Search Documents

By K. Galos

The paper presents increasing importance of mineral secondary and waste raw materials in the minerals management in Poland. Definition of mineral secondary and waste raw materials is proposed, according to current Polish law. On this basis, sources of various types of mineral waste raw materials are analysed. The special attention is paid to the wastes from mining and processing, wastes from power plants, and wastes from steelworks and other smelters. Other types of waste and secondary materials, such as metallic containers, glass containers, batteries, metallic wastes and scraps, are also taken into account. Analysis of sources of such materials is shown together with the main directions of their economic use. Available sources of information on manufacture and use of the mentioned secondary and waste raw materials are also analysed. Finally, for a wide range of waste materials, their current and expected significance as substitutes for some industrial and construction minerals in Poland is given.

Jan 1, 2011

By Gregg E. Korbin, Patrick Hamilton

INTRODUCTION The Balsam Meadow Project, presently under construction for the Southern California Edison Company, is located approximately 55 miles northeast of Fresno, in the Sierra Nevada Mountains (Fig. 1). Major components of this project include an underground powerhouse for a 200 MW unit and a high pressure power tunnel/shaft. Site exploration [ ]

Jan 1, 1987

By D Reid

The engineering properties of soils and tailings often exhibit significant anisotropy. One area where this has been well documents is undrained shear strength. Materials sheared in directions close to the principal stress direction in situ, i.e. triaxial compression, typically exhibit higher undrained strengths than those sheared in other directions such as simple shear. Importantly, along the most common critical failure surfaces relevant to tailings stability, whether primarily through tailings or a critical foundation layer, saturated materials are generally much closer to the simple shear loading direction than triaxial compression. Therefore, testing undrained shear strength of tailings or foundation soils in triaxial compression is likely to result in overestimation of the relevant strengths for design. Although these issues have repeatedly documented in the geotechnical literature for over three decades, they are not appreciated sufficiently across our industry. In an attempt to address and highlight these issues, a review is carried out of historical reference to the importance of simple shear loading. Attention is then drawn to the techniques applied in three recent post-failure investigations, where simple shear testing was applied. Finally, some relevant laboratory test results from a recent project in which the author was involved are outlined.CITATION:Reid, D, 2018. Importance of the simple shear loading direction to the stability of tailings storage facilities, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 274–284 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By N. T. Rogers

An accepted statement of fact is that transportation next to agriculture is the second most important industry in the world. The transportation networks of the United States contributed immensely to the growth and prosperity of our nation. My objective is to make each and everyone here aware of the need for communication between geologists, mining engineers, purchasing agents and transportation managers. Only through a cooperative effort is it possible to reap the benefits of transportation in the industrial minerals field. Transportation is often thought of in terms of trucks, rail cars, barges, covered wagons or whatever. If this is your only exposure to the transportation industry then you probably spent most of your life in a cave.

Jan 1, 1989

By W. O. Macha

El presente texto señala la importancia del Sink and Float como método de concentración que facilita la explotación de minas de bajas leyes anteriormente desapercibidas en la industria minera. El estudio se divide en dos partes: la primera describe las generalidades de dicho método, mientras que la segunda muestra las pruebas metalúrgicas desarrollas con minerales de las minas "Casapalea", "San Cristóbal" , "Yauricocha" y "Tajo Abierto" de la Cerro de Paseo Co., así como las de "Austria Duvaz" "Victoria" y "Germania"de la "Negociación Minera y Metalúrgica Lizandro Proaño S . A . ", y la de "Sacracancha Gale". Como consecuencia de estas pruebas de Heavy Media, se encontró que el 75% de minerales tiene posibilidades de ser pre-concentrados por este método, asimismo la importancia del Sink and Float radica en el campo de los minerales usados corno relleno en las minas y de las abandonadas canchas.

Jul 20, 1960

By T. Lilley

The use of membranes in wastewater systems has increased rapidly in recent years. Microporous or semi-permeable barriers augment conventional chemical or biological processes to meet stringent treatment targets. These developments enable elegant solutions to wastewater discharge challenges and extend the scope of water recycle redressing the overall water balance and operational economics Wastewater treatment processes are discussed by reference to the spectrum of waterborne contaminants and the respective membrane separation capabilities. The role chemical pre-treatment to enable physical separation of metals with micro-filtration (MF) is described and how integration of MF with reverse osmosis (RO) is used to control a broader range of dissolved contaminants Membrane configurations are considered apropos function, operational economics and sustainability. These features are exemplified with case studies. Firstly, MF alone following chemical precipitation for the removal of heavy metals, then MF onto two stages RO of different configurations for TDS reduction and waste volume minimisation and finally an open channel RO alone for the reduction of inorganic COD from a leach stream.

