle lanes and a reservation-based loading and unloading system.Since the fiscal year 2007, a new container terminal (MC-3) with a -20m deep quay capable of handling the increased size of container ships and the diversification of port logistics has been under construction and is nearly completed."

Jan 1, 2015

By Yoshinori Kurumada, Tatsuo Nagatsu, Keiji Uchida

"Cement deep mixing method has been utilized in the process of construction of an underwater tunnel in Singapore. The soil was improved by this method to prevent undesirable heaving of the soil below the excavated area. Quality control experiments approved the effectiveness of CDM method in increasing the strength of the soil and prevention of undesired heave of the ground. The process of the construction of this project and the quality control experiments results are discussed in this paper.INTRODUCTIONThe Marina Coastal Expressway is a 5.3 km long underwater highway tunnel with five lanes in each direction. It mostly comprises a twin box culvert structure (53.3 m exterior width and 10.89 m height) and was opened by the Land Transport Authority of Singapore (LTA).The contract zone C485 was the most challenging area of the construction; it involved a 700 m long underwater tunnel of which 400 m was built beneath the seabed at the mouth of the Singapore River. A double steel pipe sheet pile wall was built as a temporary cofferdam to keep water out of the excavation site, and the cut-and-cover method was used for excavation. In order to ensure a sufficient cross-sectional area for the flow of the Singapore River, the construction was divided into two phases focused on the left bank (Stage 1) and right bank (Stage 2).The Cement Deep Mixing (CDM) method was used to improve the ground, which comprised soft marine clay, to ensure safety during the excavation. The efficiency of this method in increasing the soil’s strength was approved previously. The design standard strength was quck = 800 kPa. Based on the study conducted after the construction, the average the Unconfined Compression Strength (UCS) of the soil stabilized by the CDM method was quf =3,000 kPa. This paper discusses the effect of the CDM soil improvement construction on the reduced displacement from the excavation and the quality control of the soil improvement."

Jan 1, 2015

By Randy McMeekin, Chris Twigge-Molecey, J. Peter Blake

The project implementation phase, FEL4, is generally a complex undertaking. The project has been approved for construction and the capital has been allocated. At this point the project team comes under significant pressure to meet the safety, schedule, cost, and start-up committments. For the design team the principal tasks are to finalize detailed design, complete procurement, and issue construction contracts. Design activities must be closely coordinated with equipment and material procurement. A clear engineering plan should be based on well-defined work packages to meet construction, commissioning, and startup requirements. A range of review processes by discipline, area, and third parties assure quality. Constructability, safety, and hazard reviews are performed throughout the design process. Three-dimensional models that incorporate extensive databases help to maximize efficiency and minimize errors. Well-managed projects have a clearly accountable design team, rigorous change control processes, and well-defined workflows. Key individuals from the design team participate in commissioning, operator training, and startup.

Jan 1, 2015

By J. Oliver, J. Cleason

"With maintenance costs rising and an increasing demand for higher production, the use of sealed spherical roller bearings can reduce maintenance costs while providing increased production uptime. The sealed spherical bearing has increased bearing life by slowing the ingress of contamination. This paper will describe how contamination and bearing wear is reduced by reviewing case histories from coal and metal mines that improved their production by decreasing downtime using sealed spherical roller bearings. INTRODUCTION The spherical roller bearing (SRB) is a robust rolling element bearing that can accommodate high radial loads, low to moderate axial loads, and misalignment with no loss in carrying capacity. (i.e. Figure 1) Because of these characteristics, it is a favorite in mining applications and many other heavy industry applications. Primary applications are the various pulleys on conveyors. Coal and hard rock mines have hundreds of miles of conveyor lines and countless head, tail, drive, and idler pulleys. Maintaining the bearings on these pulleys and replacing bearings that have failed can be a huge expense to a mine in components, labor and downtime. Ideally, the bearings are replaced when the pulley is changed out according to the maintenance cycle, about every 4 years. Reality, however, causes the bearings to be changed out every year, or sooner. These premature bearing replacements can cause production shut downs for as long as 8 hours. Conveyor pulleys have been targeted at many mines as the single biggest maintenance pain point.The primary reason for replacing conveyor bearings is internal wear from fine, solid particle and water ingress through the bearing housing seals. (i.e. Figures 2 & 3) Traditionally, the bearing is mounted in a split pillow block housing (SAF, FSAF, SDAF or SNL are typical industry styles) with only labyrinth seals (LER/LOR) for protection against the ingress of contaminants. The bearings are lubricated with grease. A common way to extend the MTBR is to purge the bearing system with large quantities of grease to flush out the contaminants. If the bearing, and thus the housing seals are not frequently purged with grease, fine solid contaminants enter the housing and bearing through the labyrinth cavities."

