Search Documents

By J K. Claflin, S R. La Brooy, A M. Claflin

Rotary kilns have been in service in the gold industry to regenerate carbon for 65 years. At the time oxide ores with gold head grades of 8 to 10 g/t were being treated. Carbon could be regenerated adequately at 650°C and solution losses were less than 1%. Forty years ago, research indicated that heavily fouled carbon from flotation circuits had to be held at 750 to 850°C for ten to twenty minutes for full reactivation (Avraamides and La Brooy, 1987), gold head grades were typically 5 g/t and solution losses typically 0.02 ppm – still less than 1%. In 2017 it was determined (Claflin et al., 2017) that a residence time of less than 1 minute at 750°C can be adequate to reactivate carbon fouled with organics sufficiently to achieve 0.005 ppm solution losses in a flotation tailings leach plant.With the potential for discovery head grades to drop below 0.6 g/t, solution losses of 0.02 ppm represent over 3% loss. Tight operation of the whole carbon circuit is required to keep gold solution losses below 1% going forward.There are alternatives to a rotary carbon kiln, e.g. vertical kilns of which the Minfurn, Rintoul and Combustion Air kilns are examples. The alternative kilns can be heated using electrical heating elements, induction, and microwave. These kilns can operate successfully under the right conditions, however, they are almost exclusively for small carbon throughputs and are not suitable for the large carbon advance rates that are required to process low head grade ore deposits. Large throughput carbon kilns are are almost exclusively fossil fuel fired rotary kilns and the subject of this paper. In the view of the principal author, a fossil fuel fired vertical carbon kiln is preferred to a rotary kiln, however, it is not currently used in the industry.Thermal regeneration of activated carbon has a major impact on gold recovery in the carbon circuit. The carbon kiln and associated equipment constitute 3 to 5% of the capital cost for an oxide processing plant and up to 10% of the capital cost if flotation tails are leached. Despite the capital cost and impact on recovery, the carbon kiln is often poorly selected, operated and maintained.Six years ago Ausenco embarked on the Carbon Kiln Initiative to reduce solution gold losses. This body of knowledge has been published in a series of papers culminating in this paper on how to:1. Select a kiln appropriate for the flowsheet;2. Maintain the kiln to achieve design operation; and3. Operate the kiln to minimise costs and maximise reactivation.CITATION:Claflin, J K, La Brooy, S R and Claflin, A M, 2018. Carbon kiln selection, operation and maintenance, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 251–274 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By M. J. Latva-Kokko, CA Snyders, J. R. Peltola, M. K. Kostiainen

It is well known that carbon management is essential for minimising soluble gold losses in carbonin- leach (CIL) and carbon-in-pulp (CIP) circuits. Even so, carbon measurements remain predominantly a manual operation with a low amount of control and automation around CIL and CIP reactors. Carbon inventory, i.e. knowing the carbon concentration in each reactor, is crucial for good carbon management. CarbonSense, a novel in-situ measurement system, was therefore developed for continuous monitoring of the carbon concentration in each reactor and paves the way for more advanced control in gold operations. The carbon management and optimisation system is based on Outotec® HSC Sim dynamic process simulations where each process component is modelled in detail. Generated models are validated with real data from a particular operation. The simulator will allow for the carbon control sequence to be realistically tested and the efficiency optimised by controlling the feed and discharge pumps in a hazard- and risk-free process environment. Furthermore, by combining CarbonSense and Outotec® gold courier (online soluble gold measurements) continuous feed-forward and feedback information can be obtained. The optimiser will then define the best running parameters based on the cost function of gold production versus intrinsic factors such as utility costs and adsorption time. Eventually, the application can be installed parallel with a real process island and it can be continuously calibrated with real-time process data. The dynamic model will then create future predictions for the entire process island. The example case presents a CIL circuit, which is simulated using Outotec® HSC Chemistry Sim and operated through Outotec® ACT (Advanced Control Tool) application. Keywords: Carbon-in-leach, CIL, CarbonSense, carbon management, automated control, simulation

Jan 1, 2020

By Pierre Auger, Benoit Levesque, Richard Martel, Guy Sanfacon, Louis-Charles Boutin, Marc-Andre Lavigne, Patrick Brousseau, Luc Trepanier, Louise Galarneau

