Search Documents

By I. James, R. J. Durrheim, M. S. D. Manzi, O. Valeshin, J. Lepine, L. V. Socco, C. Colombero, A. Malehmir, M. K. Rapetsoa, M. Sihoyiya

The FUTURE project aims to enhance seismic surveying in South African mining by integrating advanced acquisition technologies. In this paper, we detail surface and underground seismic surveys at the South Deep gold mine as part of the project. Surface seismic acquisition used co-located broadband micro-electromechanical sensors, one and three component recorders connected to geophones, distributed acoustic sensing using a straight fibre optic cable, along with a 6 ton broadband seismic vibrator operating with 4–180 Hz linear sweeps. In addition, underground surveys employed a combination of straight, and helically wound fibre optic cables, cabled-based and nodal sensors, along with a 500 kg drophammer mounted on a skid steer bobcat. The surface and underground seismic arrays were time synchronised using a GPS-time transmitter to allow for accurate seismic data recording in a GPS-denied environment. Results show the efficacy of these techniques in acquiring high-resolution seismic data, revealing detailed subsurface geological structures and mineralisation down to 3500 m below ground surface. Surface data revealed clear seismic reflections corresponding to the Black Reef and Ventersdorp Contact Reef. An underground P-wave velocity model exhibits low velocity anomalies that are associated with fracturing, while a P-wave reflection stack section shows significant reflections and a degree of faulting below the tunnel floor that was not observed on the surface reflection seismic data. We highlight the potential of these technologies to enhance safety, efficiency, and sustainability in mining. This study sets a benchmark for future reflection seismic surveys, paving the way for safer, more efficient, deep mineral exploration and extraction practices.

Jan 12, 2025

By R. N. Torbin

Foster-Miller has recently developed a new concept.for a highly specialized shaft lining system. This innovative shaft lining system uses a continuous slipforming placement technique. lining the shaft from the bottom up such as in a raised bored shaft. Although this part is not unique, the concept is designed to use polyurethane foam instead of concrete for the liner material. Furthermore, the concept is designed to attain rates of advance of 30 m/hr. The polyurethane foam liner is designed to be thinner (100 mm) than a conventional concrete liner (300 mm). It will eliminate the high cost associated with the erection and operation of an on-site concrete batch plant. The system will be designed to be operated remotely, requiring few personnel for its operation. This system (or parts of it) may be appropriate where fast construction speed is required or where a jointless liner is needed.

Jan 1, 1988

By Reinhard Gnilsen

Soil Nail walls, like any other structure, must meet high standards of design to be acceptable to the public and owners. On the other hand, the concept of soil nailing trails behind other structures in terms of defined design criteria that are commonly acknowledged. This is not to say that soil nail walls need to be less safe or less conservative than alternative more conventional concepts. Instead, the lack of established design criteria and design methodology entails that rules of thumb from past experience, overly simplified calculation assumptions, and the engineers' common sense judgement must substitute for a complex analysis of true stability and wall performance. Those "design approaches" must be conservative to ensure an adequate structure. Also, soil nailing may not be perceived prudent where site conditions are considered beyond past experience. For instance, site conditions may be perceived out-side the scope of soil nailing applicability where walls are very high, soil parameters variable or low, or nearby buildings close to the wall edge. The latter relates in particular to deep