Feb 27, 2013

By Sue Ritz

Gold extraction has relied on coconut carbon in adsorption circuits for several decades. IXOS®, invented by 6th Wave Innovations of Salt Lake City, Utah, is a new type of adsorbent that exceeds the selectivity of carbon and improves on the mechanical properties of other available resins. IXOS selectivity against copper cyanide complexes allows it to be used in circuits that currently struggle with copper contamination. IXOS potential to eliminate or reduce the application of SART technology will expand the opportunities to exploit more complex precious metals deposits. This paper will describe the technology behind IXOS molecular imprint, its comparison to carbon adsorption in the field, and the effect of efficiency on long-term recovery from heap leach METSIM simulation software.

By M. A. Giralico

Solvent Extraction (SX) technology has undergone significant refinements including outright process changes to achieve greater copper production rates with lower organic entrainment levels. LIGHTNIN has completed a detailed study aimed at improving on the conventional Holmes & Narver and Davy Power Gas type impeller designs1 by optimizing the mixing through the use of high efficiency pumper turbines instead of making system changes as others are doing. Since each individual installation requires a different design head and flow, LIGHTNIN has developed the R320 "family" of high efficiency, curved blade pumper turbines. These impellers are designed to maximize head and flow while reducing entrainment through lower power consumption, less shear generation and turbulence, elimination of air incorporation, production of the optimum droplet distribution, and lower tip speeds. These improvements also maintain the required mass transfer and copper recovery of the traditional impeller designs. The R320 impeller benefits have been quantified using Laser Doppler Velocimetry (LDV) and proven in multiple domestic and foreign installations at flow rates exceeding 15,000 GPM. Design comparisons of this improved impeller type versus traditional technology impellers in head, flow, power and entrainment are presented for review. In addition, the inherent benefits of axial flow, high efficiency impellers like the A3 1 0 and A6000 in auxiliary mix chambers will be discussed. The high flow, low shear characteristics of these patented impellers provide the necessary dispersion stability for mass transfer while speeding phase disengagement in the settlers due to low power and low shear input.

Jan 1, 1995

By A. Bruce Matthews

Of the many opportunities in the mining industry to invest funds to improve operations, there is always some limit in every company as to how much can be spent each year for the acquisition of capital assets. Generally, there are many more opportunities for investment than funds to make the investments. As such, one of management's goals is to select the most profitable of all the opportunities available. Each opportunity must be carefully analyzed for its potential percentage rate of return. This percentage return or return on investment concept is an accepted financial yardstick of business profit- ability. For today's mining engineers, this problem resolves itself in the job of determining how to in- vest most productively the cash that is flowing from their operations so that it will multiply in value. There are four basic types of capital investments: Strategic investments, such as selecting a plant site, are those that affect virtually all long-run plans of a company. Change in a company's product line and expansion of company facilities are two other types of capital investments.

Jan 3, 1963

By C. Stapel, P. D. Roberts, D. G. Jones, W. G. Macdonald, R. J. De Meijer

"Abstract-Measurement of natural radioactivity has been used in both a qualitative and a quantitative way in mineral exploration, particularly in the search for uranium. In the last five years, the Kernfysisch Versneller Instituut (KVI) and British Geological Survey (BGS) have designed, built and tested a new detector system that greatly improves quantitative applications in mineral exploration, especially on the seafloor and in the nearshore zone. The new system is an enhancement of an earlier BGS design. The major improvements comprise the use of a highly sensitive ?-ray detector, together with new data processing, from which concentrations of natural radionuclides may be deduced in real time. After laboratory analysis of samples, these concentrations can be converted into mineral percentages. Once the mineralogy of an area has been characterized, this conversion can also be done in real time.Thus far the system has mainly been used to map heavy-mineral concentrations in coastal subtidaland intertidal sediments. For such work the multi-sensor detector probe is towed on the seafloor and various parameters are recorded continuously. The probe contains, in addition to the gamma-ray detector, a water-pressure sensor (giving water depth) and an acoustic device to measure bottom roughness. The system, when used together with high-precision positioning systems such as D-GPS, enables the production of detailed maps of bathymetry, bottom roughness, and seafloor radioactivity or mineral distribution. These maps allow mineral concentrations to be readily correlated with seabed topography and sediment type. In the same way, ?-ray detectors could be used advantageously during dredging operations to provide on-line assessment of the mineral content of the dredged sediment as well as to guide the direction of dredging. Additionally, the same technique could be used to monitor the subsequent fate of a dredge spoil after dumping on the seafloor.Natural radioactivity arising from potassium and the thorium and uranium decay series has potential use for the fast and reliable assessment of siliciclastic and phosphatic impurities in limestones. Detection of such impurities may preclude the use of the limestone for chemical or cement production.Apart from its use in exploration, the technique has significant potential in mineral processing, particularly of heavy minerals. It can be applied as on-line quality control in dry and wet separation processes and for process control, by using decisions based on the results to control valves and other instrumentation. In addition, it can also be used in environmental monitoring of waste arising from mineral extraction and processing. In conclusion, the technique described has a diversity of applications in exploration, mining and mineral processing."

