Search Documents

By Kenneth E. Hay

Researchers from the U.S. Bureau of Mines conducted a field study to assess the safety of remotely controlled mobile roof supports (MRS) in a retreat pillar mining operation, Data were collected to provide the Mine Health and Safety Administration with criteria needed to develop guidelines for MRS use and to determine if precursors could be identified that would alert miners to imminent roof falls. Two test sites at which two different support methods-MRS's and posts were used and were monitored to obtain information on entry stability. Pressure transducers and string pots were installed on all four MRS's to obtain loading and displacement information. and roof bolt load cells. sonic probes, extensometers, and survey targets were installed in the surrounding entries to obtain information on ground behavior. Results showed a larger increase in roof bolt loading and roof movement when MRS's were used, especially in the intersection area. Roof bolt loads in the entries showed decreases in load when the MRS's were set and increases up to 11,1 kN (2,500 lbf) when the MRS's were unloaded. Unloading of one MRS in a pair did not significantly increase load on the other. MRS's I and 2 usually had the higher loads, with these loads increasing as the pillars on each side were being mined. MRS 3 normally had lower loads than I and 2: however, it also experienced some very high loads when in the last position near the pushout. MRS 4 usually had the lowest loads, primarily because it was located near the solid pillar that was not being mined.

Jan 1, 1995

By S. Ramatsoma, D. N. C. Phillpotts, B. Whitehead

Changes in flotation performance have been correlated to changes in froth structure, velocity and stability. Literature has shown that when the aeration rate is varied for a specific float cell, the recovery of the valuable mineral reaches a peak which also coincides with a peak in the air recovery – a measure of froth stability. Peak air recovery optimisation methodology is a way to use direct readings of physical phenomena by froth cameras to optimise the metallurgical performance of a flotation plant. The aim of this paper is to show the transient nature of the peak air recovery value and the variety of conditions required to attain the peak air recovery on an industrial flotation plant with tight base-layer control of the feed and internal conditions. Industrial site tests that were conducted under controlled conditions showed different peak values at significantly different corresponding aeration rates during normal operation. The measured peak air recovery points corresponded to maximum PGM recovery during normal flotation, as expected. This dynamic nature of the peak air recovery point conditions has not previously been discussed in literature and indicates the need for online measuring equipment and informs the design of process control algorithms required to exploit the phenomenon for optimisation. Keywords: Froth flotation, flotation control, flotation optimisation, peak air recovery

Jan 1, 2020

By Stephen Buttling, Zhong Rui

"A single unit gas fired power station was being built on the edge of the Gulf of Thailand in 2001. The soil conditions consisted of very soft to soft Holocene Marine Clay, and the site was part of a coast line which had been subsiding below high water mark for some time. In order to provide access around the power station a road system in a figure-of-eight formation was required, and this also needed to be above the design flood level, allowing for future settlement. A ground improvement scheme was proposed and constructed, which consisted of two spacings of prefabricated vertical drains (PVD) over two depth ranges, vacuum consolidation and pre-loading, and rigid inclusions.During the construction phase, the vacuum consolidation was applied for 202 to 221 days in different zones, and monitoring allowed a prediction that the future settlement, including secondary consolidation over a period of 25 years, would be within the range of 175 to 355 mm, which met the contract requirement of less than 400 mm.The power plant was completed and became operational in 2003. Monitoring of the road levels continued, as did the settlement, and in early 2010 the total settlement since the end of vacuum consolidation had reached about 800 mm. The monitoring data both during the ground treatment and for the following 7 years is presented and analysed. This is supported by numerical analysis using 3D finite element methods which shows good agreement with the measured data, and allows a preliminary explanation as to why the predictions were so far out.BACKGROUNDAfter a period of bidding and negotiation, the Eastern Power and Electric Co Ltd (EPEC), an Independent Power Producer, entered into an agreement with the Electricity Generating Authority of Thailand (EGAT) in November 1997 to sell them power. In 1999 an Engineering, Procurement and Construction (EPC) contract and an Operation and Maintenance contract were signed with a supplier to provide a gas-fired (with oil as a back-up fuel) 350 MW combined cycle power plant in Bang Bo, Samut Prakarn Province, east of Bangkok. The site of the plant at Bang Bo is located immediately to the east of the Samut Prakarn Wastewater Treatment Plant, adjacent to the Gulf of Thailand (see Figure 1) in an area of very soft to soft marine clay (Bangkok clay) having low shear strength and potential for excessive settlement. The site layout comprises the main Power Plant components of generating block, cooling towers, fuel unloading area and storage tanks, switchyard and administration block, separated by access roads."

