Search Documents

By Donald Deardorff

"Helical piles often rely on the final installation torque for ultimate capacity verification. When helical piles are designed using traditional bearing capacity equations for deep foundations and field monitored for a specified final installation torque, a factor of safety equal to 2 is often allowed for the design. One of the more common methods of determining torque during helical pile installation is by correlating the differential pressure across a hydraulic gear motor to a torque. Most drive head manufacturers provide multipliers to convert differential pressure to torque for different drive head models. These multipliers are based on theoretical torque equations and vary with the planetary gear ratio, hydraulic gear motor displacement and drive head efficiency. Drive head manufacturers show a linear fit between the differential pressure and output torque with no scaling effect. Previous drive head testing performed by the author has confirmed that the drive head differential pressure to torque relationship is generally linear however there is a scaling adjustment needed. This results in a variation of multipliers across the differential pressure range for a given drive head.Eight hydraulic drive heads from three manufacturers were field tested by Foundation Supportworks, Inc. to compare the torque versus differential pressure curves with varying installation equipment, hydraulic line sizes and hydraulic flow rates. Differential pressure was monitored using three methods including pressure gages, PT-Tracker and an Ashcroft AT-100. Flow and temperature was measured using a Webtech system analyzer. Torque was measured using a Pro-Dig in-line torque transducer, a TruTorque indicator and a Chance Mechanical Dial in-line torque indicator. The current testing indicates that a change in installation equipment and/or a change in hydraulic flow rate may affect the torque versus differential pressure curve of a given drive head. The results of this testing also show that some of the methods for determining torque during helical pile installations may be unconservative, thereby resulting in safety factors less than required."

Jan 1, 2017

By Steven M. Henderson, Zachary D. Jones

The risk of allocation in construction contracts is a primary concern for all parties. For contracts involving subsurface construction the allocation of site condition risk is critical. In the past one hundred years technological advances fundamentally changed how that risk is allocated; yet another shift in this risk allocation may lie just over the horizon due to advances in geotechnical data management. Around the world initiatives are underway to make geotechnical datasets more open and accessible. In the United States some states like Kentucky have already made geotechnical data readily accessible. This proliferation of geotechnical data in the U.S. may impact the allocation of subsurface risk in construction contracts. Many construction contracts contain a differing site condition clause. That clause allows for a modification of the contract price or schedule if the ground conditions encountered by the contractor differ materially from either what was indicated in the contract documents or would be reasonably expected. A contractor, however, is typically not entitled to that modification if the contractor knew or should have known of the adverse conditions encountered. Courts have interpreted the “should have known” language as requiring contractors to make a reasonable site investigation prior to bidding the project. If geotechnical data is available and accessible and reveals the adverse condition the contractor encounters, courts could find that the contractor should have known of the condition and thus will not be entitled to a modification based on the differing site condition clause. Accordingly, the U.S. could be on the threshold of significant shifts in how the risk of differing site conditions is allocated in construction contracts.

Jan 1, 2017

By Charles M. Wilk

"Mass stabilization involves mixing binding agents into marginal or contaminated soil to improve the subject material’s physical and/or chemical properties. This paper concentrates on the principles of soil mixing and benefits and application to new and existing rail right-of-way. Successfully applied in Scandinavia and other European countries, the soil mixing is now being applied in right of way in the northern latitudes of the U.S. and Canada. These regions have significant areas of “peaty” soils that can complicate construction and maintenance of rail and structure foundations. Mass stabilization can be used to improve the bearing strength of these soft soils for subsequent construction of railroads, pipelines, roads, and buildings. In civil engineering, the technology is often used to improve the construction properties such as bearing strength, of a marginal soil. In environmental engineering, stabilization is remediation treatment technology that protects human health and the environment by immobilizing hazardous constituents within the treated material. . The treatment is conducted while the subject material remains in-place (insitu). Mass Stabilization is often used to accomplish both civil and environmental purposes on the same project effectively addressing marginal soil while eliminating the expense of soil removal and replacement.This paper presents the principles of mass stabilization technology, implementation in the field and recent completed railway projects.The example rail projects will present the various benefits that soil mixing provides to railway construction and maintenance. Bench-scale studies and full scale implementation as well as soil construction properties before and after mass stabilization will be discussed. The paper and presentation will include information on the advantages of mixing methods and binding agent delivery systems.INTRODUCTIONNew or existing railroad right-of-ways may cross ground with low bearing capacity. Right of way subgrade undergo deflection (strain) as loads (stress) are applied (1). The amount of strain or deflection of the subgrade caused by loading of a train is proportional to the stiffness of the subgrade materials. Some soils, such as tamped ballast, are very stiff and resist loads well. Other soils such as soft clay, peat, or loose sand have low stiffness and undergo substantial movement under loads. It is very desirable to have the stiffest possible material in a track subgrade. Stiff subgrade material limits deflection under load, reducing track roughness and occurrence of track defects. Mass stabilization is a geotechnical method that can be used to improve the bearing capacity or stiffness of soil in these right-of-way. Mass stabilization involves mixing binding agents into soil subject to treatment while the soil remains in-place or insitu. Variations in the design or areas subject to treatment can be used to address transmission of vibration to adjacent structures."