Jan 1, 1997

By C. Stapel, P. D. Roberts, D. G. Jones, W. G. Macdonald, R. J. De Meijer

"Measurement of natural radioactivity has been used in both a qualitative and a quantitative way in mineral exploration, particularly in the search for uranium. In the last ?ve years, the Kernfysisch Versneller Instituut (KVI) and British Geological Survey (BGS) have designed, built and tested a new detector system that greatly improves quantitative applications in mineral exploration, especially on the sea?oor and in the nearshore zone. The new system is an enhancement of an earlier BGS design. The major improvements comprise the use of a highly sensitive ?-ray detector, together with new data processing, from which concentrations of natural radio nuclides may be deduced in real time. After laboratory analysis of samples, these concentrations can be converted into mineral percentages. Once the mineralogy of an area has been characterized, this conversion can also be done in real time.Thus far the system has mainly been used to map heavy-mineral concentrations in coastal subtidal and intertidal sediments. For such work the multi-sensor detector probe is towed on the sea?oor and various parameters are recorded continuously. The probe contains, in addition to the gamma-ray detector, a water-pressure sensor (giving water depth) and an acoustic device to measure bottom roughness. The system, when used together with high-precision positioning systems such as D-GPS,enables the production of detailed maps of bathymetry, bottom roughness, and sea?oor radioactivity or mineral distribution. These maps allow mineral concentrations to be readily correlated with sea-bed topography and sediment type. In the same way, ?-ray detectors could be used advantageously during dredging operations to provide on-line assessment of the mineral content of the dredged sediment as well as to guide the direction of dredging. Additionally, the same technique could be used to monitor the subsequent fate of a dredge spoil after dumping on the sea?oor.Natural radioactivity arising from potassium and the thorium and uranium decay series has potential use for the fast and reliable assessment of siliciclastic and phosphatic impurities in limestones. Detection of such impurities may preclude the use of the limestone for chemical or cement production.Apart from its use in exploration, the technique has signi?cant potential in mineral processing, particularly of heavy minerals. It can be applied as on-line quality control in dry and wet separation processes and for process control, by using decisions based on the results to control valves and other instrumentation. In addition, it can also be used in environmental monitoring of waste arising from mineral extraction and processing. In conclusion, the technique described has a diversity of applications in exploration, mining and mineral processing."

Jan 1, 1997

By G. J. van der Linde

Foskor operates a mine in the Northern Province of the Republic of South Africa exploiting the igneous complex at Phalaborwa. It produces about 3 million tons of phosphate concentrate per year by means of froth flotation from 26 million tons of ore of which 16 million is mined and milled on site. The remaining 10 million tons originate at the Palabora Mining Company and is pumped as a slurry to Foskor. Two types of ore are mined and milled namely Foskorite and Pyroxenite. (The main mineral content of this ore is Apatite, Phlogopite and Diopside.) After three stages of crushing the ore is milled using 24 rod mills and 5 verti mills. The apatite is then recovered using four stages of froth flotation. The stocks of Foskorite ore are rapidly being depleted and the PMC tailings will also fall away by the year 2002 so that the whole mining operation will then be centered around the Pyroxenite ore. This will lead to substantial increases in production costs. The recoveries achieved in the flotation plant are largely dependent on the successful operation of the comminution section. Parts of this plant are now 35 years old and the advantages of re-engineering, new technology and automation can only be applied to a limited extent in an effort to reduce costs. It was then decided to investigate alternative milling methods, both wet and dry.

