Search Documents

By M. R. MacIver, M. Pawlik, H. Alizadeh

Treatment of tailings is an integral component of mineral processing. Tailings with a high clay content are a challenge for the mineral processing industry; e.g. the clay slimes produced from production of phosphate in the mid-western United States and the fine tailings produced from oil sands production in western Canada. Dispersants are a commonly used process aid, but their impact on the structure and settling properties of high clay content tailings is not well understood. The paper describes the changes in composition and bitumen release that occur when mature fine tailings (MFT) are treated with a polymeric dispersant (lignosulfonate.) Synchrotron-source computed tomography (CT) was used to obtain high-resolution 3D images of samples prepared at varying dosages of dispersant. The CT method permits a powerful visualisation of the internal structure and composition of the samples. These insights will enhance our understanding of the structural characteristics of mineral tailings relevant to solid-liquid separation by flocculation and thickening. Keywords: Dewatering, dispersion, dispersants, chemical treatment, computed tomography

Jan 1, 2020

By A. Ansari

Standard depressants used in the selective separation of copper and molybdenum sulfides by flotation pose environmental and health hazards. In this investigation, the floatability of chalcopyrite and molybdenite in the presence of six well-characterized lignosulfonates was studied through Hallimond tube flotation and adsorption tests. The results define the physicochemical conditions (lignosulfonate type and dosage, pH, presence of ions) for possible selective separation of molybdenite from chalcopyrite. Dissolved polyvalent cations, especially calcium, appear to serve as "activators" for lignosulfonate adsorption on both minerals. From this point of view, the use of lime as a pH modifier is not always appropriate for optimum selectivity since high dosages of lime to produce high pH tend to indiscriminately depress both sulfides.

Jan 1, 2006

By N Gruber

In the continuous casting of ultralow carbon (ULC) steels, free carbon is used to control the melting behaviour of mould powders. If the carbon is not completely removed during melting, it is enriched at the top of the slag pool. Liquid steel may come into contact with this layer because of the turbulence of the molten metal, resulting in its recarburisation, which negatively affects the desired product quality. Thus, a reduction in carbon input is desirable. For this purpose, SiC and/or Si3N4 with and without antioxidants were selected as melt-control additives to replace carbon in the mould powders. Thermodynamic calculations were performed to quantify their effect on the melting behaviour based on the chemical composition of a flux already applied to ULC steels. To experimentally assess the liquefaction behaviour, laboratory mould powders were prepared and annealed in steel crucibles closed with a lid. Crucibles were inserted into a furnace that was already preheated to selected temperatures between 900–1200°C for 10 mins and quenched to room temperature. Subsequently, the samples were mineralogically investigated. The results confirmed those obtained from the thermodynamic calculations. Si3N4, and SiC in particular, are suitable raw materials for delaying the solid-solid reactions of raw material components during melting. Owing to their stability at high temperatures, the necessary SiO2 content to form a liquid phase is not available, resulting in lower amounts of the liquid phase. The addition of antioxidants to delay the oxidation of SiC further reduces this positive effect. Attempts to decrease the SiC content without negatively affecting the melting behaviour resulted in a reduction in the CO2 emission by at least 27 g CO2/kg of mould powder when compared to the carbon-containing standard mould powder. These investigations revealed differences in the melting behaviours of granules and loose powders, which are related to their respective production processes.