Jan 1, 1900

By Richard E. Thill

Backfilling of mine voids is used to prevent or control the effects of subsidence on surface structures. The pumped-slurry, blind-backfilling process has been particularly successful for stabilizing ground over abandoned and inaccessible underground coal mines. Using this newer technology, vast quantities of backfill material can be distributed over wide areas in underground openings from a small number of injection boreholes. The rapid and successful development of this backfilling method, however, has outstripped technology for monitoring and controlling backfill placement. Surface or borehole remote sensing methods are needed to determine where fill material is being distributed underground and how effectively the material is packed in the voids. In search for improvements in backfill monitoring and control technology, potential remote geophysical sensing, process monitoring, and tracer methods were evaluated to select candidate systems for monitoring backfill placement under the constraints imposed by the injection process and the surface and subsurface conditions. ' A multiple objective ranking matrix, based on theoretical considerations as well as pragmatic experience with systems working in related or similar conditions, was used to narrow down potential methods to several most-favored candidates. Two of the candidates were field tested under actual operating conditions at a backfilling site in the Wilkes-Barre-Scranton region of northeastern Pennsylvania. Although process and acoustic emission monitoring indicated promise for improving existing backfill monitoring technology, more extensive testing under different conditions at various sites is required to establish the validity and utility of these methods. Results indicate that no single method is adequate in itself for backfill monitoring, and that a successful system will require the Integration of several methodologies.

Jan 1, 1982

By B. Papilon

Dynamic pressures during blasting can affect performances of both electronic and non-electronic detonators. Boreholes can develop tremendous amount of pressures during blasting. The effect of such elevated pressure especially during electronic delay countdown is probably more acute in electronic detonators. Measuring the pressures during blasting can aid to understand the relationship between magnitude of the pressure developed and the multitude of blasting conditions.

Jan 1, 2013

By F. Charette

Instrumentation has been developed that can monitor the strain applied to a D-Bolt up to 7.5% elongation. The technology far exceeds the limit for foil resistance strain gauges. In the laboratory the instrumentation has provided insight into the fundamental behaviour of the D-Bolt following yield. Currently the instrumentation is undergoing field trials at a number of Canadian Mines. Discussion on field results is provided with regards to significance, reliability and temperature effects.

Aug 1, 2013

By S Maryati

Surface mining activities disturb large areas, produce great sediment loads and tend to be a source of water pollution if they are not managed properly. Coal mining in Indonesia has a very high risk of soil erosion because the coal mining areas are generally located in tropical areas with a high average of rainfall (4000 - 6000 mm/year) and use surface mining methods. The main factors affecting erosion risk are climate, soil type, topography, vegetation cover and management factors. Thus, the monitoring of erosion risk in mining areas is very important due to the characteristics of coal mining in Indonesia. The objective of this research is to determine the ability of satellite images (remote sensing data) and geographic information systems (GIS) to provide an accurate and up to date spatial database for the monitoring of erosion risk in surface coal mining areas using the Universal Soil Loss Equation (USLE) method.The erosion risk analysis and spatial data processing are generated by the ArcGIS 9.3 software and need several data, namely: an erosivity map, erodibility map, a slope map, vegetation index map and land management or land cover map. The erosivity map is derived from the rainfall data, whereas the erodibility map is derived from the soil map. The slope map is derived from the SRTM-DEM (Shuttle Radar Topography Mission-Digital Elevation Model) and processed using 3D analyst tools. Furthermore, the vegetation index map and land cover map are derived from a satellite image using digital image processing techniques.This preliminary study produced results that show soil erosion monitoring, which is integrated with remote sensing and GIS technologies, has great potential for producing accurate, advance, and low cost erosion risk maps in coal mining areas. This map is very important for getting spatial distributions of the erosion and useful for developing erosion management plans.

Nov 22, 2011

By Robert C. Freas

Dravo Lime Company has opened a new 290m (940 ft.) deep lime-stone mine near Maysville, Kentucky. As the mine was opened there were many unknowns as to the stress relationships within the rock, and their influence, if any, on the selected mining method. Therefore, a system of overlay geologic and structural maps, borehold extenso-meter measurements, and oriented photography was developed for the purposes of monitoring the internal structural relationships of the rock mass. This paper presents a description of the methods used, the observations made, and the conclusions and recommendations made as a result of the initial monitoring program.