Jan 1, 1999

By L D. Lawrence, R S. Day, Gordon Coleman

Commercial emulsion explosives are typically characterized by their relatively high detonation velocities due to the intimacy of oxidizer and fuel and to their sensitization with glass microballoons. However, numerous blasting operations in softer, more porous rock formations are better fragmented with slower shooting explosives. Although mixtures of emulsions with large amounts of ANFO (60-80%) can considerably reduce the high velocities, little water resistance is achieved with low levels of emulsion blended with ANFO. "Water proof" blends containing typically 50 percent of emulsion become quite costly due to escalating powder factors in ANFO patterns. Blends of sensitized emulsions with 20-30 percent ANFO retain the high velocity characteristics of the emulsions as well as increased densities which can also adversely affect blasting results in softer rock formations. The introduction of a reliable and predictable on-site gassing process for sensitization and density control of repumpable emulsions, with or without added ANFO, offers the end user the option of supplying a final product more suited to his blasting needs. The capability to widely vary final product loading densities and consequently product detonation rates better tailors the final explosive to different rock characteristics. The beneficial advantages of this system in softer rock formations have been well documented. Overall comparison between these variable density products with typical repump emulsions containing solid density control will be reviewed. Besides the obvious cost advantages and safety advantages of these systems the end user is provided more definitive control of his blasting operation.

Jan 1, 1990

By C Deacon

It is common practice to include microspheres or similar density reducing agents in inherently insensitive water-based commercial explosives to achieve detonative sensitivity in the absence of chemical sensitisation. It has recently become possible to similarly include microspheres in LDAN (low density ammonium nitrate). Further to previous studies and publications to determine the benefits resulting from the use of microsphere enhanced LDAN technology in blasting, additional advantages are described in this document. These include range tests at independent testing facilities (Universal Tech Corporation û USA) which reflect results observed in the field, and support theoretical assumptions made when the products were introduced. Additionally, on-site studies in opencast pits using Heavy-ANFO blends incorporating modified LDAN, show that monetary savings can be realised through significant advantages gained in plant throughput and explosives use.

Jan 1, 1999

By Ron Frye, Carl Liibbe, Wayne Curtis, Julie Pecori, Dan Leach

Test work comparing the performance of a Low Density Porous Ammonium Nitrate Prill to regular Porous Ammonium Nitrate conducted in Pennsylvania and New York showed that less ammonium nitrate was required to perform the same work and that improved sensitization of an emulsion/ammonium nitrate blend reduced “orange fumes”. Fragmentation was similar in all tests with improved heave and throw experienced.

Jan 1, 1997

By R Araya, G Harbort, D R. Seaman, L Huynh, P D. Munro

In today’s operating environment many conventional cleaner circuits struggle to produce final grade concentrate with acceptable levels of non-sulfide gangue and/or penalty elements. This is primarily due to poor selectivity and the entrainment of gangue, and is further exacerbated by the processing of lower grade ores with more complex mineralogy that require finer grinding for liberation. In new concentrators, the standard approach to cleaner circuit design is to define the number of stages of mechanical cells required to achieve the desired concentrate grade. Residence time is the primary factor to size cells and to determine the number of cells required to attain target recovery. While it is required for recovery, a bank of mechanical cells is not the ideal solution to maximise concentrate grade. Relatively coarse bubble size means slow flotation of fines, requiring long residence times. The combination of long residence times and no froth washing means higher entrainment as the pulp becomes more barren and froth stability decreases down a bank.In recent years, the Jameson Cell technology has been retrofitted into a number of concentrators around the world to solve both cleaner circuit capacity and concentrate grade issues. Jameson Cells have been installed at the head of conventional cleaner circuits to produce final grade concentrate in a single step of flotation using a single cell (referred to here as ‘cleaner scalping’ duty). The experience gained from these installations has provided the platform for the design of improved and simpler cleaner circuits that will perform better and be more robust to operate. This paper analyses traditional cleaner circuit designs and explains the philosophy behind new hybrid cleaner circuits, which use Jameson Cells to produce final concentrate and mechanical cells for a ‘cleaner scavenger’ duty. The advantages of the new cleaner circuit design are demonstrated by a case study from an operating plant. Engineering studies show that the better metallurgical performance can be achieved with less equipment than conventional cleaning designs, reducing capital cost, operating cost, and with more than 30 per cent energy savings.Finally, the paper describes simple modifications to the standard laboratory flotation test procedures which accurately simulate this new cleaner circuit using routine equipment.CITATION:Huynh, L, Araya, R, Seaman, D R, Harbort, G and Munro, P D, 2014. Improved cleaner circuit design for better performance using the Jameson Cell, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 141–152 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By E. Wasmund