Jun 19, 2024

By Peter Zhang, Todd Minoski, Mark Van Dyke, Daniel W. H. Su

"This paper presents the results of a 2017 study conducted by the National Institute for Occupational Safety and Health (NIOSH), Pittsburgh Mining Research Division (PMRD), to evaluate the effects of longwall-induced subsurface deformations within a longwall abutment pillar under deep cover. The 2017 study was conducted in a southwestern Pennsylvania coal mine, which extracts 1,500-foot-wide longwall panels under 1,185 feet of cover. One 650-foot-deep, in-place inclinometer monitoring well was drilled and installed over a 150-foot by 275-foot center abutment pillar. In addition to the monitoring well, surface subsidence measurements and underground coal pillar pressure measurements were conducted as the 1,500-foot-wide longwall panel on the south side of the abutment pillar was being mined.Prior to the first longwall excavation, a number of simulations using FLAC3D™ (Itasca, 2017) were conducted to estimate surface subsidence, increases in underground coal pillar pressure, and subsurface horizontal displacements in the monitoring well. Comparisons of the pre-mining FLAC3D simulation results and the surface, subsurface, and underground instrumentation results show that the measured in-place inclinometer casing deformations are in reasonable agreement with those predicted by the 3D finite difference models. The measured surface subsidence and pillar pressure are in excellent agreement with those predicted by the 3D models. Results from this 2017 research clearly indicate that, under deep cover, the measured horizontal displacements within the abutment pillar are approximately one order of magnitude smaller than those measured in a 2014 study under medium cover.INTRODUCTIONDue to a recent shale gas boom, approximately 1,400 unconventional shale gas wells have been drilled through active and future coal reserves in Pennsylvania, West Virginia, and Ohio over the past 15 years. These shale gas wells have penetrated many coal seams, such as the Sewickley, Pittsburgh, Upper Freeport, and Kittanning seams. These unconventional gas wells, whether tapped into the Marcellus or Utica formations, contain very high gas pressure. Strata deformations associated with longwall and other high extraction techniques could induce high stresses and deformations in the shale gas well casings. This could seriously compromise the mechanical integrity of the production, intermediate, and coal protection casings (Figure 1). Damaged well casings could potentially introduce high-pressure, explosive gas into underground mine workings, particularly during an extended well shut-in period, which could seriously jeopardize underground miners’ safety and health."

Jan 1, 2018

By P. G. Toledo, R. I. Jeldres, G. R. Quezada

Chile is the main producer of copper in the world and lately the mining industry has suffered challenges due to the lack of water in the north of the country, along with the new policies of not using fresh water for the industry. This has prompted the use of seawater as an alternative source for mining. Several studies have been driven due to this new scenario, which have shown that seawater can be beneficial, if certain ions are removed from the process. This is the Mg that generates precipitates at high pH, that have been shown to make mining operations difficult. In particular, thickening operations are impaired by the presence of Mg ions, where aggregate formation and sedimentation decreases substantially. Our studies suggest the competence of the precipitates in adhering to the polyacrylamide (HPAM) flocculant and not towards the surface of the quartz minerals. This motivates the present work to use molecular dynamics to study the adsorption of a HPAM molecule on quartz surfaces and the surfaces formed by Mg precipitates. The surfaces are immersed in a saline solution or seawater that includes the HPAM molecule. Results are obtained by measure the adsorption frequency and duration. We obtained that the HPAM molecules are preferably absorbed on the surfaces of magnesium hydroxide. This gives us a good agreement with what is observed experimentally and strengthens the premise of the competition of hydroxide with the flocculant. Keywords: Molecular dynamics, adsorption, tailing flocculation, magnesium removal

Jan 1, 2020

By M. Moats, I. E. Paschalidou, K. Awuah-Offei

Tellurium (Te) is a rare metalloid that is predominantly produced from the treatment of anode slimes formed during copper (Cu) electrolytic refining. The US Government lists Te as one of the 50 critical minerals, partly, because of its use in thin-film photovoltaic (PV) technology. Given policy initiatives to increase Te production, it is important to evaluate the life-cycle environmental impacts of Te recovery as a by-product of Cu processing. The literature contains a few specific life cycle assessment (LCA) studies of groups of metals that include Te without proper regard to impacts per life-cycle stage of Te production or the effect of allocation on the results. This study builds an LCA model of the production system of Te from anode slimes treatment to evaluate the effect of allocation on life-cycle impacts. We build life cycle inventories using data from the Ecoinvent v3.7.1 database, literature, and engineering calculations and allocate impacts in proportion to products’ mass and economic value. The results show that economic value-based allocation yields greater impacts than mass-based allocation indicating the significant effect of the allocation approach on life-cycle impact estimates.

