Search Documents

By Robert B. Fulton

Summary of data and estimates for 52 fluorspar properties in the following 13 foreign countries: Mexico Thailand China (PRC) Morocco Tunisia Italy Spain South Africa France United Kingdom Kenya Namibia Federal Republic of Germany Data includes deposit type, resource tonnage and grades, mining and beneficiation methods, annual production, fluorspar products and by-products, manpower requirements, capital and operating cost estimates. For operating properties, engineering and cost data have been developed for present and anticipated levels of production. Hypothetical operations have been assumed for undeveloped deposits.

Jan 1, 1984

By William L. Rice

This Bureau of Mines Open File Report on nickel is one of a series of minerals availability commodity deposit abstracts. Nonconfidential information from the Minerals Availability Program data base covering domestic and foreign nickel properties and deposits has been abstracted for use in this report. Abstracts include applicable data on location, published reserves and resources, geology, mine and beneficiation systems, and operation information.

Jan 1, 1984

By Donlad B. Lindsay

This report describes a field-test program to determine the effectiveness of a polymeric wall sealant to reduce the excape of naturally occurring radio-active gas radon from the walls of an underground uranium mine into the ventilation air. A 75-foot-long, dead-end drift with a surface area of about 6,000 ft2 was used as the test site in which the average natural radon flux from the normally dry rock was 16 fCi/cm2-s. The effect on radon emanation of wetting the walls with water to a depth of 3 inches was tested, after which the rock was completely covered with a coating of dry-mix concrete to provide a base for the sealant, an acrylic latex. Sealant was applied in two coats to about 0.25 mm thick. An overall reduction of average radon flux of about 75 pct was achieved. Radon production and other environmental values were measured continuously and automatically by a Bureau of Mines data acquisition system. A commercial microcomputer was programed to convert raw data to engineering units and to perform other useful operations while recording all data on magnetic diskettes. Direct measurements of radon flux from the rock surface were made by a charcoal adsorption technique.

Jan 1, 1981

By John E. Husted

Quantities of kaolin in Georgia in-contiguous or single bodies had been established by previous work to be sufficient for an alumina industry. The need for characterization of this kaolin to determine its suitability as an ore of aluminum resulted in the studies described herein. It was determined in an area roughly 7 x 27 miles, known as the Wrens district that approximately 5.9 billion short tons of kaolin averaging 35.55 percent A1203 exist in an essentially continuous clay body. The Macon-Sandersville district consists of discontinuous kaolin bodies averaging 35.28 percent A1203 with an average thickness of 28 feet. Tonnages for this district are not available. One hundred and twenty core samples of kaolin were analyzed for K20, CaO, MgO, Al203, T102, Cr203, Fe203, Si02, P205, and F. The P205 and F were analyzed by wet chemistry methods and the others by electron microprobe. Seventy-nine of the samples were from the Wrens district forty from the Sandersville-Macon district and one from the Andersonville district. Emission spectroscopic analyses were also made to qualitatively determine all elements present for each core. X-ray diffraction studies were made of each core to determine mineral species present. Scanning and transmission electron microscope pictures also are given for each I' core sample. Elevations, overburden thickness, and kaolin thickness are given for each core site as well as map locations. Isopachs for over-burden and kaolin thickness are given for the Wrens district.

Jan 1, 1983

By Michael Mancuso

This report summarizes the problems of topsail handling as related to present requirements of law and current equipment availability. The most prevalent topsoiling systems are reviewed along with a listing of advantages/disadvantages and best features of each system. Seven mining regions are included, along with an analysis of prevailing land use, types of soils and attendant physical, chemical am biological characteristics. There are several probable areas of future research "lined which can benefit mining, minimize the social impact of mined lands and speed the return of mined lands to more productive long-term use.

Jan 1, 1981

By Virgil A. Marple

It was the purpose of this contract to conduct research in several different areas of instrumentation used to determine the quantity of respirable dust in the mining atmosphere. One area of research was in evaluation of instruments including several respirable dust monitors, several types of photometers, and a QCM cascade impactor. An instrument evaluation chamber was developed to aid in evaluating the instruments in a dust atmosphere. Another area of research was investigations into new instrumentation concepts, such as a virtual impactor/photometer instrument, a new optical device which can be used as either an optical particle counter or photometer, a new personal respirable sampler, which employs an impactor instead of a cyclone as a preclassifier, and the development of a new cascade impactor, which deposits the particles uniformly on the impaction plate. Another area of research included the use of many of these instruments in two field studies, including a silica sand plant and a tungsten mine.