"Sandfire’s DeGrussa Copper-Gold operation in West Australia is a new high grade copper sulfide mine, which includes a 1.5 Mtpa concentrator which was completed in 2013.Early after commissioning, it was identified that the flotation capacity in the all-mechanical cleaner circuit was not sufficient. In order to improve recovery, the tail from the cleaner scavenger was sent back to feed the rougher scavengers. Test-work was done on-site to evaluate the possibility of using a flotation column as a pre-cleaner. A CavTube™ sparging system was selected, which is especially effective for fine ore particle flotation. Test-work was conducted at site using a 150 mm diameter unit, and then confirmed on a 500 mm diameter unit. A 4250 mm diameter full scale unit was installed in Q4 2014 and commissioned in Q1 2015. This unit gave some significant advantages including a reduction in re-grinding requirements, elimination of a circulating load and increase in the recovery of copper in the cleaner circuit and overall circuit.In this presentation, the benefits of columns and cavitation sparging for floating fine particles and rejecting fine entrained gangue will be explained. Also, the results from a lab unit and a pilot unit will be compared against the results of the full-scale unit. The paper will demonstrate the scalability of flotation columns, and which phenomena and scale-up criteria must be considered to be successful. Finally, some general observations will be made about the importance of columns in copper cleaning circuits.IntroductionSandfire Resources’ DeGrussa copper-gold concentrator is located approximately 900 km north-north-east of Perth in Western Australia. The project area landscape is scrubby mulga lands with few notable features. The climate is arid with high temperature and heavy summer downpours."

Jan 1, 2016

By Martin Plante, Denis Hamel, Marie-Pier Bédard, Jeff McLaughlin

"The results and methodology for the optimisation of the zinc flotation circuit at the Matagami Mill using the 6-Sigma methodology are shown in detail while only the base line and final results are presented for the copper circuit. As a result of the six sigma project, the zinc concentrate grade was improved by 2% and the zinc recovery by 3%, with reduced dosage of reagents while the copper concentrate was improved by 2.4%. The process variation in the zinc concentrate grade and recovery was also reduced by over 50%. The main factors contributing to the project success were identified to be improvement in the plant measurement systems, an internal benchmarking exercise and statistically designed laboratory and in plant tests to guide the process improvement. The annual value to Noranda resulting from this project has been estimated at approximately $5 million.INTRODUCTIONThe Matagami concentrator started ore processing from the new Bell- Allard deposit in July 1999. Concentrator performance (grade and recovery of zinc and copper concentrates) was highly variable and work was ongoing to fix the sources of variation. In the mean time, Noranda embarked on its 6-Sigma initiative across the company. The 6-Sigma DMAIC (Define, Measure, Analyse, Improve, Control) methodology was used in the two flotation circuits to reduce variation and improve performance. The statistical 6-Sigma methodology moves towards identifying and controlling critical process operating variables (the X' s) to achieve customerspecified performance (the Y's). The goal of the methodology is to describe a process in a numerical equation known as the transfer function, given as Y = f (XI, X2, X3.. .), where Y could be concentrate grade or recovery and examples of X's are reagent dosage, particle size, etc. With the transfer function, optimal operating conditions and control tolerances are established for the key X's to ensure the desired Y performance is obtained.Each phase of the 6-Sigma methodology is explained below with examples from the Matagami project."

Jan 1, 2001

By Jacob Grasmick, Bill Newns

Despite ongoing digitization and “hardware” technological advances, geotechnical uncertainty remains the most significant risk in underground and tunnel construction. And, whilst they are commonly held up as an example of the sophistication of the industry, the practice of drafting and using geotechnical baseline reports is subject to a wide range of influences, not all of which support good risk management. Uncertainties in predicting ground behavior, the gap between the pre-construction assumptions, and the systemic response to construction remains a significant technical and communication challenge. Accordingly, this paper presents a framework to quantify geotechnical uncertainty using geostatistics and translate these into practical tools for ground risk management throughout planning, procurement and construction. Adopting even some of the principles of this framework should provide improvements to contract risk management and should assist to minimize the potential for commercial losses.

Dec 1, 2022

By Eugene Jak

Copper sulphide processing technologies face increasing pressures associated with decreasing concentrate grade leading to increasing thermal inefficiency and lower productivity. Impurity concentrations are on average increasing, creating potential environmental risk and additional treatment costs. In copper flash smelters dust, partially oxidised materials and fume formed from the condensation of volatile impurities, are routinely recycled to the feed. In the converting stage the heat balance is maintained by charging anode reverts and other inert materials. In both cases, the thermal energy available from sulphide oxidation is not fully utilised or optimised. The productivities of both smelter and converter stages can be potentially increased through the addition of a high copper, low iron, low impurity precipitated copper product. Calculations are carried out for fayalite smelter and calcium ferrite converter slags using an optimised FactSage thermodynamic database. The potential for significant increases in smelter and converter productivities using existing technologies are predicted.