Search Documents

By Alfred Bellows

The objective was to develop and design a remotely operated temporary roof support system that provides a safe working environment between a freshly cut coal face and the last line of permanently supported roof in which to perform roof bolting activities. This system was to take the form of a retrofit package which could be adapted to a majority of the bolters currently in service. The result is an integrated piece of hardware which will retrofit onto virtually all single boom bolters by removing the drill boom and relocating and modifying the hydraulic controls. The system is composed of three basic components: a pair of cantilevered roof supports which reach forward to the desired line of support, a mast type drill unit for drilling holes and torquing bolts, and a transverse slide assembly to carry the drill from hole to hole across the entry without relocating either the bolter or the roof support. A converted bolter not only provides a much safer operation but is projected to increase the production speed as well as reduce the manpower required to operate a section.. This improvement in productivity is shown to make the job of retrofitting a bolter cost effective in less than two months and provide a potential profit thereafter. Based on the findings presented in this report it is recommended that a proto-type be built and tested in an underground coal mine to demonstrate its effectiveness.

Jan 1, 1976

By R. J. Gunderman

Explosionproof electrical enclosures for coal mine face equipment have been of the same basic design for many years without significant change. Characteristics for potential improvement were investigated through interviews, visits to mines and studies. Improved safety, health and productivity were the goals. Areas identified for improvement included rapid venting of pressure build-up due to an internal explosion, quick and easy entry or removal of cable entrances, and a quick and easy cover removal for rapid component access. Concepts were identified and evaluated, and the more promising devices were fabricated and tested. Encouraging results from initial tests led to further design refinement and establishment of design guidelines. These design guidelines for a pressure vent and for an elastomeric grommet type cable entry are described along with the testing used. An application for an experimental permit was requested from MSHA. After test and evaluation experimental permit #396 for evaluation in an underground coal mine was granted.

Jan 1, 1980

By Alice M. Chieruzzi

This Country Documentation Report presents the development of economic indices for Zambia for the period from 1970 through 1981. The work done through the Bureau of' Mines, Minerals Availability Program, under Contract number J0225001. This contract calls for the development of twelve index time series describing factor input costs in the mining sector of 95 countries. The twelve index time series describe the costs of: 1) mining wages, 2) construction wages, 3) equipment and repair parts, 4) bits and related steel, 5) timber and lumber, 6) fuel, 7) powder and blasting agents, 8) tires, 9) construction materials, 10) industrial materials, 11) transportation, and 12) electrical power. These indices combined with weight factors being developed by the personnel of the Minerals Availability Field Office (MAFO) of the Bureau of Mines in Denver, Colorado, will be used to perform instantaneous updates of all costs relating to the mining industry. The indices were developed primarily for use in the Bureau's Minerals Availability Program in assessing the worldwide availability of nonfuel minerals.

Jan 1, 1983

By G. F. Kuncir

The analysis summarized herein evaluates the Bureau of Mines Program for Advancing Mining Technology Oil Shale in terms of the economic benefits which may be derived for the Nation as a result of its successful research and development efforts. On the basis of postulated oil shale production scenarios, benefit-cost ratio indicators are computed for the program elements as they apply to surface, underground, and modified in situ oil shale mining systems. Eight value indicators are used to measure the Program's beneficial impact on the future oil shale industry in relation to planned research and development costs. These are: capital cost savings, operating cost savings, labor savings, environmental quality maintenance cost reduction, reduction in production costs, byproduct production benefits, total production benefits, and additions to recoverable reserves. Program costs are aggregated from 1974 through 1987 and major benefits are accrued from 1982 through 2040. Both cost and benefit streams are discounted to mid-1975 present value.