Jan 1, 2017

By Pingchao Ke, Zhihong Liu

Fe(III)-As(V) precipitates were synthesized from the Fe(II)-As(V)-SO42--H2O system at 90°C in initial Fe(II)/As(V) molar ratios of 4.0 and 5.0, respectively. The synthesis were carried out by introducing oxygen gas into the system to oxidize Fe(II) ions into Fe (III) ions, and at the same time, adding aqueous sodium carbonate solution into the system to neutralize the acid released by the hydrolysis reactions, with the purpose of keeping the pH constant at 1.5±0.05. The precipitates obtained were characterized by XRD, chemical composition analysis, SEM, XPS, and Raman spectrum. The results indicated that the particles in the precipitates were in the morphology of irregular aggregation with their sizes in the range of about 1–4 µm. The precipitates consisted of scorodite, ferric arsenate and amorphous hydrated ferric oxide, of which amorphous hydrated ferric oxide formulated as Fe(OH)x(SO42-)y. The characteristic XPS peaks of Fe-AsO43- and Fe-O in the precipitates located at 711.8 and 713.3 eV, separately, and the existence of amorphous hydrated ferric oxide led to two series of shake off lines developed over the end of high binding energy of Fe2p XPS. The precipitates were stable in TCLP tests at pH 4.93 for 60 hours with the arsenic concentrations in the leaching solutions being 0.27 mg/L and 0.59 mg/L for the precipitates prepared in the initial Fe(II)/As(V) molar ratios of 4.0 and 5.0, respectively. The tests for the long-term stability of the precipitates were carried out by leaching them for 40 days at 25°C under various media in the pH range from 9.50 to 10.57, and the results showed that the precipitates synthesized in this study were much more stable than those by previous researchers.

Jan 1, 2017

By C. Vipulanandan, M. Dawood, Dongmei Pan

"With the aging infrastructure, there is a need to maintain and extend the service life of steel structures in general and steel piles in particular. Steel piles support not only vertical loads but also dynamic horizontal loads in onshore and offshore applications. In order to select the appropriate methods to repair corroded steel piles used in onshore and offshore application, corrosion mechanisms were investigated with the rate of corrosion in various environments. The corrosion rate of steel in soil, water and soil-water interface varied from 2 to 500 µm/year. Based on literature review and analyses, the repair methods can be broadly characterized as protective coating, electro-chemical methods, wrapping and encasement and partial replacement of steel. Also, methods to evaluate the repair materials and the repair configuration have been documented.IntroductionOne of the biggest challenges facing the aging infrastructure is the materials loss and deterioration due to corrosion. Many studies indicate that in the US alone, costs due to corrosion loss is more than $276 billion annually (Michiel et al., 2010). Corrosion is the major cause of deterioration of steel structures and components (MNC, 2005). Load bearing steel piles are used as foundations for various types of structures and hence corrosion is very much influenced by the environment such as soil, water and soil-water interface. Corrosion of steel pile foundations may result in reduced capacity in the axial and lateral directions. Hence, understanding the rate of pile corrosion is essential to select the appropriate repair methods to avoid excessive deflection and failure (Decker et al. 2008).To prevent the deterioration mechanisms that attack a pile, it is fundamental both to identify and understand the deterioration mechanism that has been the cause of damage. Understanding the deterioration mechanism allows the engineer to design a repair that will combat this type of damage. It is widely recognized that the corrosion of carbon steel in soil, water and soil-water interface proceeds according to the following simplified anodic reaction and cathodic reactions in the presence of oxygen (Decker et al. 2008)."