Explosives used for blasting operations in civil engineering works, like construction of piping systems under roads, of pools, of houses and buildings can generate large volumes of carbon monoxide (CO). Carbon monoxide can represent between 1 to 3% of the gases produced by usual explosives. The production of 10 to 24 1 of CO by kg of explosives blasted is theoretically anticipated. CO is a gas that has no characteristic colour, smell or taste. It can migrate in the fractured rock of the blasted areas on fair distances, and then infiltrate in closed spaces like sewage systems, manholes, but also in basements of houses. In Quebec, in the last 10 years, 7 people were poisoned by CO in their houses to the point that they had to be treated in hyperbaric chambers. In the USA, many accidents have occurred and one worker died in a manhole. From the review of intoxication cases, the distance of migration of CO may reach 55 m if a conduit is present underground. Underground conduits broken by blast, tilling around underground conduits in road or house trenches, or fractured rock created by blasts between houses or between a house and a road, are the different pathways identified in the Quebec incidents. Field tests were performed at sites close to CO intoxication locations in order to evaluate the behaviour of CO in fractured rock following blasting operations. From these tests, the following conclusions may be drawn. The structural geology of the rock formation (schistosity, family of joints, fractures) plays a role in the direction and extent of gas migration in fractures generated when rock is blasted with explosives. The confinement of the rock can affect the quantity of gas migrating in the fractured rock. Significant concentrations of CO may persist in the fractured rock even 7 days after a blast. Advection is the initial mechanism of CO migration in fractured rock generated by the blasts or naturally occurring before the blast. The distance of migration with this mechanism is short (5 to 8 m). In trenches of muck (equivalent to tills under roads) the distance of CO migration by advection is 12 to 20 m. In the 2 to 3 days following the blasts, further CO migration up to 15 m is made by diffusion in the induced fractures, or up to 30 m in the trenches. To minimise CO production and migration in the fractured rock during blasting, special procedures can be applied by the blasting contractors: (1) do the complete excavation of the overburden before drilling and put mats for each blast; (2) do the complete excavation of the muck after each blast; (3) the last blasting should be the one for the private services entrance of the house and the excavation of the muck should begin at the junction between the road trench and the services entrance trench. Another technique consists in the pumping of interstitial air in the muck with a vacuum truck immediately after each blast.

Jan 1, 2002

By Nadya Michel, Daniel Gros-Jean

This is a true story. Names have been changed to illustrate the importance and impact of carbon monoxide risk management in explosive blast projects and the community « Honey I’m not feeling good…” “What is going on Michael?” – – Michael was not answering so Julia, who was on the third level of the magnificent house, hurried down the stairs to check up on him in the basement. Today was day 2 of the construction work of the bathroom, yesterday they had excavated all the space for the shower. She started to breathe heavily as she was approaching the bathroom and saw Michael unconscious on the floor. “Michael!” – Julia immediately dialed 911. She opened a window since the air was heavy and went by Michael to hear him breathe and take his pulse. The paramedics took Michael on a stretcher and rushed him to the hospital. “I’m feeling dizzy” she thought to herself a couple of hours after the incident, and heard Matthew say: “Mom, I’m feeling sick”. Suddenly, she felt like she would pass out and felt in danger but couldn’t move. She desperately searched for her cellphone and dialed 911 but couldn’t speak. The dispatcher sent the firefighters and paramedics to the GPS location that was appearing on the screen and the emergency team was alerted that it was a second call in hours at the same address. When the firefighters arrived, they had to force the door to enter and found Julia in her bedroom on the third floor and Anette and Matthew also unconscious in their bedroom, lying on their respective bed. There was no smoke but on their multigas meter, carbon monoxide (CO) peaked at 1500 ppm on every level of the house, which is abnormally high.