Jan 1, 1988

By Vincent Tricot, Daniel Altier, Roger Storry

"INTRODUCTION The Liantang / Heung Yuen Wai Boundary Control Point (BCP) project, located in the north-east New Territories of Hong Kong, will form the seventh land crossing between the Hong Kong Special Administrative Region (HK) and Shenzhen in China (Figure 1). The BCP project comprises an 11km long dual two-lane trunk road linking the border crossing facility to the existing road infrastructure in HK and when completed it will facilitate future regional development and alleviate frequent traffic congestion at the existing Boarder control points.In December 2013 Dragages Hong Kong (a member of the Bouygues Construction Group) was awarded the 5.4km long Contract 2 section of the project, including the 4.8km long Lung Shan Tunnels, by the Civil Engineering and Development Department of the Government of the HK SAR. To overcome the difficult ground conditions anticipated along the Contract 2 section of the project the tunnels will be constructed using mechanical and drill and blast (D&B) excavation techniques together with a 14.1m diameter multi-mode Earth Pressure Balance Tunnel Boring Machine (TBM). Land constraints imposed on the project alignment require that the final 500m section at the northern end of the Lung Shan tunnels, under Princess Hill (Figure 2), takes an almost 90 degree turn towards the north. The resulting 354m radius curve restricts the sight-line of road users to below the minimum 110m at 80km/hr hence, the internal span of the tunnels needs to be increased from 12.6m, in the standard straight section, to 15.4m in this curved section to accommodate a widened shoulder which will provide the required sight-line distance."

Jan 1, 2016

By G. Cavanough, A. Torrance

Emulsions have been developed for over forty years to become the most common water-resistant explosives used in the mining industry. An emulsion is a common commodity, with many examples in our day to day lives of one immiscible liquid dispersed in another. They have varying degrees of stability from a few seconds to years. What makes their application in explosives unique is twofold. They contain a high concentration of salts in the dispersed phase and also have a far larger volume of dispersed phase than continuous phase. The continuous phase contains at least 75% by weight of an oxidizer such as ammonium nitrate dissolved in water. The crystallization point of these solutions is often >60oC which means that the formation of the emulsion has to occur at an elevated temperature. Once the emulsion is cooled, its structure helps to prevent the formation of crystals in an otherwise unstable system. At room temperature there is a considerable potential for the small oxidizer droplets to crystallize which is countered by the strength of the oil layer and also the size of the emulsion droplet. If the emulsion droplet is too large then crystals can form which may lead to rapid deterioration of the emulsion and overall crystallization, accompanied by a temperature rise as the heat of crystallization is released from the emulsion. The size of the emulsion droplet is critical in preventing crystal growth and subsequent droplet coalescence and emulsion break down. One method of examining emulsions and understanding their structure is to use optical microscopy to measure droplet size and also emulsion deterioration from shearing, temperature cycling and when contaminants are introduced, such as detergents, different oil types, coating agents and dust particles. This paper reports on advanced techniques to quickly assess emulsion quality and stability

Jan 1, 2024

Productivity and efficiency of diesel-powered underground trucks and LHDs can be enhanced through the application of a range of advanced technologies. In addition, these machines are subject to ever more stringent emissions control requirements. This paper will review how various technologies can improve usability, maintainability, and performance of LHDs, through a number of examples. The use of instrumentation and monitoring to understand the role of operator practice on mucking efficiency, as well as the use of finite-element analysis to evaluate structural design, and the use of control techniques to modify operator inputs and hence decrease power consumption, will be presented.

May 1, 2002

By Vince Newberry

Alcan Rolled Products at Oswego, New York, commissioned Recycle II during May of 1995. Recycle II is an advanced technology UBC recycling facility designed to meet the most stringent environmental standards enforced to date in the United States, particularly with respect to NO, and particulate emissions. This paper addresses the exacting requirements and strategies of Alcan's Recycle II project andThorpe Technologies' design considerations and solutions for the supply of environmentally favorable melting furnace and delacquering systems. The furnaces are equipped with low NOx regenerative burners and furnace pressure and hearth gas flow controls designed specifically for processing the hearth gases through baghouses. The delacquering system is a new generation Apros concurrent flow unit designed for low NOx emissions.