Jan 1, 1977

By K. B. Bengtson

This task report provides the process technology, preliminary design, capital and operating costs for a 25 TPD pilot plant to produce cell-grade alumina using a clay/hydrochloric acid extraction - HCI gas induced crystallization process. The report consists of six volumes: I - Process Technology and Costs; II and III - Equipment Lists, Specifications and Quotations; IV and V - General Specifications; VI - Drawings. The process was selected by the Bureau of Mines as the more promising method to produce cell-grade alumina from clay based on the results of the two previous task reports under this contract: Task I - Comparison of Six Processes (alunite, anorthosite-lime sinter, clay/sulfurous acid, clay/nitric acid, clay/hydrochloric acid evaporative and gas-induced crystallization) and Task 2 - Comparison of Two Processes (clay/nitric acid and clay/hydrochloric acid - gas induced (crystallization). The pilot plant process utilizes a unique dual crystallization process to produce aluminum-chloride-hexahydrate crystals having sufficient purity when decomposed to meet stringent alumina product specifications. The size of the 25 TPD pilot plant has been selected to permit scale-up to commercial size plants of equipment, technical and economic parameters. The capital cost estimate for the pilot plant, exclusive of fee and escalation, for a southeastern U.S. location is $52,311,000 expressed in 1979 dollars. The total time required to construct the pilot plant including engineering and procurement is 32 months. The operating cost to produce the estimated 9,000 tons of alumina required for testing in Hall cells is $40,91[0],190 expressed in 1979 dollars.

Jan 1, 1979

By G. F. Kuncir

The time-cost-risk analysis described herein was performed as part of an evaluation of the Advancing Oil Shale Mining Technology Program performed by The Aerospace Corporation. The objectives of this analysis are to assess the feasibility of the program relative' to time and cost constraints, and to determine the probabilities of achieving various technological goals. A combination of standard program planning and analysis techniques were used to achieve these objectives. These included a critical path analysis, a resource allocation analysis, and a risk analysis.

Jan 1, 1977

By G. F. Kuncir

The analysis described herein evaluates the Bureau of Mines Program for Advancing Mining Technology - Oil Shale in terms of the economic benefits which may be derived for the Nation as a result of its successful research and development efforts. On the basis of postulated oil shale production scenarios, benefit-cost ratio indicators are computed for the program elements as they apply to surface, underground, and modified in situ oil shale mining systems. Eight value indicators are used to measure the Program's beneficial impact on the future oil shale industry in relation to planned research and development costs. These are: capital cost savings, operating cost savings, labor savings environmental quality maintenance cost reduction, reduction in production costs, byproduct production benefits, total production benefits, and additions to recoverable reserves. Program costs are aggregated from 1974 through 1987 and major benefits are accrued from 1982 through 2040. Both cost and benefit streams are discounted to mid-1975 present value.

Jan 1, 1977

1.0 Control House (DWG. NO. 56-401-G) - 1.1 Physical Description The Control House is a single story, 2728 square foot building with an adjacent transformer yard. A four foot overhang provides shade protection for the walls. The building is heated and air conditioned. The HVAC System has an elevated outside air intake and provides a positive pressure environment within the structure in order to prevent the infiltration of heavier-than-air, noxious gases. The materials of construction are as follows: Structure : Light-Gage Metal Framing Exterior Walls :Outside - Preformed, Metal Siding :Inside - Insulated Metal Liner Panels Interior Partitions :Gypsum Board over Light-Gage Metal Framing Roof :Insulated, Preformed Metal Panels Ceilings :Mechanical & Electrical Rooms - Exposed underside of Roof Panels Control Room, Lunch Room, Toilets, Entry - Suspended Acoustical Lay-In Tile Floors :Mechanical & Electrical Rooms - Concrete Slab on Grade Control Room, Lunch Room, Toilets, Entry - Resilient Tile Exterior Doorsand Windows :Preformed Metal Panel Manufacturer's Standard Units

Jan 1, 1979

By G. F. Kuncir

This volume was prepared in support of an evaluation of the Advancing Oil Shale Mining Technology Program performed by The Aerospace Corporation under a Bureau of Mines contract. The evaluation is described in part within a companion volume entitled Benefit-Cost Analysis. The economic mine models outlined herein provide a quantitative basis for the assessment of program benefits. Reference is made to estimated oil shale mine costs to delineate the beneficial impacts that can be expected to accrue for the future implementation of program developed technology. Estimated mine cost data are provided for surface, underground, and modified in situ oil shale mining operations.

Jan 1, 1977

1.0 SCOPE AND REGULATIONS 1.1 This specification covers the minimum requirements for material handling and associated equipment including design and materials. 1.2 This specification requires compliance with all federal, state, local laws and regulations which may be applicable including the Occupational Safety and Health Act, Construction Safety Act as well as rules, regulations and standards of the Secretary of Labor.

