Search Documents

By Takashi Nakamura

Dismantling and detachment of parts from e-scrap are essential and involve higher cost techniques in pretreatment processes for physical separation. New techniques are desired for effective recycling of minor rare metals, therefore, we are trying to develop new detachment processes such as a new break down process. The principal of this new process is an electrical disintegration by electric pulse. E-scrap is broken down by high voltage electric pulses in water. IC chips and LSI can be detached from printed circuit boards under proper conditions. Ta- capacitors are also broken down to plastic parts and Ta sinter with lead wire. This is very useful in terms of pretreatment for e-scrap recycling. Also in the case of metallurgical production, with its intrinsic potential of smelting, extraction, enrichment and separation methods, play an important role in the context of minor rare metals.

Jan 1, 2015

By P J. Chapman

Recent catastrophic failures of tailings storage facilities (TSFs) continue to highlight the need for a detailed understanding of failure modes and the defences that are in place within the design to mitigate the failure modes. However, in many cases the instrumentation devices and monitoring approaches selected during operation do not link back to the design defences and inappropriate or redundant instrumentation is often installed. Candidate instruments and monitoring approaches (critical controls) are presented and matched to critical failure modes, with clear linkages to the intent of each instrument/monitoring approach. Commentary on where complementary measurements with independent technology types are recommended to provide greater assurance of trends to the design engineer or TSF owner is also presented. In response to the recent TSF failures, an increasing focus is being placed on instrumentation and monitoring relating to slope instability and safeguarding against the potential for static liquefaction, using a critical state soil mechanics framework. To support selection of appropriate zoning within a stability model, three complementary devices are recommended – vibrating wire piezometers to provide an indication of pore pressure and allow the phreatic surface to be inferred, tensiometers to confirm the presence of unsaturated conditions (and hence low potential for undrained failure) and moisture content sensors to provide an indication of void ratio, and hence state parameter, in saturated zones. The combination of VWPs and tensiometers will provide complementary measurements in the saturated and unsaturated zones, and also provide information on the extent of any near-saturated zones, provided that sufficient instruments are installed.

Jul 1, 2021

By S. Foged

Umicore and MWH jointly demonstrated that mechanical dewatering of goethite and neutralised tailings significantly increased the life of a 30 ha tailings pond and improved the operation of the pond. Umicore operates one of its zinc production plants in Balen, Belgium. As part of its production process, an excess of neutralised and goethite¬containing tailings is generated. These have historically been stored inside large lined ponds. As the storage area of the current goethite pond was nearing its capacity, Umicore studied the potential for an extension to the existing embankment. However, this extension would face intense regulatory scrutiny, because the environmental and safety impacts were considered important. Together with Umicore, MWH suggested and investigated an alternative treatment approach consisting of mechanical dewatering prior to storage. A feasibility study was prepared where wet storage was compared to dry storage. Differences in safety risks, environmental impacts and economic costs were outlined. The study demonstrated that the life of the tailings pond could be increased from 6 to 22 years, seriously reducing the environmental impacts and safety risks at no significantly higher cost than would have been incurred with the continued operation of the existing pond. The results of the study are presented in this paper.

Jan 1, 2006

By M S. Powell, M P. Bueno

The commonly used SAB, SABC and run-of-mine (ROM) ball mill circuits can achieve high throughputs with good operating stability. However, these circuits consume a substantial amount of grinding media, which can have a substantial impact on the OPEX and the æcarbon footprintÆ, specifically when viewed as an æembodiedÆ energy input. On the other hand, fully autogenous (AG) circuits can operate at much lower operating costs, but with limited throughput. The control of AG mills, fed by ores with hard and soft components, can also be challenging, due to the sensitivity of the mill to the ratio of hard to soft components.In this paper, a multi-component modelling approach was used to demonstrate that the harder component should be used as grinding media, and its use should be kept to a minimum to avoid reduction in the mill throughput. There is an optimal blend of hard to soft, and any optimal blending condition is both ore-dependent and mill-specific. Establishing this blend is challenging, and consequently discourages the use of autogenous mills. The new modelling approach addresses this challenge by providing a quantitative prediction of the influence of blending soft and hard components in a mill. This prediction can then be used to establish the required blend for maintaining a stable and efficient operation in autogenous grinding mode.CITATION:Bueno, M P and Powell, M S, 2012. How to use hard ore components as grinding media, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 31-36 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

By Gordon R. Haworth

Conditions affecting minerals investments are continuing to change at an increasing rate, and in this paper we will attempt to predict the course of mine financing in the future. We will first review the situation historically and then examine the problems and constraints that are now making the financing task more difficult. Suggested solutions are discussed, and a new method of financing a group of mining projects is hypothesized.