Jan 1, 2017

By Nuno Cruz

"The concrete overbreak estimation for bored piles provides the quantification of the shaft’s expansion beyond its theoretical volume. There are stability analysis methods that can be employed before and after concrete pour but as for the moment of decision, during pile cast, the most common method still consists in measuring the rising of the concrete level in order to compare its poured volume with the theoretical pile section volume. This is a determinant parameter to monitor, not only because it assesses the bored shaft stability but also because it represents a direct cost. When analyzing the estimation methods commonly applied on-site it becomes evident that these are often affected by human errors that lead to misleading results. The objective of this paper is to identify those errors and discuss a subject which is usually overlooked. As a general conclusion, it was ascertained that most errors derive from inaccurate volumetric data, working procedures and gauging equipment. By acknowledging these widespread practices deep foundations contractors will be in a better position to make informed decisions on how to correct and improve bored pile stability.GENERALBackgroundWhen executing bored piles, the estimation of its concrete overbreak allows a swift appraisal of the excavation stability during the drilling process. This is simply obtained from the proportion of the poured volume of concrete over the drilled shaft theoretical volume, as shown in equation [1].Where CO = concrete overbreak percentage, Vc = volume of poured concrete, Vr = pile’s theoretical volume. This calculation not only provides a general idea of the shaft’s expansion from its theoretical volume, but also the outline of the excavated column’s geometry. For the latter, the outline will be as accurate as the number of measurements taken for each partial known volume of poured concrete. This means that for each load placed inside the excavation there is a corresponding rising of the concrete level. The profile of the definite pile is then plotted (see Fig. 1) and allows inferring about how stable remained the shaft walls up to the moment of casting.The technological developments in this area have provided other methods for determining pile stability before and after pile cast, such as ultrasonic echo sensing, cross-hole sonic logging or thermal integrity profiling systems. Notwithstanding, concrete overbreak assessment remains as common practice and confers the advantage of providing stability information during the process of pile casting."

Jan 1, 2017

By T. J. Morris

"From November 2014 through September 2016, Westmoreland’s Coal Valley Mine utilized a Marion 7450 electric walking dragline to extract 1.2 million tonnes of a vertically-dipping, 52-meter wide, fault-thickened seam, beneath a conventionally-excavated pit bottom. Mine planning and operational hurdles encountered throughout a kilometer of mined strike length included mitigating highwall instability in both hanging and footwall slopes, water management, and end-of-life machine reliability and maintenance. The most substantial challenge has been the depressed global coal market. However, the successful application of this mining method significantly aided the overall cost of production at the site. The valuable experience gained from this project will be extended to future mining areas where this technique can be similarly applied. INTRODUCTION Coal Valley Mine is located approximately 220 kilometers southwest of Edmonton, Alberta, Canada, in the foothills of the Rocky Mountains. Since commercial production began in 1978, more than 84 million clean tonnes of coal has been produced and sold domestically as well as exported overseas for power generation. While the existing processing plant has a nameplate capacity of 4 million tonnes per year, the site has operated at a 2 million tonne rate since 2015 due to depressed export markets. Westmoreland acquired the mine as part of its purchase of Sherritt Coal Operations in April 2014. The mine operates 24 hours a day, 7 days a week, with an IUOE workforce of 261. GEOLOGICAL SETTING The geology of the Yellowhead Tower mining area differs significantly from previous mining areas at Coal Valley. The Mynheer coal seam discussed herein consists of steeply dipping, highly-sheared, thrust-faulted, and heterogeneous coal pods. Deep set, southwest striking thrust faults were the likely mechanism for the podding and have resulted in overturned, rolled and highly sheared seams with zone thicknesses of up to 65 meters.The hanging wall is characterized by soft bentonitic mudstones and siltstones, overlain by massive competent sandstone. The footwall is defined by a hard volcanic tuff, interbedded with thin, sporadic coal seams. The sandstone above and volcanic tuff below constrained the faulting system within this zone, enabling the mass podding that has afforded the opportunity for large-scale mining."

Jan 1, 2017

By Mario Mauro, Jeff Taylor, Carlos Morales

"In 2007 the US Army Corps of Engineers classified the Herbert Hoover Dike in Florida as a Dam Safety Action Classification (DSAC) 1 dam, and started the implementation of one of the largest dam rehabilitation projects in the nation. The construction of the cutoff wall is a key feature of this rehabilitation work to upgrade the dike to current dam safety criteria. The cutoff wall installation is currently being completed on Reach 1, which extends from Port Mayaca to Belle Glade, under a Multiple Task Order Contract based on performance specifications and stringent verification criteria.For the construction of the cutoff wall TREVIICOS selected the self-hardening slurry method. Since the cutoff wall is installed through a layer of highly variable limestone with Unconfined Compressive Strength (UCS) up to 14,000 psi, the excavation requires the use of the hydromill equipment. This is the first successful application of the hydromill technology with self-hardening slurry in a large scale project in the US. This paper presents the details of the method utilized, the quality control procedures, and the experience gained over seven miles of cutoff wall installed.INTRODUCTIONProject LocationThe Herbert Hoover Dike (HHD) system, around Lake Okeechobee in South Florida, consists of a series of levees, culverts and locks and is approximately 143 miles long (Figure 1).Lake Okeechobee is the second largest freshwater lake in the lower 48 states of the United States. The lake is the primary drinking water source for numerous communities around the lake and to millions of people living along the lower east coast. The lake is also a vital source of irrigation for the agricultural industry in the South Florida region.Lake Okeechobee is 33 miles wide from north to south and 30 miles wide from east to west and has a surface area of 730 square miles. The average water depth of the lake is 9 ft."