Jan 1, 2015

By C. Zangerl, W. Fellin, M. Holzmann, B. Hofer, S. Perzlmaier

"Four deep-seated rockslide systems were investigated and are under surveillance by TIWAG (Tyrolean hydro-electric Company) since the mid-1960s after impoundment of Gepatsch reservoir began. These rockslide systems consist of several individual sliding masses (slabs) which show variable activity from zero to a few centimetres per year. The focus in this paper will be on the findings for the transient deformation behaviour of the Hochmais slab which is part of the “Hochmais-Atemkopf” rockslide system.The rock mass has slid over moraine deposits in the last post-glacial period and was in equilibrium (or slow to extremely slow moving, respectively) until the filling of the reservoir began. During the initial reservoir filling in summer 1964 considerable movements had been observed over a length of 1000 m accompanied with an activation of the Hochmais slab. Geological investigations, additional surface and subsurface measurement showed that the sliding mass is characterized by an en bloc movement and the deformation accumulates within a several metre thick shear zone located within the moraine. In contrast to the deformation characteristics for the first impoundment process (1964 – 1966) where the magnitude of deformation occurred during impoundment, the maximum amount of deformation since 1967 occurs during the drawdown of the reservoir. Based on long term measurement it can be shown that the magnitude of deformations per year correlates with the minimum storage level in the reservoir. Other external influences such as precipitation and snowmelt have no observable impact on the deformation characteristic of the landslide. On the basis of long-term data series it was possible to determine the factors of influence and to elaborate a conceptual mechanical model which describes the transient deformation behaviour of the Hochmais slab induced by the drawdown of the reservoir. The mechanical model considers the reduction of uplift forces in the highly fractured and permeable rock slab during drawdown as well as increasing seepage forces in the less permeable moraine material."