Jan 1, 1979

By Mackenzie Burnett

The Brattice Window Method was used to measure the leakage rates of a total of 42 ventilation stoppings in 8 hardrock mines. Various types of stopping construction were evaluated. The following types are listed in order of decreasing effectiveness: 1) Cinder block, 2) Timber and mortar, 3) Timber and polyurethane foam, and 4) Timber and brattice material. There are slight differences in the effectiveness of the first three types, while the timber and brattice type is substantially inferior to the others. The repeatability of the Brattice Window Method was found to vary with physical conditions in the mine such as stopping location with respect to intersections, regularity of drift cross section, and the presence of hardware such as air and water pipes, timber sets and wire mesh. The Brattice Window Method is viewed primarily as a tool for estimating and comparing stopping leakages for the purpose of determining where repair efforts should be concentrated. A laboratory test program resulted in the derivation of several "rules of thumb" for employing the Brattice Window Method, which will aid in securing accurate and repeatable data.

Jan 1, 1979

By R. Stefanko

In this report, the use of Penn State Ventilation Simulator (PSU/MVS) for planning and evaluating new coal mine ventilation systems is demonstrated. The simulator's application to evaluate the ventilation system of a coal mine currently under development is discussed. The ventilation system is evaluated for representing development of the mine at the end of 12, 24 and 36 months after mining has begun. The report describes the necessary steps of data input preparation, ventilation network development, analysis of results, modifications to the network, and methods to expand the computer program for networks larger than 550 branches.

Jan 1, 1977

By G. W. Luxbacher

This volume describes the use of the Penn State Mine Ventilation Simulator (PSU/MVS) to model existing mine ventilation systems and, in addition, to evaluate the effect of system modifications. Ventilation survey methods designed to insure computer input data of sufficient accuracy for simulation purposes are covered in comprehensive detail, including quantity and pressure measurement and fan performance testing. The development of input data from ventilation survey results is discussed and illustrated by the use of an actual field survey. Two programs, written in FORTRAN IV with WATFIV, are presented to calculate airway head losses from altimeter pressure measurements. An existing coal mine ventilation system is analyzed and modifications to the system are simulated and evaluated. In addition the application of the PSU/MVS to non-coal mines is briefly discussed. An extensive bibliography on ventilation surveying and simulation is included.

Jan 1, 1977

By William J. Douglas

This document describes the development of a conventional mining equipment data base, and an approach for conducting industrial engineering studies of arbitrary mining systems employing network techniques. Data was acquired through underground time studies. Each member of a four-man field team was assigned to a specific machine during each shift for which observations were conducted. Using digital wrist watches and networks describing the man-machine interactions, all events occurring luring the course of each shift were recorded on cassette tapes. The tapes were transcribed, coded, keypunched, and validated using computerized editing techniques. The resulting data files were processed to provide statistics relating to activity durations and event frequencies. The results were used to evaluate operator, machine, and system performance for each section which was observed. Equipment, reliability, and maintainability analyses were conducted using the industrial engineering data files in conjunction with historical information collected at the mine site.

Jan 1, 1976

By John H. Johnson

This report covers the third and final year of work conducted under U. S. Bureau of Mines Grant G0166027, "Monitoring of Mine Air Pollutants". The report discusses work performed in three areas. These are the White Pine Mine (WPM) Experimental Unit, diesel mine-vehicle tailpipe emissions monitoring, and mine ambient air concentration data analysis. The WPM experimental unit was used to study diesel exhaust stratification in an 80 foot long dead-end heading while loading ore with a Wagner ST-5D scoop train LHD. The MTU Mine Air Monitoring Laboratory (MAML) was used to gather temperature and CO2 concentration data at 10 locations. Three different ventilation conditions were compared. The data substantiate the presence of strong buoyant forces of the hot exhaust gases which result in temperature stratification in dead-end headings. The diesel mine-vehicle tailpipe emissions monitoring study involved laboratory measurements of diesel undiluted exhaust pollutant concentrations by the portable tailpipe emissions measurement apparatus (EMA) assembled for in-mine use. The results were compared with simultaneous measurements by standard laboratory exhaust monitoring instruments. These results indicate that accurate field source quality control measurements can be obtained for CO2, CO and NO but NO2 results were low for all engine conditions. The mine ambient air concentration data analysis study included analysis of diesel pollutant concentration data in the Orchard Valley Mine air and comparison of the results with data collected earlier in the White Pine and Brushy Creek mines. The analysis included preparation of lognormal frequency distributions and calculations of C02-based concentration ratios and correlations. In the three mines compared, pollutant concentrations are distributed quite similarly, and the concentrations appear to be controlled to present standards.