Feb 1, 2023

By B. Hines

Grinding efficiency in a vertical stirred mill is affected by a wide range of process and mill configuration variables. Of these, the media fill, size, and intrinsic density have a significant effect on power draw and grinding performance. Media-related factors that influence grinding performance include, e.g.,a higher media filling providing additional particle breakage sites, or a lower bead density decreasing the running torque at a given media filling. It has been estimated that the grinding media can cause up to a 30% change in the specific energy required to grind. FLSmidth has generally recommended that the intrinsic density (specific gravity) of the grinding media be more than triple the slurry density. This density difference helps to ensure that sufficient stress intensity is generated in the mill to provide particle breakage. It also reduces the chance of media ?float? if there is a spike in either slurry density or slurry flow rate. The VXPmills have historically operated at slurry density values between 1.2 and 1.5 kg/L, which translates to nominal bead intrinsic density range between 3.6 and 4.5 kg/L. The current trend towards regrinding bulk flotation concentrates to even finer sizes, to improve recoveries of fine grained minerals, has provided motivation to consider closed-circuit operation of stirred media mills. The slurry density in this application is typically higher than in open-circuit operation due to the higher percent solids in cyclone underflows. An additional effect is that closed-circuit operation increases the potential for media float due to higher flow rates as slurry is recycled to the mill. The normal progression in extending the operating range of existing equipment is to carry out laboratory testing before pilot-scale and plant-scale trials. The results presented in this paper examine the media density to slurry density ratio and its effect on grinding performance.

Feb 23, 2014

By Shaik Jeelani, Mahesh Hosur, Esperidiana A. B. Moura, Rejane D. Campos, Emilia S. M. Seo, Kerry Kirwan, Francisco R. V. Díaz, Maria Sotenko

The use of natural fibers with polymeric resins has spread rapidly. In order to improve the mechanical properties of material, in this work, two variables were used: mercerization and electron beam irradiation. This paper describes the preparation and characterization of biocomposites that were prepared in two different routes using green high density polyethylene (HDPE) and Brazil nut pod fiber (BNPF): the first was to irradiate the composite with 150 kGy and the second was to irradiate the matrix with 15 kGy followed by composite preparation. In both cases mercerized and non-mercerized fibers were used. The irradiation process was carried out using a 1.5 MeV electron beam accelerator, at room temperature and in the presence of air. The material was characterized to evaluate the effect of treatment on mechanical properties of material.

Jan 1, 2015

By Lang Tao, Jun Wang, Wei Xiao, Wenqing Qin, Pan Cao, Guanzhou Qiu, Key Lab of Biohydrometallurgy of Ministry of Education, Central South University

"The effect of metal cations on the rutile flotation using styryl phosphoric acid (SPA) as the collector was investigated by micro-flotation test, bench scale flotation test, zeta-potential measurements and adsorption measurements. The micro-flotation results indicated that Fe (?) and Al (?) ions in low concentrations had obvious activation on the rutile flotation, and Pb (?) ions in low concentrations had smaller activation of rutile, but Fe (?), Al (?), Pb (?), Ca (?) and Mg (?) have strong inhibition of rutile flotation in high concentrations. The bench scale flotation results indicated ethylene diamine tetraacetic acid (EDTA), boracic acid, and sodium hexametaphospate can decrease the metal ions concentrations, and increase the recovery of rutile flotation. Adsorption measurements and zeta-potential measurements revealed that Fe (?), Al (?) and Pb (?) ions were adsorbed on the rutile surface, and had interaction with SPA. But when these ions concentration were over the largest adsorption capacity, residual metal ions could occur chemical reaction with SPA.INTRODUCTIONRutile is one of the favored minerals for production of titanium dioxide white pigment, primarily through the chloride manufacturing process (Stanaway 1994; Hou et al., 2013) However, the majority of rutile ores belong to refractory ores, while flotation is one of the most efficient methods to separate fine rutile from gangue (Dolbear et al., 1937). With the flotation development, many effective collectors were successfully applied in the oxide ore. Many reviews have indicated that organic phosphonic acid collectors showed good selectivity on oxide ores such as ilmenite and rutile (Bulatovic & Wyslouzil 1999; Liu & Peng 1999).It is inevitable that many types of metal cations are present in ore pulp. These metal cations significantly influence the flotation of minerals. Liu et al. (2015) showed that Ca2+ and Mg2+ could improve the floatability of spodumene at pH 12.5 and 10.0, respectively. The authors proposed that Ca2+ and Mg2+ ions readily form hydroxy complexes (CaOH(l) and MgOH(l)) and precipitates as (Ca(OH)2 and Mg(OH)2) in strongly alkaline solutions. Fan and Rowson (2000) investigated the effect of Pb(NO3)2 addition as an activator on ilmenite flotation and showed that it could improve ilmenite floatability. The addition of Pb(NO3)2 resulted in an increase of ilmenite zeta potential in both weakly alkaline and acidic aqueous solutions. Mehdilo, Irannajad, and Rezai (2015) studied three kinds of ilmenite of different origins and discovered that both Mg and V had a negative correlation with ilmenite flotation, while the Mn content seemed to correlate positively with flotation efficiency. A number of studies have also showed that Fe3+ can improve the floatability of ilmenite (Fan et al., 2009; Nuri, Mehdilo, & Irannajad, 2014)."