Jan 1, 1981

By Steve C. Albrecht

The objective of this study is "to assess the impact of surface mining on soil compaction in the Midwest". The study revolves around a unique field sampling program targeted at four mine sites utilizing four distinct types of soil movement of midwestern prime land. Through the preparation of a final report for use as a guidebook, an assessment is made of the degree to which surface mining operations contribute to the soil compaction problem. The final report is formulated through the use of field study data as well as information gathered in an intense literature review. The final report centers on applying collected data to practical field applications. Soil sampling on the four mine sites centers on a comparison of natural and replaced soils for moist bulk density. This characterization evaluates changes in density and texture throughout the soil profile to a depth of 48 inches. Fertility of the topsoil is also assessed for natural and replaced soils. During field sampling and observations, a base of information has been gathered to compile a case study on each mine site. The report accesses the regulations in the prime farmland areas through the use of a matrix. The regulatory matrix allows easy access of mining personnel to State and Federal regulations.

Jan 1, 1982

By Mark R. Pettitt

The development of fire hazard criteria for noise control products in underground coal mines are presented. Qualifying requisites of the criteria include maintaining miners' safety, allowing for maximum use of noise control products, and economic feasibility. The burning process is analyzed for its relationship to fire hazard criteria developed by NASA and the FAA, and the mine environment is analyzed in conjunction with the end-use applications of noise control products. Also, the interim fire hazard specification developed by MSHA is appraised as it applies to end-use applications of noise control products. From these analyses and a literature survey, fire hazard criteria are developed. They include an initial screening procedure that evaluates the level of flammability testing required. Fire tests that may be indicated are the Vertical Flame Test, the Ignition Temperature Test, and the 25-Foot Tunnel Test.

Jan 1, 1983

By L. A. Morley

Volume IV of the final report examines the problem of indirect contact of overhead high-voltage power lines by mining personnel. This refers to the contact of energized lines by workers through some intermediate conductor such as a metallic tool or a piece of high-reaching mobile equipment, thus the term "indirect contact." The shock hazard presented by such contact has been a major cause of electrical fatalities associated with mining operations. The report volume is divided into three major areas. The first gives a general background of overhead lines, basic characteristics, and associated hazards, and continues to describe presently used techniques and devices which attempt to alleviate the contact problem. The second area narrows the discussion to the mining industry by presenting a detailed analysis of 39 overhead-line contact accidents in mining since 1970. The third major section uses the information from the first two areas to formulate recommendations to prevent these accidents and subsequent electrocutions at mining operations.

Jan 1, 1982

By Lloyd A. Morley

This seven-chapter document is the first volume of a two-volume report that presents a comprehensive outline of coal-mine electrical power systems from theory to practice. Together, the two volumes contain the vital aspects that go into planning and designing a mine power system. After a short introductory chapter, Chapter 2 discusses the history of electrical use in mining and introduces "typical" mine- power-system arrangements. Chapter 3, 4, and 5 supply basic information on electrical theory, circuit analysis, and motors. Next, the Grounding and Distribution Chapters detail unique aspects of mine power systems. Elements of surface and underground use are included in all these chapters. An index concludes Volume I and is cross-referenced to both report volumes.

Jan 1, 1982

By Lloyd A. Morley

This eight-chapter document is the second volume of a two-volume report that presents a comprehensive outline of coal-mine electrical power systems from theory to practice. Together, the two volumes contain the vital aspects that go into planning and designing a mine power system. Building upon Volume I, the subject of protective equipment and relaying starts Volume II, first as an introduction in Chapter 8, then by a treatment of device selection in Chapter 9. Chapter 10 continues system protection in terms of transients and overvoltages. Chapter 11 describes the design of major power equipment, including power centers, switchhouses, and substations. Solid-state applications in mining are given in Chapter 12, and batteries and battery charging are discussed in Chapter 13. Chapter 14 covers electrical-equipment in hazardous locations of mining operations. The report concludes with Chapter 15, a discussion of electrical maintenance as well as some specific mine electrical problems. Information on surface and underground use is included in all these chapters. An index finishes the documentation and is cross-referenced to both report volumes.