Jan 1, 1995

By D Xiong, G Xu, L Yao, F Wang, Y Duan

The goal of this project has been to digitise and use drill parameter data from rotary drilling (measurement while drilling; MWD) for a more effective planning of the blasting process in surface mines. A more accurate and reliable digital drilling and automatic hardness identification technology was developed, which includes both a hardware and software system. In the aspect of hardware, we designed a positioning, navigation and hardness perception terminal system which consists of a global positioning system original equipment manufacturer board, programmable logic controller and sensors of measuring major parameters, and a wireless data transmission system which combines digital blasting platform and wireless transmission facilities. In the aspect of software, we developed the navigation software of locating blastholes using LabVIEW and C++, and the blasthole design software using AutoCAD ActiveX (C#) technologies. This new technology is applied at Jiangxi Dexing Copper Mine, and initially realising the digitisation of drilling and hardness identification in blasting zone.CITATION:Duan, Y, Xiong, D, Yao, L, Wang, F and Xu, G, 2015. Advanced technology for setting out of blastholes and measurement while drilling, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 593–598 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

General recognition of the potential benefits of utilizing advanced technology has focussed public attention on the organisation of tertiary education. This has produced a situation where opportunities exist for significant changes to be implemented. The challenges to Mining education in this environment of change are analysed with respect to the setting of education objectives, the role of centres of education, course structures and student access to courses. The scope of the analysis includes formal courses for professional education and technical training, and programmes for continuing education and postgraduate research. Previous significant advances in mining technology illustrate the importance of encouraging the establishment of an extensive involvement with mining education. Education cannot be the sole responsibility of professional academic organizations; significant industry participation is essential. Methods of achieving this interaction are discussed. Major changes in techniques available for disseminating information provide a significant incentive to assess the relevance of existing course structures and restrictions on student access to courses. Establishment of a less rigidly progressive system of education is discussed with respect to the development of the full potential of computer based learning. This will expand the availability of mining education to include remote locations. The practical feasibility of such changes and recognition of the value of education as a commercial resource could also increase overseas involvement in Australian mining education. Benefits of such changes and problems that may develop if accreditation systems are not also changed to take account of new technology are outlined.

Jan 1, 1989

By V S. Mutton, M J. Shearer

"The current economic challenges faced by the mining industry led to a review of options for reducing the cost of ventilation control devices (VCDs). The VCDs at the Mount Isa Mines site operated by Glencore in Queensland typically experienced significant damage on the operating levels and required expensive replacements. Ventilation controls can become damaged by the effects of stope firings. This paper discusses the nature of blast wave effects, giving consideration to distance from the firing and changes in mine geometry. The time taken to adjust the airflow on the operating levels with the current VCDs resulted in the loss of productivity opportunities. The mine site engaged an equipment supplier to collaborate on the development of a high-strength regulator to control the required airflows within its underground workings.The strengthened regulator proved to be cost-effective and provided additional benefits, including ease of use, simplicity of installation and speed of change in the control of available ventilating airflow. An added advantage of the re-engineered regulator compared to contemporary VCDs is its flexibility, which includes the ability to easily move mobile equipment into different ventilation districts where required without the need to remove the VCD from its location. This paper describes both the innovation and environmental sustainability approaches followed when developing the new regulator for its implementation at the site.CITATION:Shearer, M J and Mutton, V S, 2015. Advanced ventilation control – an analysis of innovation and environmental sustainability, in Proceedings The Australian Mine Ventilation Conference, pp 55–62 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 31, 2015

By D. McCarthy

This paper discusses the process involved in developing an optimum method of treating and removing heavy metals from water that have leached out from the native rock -prior to discharge back into the environment. Also designed into the system is a manner to stabilize the metals removed as a precipitate, so that they can be disposed of as a non-hazardous waste.