Jan 1, 2016

By Huijun Shao, Qiang Liu, Zhengming Yi

The increase of the proportion of high Al2O3 content iron ore fine in iron and steel enterprises has brought about a series of problems such as the increase of the viscosity of blast furnace slag and the difficulty of the separation of slag and iron. In order to solve this problem, the effect of increasing MgO content on the technical and economic index, the cold strength, and metallurgical properties of high basicity and high-alumina sinter was studied through sinter pot test. Nova400NanoSEM field emission scanning electron microscope was used to analyze sinter microstructure. The experimental results show that when the MgO content fraction in the sinter with high basicity and high aluminum increases from 1.72 to 2.49%, the vertical sintering speed decreases by 4.38mm/min, the utilization coefficient decreases by 0.51t/(m2 h), and the low-temperature reduction degradation index increases by 6.7%. When MgO content in sinter is 2.11%, drum index and reducibility index are the highest, reaching 61.93% and 86.39% respectively. Mg2+ is mainly solid dissolved in the magnetite lattice and replaces Fe2+, up to 3.64%. The generated magnesie-containing magnetite inhibits the phase transition from Fe3O4 to Fe2O3 oxidation process in the sinter cooling process, which reduces the generation of secondary hematite and is conducive to improving the low-temperature reduction degradation performance of sinter.

Jul 4, 2021

By S J. Kim, S W. Kim, L Tomas da Rocha, S Jung

Al2O3 has been regarded as a harmful gangue component in iron ore, especially causing reduction degradation in industrial sintering of iron ore. The current study aimed to utilise low-grade iron ore containing high Al2O3 content in sintering process. In order to counteract the adverse effect of Al2O3 on reduction behaviour of iron ore sinter, mill-scale and calcined dolomite were chosen as FeO- and MgO-bearing materials. Firstly, mill-scale was added to high Al2O3 sinter and addition was optimised as 10 wt per cent, then calcined dolomite was added further. Magnetite and magnesio-ferrite were identified as the major phases in iron ore sinter when adding mill-scale and calcined dolomite. As the dosage of calcined dolomite increased beyond 4 wt per cent of in sinter mix, unreacted MgO particles were observed, which is ascribed to the limitation of MgO dissolution into magnetite matrix. Both mill-scale and calcined dolomite were effective in improving compressive load and Reduction Disintegration Index (RDI) of iron ore sinter although its reduction degree was highly decreased. The addition of both FeO and MgO-bearing materials to high Al2O3 sinter has a potential to improve the sinter quality, also contribute to the recycling of industrial by-product. However, the amount should be optimised in views of phase development and deterioration of reducibility.

Jun 19, 2024

By X. P. Zheng, H. K. Lin

Barium fluorophlogopites were synthesized in the laboratory to investigate the effects of composition and crystal parameters on surface properties and floatability. The negative surface charge of mica is determined by the barium content, the crystal cell volume, the distance between the layer structure and the Ba-O bond length. The higher the barium content, the larger the cell volume and distance between the layer structure, and the longer the Ba-0 bond, the more negatively charged the surface is, and, hence, the more easily adsorbed are cationic collectors. When an anionic collector (sodium oleate) is used, barium oleate forms on the mica surface and hence chemical adsorption occurs.