Jan 1, 1982

By D. F. Hambley

This report documents the work carried out by Engineers International, Inc. and its subcontructor, W. G. Pariseau, in order to develop a design manual for ore passes for open pit mines. The work included an extensive information search, novel analyses in rock flow theory, cost and time estimation for shaft and raise construction methods, and development of design criteria for the are pass proper, dump point, and draw point.

Jan 1, 1983

By D. F. Hambley

This manual contains a step-by-step procedure for the design of ore passes for open pit mines. The manual is comprehensive and deals with all aspects including location, design, construction and operating considerations. In the construction section, all applicable raising and shaft sinking methods are considered and cost estimates and advance rates provided for each. The design process is divided into several sections - rock flow requirements, support design, dump point design and draw point design. Use of this manual provides open pit planning engineers with a means of designing and assessing the feasibility of ore passes for their operations.

Jan 1, 1983

By C. H. Larsen

The results of a comprehensive investigation of conveyance arrestment devices (safety catches) in United States coal mines are presented. Availability and use, performance, inspection, maintenance, testing, procedures, and regulatory requirements were investigated. Information was obtained from equipment manufacturers, mine operators, and regulatory-agency personnel, as well as from studies of domestic and foreign mining safety regulations. Traditional mine hoists and commercial elevators for mine use were investigated. Results of this and an earlier study of wire-rope practice in United States coal mines show a continued need for conveyance arrestment devices. A wide variety of these devices are in use. Only two types have been proved reliable for stopping a conveyance without injuring passengers or equipment. These are elevator overspeed-actuated wedge-clamp (Type B) safeties and broken-rope-actuated devices for wooden guides using a single-tooth-dog design developed in Ontario as a braking element. Elevators are widely used in U. S. coal mines. When maintained according to American National Standards Institute (ANSI) Specifications A17. I and A17. 2, they appear to present no major arrestment problems. Of 42 coal-mine hoists used for man transport that were inspected, 30 are in vertical and 12 in inclined shafts. Twenty-four vertical shafts use wood guides; 6 use steel. The 12 inclined-shaft systems use flanged-wheel T-rail guidance. Two wood-guided vertical-shaft systems use the single-tooth Ontario-type dog; the other 22 use multi-toothed wedges, cams, or dogs that have been proved highly unreliable. The arrestment devices in the six steel-guided vertical-shaft systems and in six of the inclined-shaft systems cannot be evaluated because performance data are lacking. The remaining six inclined-shaft systems have no arrestment devices at all. Of the 36 hoists with arrestment devices, the devices of 16 are never tested, the devices of 10 are actuated periodically with the conveyance at rest, and the devices of the other 10 are actuated periodically with a slow-moving conveyance. Although high speed is as probable as low speed in an emergency and would provide the best test of arrestment capability, no tests are performed in the United States which demonstrate the ability of an arrestment device to stop a loaded conveyance from high speed. Mine operators indicate little confidence in their conveyance arrestment devices, and manufacturers recognize a need to improve their products. Neither state nor Federal regulations provide a guide to this improvement. Mine operators, manufacturers, and state and Federal regulatory agency personnel would welcome specific guidance. In view of this, a set of application, design, actuation, stopping-performance, and testing and inspection criteria is presented as a guide to eliminating the inadequacies of these devices. Recommendations are included for improving hoist controls and machinery directly affecting conveyance safety.

Jan 1, 1972

The U.S. Bureau of Mines has been concerned for many years with the general problems of underground coal mining and the particular problems due to the methane content of the coal. The Bureau and others have worked diligently to improve the health and safety conditions for underground coal miners. It has been recognized for many years that the methane in coal would have some value if it could he recovered and used, Also its removal before coal mining began or during the mining cycle itself would make mining safer and more economic due to a potential saving in ventilation costs. The work covered in this report was carried out to review methods of removing methane from active and inactive regions of operating coal mines and to determine how the methane could be concentrated and utilized economically.

Jan 1, 1975

An evaluation of blasting procedures in surface mining operations was undertaken to determine means for improving safety. The objectives of the study were to: 1. Develop guidelines for safer blasting practices 2. Specify changes or additions in regulations concerning the use of explosives 3. Identify areas in which additional knowledge needs to be developed. As a basis for the evaluation, an idealized blasting cycle was prepared. Developed in the form of a scenario of surface mining operations, this synthesis of good mining practices served as the standard against which observed activities were compared. Blasting hazards were divided into two categories: those known to exist and those which are potential. Known hazards were identified in terms of situations which have actually resulted in explosives-related accidents. The evidence for known hazards was obtained primarily from MESA records of mine accidents. Potential hazards were identified by observation of mining activities and consultations with mining, explosive industry and government regulatory agency personnel.