Feb 6, 2023

By Dilermando Nagle Travessa

High strength-light weight materials are very attractive for the transportation sector, particularly to the aerospace industry. High strength-age hardenable aluminium alloys are widely used in airframes due to their unique combination of strength, density, toughness, corrosion resistance, cost and easy processing. However, the hardening capacity of such alloys is somehow saturated due to thermodynamic issues related to the conventional processing. The production of aluminum-matrix composites is a promising strategy to overcome this limitation, resulting in strength levels that cannot be reached by actual commercial aluminum alloys. In the present work, multiwall carbon nanotubes were used to reinforce the AA6061 aluminium alloy. 1 and 2% weight percent of MWCNT were mixed to the alloy powder by high-energy ball-milling process. The blended powder was consolidated by hot extrusion. The obtained composite bars were submitted to heat treatment for the T6 condition in order to combine both CNT dispersion and precipitation hardening effects. Optical and scanning electron microscopy, as well as hardeness testing, was used to characterize the bars. Typical wrought microstructure, free of defects, was observed on the extruded bars. Hardness of the composites was observed to increase by 20, 28 and 68% for 1% MWCNT 6 h milling, 2% MWCNT 6 h milling and 2% MWCNT 10 h milling, respectively, in the as-extruded condition. The better performance for the composites blended at higher milling time was attributed to a better nanotubes dispersion. Subsequent heat treatment to the T6 condition did not result in additional hardening.

Aug 8, 2018

This treatise presents the application of the vertical furnace in a carbon regeneration system. Comparison is made to a rotary kiln. The construction, operation and control of the vertical furnace and system components are discussed. Advantages include high efficiency, fuel economy, minimal mechanical apparatus and maintenance, atmospheric and temperature control, ease of operation and reliability.

Jan 1, 1985

By W. Lodge, G. Rasmussen

"The carbon-in-pulp (CIP) process has been the dominant gold recovery technology since the 1980s. During all this time carbon measurement, and control of the carbon transfer pumps has been largely manual in nature. Such manual operation inevitably limits process efficiency, potentially resulting in higher gold solution losses, and higher cost of circuit operation. Based on the authors’ experience, average plant solution loss is in the range of 0.02-0.03 ppm Au, as opposed to the general industry target of 0.01 ppm Au or less. Gekko Systems, in conjunction with Curtin University’s Gold Technology Group, has developed a carbon concentration meter, the ‘Carbon Scout’ meter. The meter automatically measures carbon concentration in all tanks, providing more frequent and more precise data. Combined with SIMCIL, a CIP circuit process model which is used to determine the optimum set points for the circuit, the meter should ensure lower gold solution losses, and more efficient operation of the carbon circuit. This paper will review they critical factors for good carbon management, the development of the meter and results from the first plant installation. Additional benefits of the Carbon Scout, including improved health and safety and the opportunity to measure other key variables in the leach/adsorption circuit from one central location will also be described.INTRODUCTION The carbon-in-pulp (CIP) process was first introduced to the gold industry in the early 1950s at the Carlton Mill in the USA (Fast, 1988), with the modern version of CIP becoming fully developed with large scale installations in South Africa in the late 1970s (Laxen, 1982). CIP quickly became the technology of choice for new operations, and for the retrofitting or upgrading of existing operations. In the 1980s the carbon-in-leach (CIL) circuit configuration became the process design of choice due mainly to its lower capital costs. With 40 years of operational experience, CIP/CIL for gold recovery is now mature a technology, whose operations and limitations are well understood. To extract further efficiencies from such technologies, by improving recoveries and/or reducing operating costs, is challenging and may require new approaches to circuit management. Gekko Systems, in association with the Gold Technology Group at Curtin University, has developed the Carbon Scout, an automated carbon measurement device. This device replaces manual measurement of carbon concentration in carbon adsorption tanks, providing more frequent and more accurate data for control of the CIP process. Data from the Carbon Scout can be used to automatically control the carbon forwarding pumps."

Jan 1, 2018

By H. L. Retcofsky

Carbon-13 nuclear magnetic resonance (18CNMR) spectra of nine 2-substituted pyridines, seven 3 -substituted pyridines, and nine 4-substituted pyridines have been obtained and analyzed. Substituents included both electron-releasing groups and electron-with hawing groups. Substituent effects on the magnetic shieldings of the ring carbons, except for those in the 2-positions of 2-substituted pyridines, were found to be quite similar to the effects reported for the monosubstituted benzenes, Thus, at least to a first approximation, the two classes of compounds have similar shielding mechanisms. Shieldings of the carbon atoms in the 5-positions of 2-substituted pyridines and those in the 6-positions of 3-substituted pyridines were found to reflect electron release or withdrawal by substituent groups, The pyridinium cation and the compounds 2,2'-dipyridyl and benzonitrile were also investigated.