Jan 1, 1992

By M. Fan, M. Mankosa, G. Luttrell

"Column and other non-conventional flotation approaches continue to provide benefits where conventional flotation processes have exhibited limited success. This is particularly evident with respect to flotation of ultrafine and coarse particles. Advancements in air sparging technology have provided the ability to produce finer bubbles than previously possible. The generation of finer bubbles coupled with the froth washing capabilities of a flotation column has demonstrated improvements in ultrafine particle recovery while simultaneously producing a high-grade float product. On the other side of the spectrum, the use of these sparging technologies while applying flotation fundamentals to a fluidized-bed reactor has increased the maximum floatable particle size up to and in excess of 3 mm. Benefits of higher recoveries and reduced reagent consumption have resulted from the use of these technologies. An additional benefit includes a reduction in plant grinding requirements. As such, this paper describes the application of Cavitation-Tube sparger technology and fluidized-bed flotation (HydroFloat). A review of data from industrial and pilot-scale applications is also provided.INTRODUCTIONConventional (mechanical) froth flotation is considered the workhorse of the minerals processing industry. This low-cost process makes it possible to selectively recover minerals by exploiting the difference in surface characteristics (e.g., wettability) of the valuable component and the waste material. Unfortunately, the upper particle size limit for flotation rarely exceeds 0.600 mm, and is typically maintained at less than 0.300 mm for most industrial applications. For many commercial base metal plants, the particle size range for optimum recovery is typically between 0.01 and 0.1 mm (Lynch et al., 1981). This finding is not novel. In fact, the effect of particle size on flotation recovery was studied as early as 1931 by Gaudin et al. who showed that coarse (+0.250 mm) and extremely fine particles (-0.010 mm) are more difficult to recover than particles of an intermediate size. The loss of recovery is due to inherent limitations associated with the flotation process, including bubble-particle adhesion and collision, detachment, buoyancy, and transport."

Jan 1, 2010

By L. Iacopetti, A. Calderara, M. Perego, P. Perrone, T. Furusawa

De Nora, a global leader in the development, manufacture and sale of all DSA® anodes based on titanium coated with mixed metal oxide (MMO) for electrochemical processes will present key advancements made to Self-Protected Anodes (SPA) for metal electrowinning. (DSA® is a registered trademark of Industrie De Nora S.p.A., Italy). In 2017 pre-commercial demonstration cells were operated in industrial environment. The program’s focus was to fully demonstrate the SPA anode’s superior mechanical and electrochemical robustness during normal and induced dendrite shorting occurrences while providing quality of plating in commercial operation. De Nora specialists focus on key components, in particular the engineering of the self-protection system, DSA® anodes and catalyst formulation capable to cope with high levels of pollutants while providing long service life in the meantime. Results of field trials confirmed the expected anode performance and enabled the selection of the most suitable “SPA” structure, based on resistive protective elements. Summarizing the economic benefits to copper electrowinning tankhouse operation with De Nora’s self- protected all DSA® anodes are; Double-digits power savings Cobalt-free electrolyte operations Minimal dendrite shorting damage incurred at the SPA anode Smoother, uniform cathode deposits with tangible improvement on current efficiency Tankhouse operations producing lead-free copper quality cathodes, in addition to elimination of lead waste for improved operator health and environment. INTRODUCTION De Nora’s engineered “Value Technology Package” (“VTP”) for electrowinning, consisting of our DSA® anodes coated with mixed metal oxide specifically formulated for copper electrowinning in conjunction with an advanced self-protected full titanium anode (“SPA”), underwent an intense field qualification program, inclusive of the behavior under massive short-circuits as part of the field investigation, with the goal to select and appoint the ultimate design configuration of “SPA”. Optimized wireless-based monitoring system was included in the field program, demonstrating good functionality for cell parameters monitoring and remote shorts detection.

Jan 1, 2019

By Shani Engelbrecht, Belinda McFadzean, Avuyile Wali, Natalie Shackleton, Vratislav Malysiak