Jan 1, 2015

By D. S. Yang, Y. D. Wang, G. Watanabe, A. P. Notaro

"Deep soil mixing (DSM) walls reinforced with steel soldier piles were installed for excavation support and groundwater control for the construction of a grade separation structure at the intersection of Warren Avenue and the Union Pacific Railroad in Fremont, California to mitigate traffic conditions during the busy commute hours and for the extension of San Francisco Bay Area Rapid Transit (BART) system. Instead of treating the DSM wall as a temporary structure, the reinforced DSM walls were integrated in the design of the permanent structures including retaining walls, and the abutments and pier of the railroad and BART bridges. The integration of steel members inside the DSM wall as part of the permanent structures is an innovation which facilitates the use of top down construction techniques to speed construction and utilizes the steel soldier piles that would have been disregarded after the use as a temporary shoring wall. This paper will review the background of the project and DSM method and present the design and construction of the DSM wall composite structure for this grade separation project.INTRODUCTIONUsing the concept of mixed-in-place piles initiated in the 1950’s in the United States, Japanese contractors in the late 1960’s and early 1970’s installed single mixed-in-place soil-cement piles along a row to create a wall for excavation support and groundwater control. Due to the high groundwater conditions in most of the coastal cities in Japan, wall continuity and uniformity became the requirements of soil-cement walls for reliable groundwater control to minimize ground movement and impacts to adjacent buildings and facilities. In late 1970s, Seiko Kogyo, Co. Ltd. developed the Soil Mix Wall (SMW) method, which uses a triple auger mixing tool to improve the uniformity and continuity of soilcement wall. The SMW method is considered a wall installation method in contrast to the Cement Deep Mixing (CDM) method, also developed in Japan, for ground stabilization in soft soils, especially in the marine environment. In the U.S., generic terms like DMM (Deep Mixing Method), DSM (Deep Soil Mixing) or CDSM (Cement Deep Soil Mixing) are used by various government agencies and private organizations to describe the soil mixing technologies without differentiating the origin, procedure and application. The method used in this project is called DSM method by the project owner, Santa Clara Valley Transportation Authority (VTA), to produce a single continuous soil-cement wall for use as shoring wall and composite structure. The mixing tool for DSM wall installation can vary from 3 to 6 mixing augers. Due to the need to install steel soldier piles into the DSM wall for resisting lateral forces, high water cement ratio slurry with bentonite is used to produce low strength soil-cement, generally in the range of 70 to 100 psi (500 to 690 kPa), with high fluidity to facilitate the installation of steel soldier piles. To maintain the wall continuity for groundwater control, overlapping of one full DSM column is made between neighboring elements using two types of installation procedures as illustrated in Figures 1a and 1b. Steel soldier piles, as shown in Figure 2, are used to reinforce the soil-cement wall to resist the lateral shear force and bending moment induced during the excavation."

Jan 1, 2015

By R. V. Ramani, K. V. Raj

"The air flow problems in open pit mines are complex. Computational fluid dynamics (CFD) models provide a detailed knowledge of the airflow pattern and velocity distribution, temperature, and pollutant concentration within an enclosed domain of the open pit. A range of turbulent model can be selected for varying complexity and accuracy. Pollutant transport models, however, differ in their assumptions and structure as well as in the algorithm they use; as a result, prediction varies from model to model. This paper presents a study of pollutant transport in an actual open pit mine under stable boundary layer. The objective is mainly to test two turbulence models using the same input conditions, model constants, and similar geometry. Measured data are used to compare results of the two CFD models, namely, the kappa-epsilon (?-e) model and the Large Eddy Simulation (LES) model. Despite the complex synoptic situations, different meteorological input data and the fast changing conditions, the simulation results from both the models are in good agreement regarding the dispersion of pollutants.INTRODUCTION Modeling of contaminant transport under Arctic air inversion is an important step for an assessment of the amount of pollutants within the open pit. The Airflow in open pit mines is of larger scale and does not follow the principles of pipe flow. The air flow problems in actual open pit mines are thus far more complex. CFD models provide a detailed knowledge of the airflow pattern and air velocity distribution, temperature, and pollutant concentration within an enclosed domain of an open pit. There is no known application of CFD in three-dimensional modeling of air flow in large open pit mines. Two equation RANS kappa-epsilon (?-e) and Large Eddy Simulation (CFD) models, however, have been developed to solve the stable boundary layer (SBL) problems in Atmospheric Sciences (Baklanov 2000, Basu and Porté-Agel 2006, Dop and Axelsen 2007, Bandopadhyay et al. 2014). Because an exact flow situation in open pit mines is not known a-priori, it is therefore, necessary to investigate various turbulent models to identify the appropriate model that would simulate the flow phenomena with reasonable accuracy, and predict the contaminant distributions within the pit. Dispersion models differ in their assumptions and structures as well as in the algorithm they use and, as a result, predictions vary from model to model. Furthermore, it is also important to investigate the behavior of a CFD model in simulating a complex phenomenon such as the transport and distribution of contaminants in open pit mine under Arctic air inversion. The simulation of an enhanced period of turbulence in SBL is of particular interest because traditional air pollution dispersion models cannot explicitly treat such intermittent events, and yet the SBL is often the worst-case scenario in an open pit pollution transport"