Jan 1, 1995

By T. Nghipulile, G. Dzinomwa, J. Kurasha, M. Amwaama, B. Mapani, K. Maweja, T. E. Moongo

The effect of mineralogy on the grindability was investigated using three copper ores – two sulphides and one oxide. The dominant copper minerals were identified by optical microscopy and mineral chemistry derived from SEM-EDS analysis. The sample designated sulphide 1 was borniterich, sulphide 2 ore was mainly chalcopyrite, and the oxide ore was predominantly malachite and minor azurite. The gangue minerals were identified using semi-qualitative XRD analysis. Sulphide 1 contained more than 80% (w/w) of quartz compared to about 70% in the other two ores. The Bond work indices were 13.8, 21.6, and 17.3 kWh/t for sulphide 1, sulphide 2, and oxide ore respectively. This suggested that the chalcopyrite-rich ore is the hardest, while the malachite-rich ore has intermediate hardness, and the bornite-rich ore is the softest. The brittleness indices of the ores were calculated using the chemical composition of the gangue, and a good correlation between brittleness indices and Bond work indices was observed, which highlights the importance of the gangue composition in determining the fracture behaviour of the ores. There is scope for further investigation into the relationship between ore mineralogy and comminution behaviour using other breakage characterization techniques.

Mar 30, 2023

By Zygmunt Kowalczyk

"A theory permitting the determination of expected surface deformations for planned underground exploitation is proposed and discussed in this paper. The relations between surface subsidence and various methods of mining are analyzed, and allowable horizontal .deformations for protected objects, according to the degree of their significance, are reviewed."

Jan 1, 1966

By A. K. Alzo?ubi

Block toppling in natural rock slopes has been under investigation since the 1970?s. De Freitas and Watters (1973) introduced the term ?toppling? to describe the movements of rock slopes by rotation in steeply dipping beds. The Lornex pit case history from British Columbia (Canada) was chosen to study the effect of mining on the stability of toppling rock slopes. A discrete element approach that allows fracturing of intact material was applied successfully to model the composite rock slide-rock topple movement. Three main movement modes were observed in the field and the numerical model; the sliding of the top of the slope exposed normal scarps, the toppling at the middle part of the slope exposed obsequent scarps facing opposite to the slope face, and dilation of the rock caused by fracturing at the toe formed loose material. The development of the rupture surface at the toe of the slope was traced and did not evolve into a continuous rupture surface throughout the slope both in the field and the numerical simulation. Good agreement was achieved between the deformations recorded in the field and the numerical simulation.

Jun 1, 2012

By Robert H. Raring

Viewed abstractly, a mill may be defined as a mineral processing facility located somewhere between the mine and the tailings storage area, Just how mining operations and the demands of tailings storage affect mill design is, the subject of this paper. At the outset, it will be readily acknowledged that no two installations can, or ever will be the same. At one extreme is the bucket line dredge where the distance between the ?mine? and the tailings area is measured in terms of tens of feet. At the other extreme, the large open pit copper mines are frequently spread across twenty, miles or so of countryside with the ore moving to the mill, as exemplified by the operations at Bingham Canyon, Ray, or Ruth - the "upstream" counterparts of Garfield, Hayden and McGill. In each of these cases, mill location was largely determined by requirements for tailings storage and/or water supply.