Frothers play a crucial role in sulphide and PGM ore flotation recovery, and AECI Mining Chemicals studies on PGM ores have shown significant flotation kinetic increases with the optimal frother-collector combinations. Using Senfroth 200 as the industry baseline, remarkable kinetic increases were observed with AECI Mining Chemicals developed frothers in the first concentrate. Even in the worst-case scenarios, 4E PGM recovery increased by 5% at a slightly higher concentrate grade. It is important not to limit frother dosage to a fixed value. Instead, enough frother should be added to maintain a stable bench float, measuring the dosages by frother volume before and after tests. Frothers can be specialized blends and their importance should not be underestimated. The results produced by formulating and innovating frothers to address specific industry challenges have been encouraging. Testing a frother on a plant scale does not have to be as daunting as with collectors, enabling the identification of the best frother-collector combinations at an industrial scale. AECI Mining Chemicals bench scale testwork has motivated plant-scale trials that have successfully transitioned to commercialization. This paper compares the results from metallurgical and froth stability tests and shows that occasionally frothers that have a less stable froth can have improved valuable mineral recoveries, while still exhibiting better drainage for reduced entrainment and mass pull. It was shown that caution should be used when relying only on simplified froth stability tests in the evaluation of new frothers.

Feb 1, 2025

By Trevor Riters

Advancements in Emerson’s instrumentation technology have brought value and efficiencies to the mining industry. Some think of instrumentation as basic sensors and valves, but with our solutions, we equip operators with real time, accurate, and reliable data that they can use to operate more effectively. Working with Caltrol, an Emerson Impact Partner, we successfully engineered wireless skids for a leach pad to provide precise measurement and control of raffinate solution to many of the large mine sites in Arizona.

Feb 1, 2025

By David R. Hanson

Seismic tomographic imaging, based on the same principles as a medical CAT Scan (Computer-Aided-Tomography). has been used for many years in the oil industry for large-scale subsurface stratigraphic characterization. and has most recently been applied to various structure- and stress-related problems in the coal industry. New developments in signal processing have greatly enhanced the speed, resolution, and range of applications of topographic imaging in underground settings, and recent innovations in data acquisition hardware have further increased data reliability and repeatability. Whereas past structure mapping applications relied on Seismic velocity and/or attenuation tomopraphy within an enclosed seismic source gram receiver array, recent developments in "True Reflective Tomography- (TRT TM) have expanded the application of this technology considerably. For example, in-seam TRT TM seismic reflection tray now he used to image structure, and/or old workings from one general location in the mine face areas of mains and panel developments) well ahead of planned developments largely eliminating the need to probe-hole drill on regular intervals. This new reflective technology bas also been combined with traditional cross-hole seismic tomography-providing a comprehensive, powerful tool for velocity attenuation. and reflective imagine utilizing the same source/receiver array data sets (borehole-to-borehole. borehole-to-entry and entry-to-entry). These new developments in data acquisition and image processing have greatly expanded the variety of applications for tomographic site characterization allowing the mine operator considerable flexibility to cost-effectively characterize previously inaccessible areas of the property. This paper presents examples of 2-D and 3-D .seismic topographic imaging applied to (1) the location of old works in Appalachian room-and-pillar operations and (2) the identification of anomalous zones ahead of mining/tunneling developments these applications demonstrate the state-of-the-art in seismic ground imaging using velocity, attenuation. aril reflection techniques land combinations thereon, and further illustrate the flexibility of data acquisition from a variety of tinning arid tunneling settings. Recent examples are presented from projects in the United States and Europe.

Jan 1, 2000

By Shangyong Lin, Wei Sun, Weiping Liu, Muhammad Azam, Junfeng Cheng, Yujie Zhao, David Asubonteng, Michael Ngoie

Copper concentrates have wide application in global smelting operations, comprising primarily of chalcopyrite (CuFeS2) as the principal mineral, accompanied by chalcocite (Cu2S) and bornite (Cu5FeS4) as secondary copper-bearing minerals. However, these concentrates frequently harbor detrimental impurities, notably fluorine ions, which can cause various complications during the smelting process. Moreover, an elevated fluorine content in copper concentrates may entail financial penalties and sales constraints. This review conducts a comprehensive analysis of existing methods for the removal of fluorine, presenting a nuanced assessment of their merits and demerits. It also provides valuable insights into the current landscape of fluorine elimination from copper concentrates and pinpoints pivotal areas warranting future investigation. This review endeavors to serve as a pragmatic resource for researchers and industry professionals operating within this domain.