Jan 1, 1969

By X Liu

The crystal chemistry of carbonate in Ca apatites, including Na-free and Na-bearing hydroxylapatite (CHAP) and Na-bearing fluorapatite (CFAP) and chlorapatite (CCLAP), has been investigated by Fourier transform infrared (FTIR) spectroscopy and single-crystal X-ray structure, using crystals synthesised from carbonate-rich melts at 1 GPa, 1400 - 1000¦C. The carbonate ion substitutes for both the X (OH, F, Cl) anion species in the apatite channel (type A carbonate) and the phosphate group (type B carbonate). The type A carbonate ion is oriented in the channel with two oxygen atoms close to the c-axis, and the type B carbonate ion is located close to the sloping faces of the substituted phosphate tetrahedron, with details varying with composition series. Sodium promotes the uptake of type B carbonate and also has a profound effect on FTIR spectra. Crystal compositions correspond approximately to the substitution formula Ca10-(y+z)Nay z[(PO4)6-(y+2z)(CO3)y+2z][X2-2x(CO3)x], with x + y up to 1.0 and z + 0.0 for CHAP, x + y + 4z + 0.4 for CCLAP, and x + y + 2z + 0.1 for CFAP, for equivalent conditions of synthesis. The sodium cation and A and B carbonate ion defects are locally coupled in all three composition series to facilitate charge compensation and minimise the effects of spatial accommodation. Synthetic Na-bearing type A-B CHAP with x + y + 0.5 has a similar chemical composition and FTIR spectrum to biological apatite.

Jan 1, 2008

By N. A. Abdel-Khalek

The amenability of carbonate separation from a sedimentary phosphate ore using a bioflotation process was studied. Two types of bacteria were chosen for this study. The experiments were performed using oleic acid as collector. The flotation experiments were carried out using statistical designs for optimizing the main operating parameters. A concentrate containing 0.78% MgO and 30.15% P2O5 with a recovery of 92.31% was obtained from a feed containing about 2.45% MgO and 27% P2O5. These specifications could not be obtained using conventional flotation experiments under similar conditions in the absence of bacteria. Measurements of zeta potential, adsorption of bacteria and collector, as well as froth power, were performed to explain the role of microorganisms in the surface modification of both dolomite and phosphate and in their interaction with the collector.

Jan 1, 2009

By Peter Megaw

The paper point out that the carbonate Carbonate Replacement Deposits (CRDs) are epigenetic, intrusion-related, high-temperature sulfide-dominant Pb-Zn-Ag-Cu-Au-rich deposits that typically form lenses or elongate to elongate-tabular bodies referred to as mantos or chimneys. Recent studies have shown that CRDs do occur in predictable geologic environments, allowing focusing of regional exploration. In addition, they have mappable alteration patterns that can be used to determine the magnitude of a given system and elemental zoning patterns that greatly enhance the chances of drilling success. Several recent discoveries of “blind” replacement deposits have been made by careful field evaluation of host and capping rocks coupled with geophysics.

Apr 24, 2001

By Bing Song, Fei Xi, Xuewei Lv, Kai Zhang

The electric arc furnace process is a common method to produce high TiO2 slag from ilmenite. The pre-reduction process was proposed in recent years in order to reduce electricity consumption. In order to enhance the pre-reduction degree, high energy ball milling was proposed to improve the specific surface area of the ilmenite prior to reduction. In this study, the carbothermic reduction behavior of milled ilmenite concentrate was investigated. It was found that the ball milling method can result in a higher reduction rate and improved metallization of iron. The metallization of iron increased with increasing the time of ball milling. The metallization of iron with milling reached 89.49% when the time of ball milling was 70 min., while the FeO content decreased with 70 min. of milling from 11.84% to 4.76%.

Jan 1, 2014

The nature of adsorbed calcium carboxylates (oleate and stearate) has been investigated by in-situ/ex-situ Fourier transform infrared internal reflection spectroscopy (FTIR/IRS). Previous spectroscopic studies in alkaline solution have shown that adsorbed carboxylate is characterized by a C-O stretching vibration at about 1550 em?1 for less than monolayer coverage. Similar results were found in this study. More specifically, in this study such a singlet at 1550 cm-1 was found for LB monolayers of calcium distearate transferred as a condensed layer at a high film pressure to the surfaces of fluorite and germanium. Normally the spectrum of bulk calcium distearate reveals a doublet at 1575 and 1540 cm-1, characteristic of a three dimensional 7-fold coordination for calcium carboxylate complexes. This doublet is generally found for carboxylate multilayers formed by spontaneous adsorption at the surface of calcium minerals. In this regard, the spectral evidence suggests that whenever the calcium dicarboxylate is constrained at a surface as a condensed layer, the 7-fold coordination can not be satisfied and the surface carboxylate is forced into a two dimensional symmetrical coordination with a singlet at 1550 cm-1. On the other hand, if the Langmuir-Blodgett (LB) monolayer calcium distearate film is transferred at a low film pressure the doublet is observed. This analysis is further confirmed by the spectral results for LB transferred calcium distearate monolayers at a hydrophobic silicon surface. Even though these are condensed monolayers formed at high film pressure, the carboxylate group, oriented away from the surface, is no longer constrained by the surface force field, and thus exhibits the characteristic doublet of the bulk calcium distearate salt.