Jan 1, 2017

By M. Paricheh, M. Rahmanpour

"The cost efficiency and high reliability of semi-mobile or combined in-pit crushing-conveying (IPCC) and truck systems, compared to conventional truck-shovel systems alone, make them more attractive for use in modern mining operations. Semi-mobile systems, which are the most common systems in open-pit mining, combine the advantages of both systems such that fewer trucks are required, operating costs are lowered, and the operation is environmentally sound. One major aspect of utilizing this system is determining the location of the in-pit crusher and the timing of relocations. Facility location models are rarely used in the mining sector, but these models may be used for solving the in-pit crusher location problem. To this end, the main parameters affecting the IPCC location in open pit mines are reviewed and examples given of how they are applied to a dynamic location-relocation problem. Subsequently, the model is implemented for Sungun copper mine in Iran and the number and the exact time of relocations of the IPCC units determined. IntroductionNowadays, compared to the last century, metal prices are more volatile, average and cut-off grades have decreased, and stripping ratios increased. From a mining engineering point of view, many ore deposits with simple access and low capital and operating costs have been exhausted. The remaining deposits are located at depth, with no easy access, which requires high initial capital costs (Osanloo, 2012). Mining at great depths and high tonnages is possible only through open pit mining. Today, more than 80% of open pit mines in the world use a shovel-truck system for loading-hauling operations (Osanloo, 2010).With increasing depth, haulage distances increase and the number of loads per truck decreases. As a result, fuel, tyre, and depreciation costs per ton increase. Owing to these factors, open pit mining at great depth (300 to 1000 m) using shovel-truck systems faces some technical and economic problems. In-pit crushing-conveying (IPCC) systems have been known in the mining industry for many decades. The idea was introduced in 1956 in Germany. Today, the cost efficiency and high reliability of IPCC make it more appealing than conventional shovel-truck operation, especially in longer life projects with lengthy transportation distances and high production rates (Koehler, 2003). Since 1956, different aspects of this system have been reviewed by many researchers. Barua and Lanergan (1985) developed a computer program that compares the tonnage aspects of various conveyor layouts. They believed that to maximize the economic benefit of lower haulage costs associated with in-pit conveying, one must first minimize the cost of the flatter slope, which is expressed in terms of additional stripping or tied-up ore. Dos Santos and Stanisic (1987) evaluated the design of a high-angle conveyor at the Majdanpek copper mine. Then, Sturgul (1987) applied GPSS (general purpose simulation system) to find the best location of an in-pit crusher."

Jan 1, 2017

By A. E. M. Warner, A. Vahed, P. J. Mackey

"Since early 2015, the price of nickel has dropped from the region of US$6/pound to current levels of around US$4.60/pound (March 2017), reflecting several market factors, but principally due to lower demand from China. Under such conditions, nickel companies have been under pressure to contain operating costs. In addition, labor and energy costs will continue to rise, while nickel ore grades will likely continue to drop. All major companies now accept the need for climate change action and consequently efforts are being made towards lowering carbon-based emissions. Nevertheless, meeting these challenges can also contribute to higher operating costs without parallel innovative developments - which at the same time, under current conditions, major companies are tending to curtail. In this paper, several productivity improvement opportunities to reduce unit operating costs at nickel sulphide and nickel laterite plants are reviewed. Opportunities include: (a) process technology and energy-type selection, production capability, optimization of process intensity and implementation of newer technologies; (b) improved productivity, equipment availability including maintenance best practice; (c) energy savings and recovery opportunities and use of energy surveys and, (d) process modeling and improved scheduling. Such improvements along with an uptick seen in nickel demand going forward should better position the world nickel industry.INTRODUCTION Nickel is an essential metal to modern society, primarily through its use as an important ingredient in stainless steel. Thus, stainless steel finds vital applications in food preparation facilities, as well as important uses in transportation and industrial applications. Canada has always played an important role in nickel production and nickel metallurgy. In the 1940s and 1950s, Canada supplied over 90% of the world’s nickel. However, this proportion has declined considerably to around 10% of the world nickel supply today. Still, Canada remains an important nickel supplier and contributor to nickel extractive technology. Due to the importance of nickel to society, nickel demand is expected to continually rise. On the other hand, nickel companies have been under pressure to contain production costs amid languishing nickel prices. While demand projections show nickel growth, there are uncertainties in actual levels of future market growth. Ore grades are dropping, while labour and energy costs, which are key cost contributors are rising, hence efforts to lower production costs will generally require innovative approaches."