Jan 1, 1977

By Mark S. Sanders

The purpose of the present study was to develop and test improved Type V workvests for use on dredge operations. The goal was to design workvests that would be more comfortable to wear, would interfere less with task performance, and would better meet the needs of dredge workers. It was hypothesized that by attaining these goals, the resulting vests would be worn more often and would be kept buckled more of the time than traditional vests. The study involved three major phases. In Phase I, visits were made to dredge operations and a definition of the problem was developed. Problems with current vests were identified and working conditions and tasks surveyed In Phase II, prototype vests were developed and laboratory tests were per-formed to assess comfort and interference. In Phase III, the prototypes were modified and field tested with actual dredge operators and workers.

Jan 1, 1985

By Terrence J. Stobbe

The authors investigated the nature, cause and treatment of 234 back injuries which occurred in 156 different situations in underground coal mines. A detailed interview was conducted with each injured miner as 137 variables were explored to provide a complete picture of the injury scenario. The miners worked at 23 mines in six states. An important finding of the study was that sudden movement, which occurred in 527 of the injuries, is a more frequent factor than heavy lifting in causing hack injuries. Along with sudden movement, other major injury causing factors were equipment seat design, lifting, cable handling, and slips/trips. No significant differences were found between the injury scenarios associated with lost time and non-lost time injuries; thus, both sets of scenarios should he used in doe loping back injury control strategies. Medical treatment and rehabilitation varied in content and quality. Dialogue between the medical, rehabilitation and mining communities is needed to develop an effective treatment strategy. Back injury control related training was found to be inadequate in most mines. Mine specific training for physical stress recognition and potential sudden torte release should he added to the training currently given. Based on the information collected in this study, recommendations were made regarding equipment design, mechanical assists and procedures for material handling, training, etc., which, if implemented, will assist in reducing the frequency of back injuries in underground coal mining.

Jan 1, 1989

By T. G. Carnahan

In-place leaching is being actively utilized to extract uranium, copper, and evaporites from low-grade and difficult-to-mine ores. The purpose of this report is to discuss in-place leaching technology, its advantages and disadvantages, and to give an overview of past, current, and envisioned in-place leaching operations in the U.S.A. Application of in-place leaching to uranium ores has been particularly successful because the conditions for leaching are nearly ideal. The ores are generally in highly permeable sandstone aquifers bounded above and below by impermeable shales. The uranium ore minerals are easily leached with oxidizing acid or base solution and the pregnant solutions are amenable to ion exchange concentration and purification prior to conventional solution neutralization for recovery of yellow cake. Copper is routinely recovered from sub-grade rock by dump leaching at most major copper mines. Acidified ferric sulfate is either sprayed on the surface of the dumps or is ponded on top of the dumps. The leaching solution migrates down through the rock and dissolves copper. The solution is collected from the base of the dumps and copper is recovered by solvent extraction-electrowinning or by cementation on detinned steel cans. True in-place copper leaching is being practiced in the caved stopes of an exhausted underground copper mine. Other innovative in-place copper leaching techniques have been tested commercially and laboratory- and pilot-scale experiments have been conducted to investigate proposed in-place leaching techniques for extracting copper from difficult-to-treat chalcopyrite ores. Solution mining of evaporites is being conducted commercially for the extraction of sodium chloride and potassium chloride. A large-scale experimental project for solution mining of trona has been undertaken.

Jan 1, 1982

By L. B. Phelps

A method is presented for the burial of potentially toxic spoil in high density zones or packages within spoil piles. Such burial could reduce the outflow of pollutants and thus minimize contamination of groundwater flows. Laboratory model studies using ammonium bromide tracer were performed to quantify the expected outflow mixing that could be achieved through package construction in spoils. Field drilling and geophysical density logging of spoils was carried out at three sites in Pennsylvania and Ohio to obtain a range of field spoil bulk density measurements and spoil samples. These data are analyzed to determine the relationships between spoil density and the controlling factors of lithology, depth, age, particle size distribution and mining method. A separate series of spoil permeability tests were performed in the laboratory to investigate the relationship between permeability and its related parameters. Research results are applied to the toxic package method to suggest guidelines for pack-age size, shape, density and placement for future field prototype development.

Jan 1, 1981