Jan 1, 1998

By B. Caldwell

"The CompanyCardinal River Coals is jointly owned by Luscar Ltd. and the Consolidated Coal Company of Canada (Consol). The Luscar mine is operated by Luscar Ltd. and is located 40 km south of Hinton near Cadomin, Alberta (Fig. 1). The plant sits on the old townsite of Luscar, Alberta, which was founded in order to develop the coal in 1912 (Fig. 2). Initially, the coal was mined by Luscar Ltd. for heating and steam generation and used quite heavily by the railways for their steam locomotives. In 1955, the mine was decommissioned as the demand for coal for tl1ese purposes had dropped off. In 1969, the mine was re-established by Cardinal River to provide metallurgical coking coal for its customers in Japan. The coal is mined from the 13m thick Jewel Seam by open pit methods at a 10 to 1 stripping ratio. The run-of-mine coal is then cleaned to meet customer demands.The PlantThe clean coal preparation facilities at Cardinal River were extended in 1980 in order to increase the feed rate from 450 t/h to 800 t/h. The extension is a separate plant which can be operated on its own or in parallel with the old plant. In addition, modifications have been made to the fine coal circuit (hydrocyclones added), the coarse refuse circuit, (refuse bucks replaced by a refuse conveyor which backfills a pit), and the fine refuse circuit (solid bowl refuse centrifuges, refuse classifying cyclones, and hydra-rake thickener no longer utilized) since the plant was built in 1969. The plant production of 3 M t per year with a yield of 78% is achieved by first screening and breaking the run-of-mine material to a top size of 1 ½ in. The feed is then slurried, sized, and processed in three different washing circuits. The washed coal is mechanically dewatered, thermally dried, and then stored in a 14 500 t capacity silo or on a 300 000 t stockpile. The fine refuse is thickened and pumped to the same pit to which the coarse refuse is being conveyed"

Jan 1, 2000

By R Vuolio, B A. Jonsson

In the center of Helsinki - capital of Finland - extensive blasting operations were carried out during the years 1982 - 84. At the corner of the streets Mannerheimintie and Simonkatu - in the Forum block - about 125,000 cu.m. of rock were blasted to give place for a new modern shopping centre (Fig. 1). Added to this amount of rock another 10,000 cu.m. were blasted for a transport tunnel to an adjacent underground bombshelter (Fig.2) which is to be used as a parking place in peace-time. The blasting work was demanding and difficult to carry out due to old buildings surrounding the work-site as well as computers and other sensitive equipment installed in some of them.

Jan 1, 1985

By C. S. R. Rondestvedt

In February 2010, Teck?s newest Concentrator at Mina Carmen de Andacollo (CDA), Andacollo, Chile was commissioned. The Concentrator is a single line configuration, comprising of one 36 ft diameter x 20 ft long SAG mill driven by an 18,000 hp gearless drive. The SAG mill feeds two ball mills each 25 ft in diameter x 40.5 ft long, each driven by a total of 19,000 hp through dual pinion drives. A series of four phases will be reviewed from operational readiness, mechanical completion, commissioning, and ramp-up. Also, now after 6 months of operation, this paper will review the significant steps taken during ramp-up enabling the announcement of commercial production, in October 2010.

Jan 1, 2012

By Harry M. Castrantas

Caro's acid (peroxymonosulfuric acid-H2SO5) is used to destroy cyanides in tailings slurries due to its rapid reaction and low capital and operating costs. Due to its instability, Caro's acid is generated at the mine site using a hot or cold process. The majority of gold mines that use Caro's acid use the FMC hot process. In the FMC hot process, it is not necessary to cool the Caro's acid to minimize decomposition since it is used immediately upon generation. In contrast, the cold process uses a chiller to cool the raw materials and product. This paper will show, using laboratory and field data, that there is virtually no difference in Caro's acid yield between the cold and the FMC hot processes. Caro's acid yield depends on the mole ratio and concentration of sulfuric acid and hydrogen peroxide and is independent of operating temperature.