Jan 1, 1977

By M. Saghaeian, R. Hejazi, L. Hosseini, M. V. Sheikhzadeh

HPGR equipment has been well proven to be energy-efficient in the first stage of grinding in iron ore beneficiation plants. Numerous advantages of utilising HPGR grinding prior to ball mill grinding, such as reducing the power consumption in a ball mill through generation of micro-cracks, has been thoroughly studied. Less attention has been paid to efficiency of the HPGR circuit rather than the downstream ball mill circuit. In this study the HPGR circuit has been optimised through feed size reduction by crushing, and feed iron content upgrading by dry cobbing. This optimisation leads to better operation of the HPGR, and a smaller product size which is expected to result in a lower wear rate of ball mill liners and balls. It is also expected that the top size of the ball mill balls be reduced. Additionally, by reducing the feed size of HPGR from 30 mm to 15 mm, it is possible to achieve similar K80 of HPGR product in lowered pressure, i.e. 2.5 N.mm-2 instead of 3.5 N.mm-2 which translates to ease of operation. Similarly in a given roll pressure, smaller feed sizes result in higher specific throughput of ~10% which means higher production capacities. The results also reveal that this optimisation increases the concentrate weight recovery by about 10%. It also results in slight increases in the Fe grade of the product iron concentrate. Keywords: HPGR, HPGR circuit optimisation, crushing prior to HPGR, dry cobbing prior to HPGR, ease of operation, concentrate grade optimisation, weight recovery optimisation

Jan 1, 2020

High-pressure grinding rolls (HPGR) are an accepted, but continuously expanding, comminution technology. The copper industry has a growing need to process harder ores with progressively lower grades, more challenging metallurgy and increasing demand for efficient bacterial leaching applications. This has resulted in a major focus on HPGR use in a crushing circuit. If the industry is to increase leach extraction while lowering energy costs in high-throughput hydrometallurgical operations, HPGR will be of inherent significance. The following paper summarizes test work on copper leach ores utilizing the benefits of HPGR comminution, while increasing several critical metallurgical parameters. Based on the current work and previous investigations, it was found that HPGR comminution within a crushing circuit, in specific instances, can result in 2 - >10% increases in cop-per extraction. The tested variables are crush size, rock type and copper mineralogy dependence. Various other process parameters may also be optimized.

Jan 1, 2011

By C. T. Morley

The steadily increasing interest in high pressure grinding rolls (HPGR) as a legitimate alternative comminution technology for hard rock applications has led to a proportional increase in the demand for trade-off studies comparing HPGR with more established approaches, typically SAG-based but including AG and stage-crushing designs. The primary trade-off is between a) the higher capital cost typically incurred with HPGR-based designs and b) the higher operating costs of the more traditional technologies. However, if, through circuit design innovation, the capital cost penalty of HPGR circuits could be eliminated or reversed, then the need for trade-off studies would diminish.

Jan 1, 2012

By E Nunes, R Mendes, D Jacobson, G Cota, T Machado, E Santos, J Almeida, E Pereira9, B Raso

Grinding circuits are known to be the highest consumer of energy used in the ore comminution process, with high operational costs and sensitivity to ore conditions. The mining industry is being encouraged to look for more energy efficient processes while increasing the mass and metallurgical recovery; a specific example is projects with lower iron ore grades, which demands a higher level of liberation and resulting higher energy consumption. This has led to increased usage of high-pressure grinding roll (HPGR) technology as an alternative design within the comminution circuit. A growing use of the HRC™ HPGR technology has been used to generate concentrate through a more sustainable process. In the Brazilian state of Minas Gerais, the readaptation of iron ore beneficiation circuits has been initiated, replacing the traditional crushing-to-grinding flow sheet with circuits using crushing-to-HPGR flow sheets, with the main driver being reduced energy consumption. Utilising results from sampling campaigns and analysis of experimental data collected in an industrial plant, the work herein presents a case study from the JMN Mineração operating plant, where the HRC™ HPGR was used as an alternative to traditional grinding using horizontal mills. The results show that the HRC™ HPGR performance in this iron ore processing plant showed benefits in terms of reduced energy consumption as compared to the projected performance with a traditional grinding circuit.