Jan 1, 1977

By Todd Minoski, KRISTIN FLOYD, Michael Murphy, VASU GANGRADE, Gamal Rashed, DYKE MARK VAN, Brent Slaker

Underground stone mines frequently operate on multiple mining horizons or are required to undermine or overmine old workings. In these situations, the effects of pillar columnization and interburden thickness on the stresses surrounding mine workings are poorly understood. Many old workings were not designed to consider the effect on future undermining or overmining and, as a result, are laid out on irregular patterns and with pillar sizes that are difficult or impossible to replicate on adjacent levels. Additionally, as depth increases, even a consistent gridded mine layout may result in poor columnization due to the need to increase pillar sizes. Rules of thumb and past practice for designing multiple levels may often be effective. This paper explores the effect that multiple-level stone mining has on stress redistribution through the discussion of two case-study mines and associated numerical modeling to provide additional insight into situations which may cause concern.

By Klein E., Kinscher J., Lizeur A., De Santis F., Lhoumaud E.

Seismic repeaters are rarely observed phenomena in underground mines. However, recent studies in Garpenberg mine (Sweden) have demonstrated that seismic repeaters and multiplets may represent significant portion of the total number of microseismic events (> 80 %) related to excavation operations. Detailed seismic analysis, involving template matching, multiplet clustering, double-difference relocation, source parameter and mechanism estimation, and interevent time analysis, suggest that seismic repeaters represent brittle frictional parts (asperity) of creeping, planar shaped, pre-exiting structures of several meters length. It is furthermore suggested that seismic repeater occur preferentially in weak rock-mass materials (e.g. talc) associated with strengthening friction behaviors. These results may imply that postblast related stress redistribution may be governed by “silent” aseismic movements in preferentially weak rock mass materials, what questions the reliability and performance of seismic monitoring to survey stress evolution during excavation operations. However, once the seismic and aseismic coupling processes and the geological nature linked to repeater occurrences are better understood, their detailed monitoring bears also opportunities to survey and quantify aseismic post-blast stress transfer. Here we present ongoing investigations on repeater occurrences aiming at better understating on their geological and geomechanical origin. Furthermore, we try to develop advanced monitoring tools helping to quantify aseismic slip and to provide criteria for seismic hazard as asperity density and the related potential to generate larger dynamic rupture zones. For this respect a local monitoring network has been set up close to certain repeater target families. Furthermore, geological well log drilling throughout repeater occurrences as well as geotechnical strain measurements (e.g. extensometer, optical fiber etc.) are currently conducted to provide crucial information on the geological nature of repeater and to quantify and characterize background creep induced from excavation.

Apr 26, 2022

By T. Schepp, T. Friedrich

"The natural stage of deep mines operation is a closure of unnecessary shafts. It is extremely important to ensure a proper shaft closure to avoid stability loss and the associated damage to surface facilities in the future. For the still active shafts, it can be done by a dedicated shaft closure design, but even then, depending on the shaft closure method, it may be necessary to perform regular shaft inspections. The paper presents a short overview of shaft closure methods and available tools and devices developed in the last time for such shaft inspections. INTRODUCTION The natural stage of deep mines operation, commonly occurring after depletion of the reserves of mined materials, is a closure of unnecessary shafts. All over the world, the number of liquidated shafts grows continuously and the problem of shafts disposal is especially critical for deep shafts. The typical depth of 600 m of currently liquidated shafts in Poland may already be seen as a challenging task. The greater is the challenge of shaft closure in Germany where the last active coal mines for shafts with a depth of up to 1,300 m have been recently closed. It is therefore extremely important to ensure a proper shaft closure to avoid stability loss and the associated damage to surface facilities in the future. For the still active shafts, it can be done by a dedicated shaft closure design, but even then, depending on the shaft closure method, it may be necessary to perform regular shaft inspections. In many cases, it is more important to inspect old, abandoned shafts, where the wall stability or even liner type are not fully known. SHAFT CLOSURE METHODS Abandoning a shaft is a complicated task, as shafts, being the link between the surface and an underground network of workings, disturb hydrogeological and gaseous conditions in the rock mass (Sztelak, 1991). Closure procedures at older mine sites have been carried out in accordance with earlier legislative requirements. For very old shafts (+100 years), it means in many cases only a sealing of the shaft entrances by means of timber or concrete slabs. In the 20th century, the shafts were also closed by means of filling with grainy materials, but even then the retrospective activities at abandoned mine sites were extremely limited and in most cases no further monitoring measures were performed. The possible consequence of an improper shaft closure and lack of monitoring is presented in Figure 1."