Jan 1, 2017

By Ihsan B. Tulu, David F. Gearhart, Gabriel S. Esterhuizen

"Ground deformation and support response was monitored in a longwall gateroad as part of a research project into gateroad stability under changing loading conditions. In this study, instrumentation was installed in a gateroad located between two active longwall panels. The first panel to pass was the second panel in the district, and the second panel to pass the instrumentation sites was the third panel in the district. All of the panels in the district were right-handed. All of the instrumentation was installed in the number one entry, the tailgate, the second panel to pass the instrumentation sites at a mid-pillar location, and at an outby intersection location under about 600 feet of cover. The instrumentation included roof extensometers, cable bolt load cells, hollow inclusion cells, borehole pressure cells, standing support load cells, and convergence sensors, and a multipoint borehole extensometer. The roof extensometers measured roof convergence and sag. The cable bolt load cells measured the roof load applied to the cable bolts in the secondary support array. Hollow inclusion cells measured the magnitude and direction of the principal and shear stresses. The borehole pressure cells measured the stress on a pillar in the entry nearest to the second panel to pass the instrument site. The instrumented wood cribs in the entry nearest the second panel recorded the closure and load on the cribs, and the multipoint borehole extensometer in a pillar closest to the second panel recorded the location and width of cracks that occurred and total expansion of the pillar. This paper describes the effects of the changing stress caused by the first panel as it approached and passed the locations of the instruments on the opposite side of the gateroad system and the later effect caused by the second panel as it approached and passed the mid-pillar instrument location. The first panel passing caused significant loading at the mid-pillar instrument location, but not at the intersection location, while the second panel had passed the mid-pillar location and just arrived at the intersection location when the dataloggers needed to be removed."

Jan 1, 2017

By Elizabeth Edwards, Radhakrishnan Mahadevan, Vladimiros G. Papangelakis, Srinath Garg, Kurtis Judd

Mineralogical characterization of the tailings showed the deportment of Ni to be similar in the Vale and Glencore tailings, with 60% of the total Ni locked in pyrrhotite, and the balance 40% associated with pentlandite. The overall Ni dissolution was correlated with the individual dissolution extents of pyrrhotite and pentlandite as functions of four leaching regimes: ‘anoxic acid’ (with and without pH control), ‘oxic acid’ (oxygen sparging), ‘oxic acid’ (air sparging), and ‘oxic ferric’ (air sparging). The results showed that the maximum Ni dissolution was obtained during the pH controlled oxic acid leach with oxygen sparging at pH 1.5, while the anoxic acid leach at pH 1.5 resulted in minimum Ni dissolution (10–15%) from pyrrhotite. An overall Ni mass balance showed that pyrrhotite and pentlandite dissolve simultaneously in the presence of Fe(III) and oxygen, in contrast to the preferential dissolution of pyrrhotite in the absence of Fe(III). Sulphur mass balances revealed that the yield of elemental sulphur is maximized (65%) during the oxic Fe(III) leach at pH 0.6. Furthermore, the kinetics of Ni leaching and elemental sulphur formation from pyrrhotite tailings leached with ferric sulphate between 55–80°C was investigated at constant oxidation-reduction potential. Elemental sulphur yield increased with increasing temperature, but no observable trend could be linked to ferric or ferrous ion concentration.

Jan 1, 2017

By Juan M. Pestana-Nascimento, Robert G. Bea, Hamed Hamedifar, Emery M. Roe

The current State-of-the-Practice is grounded heavily on deterministic characterization and assessment of the performance of civil engineering infrastructure. In particular, flood defense systems, such as levees, have been evaluated within the context of the Factor-of-Safety where the computed capacity of the system is compared with the code specified demand forces. Uncertainties associated with the capacity and demand forces render deterministic modeling incomplete. In particular, two structures with the same Factor of Safety can have vastly different probabilities of failure. While efforts have been made to assess levee vulnerability, results from traditional engineering approaches omit important factors because they do not account for uncertainties included in analytical modeling, and natural variabilities, or human and organization factors. This paper utilizes risk assessment methods to advance methods for quantifying the contribution of uncertainties to engineering analyses, and thereby provide additional information to help assess sustainability of geotechnically engineered systems. The probability of failure of a geotechnically engineered system is directly impacted by how well the system is understood, and how uncertainties are incorporated in development of understanding of the system. This paper presents methods to evaluate two types of uncertainties for three potential failure modes of flood protection levees: underseepage, slope (or levee) instability, and overtopping/erosion. These analyses account for two types of uncertainty: 1) Type I – inherent uncertainty, 2) Type II – analytical modeling uncertainty. Human and organizational task performance and information development and utilization uncertainties are not included in these analyses. This paper focuses on the behavior of the flood protection levee system for Sherman Island, a western island in California’s Delta. Sherman Island is of critical importance to California because of the very important infrastructure systems that pass under, on, over, and adjacent to Sherman Island, including: natural gas pipelines, regional and interregional electricity transmission lines and telecommunication facilities, two deepwater shipping channels; and State Highway 160, a link between major transportation expressways. The work evaluates current (year 2010) and future conditions (year 2100) and incorporates variations in capacity and demand arising from projected human response activities and global climate change.