Sep 18, 2023

By Ventsislav Stoilov, Angel Angelov, Ivan Korolev, Antti Remes, Todor Pukov, Stoyan Gaydardzhiev

"The process modeling and simulation studies aim for better process operation and favorable environmental impact. The objective of this work is to set up a simulation model of the Assarel copper flotation circuit for planning and optimization of the process with the aim of increased metal recovery. The model is parameterized based on laboratory flotation tests of ore samples from the Assarel mine together with mineralogical studies by X-ray diffraction (XRD) and Mineral Liberation Analysis (MLA). A combination of several techniques allows reliable identification of mineralogical composition of the selected samples. The changes in the proportion between sulfide minerals in various products along the circuit have been also documented. Further, this information is used in the simulation model and in data reconciliation procedures for establishing mass balance. The simulation accuracy is studied by comparing the simulations with the plant survey based mass balance. Constructed simulation model can be used to run alternative process scenarios. As an example, the flotation circuit performance with different reagent regimes is simulated based on data from batch flotation tests. Two reagents were considered for this purpose, dithiocarbamate-based one and xanthogen formate/mercaptan blend. It has been revealed that these reagents do not have the same influence on the selective flotation. The one improves flotation of gold and overall recovery but without notable selective action. In contrast, the other showed better selectivity towards copper, rejecting more gangue and lowering gold recovery. The model is also applicable for process optimization studies with different feed compositions, flowrates and circuit configurations. INTRODUCTION In the pursuit for elevated technological indicators, finding an optimal set of process parameters fully utilizing the potential of the equipment is a key factor to success. Over the past decades, there has been a substantial development in flotation circuit optimization through performance benchmarking using metallurgical modelling and steady-state computer simulation. Practical simulation engineering tools are based on experimental data obtained from laboratory tests and from plant surveys and operation data. With the help of flotation models, it is possible to study grade-recovery response with different feed compositions and throughputs, and with various cell-operating parameters, as well as to evaluate and design different flowsheet configurations. Outotec’s HSC Chemistry® software, which incorporates simulation and mass balancing modules alongside with several other tools, can assist with this optimization (Mattsson et al., 2015)."

Jan 1, 2018

By Dave P. DeClerck

Hardman Construction was faced with the challenge of completing a large earth retention project on a constricted downtown Detroit site, while maintaining a safe and productive worksite. To do so, new technologies using robotic equipment was instituted. HISTORY The historic J.L. Hudson Building (Hudson’s) in Detroit, Michigan was the premier retailer in the city’s downtown district from the 1890s through the 1960s. The massive flagship store sat at 1206 Woodward Avenue, one of the busiest streets in the Detroit area. Hudson’s broke ground in 1891 and would go through twelve renovations and expansions. The last renovations took place in 1946, which gave the building the title of being the largest department store in the world at the time. It spanned an entire city block and boasted 2.2 million square feet of retail space. By the 1970s, Detroit was in an economic downturn. The Hudson’s department store finally closed its doors in 1983. Besides a few working offices, the building sat vacant. The building was unique in that it had four levels underground, offices, mechanical areas, and equipment storage. Following years of neglect, the Hudson’s building was seized by the state and transferred into the hands of the city. The city had it demolished in 1998, (shown in Fig. 1) to construct a new, four- level underground parking garage as well as a potential future above-grade development (Sewlck, 2017). The building was imploded in one of the largest implosions of that time. The building rubble filled the underground rooms and helped to stabilize the exterior concrete walls and keep them from collapsing.

Jan 1, 2019

By A. Yaghini, Y. Pourrahimian

"Human factors (HFs) play an important role in the mining and mineral industry, affecting operational and maintenance efficiency and safety. Despite the introduction of new technologies and automation in this sector, it is well known that a significantly large proportion of total human errors occur during the operation and maintenance phase. A comprehensive literature review of HFs across several industries is provided. From this review, the impact of HFs on operation and maintenance is summarized, with a focus on what the mining industry is currently doing and what opportunities exist for additional improvements. Future research directions and themes are also identified.RÉSUMÉ Les facteurs humains (FH) jouent un rôle important dans l’industrie des mines et des minéraux, en ce qu’ils affectent l’efficacité et la sécurité de l’exploitation et de l’entretien. Malgré l’apparition de nouvelles technologies et de l’automatisation dans ce secteur, il est bien connu qu’une grande partie des erreurs humaines (EH) se produisent durant une phase d’exploitation et d’entretien. Cet article propose une analyse documentaire approfondie des FH dans plusieurs secteurs. L’impact des FH sur l’exploitation et l’entretien est résumé à partir de cette analyse, une attention particulière étant accordée à l’évolution de l’industrie minière et aux possibilités d’améliorer davantage ses activités. Sont également identifiés les futurs thèmes et voies de recherche.INTRODUCTIONDuring the past several decades, the mining industry has focused on improving equipment, machinery, and methods that have led to more advanced hardware and software, equipment with higher reliability and productivity, and other technological advancements. These actions have improved safety and productivity and have reduced casualties and maintenance workload. Although today’s mining equipment and machinery are technologically advanced and highly reliable, the risk of accidents is still relatively high and key performance indicators have not improved significantly compared to other industries (Sorensen, 2012). A prominent reason could be due to insignificant integration of human factors (HFs) as part of planning, operation, and maintenance activities. The current mining system is a people system, and inevitably HFs and human error (HE) figure prominently in all aspects of this industry. Even the most advanced technologies and innovations require operators and maintainers with significant knowledge and skill, which could increase the potential for HE."