Jan 1, 2015

By Zheng Shuangying

The vibration effect of the buried oil pipeline caused by tunneling blasting affects the pipeline safe transportation, tunnel construction schedule and its construction cost. The dynamic response characteristic of the buried pipeline under blast loads is the foundation of designing blasting scheme as well as the prerequisite to pipeline safety. Taking the blasting engineering of Xiannvyan tunnel passing through a buried oil pipeline of the high-speed railway from Xi’an to Chengdu as the background, according to the space relation between tunnel and pipeline as well as the charge structure of V-cut blasthole, the 3D non-linear dynamic finite element model of tunnel-pipeline was established in the light of the equivalent explosive. The vibration response of the ground surface over pipeline resulting from V-cut blasting was simulated by LS-DYNA finite element program. Comparing with the measured vibration velocity waveforms in site, the accuracy and reliability of the numerical model are well verified. On the base of the simulation method, the coupling dynamic response characteristic between buried oil pipelines and soil was further studied and the Von-Mises stress distribution of pipeline wall was obtained. The safety of buried oil pipeline was quantitatively analyzed through the inside stress data of pipeline given by the simulation calculation above. The analytic results show that the maximum vertical vibration velocity of pipeline on the interface between pipeline and soil is 1.62~5.07 times as large as that of soil. When the buried pipeline is located over the tunnel and 13 m (42.6 ft) away from tunnel, the maximum vertical vibration velocity of ground surface caused by V-cut blasting with charge weight 17 kg (28.6 lb) is 3.17cm/s (1.25 in/s) and the vertical peak vibration velocity of pipeline top is about four times as the ground location directly above the pipeline. Meanwhile, the peak dynamic stress of the buried pipeline caused by blasting vibration is only 2.35% of the allowable stress of steel pipeline. The maximum superimposed stress of the blasting dynamic stress and the hoop stress produced by the pipeline internal pressure is 242.56 MPa (35 180.36), which implies that the buried oil pipeline is completely safe under the conditions of the given tunnel blasting scheme.

Jan 1, 2015

By G. Song

"SynopsisAccording to the overlying rock strength and thickness of 10 shallow coal seams in China, the strata are classified into four types: weak and laminated strata (hereinafter referred to as WL), weak and massive strata (WM), strong and laminated strata (SL), and strong and massive strata (SM). The four types of strata, together with longwall panel height (M), panel length (L), and seam depth (H) are factors that influence the loads on hydraulic power supports. Principal component analysis was used to study the seven influencing factors. It turns out that seam depth (H) is multicollinear with WL, WM, SL, and SM. Thus the enumerated seven factors are divided into two models. In Model 1, six factors; panel height, panel length, and layer thickness of the four type strata are involved. In Model 2, three factors; panel height, panel length, and seam depth are included. Using multivariate regression analysis, two equations to calculate loads on supports are obtained for each model. The equations were applied to shallow coal seams. The equation of Model 1 is more accurate than that of Model 2, but Model 2 could be further used in deep coal seams. The equations were coded through VB programming to simplify the calculation.IntroductionTo ensure coal production in the long term, the focus of coal mining has been gradually shifted to the western areas of China in recent years due to rich coal resources in this region. Most of the coal seams in this area are shallow but the support loads are abnormally high. In these circumstances, the chock loads estimating methods used in the past do not work. If the rated working resistance of a support is larger than needed, the shield is unable to fully perform, while a lower working resistance would lead to accidents like shield crushing or even casualties. This problem is frequently found in shallow coal seams such as Shenfu-Dongsheng, Yulin, Tuha, Lingwu etc. (Zhang, 2011). Thus, to ensure safety and efficiency during mining, the estimation of support loads and selection of supports are of great significance."

Jan 1, 2015