Jan 1, 2017

By M. J. Bunyard, I. Mullany

"The pressures on mine operators are varied and constantly increasing, declining ore grades, more remote locations and increasing environmental concerns. The challenge facing the mining industry is to find new ways to process ores which are more efficient and less costly and to control them better. This requires a fundamental rethink in the way in which projects are developed, it is no longer good enough to just copy what has been done before. The process starts with the surfacing of the primary underlying constraints for the project and the establishment of new design principles to address these. The generation of new design criteria and processing options follows the well-established path of brainstorm, focus, brainstorm, refocus and economic evaluation. The aim is process intensification, doing more with less, as early as possible and better use of plant data. The methodology requires a complete geometallurgical understanding of the orebody to facilitate the evaluation of viable processing options. Examples of early stage processing considered are blast optimization and ore sorting to reject waste and reduce processing costs. Mine to mill integration, which starts with the optimization of blasting for separation, offers another way to significantly reduce operating costs and increase efficiencies.VALUE MODEL The mining industry has, over the past decade, experienced an unprecedented cycle of increased commodity prices and investments in new mining and processing capacity followed by a market collapse and fall in prices and confidence. Whilst there are now some signs of a return to investment in new capacity, the metals and mining industry is still wrestling with eroding margins and investor demand that companies achieve the full value of their assets. Metals and mining companies must work on all available levers to deflate their costs back to more manageable levels and capture the full value for their products. Levers include optimizing external spending, re-thinking make vs buy trade-offs, debottlenecking, improving availability and operating time of key equipment, more accurate and agile planning processes, value-in-use optimization, and tighter performance management. Figure 1 is a diagrammatic representation of a company’s value model. The three goals of a successful mining enterprise are social acceptance, environmental acceptance and sound financial returns to shareholders. Some of the KPI’s used to measure the success or not of achieving these goals are shown in the translation layer."

Jan 1, 2017

By William Gleason

"The times they are a changing, and, for the mining industry, the optimism is high. On Nov. 8, Donald Trump was elected as the 45th president of the United States, and the Republican Party won a majority of seats in the U.S. Senate and the House of Representatives, ushering in what many hope will be a positive change for the mining and extractive minerals industries.Trump has stated that one of his top priorities as president will be to increase spending on the nation’s infrastructure, which could help spark a boom for mining. He has also pledged to bring back coal jobs and reverse many of the environmental regulations that were put in place by the Obama administration. However, before the mining industry gets too far ahead of itself and plans for another Super Cycle, there are stark reminders that any work in the natural resources sector is complicated and challenging. On Dec. 4, the U.S. Army Corps of Engineers announced that it would not grant an easement that would allow the Dakota Access Pipeline to pass under a portion of the Missouri River in North Dakota. The proposed crossing of the oil pipeline is approximately a half a mile upstream from the Standing Rock Sioux’s Reservation, and for months, hundreds of protestors camped out at the site in an effort to halt the project, saying they feared how it would impact water supplies and sacred lands.Energy Transfer Partners, the company building the pipeline, said the pipeline is a $3.78-billion investment that will connect the Bakken and Three Forks production areas to major refining markets. The company signed voluntary easement agreements with landowners representing more than 85 percent of the properties along the four-state route but faced an organized protest from the Sioux Nation at Standing Rock. The protest gathered momentum and support through social and traditional media and became the focal point of global environmental and indigenous activism. The protestors claimed victory, at least temporarily, when the Corps of Engineers said it would look for alternative routes for the project. It’s a decision that could lead to a lengthy environmental review and one that has the potential to block the construction of the pipeline for months or even years."

Jan 1, 2017

By K. Lillkung, J. Kourunen, M. Latva-Kokko

"Carbon-in-leach (CIL) and carbon-in-pulp (CIP) processes utilize activated carbon to adsorb solubilized gold for recovery. Due to carbon attrition and non-ideal carbon management, however, some of the gold is lost in carbon fines and to the solution. The carbon attrition mechanism inside CIL/CIP reactors is mainly abrasion-related. This is critical to gold loss since gold loading takes place predominantly in the outer shell of the carbon particles. Thus fine carbon dust has a relatively high gold content and such a small particle size that it cannot be captured with safety screens. The attrition rate depends on ore and carbon characteristics, but it is always proportional to the mixing power intensity. This rate can be minimized by continuous suspension level measurement and control of agitation speed. In addition, a novel tank bottom structure can significantly reduce the required mixing power input compared to a flat bottom tank. A major challenge in carbon management is infrequent and inaccurate measurement of carbon concentration in the reactors. In order to reduce soluble gold losses by means of improved carbon management, Outotec has been developing a continuous in-situ measurement for carbon concentration that is tolerant to changes in slurry density.INTRODUCTION Cyanide leaching has been utilized since the late 19th century as a standard technology for hydrometallurgical gold production. Since then, gold and silver recovery rates have increased due to technological development, but very similar recovery methods are still being used. The original recovery method was to use zinc precipitation – similar to the Merrill-Crowe process, which is still common for feed materials with low throughput and high silver content. However, in most cases, activated carbon recovery is preferred due to its improved efficiency. The carbon-in-pulp process (CIP) and its modification, carbon-in-leach (CIL), have a lower residual soluble gold level and are not similarly affected by soluble base metals. The main alternative for the use of carbon is ion exchange resins. The principle of resin processes is similar to the CIL/CIP processes, with a different type of adsorbent material. Carbon processes are usually preferred over resin processes due to the significantly higher cost of resin material and the possibility to use simpler, well-established technology with carbon processes."