Jan 1, 2024

By M. Zaske, E. R. Mortensen

"As mine operators continuously look for ways to improve functionality and increase the capacity of their facilities, existing process equipment is often pushed to and past its designed limitations. As a result, equipment manufacturers are asked for economical solutions to meet redefined processing needs. Newmont Mining in Nevada was faced with such a need in its carbon-in-leach (CIL) train. In a collaborative effort between Newmont and Derrick Corp., tests were conceived to assess the viability of drop-in replacement screens using a three-dimensional screen panel. The synthetic pyramid screen panel was designed to increase flux while maintaining the existing equipment footprint. The test is the end result of an ongoing research and development project that Derrick undertook in an effort to refine and upgrade its urethane screening media. The application of this new screening media is presented for this CIL application along with future plans to implement the technology in trash, safety, carbon dewatering, carbon sizing and other scalping applications.In spring 2014, Process Machinery Associates (PMA), Derrick’s local area representative, met with Newmont to discuss the operation of the in tank screens in the CIL train at Twin Creeks, near Golconda, NV. The process was originally designed for about 12+ kt/d (13,000+ stpd) but the throughput has been steadily rising since the plant was commissioned. Newmont now requires 14.5 kt/d (16,000 stpd) to be processed. The original screens were running at their maximum capacity, and Newmont required additional screening capacity to continue the upward trend in production.Physical separation by use of screening is one of mineral processing’s oldest methods. Screening media can be prone to blinding and pegging, and the necessary support structures required for finer apertures result in smaller open areas. Therefore, more screening area generally requires larger panels and, thus, larger machines, screening media that does not blind or a combination of both.In an effort to avoid larger machines, Derrick had been working on a revolutionary threedimensional panel that would add nonblinding screen area in the same footprint of an existing machine. Alpha testing of the new screen panels began at Newmont Mill 2/5 in July of 2013. It was still occurring when PMA approached Twin Creeks about beta testing a refined machine and pyramid panel. After presenting the initial results, Twin Creeks determined that an upgraded machine and pyramid panels would be a possible solution to meet production needs. The testing of a machine eliminated the risk of capital costs to Newmont and provided Derrick the opportunity to obtain additional data."

Jan 1, 2015

By H Haghighi

Haul roads are often permanent unsealed access roads used by heavy haul trucks to transfer minerals. These roads can deteriorate rapidly which results in potholes, deformations and dust. Downer EDI Works has successfully provided efficient solutions to the mining industry to maintain their haul roads. HaulPac as a solution package is a process in which a bituminous emulsion is used to create a stable and durable pavement. The emulsion penetrates the road and binds the particles together, creating a stable base. It also seals the surface and prevents water from penetrating the underneath layers. Bituminous emulsion can increase the strength of the pavement material and decrease the road surface degradation which results in dust suppression. However, the everincreasing price of commodities, the necessity of reducing carbon emissions and the increasing use of autonomous haul trucks have made it vital to invest in novel maintenance solutions that can meet the needs of the mining industry in a cost-effective manner. This paper outlines the benefits of bituminous emulsion in terms of productivity, safety and environment followed by Downer’s approach to evaluate the suitability and to optimise the amount of product. The potential for changing the colour of the treated surface is explored and an initiative that incorporates end-of-life tyres of haul trucks into the pavement is introduced. And finally, an innovative method using artificial intelligence to estimate dust emission is presented.

Sep 18, 2023

By Lía Martínez, James J. LoCoco

Borehole geophysical logging has developed and improved many measurements for mining exploration in the past decade. Imaging tools such as the acoustic and optical televiewer are now being used to collect real time, high resolution, oriented fracture and bedding data. Drill holes 100’s of meters deep can be processed very quickly using automated structure picking software and borehole core samples can be digitally logged instead of using paper and pencil.

May 1, 2008