Jan 1, 2018

By Charlotte Abena Benyarku, Albert Buabeng, Eric Stemn

The abstract highlights the increasing use of mobile equipment in mining and its contribution to accidents. The research analyzes injury narratives from Ghanaian surface gold mines to understand the involvement of mobile mining equipment in injuries and explore the use of injury narrative data as a human factors tool. The study identified priority human factor issues, such as operating mobile mining equipment, part removal/installation, and the operator's cabin. The use of Sankey diagrams for multivariable analysis effectively identified specific operator-centered issues that warrant further investigation for improved safety interventions.

Mar 29, 2022

By Jenifer S. Heath

Human health risk assessments can be used in mine permitting, and are frequently used to investigate areas of potential contamination and as a basis for remediation decision making. While some states and US Environmental Protection Agency (USEPA) Regions have their own guidance for the conduct of human health risk assessments, USEPA Headquarters guidance and the underlying science are changing and advancing rapidly. Even outside the US, USEPA guidance can affect risk assessment costs and conclusions, which in turn can affect cleanup costs or permitting options. This paper summarizes recent USEPA guidance and scientific evidence related to human health risk assessment for mining sites. This paper is designed for non-risk assessors, and so focuses on the potential applications and implications of the new guidance rather than the mathematical and theoretical details.

Jan 1, 1999

Grey River Gold Mining Limited (GRGML) has constructed and largely completed the commissioning of an alluvial gold dredge designed to recover gold from a low grade gold deposit in the Grey River Valley, New Zealand. The most important resource that GRGML has are the people who are employed by the organisation. The low grade of the deposit necessitates the requirement to operate the dredge at optimum efficiency, which in turn requires the work force to be of high calibre and continually motivated. The primary prerequisite for employment at GRGML is for employees to be receptive to new ideas and have the adaptability to develop new skills and apply those skills to the changing demands of the workplace.   A continually changing organisational structure is utilised to meet the needs of a changing work environment. The adoption of an innovative site employment agreement allowing for flexible working hours has aided the achievement of good employee productivity and attendance.   Employees gain a higher quality of life by working a roster pattern involving twelve hour shifts and a four day on, four day off pattern.   Employees and management are communicating very well and working together to achieve organisational goals which will ultimately benefit the employees, the shareholders, the local community and the mining industry generally.

Jan 1, 1989

By C. Eddine

"Can we use data to make communication effective? How does one successfully tackle the challenge of solving cultural differences and harmonizing the needs of diverse stakeholders while developing and maintaining a strong and reliable corporate image? Is it possible to achieve better engagement and minimizing risks with data? This paper aims to explore human rights and business procedures, the promotion of shared prosperity in a sustainable manner and the use of metrics to guide decision-making process. Among the topics examined are: • the significance of stakeholder engagement in community development projects; • the use of grievance mechanisms to give a voice to First Nations and communities / populations in vulnerable positions (including children and elders); • the benefits of configuring and implementing a feedback system in partnership with the communities. This research is a preliminary initiative and has limitations on the extent of the material used. The author acknowledges there is a vast amount of work and publications available on this subject, as well, as a variety of examples that have not been included. The intention is to keep developing this research to assess and expand how data can be used to minimize risks and improve engagement, in addition to inspire others to continue advancing this topic. Natural resources consumption is a reality that will not disappear in a foreseeable future. Several developments and operations are located in remote areas where communities in vulnerable situation and Indigenous Peoples live. Feedback systems are being ratified as a tool to help tackling the challenges of harmonizing cultural differences and fulfilling the needs of diverse stakeholders. Integrating social, environmental, and economic values plays an imperative purpose in preserving a productive and trustworthy relationship with stakeholders. Positioning social standards next to environmental and economic principles shows inclusiveness and firm intention of integration. We add value to a positive image of our industry by embracing responsibility for corporate actions and promoting their beneficial impact on the environment. The social context within communities, groups and organizations is dynamic and presents new challenges as connections evolve. There are wildly diverse expectations which one may need to address during exploration, construction and operating phases. Disagreements are an inevitable consequence of interactions due to the different needs and requirements of the parts involved. Nevertheless, balancing differences and solving conflicts can offer remarkable opportunities for improvement."