Jan 1, 2017

By R. Agius, A. Nacu

"Adoption of the International Cyanide Management Code, regulatory requirements and community concerns have increased the need to implement suitable cyanide destruction processes at gold operations to meet ever more stringent discharge limits. As standards set for the allowable concentrations of cyanide, cyanide compounds and other contaminants may vary from country to country, jurisdiction to jurisdiction, and even from site to site, there is no “one size fits all” technological solution. Currently the most common cyanide destruction processes used in industry are sulfur dioxide/oxygen, hydrogen peroxide and Caro’s acid. Regardless of the process used, cyanide destruction plants must be reliable and achieve permit guidelines at all times. The selection of the most appropriate cyanide destruction process for an operation depends on several factors, including permit discharge requirements, tailings chemistry, location, site-specific climatic conditions and size of the operation. Only after considering all these factors together can the most effective approach be selected to achieve the permit guidelines economically and technically feasible. Finally performing the correct test work program is the most important step to ensure that the correct process design criteria can be determined to accurately calculate capital and operating costs.IntroductionThe adoption of the International Cyanide Management Code in 2005, stricter regulatory requirements and community concerns prompted by environmental incidents involving cyanide have increased the need to implement cyanide destruction processes at gold and silver operations.Process solutions associated with the extraction of gold and silver contain several forms of cyanide. The most toxic form of cyanide is free cyanide, which can be present as a dissociated cyanide anion (CN-) or gaseous or aqueous HCN. Weak or moderately stable cyanide complexes such as those of zinc, copper and nickel are classified as weak acid dissociable (CNWAD). Although less toxic than free cyanide, weak acid dissociable cyanide complexes are considered “ecologically sensitive” forms of cyanide and are regulated in most jurisdictions. In practice, reported WAD cyanide values are comprised of both free cyanide and weak acid dissociable cyanide complexes. Cyanide complexes with gold, mercury, cobalt and iron are referred to as strong acid dissociable complexes (CNSAD) and are much more stable even under mildly acidic conditions. Another term commonly used in cyanide chemistry is total cyanide, which represents all cyanide compounds present in solution, with the exception of cobalt complexes. Total cyanide levels in solutions are in most cases higher than WAD cyanide values and the difference between the two usually indicates the presence of iron-cyanide compounds. Typically, in Canada CNTOTAL levels cannot exceed 1 mg/L in solutions."

Jan 1, 2017

By Federico Pagliacci

"Many existing dams are subject to underwater seepage due to subsoil conditions, like deep alluvial deposits or pervious rocks or karst. Remedial works are necessary in order to install new cut-off walls to stop the water flow. In some cases the cut-off walls have to be executed at depths never reached so far, and difficult to reach with traditional foundation techniques. In many cases the Hydromill technology proved to be the best system to overpass rocky layers and ensure the required verticality. The maximum depth reached by the industry was in the range of 120-150 meters. This article describes the test performed to excavate and cast in place a 3.2x1.5 m panel to a depth of 250 m. The article will also describe the stratigraphy of the site down to 250 meters, as well as the technique adopted to achieve the said depth with deviations from verticality of 30 cm along the longitudinal axis (0.12%) and 20 cm along the transverse axis (0.10%), measured at the bottom of the excavation. The concreting of the panel, for about 1,100 m³, with plastic concrete in the lower portion and conventional concrete in the upper portion will be illustrated. Finally, the tests performed during the excavation and after concrete casting will be also described, with special attention to the continuous directional core drilling that was performed along the whole length of the panel to verify the results of the deviation from verticality, through the onboard instruments, and to control the quality of concrete at a depth never reached before. IntroductionMany existing dams are subject to underwater seepage due to subsoil conditions, like deep alluvial deposits or caves and cavities or acid solutions in the bedrock formations.Conventional remedial works generally consist in the construction of an additional cut-off wall throughout the dam body and the subsoil, in most cases being deeper than the original one. Today, many examples of successful remedial cut-off walls allow the engineers to design the most suitable solution according to the dam and subsoil characteristics and nature.The real difficulty stems from the depth at which the new cut-off wall has to be socketed in competent rock or soil, so as to eliminate underwater seepage. The maximum depth ever achieved with a cut-off wall is 122.5 m for the remedial work of Mud Mountain Dam, Washington, USA, in 1988-1990. This 0.85-1.0 m thick cut-off wall was realized by means of a Hydromill, by excavating single 2.8 m-wide secant panels."