Jan 1, 2019

By Peter Cain

The Phalen Colliery in the Sydney Coalfield is extracting the 2.6 m thick Phalen Seam by the panel and pillar longwall retreat method. Abandoned workings occur in the Harbour Seam 140 m above and overlie the Phalen Colliery. Parts of these workings are flooded, and pose a number of questions relating to the safety of operations in the Phalen Colliery. In order to answer some of these questions, the Cape Breton Development Corporation re-entered an abandoned non-flooded roadway in the Harbour Seam directly above a retreat panel in the Phalen Seam to allow the deployment of instrumentation to monitor interaction effects. Fifteen monitoring sites, each 4.5 m apart, were installed in the 5 East Top Level after it had been re-entered and made safe. Each monitoring station included a vibrating wire strain gauge piezometer and a potentiometric extensometer. The piezometers were attached to rock bolts anchored into the floor and were connected by a flexible standpipe to a constant head apparatus. Variations in hydraulic head due to subsidence were monitored to determine subsidence. The extensometer units were mounted on rock bolts anchored into the floor of the roadway beneath the ribside and monitored ground strains. The instrumentation was capable of remote reading in the event that access to the site was restricted after installation. This paper describes the instrumentation, the installation programme, and some preliminary results.

Jan 1, 1993

By James JV, Petho SZ

The South Deep surface shaft system is being sunk to a final depth of 2750 in below surface and on completion will be the deepest single drop haft in the world. The shafts will intersect the target reef horizon at 2650 to below surface. In order to negate the requirement for a shaft pillar, which would he extremely large at this depth, the reef horizon in the vicinity of the intersection is currently being mined. A high quality crushed waste/classified tailings backfill is being placed in the longwall stoping panels around the shaft intersection area. This kill limit closure and ride which following shaft reef intersection could have a detrimental effect on the long term shaft stability. This paper discusses underground instrumentation results and numerical modelling exercises carried out to confirm that the shaft system will he stable throughout the life of the mine. Instrumentation projects include closure and ride measured between backfill paddocks and haulage leveling exercises carried out to determine the far field rockmass response to mining with stiff backfill.

Jan 1, 1998

By H. M. Kim, J. Rutqvist, D. W. Ryu

"Demand of high pressurized gas storage in underground rock caverns is increasing. Compressed natural gas (CNG) and compressed air energy storage (CAES) are one of the promising examples after since lined rock cavern (LRC) concept has been verified through in-situ pilot tests. Two key essential concerns of high pressured gas storage in underground rock caverns are mechanical stability of the cavern against high inner storage pressure and the risk of gas leakage from the caverns.In this study, we introduce our results of numerical simulations so as to investigate the potential of monitoring for gas leakage at a pilot facility for CAES in underground LRCs. The pilot facility was constructed at a comparatively shallow depth of 100 m, compared to the previous cases with several hundreds of meters, aiming at validating the feasibility of the LRC storage concept in which inner sealing liners, consisting of steel plate and concrete linings, are installed inside the excavated rock caverns (KIGAM, 2011). Compressed air may leak through either initial defects of inner containment liners such as imperfect welding regions and in-situ construction joints of the liners, or through structurally damaged points of the liners during the CAES operation where compression and decompression of the caverns are necessarily repeated and their structural robustness can be deteriorated.For this perspective, we carried out a coupled thermodynamic and geomechanical deformation analysis using TOUGH-FLAC simulator, and investigated the effectiveness of strain monitoring method in detecting mechanical failure of liners which may provide major pathways of air leakage. We therefore used an equivalent continuum model to relate the localized tangential strain to fracture permeability changes, which was developed in our early work (Rutqvist et al, 2012). In detecting and characterizing the leakage location, we tested a cross correlation technique using the synthetic pressure responses monitored in case of the failure of the inner liners. From the investigations, we showed that tangential strain, rather than radial, monitoring especially at the inner face of the sealing liners can be more effective in detecting the mechanical failure of the liners.In localizing the leakage point, we noted that the interface between the inner liners and surrounding rock may not be perfectly bonded so as to increase permeability through which any leaking air pressure may migrate more dominantly. We also demonstrated that the cross correlation of the time histories of pressure measurement especially at these interfaces can be useful in identifying the leakage point. These results may provide useful information in overall design of monitoring and alarming system of our upcoming CAES pilot facilities."