Jan 1, 1979

By R. Stefanko

The industrial hygiene and safety aspects with internal combustion engine in mining systems is truly interdisciplinary and encompasses many fields such as mine ventilation, exhaust gas and particulate analyses, mine atmospheric environment monitoring, mathematical modeling of generation, dilution and dispersion of pollutants in ventilation systems, and engine testing and approval. Mathematical models of the dilution and dispersion of diesel exhaust contaminants can be useful only if these models can be validated. In this research report, experiments that were specially designed for the above purpose are described. These experiments were conducted in the U.S. Bureau of Mines, Safety Research Coal Mine, in Bruceton, Pa. On the basis of this study, the data collected, and further review of available literature, it is concluded that mathematical models of dilution and dispersion are useful tools for mine ventilation planning. Additional objectives of this study about which conclusions and recommendations are reported here include: (a) evaluation of mine atmosphere contaminant monitoring systems; (b) optimum sampling site locations; (c) model sensitivity and error analyses; (d) computer coding of mathematical models; and (e) development of a diesel bibliography. While an extensive bibliography on diesels is provided in this report, Volume II of this final report has 511 references.

Jan 1, 1977

By Larry R. Powell

As part of the Bureau of Mines effort to establish a comprehensive subsidence data base for subsidence technology development, subsidence and related data are being compiled for various mining, geological, and environmental situations. This publication presents data for a longwall mining operation in the Northern Appalachian Coal Region. Vertical displacements and relative face positions are tabulated for 110 subsidence monuments. Measurements were taken twelve times during the eight months it took to mine the panel. Brief physiographic and geological descriptions of the mining site are presented along with a general account of the mining and subsidence monitoring methods.

Jan 1, 1981

By R. V. Ramani

The industrial hygiene and safety aspects with internal combustion engines in mining systems is truly interdisciplinary and encompasses many fields such as mine ventilation, exhaust gas and particulate analyses, mine atmospheric environment monitoring, mathematical modeling of generation, dilution and dispersion of pollutants in ventilation systems, and engine testing and approval. This bibliography, therefore, is a compilation of references from interdisciplinary sources pertaining to diesels and related areas. Related areas are defined as those concerned with: (i) mine ventilation system design and operation; (ii) description, measurement, modeling and monitoring of mine atmosphere contaminants, and (iii) tests, standards, selection procedures, and operational practices for internal combustion engines in underground mines. References cited from source materials span the years 1900 to early 1977. Total number of references cited is 511. Subjective criteria governed the definition and selection of references. Therefore, this bibliography is not claimed to be all-inclusive nor does it purport to be an exhaustive search of all sources.

Jan 1, 1977

By Larry R. Powell

As part of the Bureau of Mines effort to establish a comprehensive subsidence data base for subsidence technology development, subsidence and related data are being compiled for various mining, geological, and environmental situations. This publication presents data for a longwall mining operation in the Northern Appalachian Coal Region. Vertical displacements and relative faze positions are tabulated for 160 subsidence monuments. Measurements were taken 32 times during the 2 years it took to mine the two panels. Brief physiographic and geological descriptions of the mining site are presented along with a general account of the mining and subsidence monitoring methods.

Jan 1, 1981

By D. D. Hamilton

The ISMS program provided for the development and demonstration of equipment modifications for improved safety in both conventional and continuous coal mining systems. This report documents the success of the program in identifying accident hazards in underground coal mines with 4-to 8-foot seam heights, in designing modifications to reduce the hazards, and in demonstrating improved safety through extended underground use of the ISMS equipment.

Jan 1, 1977