Jan 1, 2016

By Chen Feng

Compared to widespread successful deployment of robotic manipulators for repetitive and hazardous tasks in related industries such as manufacturing, the construction industry has achieved relatively limited benefits from robotics and soft automation. Unlike manufacturing, where robotic solutions benefit from the structured layout of the environment (e.g., factory assembly line), construction robots face unique challenges that arise from the rugged, dynamic, and unstructured environment of the work site, as well as the uncertainty and evolving sequence of occurring on-site events. This challenges any intended construction robots to not only replicate basic human motion, but also be capable of sensing and adapting to environmental changes, and making decisions based on the evolving state of the environment. Building upon recent advancements in robotic mapping, computer vision, and object recognition, the authors propose to introduce autonomous behavior at the basic task level for on-site construction robots to address these challenges in a flexible and extensible manner. This paper reports the outcome of the first phase of this research - a structured methodology for improved design and development of basic task automations - and focuses on algorithms developed for mobile robot navigation and relative pose estimation. The algorithms are implemented on a prototype mobile robotic platform, and evaluated in several experimental scenarios.

Aug 1, 2013

By Robin Burgess-Limerick

The introduction of automation to mining has great potential to reduce safety and health risks by removing people from hazardous situations. However, automation changes the tasks performed by people and may introduce new tasks. For the system to function optimally, these tasks must be designed taking human abilities and limitations into account. Humansystems integration refers to systems engineering processes that ensure that human-related issues are adequately considered during system planning, design, development, and evaluation. During procurement of automated systems, a human-systems integration program plan should be prepared that describes the human-systems integration activities that will be performed to address each of the six core domains of human-systems integration: staffing, personnel, training, human factors engineering, safety, and health.

Jun 16, 2020

HW Process Technologies, Inc. (HWPT) has developed a patented membrane-based ion fractionation system, which specifically separates copper from gold and silver species in a cyanide matrix. This Engineered Membrane Separation (EMS?) system was pilot demonstrated on the 82,000 liters of pregnant leach solution' (PLS) generated from tailings, via thin layer leaching, at a mine site in Durango State, Mexico. The EMS? recovered ~90% of the gold-silver cyano-complex to a 90% volume permeate (based upon an EMS? feed stream of 100% volume) while rejecting -90% of the copper cyano-complex to a \0% (by volume) concentrate. The EMS? technology combines pore-size specific electro-statically charged membranes with engineered materials of construction and application-specific operational design that reject multi-valent, ionically charged species to the concentrate and transmit mono-valent species through the membrane to the permeate. The 850 ppm Cu PLS contained approximately 0.8 gil free NaCN with, the copper cyano-omplex principally in the CU(CN)3 and CU(CN)4 forms. The gold grade of the PLS was -2 ppm Au. The ~LS calcium concentration at -700 ppm Ca was reduced to ISO ppm.Ca (± 50 ppm) by sodium cycle ion exchange pre-treatrnent prior to EMS? processing.

Jan 1, 1998

By Nick Vayenas, Ming Cai, Hongbin Zhang Lorrie Fava, Enrique Acuña

"A hybrid methodology is proposed to improve the accuracy of Diesel Particulate Matter (DPM) concentrations simulated in a ventilation network model by using Computational Fluid Dynamics (CFD). DPM, as a primary concern for underground hard-rock mines, has been studied in two dominant numerical models, ventilation network solvers and computational fluid dynamics. Ventilation network solvers are efficient, but they are not able to provide three-dimensional DPM concentration contours and only accept area-average DPM data as input. CFD simulations are time-consuming, but generating DPM concentration results with high accuracy. Besides, both monitoring points and planes can be created in a CFD model, which can take both point data and area-average DPM data as input. The hybrid methodology is intended to combine the advantages of the two by using the CFD results to update the network model results at key locations. A field study was conducted in a dead-end heading in an underground gold mine in the United States. Real-time DPM monitors were used to collect data. A CFD model and a network model were built for the experiment area. The CFD model was calibrated to the experimental data. In the study presented here, results from a calibrated CFD model are converted to equivalent diesel emission rates in the ventilation network model at a shared outlet. The hybrid methodology is used to provide better input for the network model. INTRODUCTION Mine ventilation system is one of the most important parts for an underground mine. It not only provides fresh air to the personnel but also helps clear the contaminants generated from the diesel-powered equipment. For most underground metal and non-metal mines, diesel particulate matter is the main contaminant. It is also the focus of this paper."

Jan 1, 2019