Jan 1, 2015

By Adrian White

Agenda Overview of pastefill at Kidd Mine Pipeline wear and the need to monitor Steel Loop monitoring Steel Borehole monitoring Monitoring pipe linings

May 1, 2013

By M. Moagabo

CO2 emissions from carbonate laden reclaimed mine spoil has been shown to pose a hazard to residents in homes built on or adjacent to such land. The objective of this project was to develop a soil CO2 flux survey protocol for assessing reclaimed mine land. The research involved CO2 chamber accumulation flux surveys; stable carbon isotope ratio analysis; statistical hypothesis testing to examine correlation between CO2 flux and soil temperature and moisture as well as spatial dependence; and geostatistics to map CO2 and delineate high flux zones. Soil temperature was observed to have a positive correlation with fluxes while soil moisture was observed to be negatively correlated. Spatial dependence of CO2 fluxes on reclaimed mine land was observed on one of the two study sites. The research suggests that macro-porosity and gas permeability may be important factors that explain CO2 migration in mine spoil. A flux survey protocol has been developed, based on these results, for reclaimed mine lands. The work demonstrates the capability of geostatistical methods to delineate high flux fields. Further research will be required to determine suitable thresholds for such analysis.

Jan 1, 2012

By Bruce Macdonald

Operational monitoring of slope stability can be achieved by space based InSAR monitoring platforms. Natural and man-made rock slopes are monitored using a novel stack-based InSAR method that exploits both persistent point scatterers (PS) as well as coherent distributed scatterers (DS) such as areas of pavement and sparsely vegetated surfaces. The new method, Homogenous Distributed Scatterer (HDS)-InSAR identifies InSAR targets by using adaptive multilooking of statistically homogenous pixel neighbourhoods combined with thresholding the differential temporal coherence of each target candidate with respect to its surroundings. HDS-InSAR preserves PS and therefore forms a direct generalization to our proven DualScale-PSI method. The density of HDS exceeds that of PS by more than an order of magnitude often providing essentially continuous coverage over urban and industrial landscapes featuring a mix of infrastructure with mostly bare soils or rock surfaces. The improved coverage enables better definition of surface motion and underlying geology, which will lead to superior interpretation of the geophysical mechanisms causing the surface deformation, e.g. through improved integration with 3D deformation modeling. We illustrate the performance of our new HDS-InSAR method compared to DualScale-PSI using displacement results from Vancouver, Canada; Bingham mine, USA; and the Palabora mine, South Africa.

Jun 1, 2012

By Antal Partos

ATLAS Processing Company Shrevesport, LA initiated a major plant expansion in 1980. SITE Engineers, Inc. provided engineering consultation regarding the foundation of the vacuum unit. Four test borings were drilled and laboratory testing completed for shear strength and compressibility. Vertical drains were proposed to accelerate time rates of settlements. Steel erection was completed by May 22, 1981 with very small < 0.1 in., settlements. Hydrotesting was initiated on July 9, 1981 and completed on August 27, 1981. An average rebound of 0.3 in. was computed resulting into an average net settlement of 0.5 in. This paper describes in detail soil behavior during load testing.

Jan 1, 1992

TRE ? worldwide leader in InSAR ? Spinoff of Polytechnic University of Milan ? Numerous patents for cutting edge technology (e.g. SqueeSAR?, PSInSAR?) ? Focus solely on InSAR with over 13 years experience ? ISO 9001 quality certification ? Powerful scalable parallel processor to handle all jobs What can InSAR provide for mining? An advanced suite of tools for monitoring ground deformation over mine sites: ? Deformation maps ? A dense network of measurement points ? Time series ? Cross sections of surface profile evolution

Aug 1, 2013

By John E. Rourke, O&apos

This paper describes some of the results of a project for the design and demonstration of subsidence monitoring systems for underground coal mines. The project was designed to test monitoring systems described in an earlier feasibility report (O&apos;Rourke and others, 1979). General objectives of the project were to develop reliable cost- effective monitoring systems for use above caving- type mining operations, over supported mines, and in urban undermined areas. Topics selected for discussion in this paper include a description of the instrumentation systems, the site conditions, problems of installation, resulting recommendations and an over- view of subsidence performance data obtained. There were some particularly difficult problems of installation to overcome at this site. Some of these could be experienced at any surface or under- ground project, others are probably more directly related to Western coal fields. Almost any subsidence monitoring program may face the following difficulties:

Jan 1, 1982