Jan 1, 1961

By R. Venugopal, V. K. Saxena, Veerendra Singh

"Ore morphology plays a vital role during the milling and liberation of minerals. This study was carried out to understand the role of mineral crystallography and mineral interfaces on the milling and liberation processes. Data related to mineral crystallography, Vickers Hardness Number and beneficiation processes were collected from literature, and detailed statistical analysis was conducted to relate these parameters. Review of the crystallographic information of minerals present in ores indicates that molecular weight and cell parameters significantly affect milling and liberation characteristics. Mineral interfaces were classified into the three categories of coherent crystals, semi-coherent and incoherent crystals, and breakage behaviors were studied. The studied cases revealed that these material interfaces control the micropore properties that play a vital role in the initiation of intergranular and intercrystalline fractures which occur in siliceous manganese ores and dolomite as a result of thermal treatment. In contrast, banded hematite jasper and coal exhibited a much more complex fracture pattern due to their coherent interfaces and finer physical associations. This study explains the effect of the various types of interfaces on milling, and the approach can be helpful in developing a methodology to enhance mineral liberation with minimum energy consumption.IntroductionComminution is a vital unit operation in the mineralprocessing, cement-making, power-generation and pharmaceutical industries. Its importance in mineral beneficiation operations is increasing every year as a result of the growing need to exploit lower-grade ore bodies and process reject materials (Blazy et al., 1994; DOE, 2005). Low-grade ores require significant energy during grinding to liberate the valuable minerals, which are further separated from the gangues by various beneficiation methods. Various attempts have been made to enhance mineral liberation during grinding to minimize energy consumption. Most of these studies focused on the analyses of the compression mechanism, chemical additives, thermal treatment, microwave treatment and electric disintegration (Klimpel and Austin, 1982; Norgate and Weller, 1994; Bearman et al., 1997; Kumar et al., 2010; Wang et al., 2011; Singh et al., 2012). However, many of these efforts had limited success, and there is a need to see the problem from a fresh perspective."

Jan 1, 2015

By J. Rostami, P. P. Nelson, A. Khetwaln

Tunnel boring machines (TBMs) can be considered as the method of choice for tunneling in many projects due to the high level of efficiency and high potential productivity, safety, and applicability in a variety of subsurface conditions. The muck transportation system in a TBM tunneling operation plays a significant role in the process and impacts the overall performance of the machine. This paper introduces a recently developed method of simulating TBM operation through discrete event simulation (DES), which allows for tracking of the various activities, incurred downtimes in the operations, and overall machine utilization. The study presented here compares two different muck transportation systems, conveyor and rail, under similar geological conditions to quantify the impacts of the choice of muck transportation systems on machine utilization. The results show the applicability and extent of redundancy in the use of the two systems relative to machine capabilities and their sensitivity to geological conditions.

Jun 13, 2021

By D J. Williams, C Zhang, F E. Herrera Cabrera

Farming on bauxite residue using screw propelled equipment (SPE) has been commonly practised to accelerate dewatering and as it promotes consolidation and enhances storage capacity. However, it is unclear when and how often farming should be conducted during the transition of bauxite residue from slurry to dry solids and how deep each slurry deposition should be. To address this issue, three desiccation tanks were established in the laboratory to investigate how much farming could enhance the desiccation and consolidation of tailings. The cuboid tanks, of 350 mm in height and 300 mm in width and length and with an opening on the top, were placed on load cells to monitor the water loss during desiccation and were instrumented with moisture and suction sensors designed and developed at the University of Queensland to measure the water content profile of the residue. The bauxite residue, composed of silt-size particles with low plasticity, was hydraulically deposited in the tanks as a slurry at 27% solid content, resulting in 100 mm depth of solid material settling. Evaporation was enhanced by placing two identical electrical fans above the tanks. Two phases were conducted. In the first phase, the two tanks were left untouched for evaluating non farmed conditions and for calibrating sensors, while in the second phase, three tanks were subjected to atemporal farming using purpose-built screw propelled equipment. The experiment was terminated when the residue was completely desiccated. This paper reports on the instrumented tank set-up and the results obtained to date.

Jul 1, 2021

By David Whalen

Mobile equipment in oil sand mining operations experience more maintenance problems than similar equipment in other surface mines, due to soft underfoot conditions. Oil sand properties are known to vary with temperature, bitumen content and previous loading cycles. One of the challenges is the widely variable underfoot pressure which supports shovels and trucks. In the case of a heavy hauler driving on in-pit roads, each tire is supported by a different ground stiffness resulting in an apparent uneven surface. Driving over uneven ground causes twist in the truck frame, which is transmitted to the dump body. Through a finite element analysis of a haul truck dump body, it was shown that slight frame twists produce localized stresses in the intersections of the floor stiffeners. These stresses are at times greater than those resulting from the maximum ore weight and are primarily responsible for cracking in these intersections. Syncrude maintains high quality haul roads, which are constructed of gravel, and makes every effort to keep the shovel pit roads as smooth as possible. This problem cannot be avoided through operational practices only and must also be accounted for in the design of haul truck bodies.

May 1, 2003