Jan 1, 2017

By Hongwei Wang, Hao Zhang, Panshi Xie, Xicai Gao, Youfu Zeng, Yongping Wu, Juan Dou

"The reserves and production of steep coal seams account for approximately 15–20% of the total coal reserves in China and 5–10% of the total annual coal production. More than 50% of the coal is high-quality coking coal and anthracite, based on reviews of steeply dipping seam mining at home and abroad. Fully mechanized mining is considered to be the only safe and efficient way to mine steeply dipping seams. To achieve fully mechanized longwall mining, four issues must be addressed: ground control, equipment stability control, development of complete sets of equipment, and safety. Engineers must focus on many factors of steeply dipping seams, such as the following: stope, roof asymmetrical structure, stability control, “roof-support-floor” system dynamics control, multi-region big-range ground control technology, adjustment false-inclined method, nonlinear layout method, control technology, safety, and development of complete sets of equipment. Engineering practices in China introduce these concepts systematically: fully mechanized mining of medium-thickness seams, fully mechanized high mining of thick seams, fully mechanized caving of extremely thick coal seams, fully mechanized mining of coal seams, roadway support, and so on. A steeply dipping seam is one with a dipping angle in the range of 35°–55°. This accounts for about 15%–20% of the total coal reserves in China. Because of the environment, more than 50% of the coal is high-quality coking coal and anthracite. Mining steeply dipping coal seams is known to be difficult in the mining industry. After the study conducted by Germany, Poland, and the former Soviet Union in the1970s–1980s, the fully mechanized mining basic theory, core technology, and key equipment research have not been a breakthrough. Being fully mechanized is a technological “restricted area” at home and abroad. A lot of steeply dipping seams are excavated by non-mechanized mining, leading to harsh job environments, labor-intensive work, low productivity, frequent accidents, and significant security hazards. The death rate per million tons of coal reaches above 4.0 and is far higher than slow inclined coal seam mining. Making steeply dipping seam mining safe and efficient is a global problem that urgently needs to be solved. Fully mechanized mining is the only way to overcome these problems (Wu, 2003; Wu, Yun, and Zhou, 2000). The realization of fully mechanized coal seam mining must solve four problems. (1) Examine the disaster mechanisms induced by overburden “key strata” mutation under steeply dipping seams as a basis for ground control methods and technical problems. (2) Work to solve the dynamic stability control technical problems of thousands of tons of complete sets of equipment under the steeply dipping seams. (3) Complete sets of equipment must be developed to adapt to the conditions of steeply dipping seams. (4) Overcome the steeply dipping face safety protection technical problems. In the last two decades, a number of universities, research institutes, and enterprises have realized the importance of safety and efficiency of steeply dipping seams in China. This is especially true of Professor Wu Yongping’s “hard coal layer safe and efficient mining” team at Xi’an University of Science and Technology. After several generations’ research and technical work, the team puts forward China’s longwall mechanized coal mining of steeply dipping seams strata control basic theory. This paper puts forth a series of key technologies of fully mechanized mining, develops and manufactures complete sets of equipment by independent innovation, and establishes a perfect face security system, forming a theory and technology system for fully mechanized longwall mining of steeply dipping seams."

Jan 1, 2017

By Alireza Ayoubian, Douglas S. Roy, Gianni O. Chieruzzi

"A 400 MW, gas-fed power plant on floating piles and piled raft foundations was constructed in the Province of Moskovskaya, Russia in 2008. The subsurface is characterized by fill underlain by loose to medium dense alluvial deposits, with peat and clay interbeds, a stiff to hard, highly plastic, silty clay stratum of glacial origin, and a stratum of very dense, varved interbeds of sand and silt.More than 800, drilled concrete piles were constructed at the site. The pile length ranged from 15 to 23 meters below existing surface grade, and the pile diameter ranged from 0.9 to 1 meter.Initial analyses by others predicted total power plant settlements of 3 to 4 cm when subjected to the permanent loading conditions. Under a peer review process for the equipment supplier, subsurface investigation and testing were performed to verify the consolidation parameters used for foundation design of the power plant foundation. The parameters obtained in this investigation were used in the 3-D finite-element model ELPLA as inputs for the settlement analysis of the turbine building and power island. The ELPA analyses predicted settlements on the order of 7 cm over a period of 30 years. The actual settlements after two years of monitoring were compared against the model predictions. The rate of settlement and the recompression index were both underestimated in our model. The measured settlements have enabled us to calibrate both of these model parameters so that the model better matches the data.IntroductionA 400 MW, gas-fed power plant was constructed near Moscow in the Province of Moskovskaya in Russia.Figure 1 shows the general arrangement of the main structures, and the geometry of the piles supporting those structures."

Jan 1, 2017