Jan 1, 1997

By H. M. Castrantas

Caro's (peroxymonosulfuric) acid has been reported to destroy WAD (weakly acid dissociable) CN-but, until recently, the technology has not been demonstrated in other than a laboratory setting. During the last two years, Caro's acid has been shown to successfully detoxify WAD CN-in tailings at two large North American gold mines. Using on-site FMC generators, Caro's acid reduced the WAD CN-from 40-55 ppm to below 20-35 ppm WAD CN-, the target range for the two mines. The detoxification costs using Caro's acid were less than 50% of the treatment cost of using hydrogen peroxide, the previous oxidant of choice. In addition to the considerable savings in CN-detoxification costs, lower WAD CN-values were achieved and the detoxification time with Caro's acid was greatly reduced compared to hydrogen peroxide.

Jan 1, 1995

By M. Yamine, R. J. Ring, D. J. Waters

"An experimental program has been carried out by the Australian Atomic Energy Commission to compare the effectiveness of Caro's acid as an alternative oxidant to pyrolusite in the leaching of uranium ores from the Alligator Rivers region of northern Australia. Batch leaching tests on Ranger, Nabarlek, Koongarra and Jabiluka ores showed that uranium extraction was unaffected by choice of oxidant, but that Caro's acid reduced acid requirements by 15 - 25%. Lime requirements for neutralization of tailings liquors were reduced by 20 - 30%.The batch studies were extended to a four-stage continuous leaching circuit with a capacity of 400 gore h-I. Comparative leaching tests confirmed the reagent savings obtained in the batch tests. Following these encouraging laboratory results, lnterox Chemicals Pty Ltd carried out plant trials using Caro's acid. Reagent savings in the mill were similar to, or better than, those obtained in laboratory test work. The trials also established that Caro's acid has a number of operational advantages over pyrolusite.IntroductionUranium is most commonly extracted from its ores by leaching in sulphuric acid. Simple hexavalent uranium oxides and compounds are readily soluble but uranium in the tetravalent form is insoluble and must be oxidized for dissolution to occur. The most commonly used oxidants have been sodium chlorate and manganese dioxide. They act indirectly by maintaining iron as the ferric ion which oxidizes uranium by a surface electro- chemical reaction. An Fe3+ concentration of about 1 - 2 g L-I is usually considered adequate for the effective dissolution of uraninite(1)."

Jan 1, 1984

By John J. Simmons

Federal and state regulations, in an effort to reduce acid rain, are becoming increasing more stringent regarding sulfur content of fossil fuels. Whereas coal from Illinois and Ohio contains between 1.5 and 37. sulfur, Wyoming has billions of tons of coal reserves containing less than O.5/% sulfur. However, much of Wyoming's coal is high in moisture, 25-30%, and low in energy, 8,200 to 8,900 BTU, vs. 10,500+ BTU for Illinois and Ohio Basin coals. Wyoming currently ships in excess of 130 million tons of coal to utilities as distant as Michigan, Wisconsin, Minnesota, Iowa, Nebraska, Louisiana, Oklahoma, and Texas. With freight charges ranging from $12.00-$20.00/ton, more than $1.5 billion a year is spent to transport water. A test shipment of more than 50,000 tons of Wyoming coal has recently been made from Mobil's Cabello Rojo Mine, south of Gillette, by Burlington Northern to the Robert's Bank British Columbia coal terminal for transloading and shipment to Taiwan Power Company. This coal assayed approximately 8,400 BTU/lb. and 277. moisture. Carbontec Energy Corporation feels the future availability of dried coal containing 11,000+ BTU could substantially enhance the potential export as well as the domestic market for Wyoming coal. Large and small utilities, along with industrial furnaces require tens of millions of tons of Wyoming, West Virginia, and other Eastern The federal government is encouraging the expenditure of hundreds of million of dollars by utilities to retrofit their boilers to allow them to burn higher sulfur coal. This program, if carried to completion, would cost many tens of billions of dollars, with the net result being high power costs sustained by the utilities. These costs will be passed on and paid for by the American consumer. A sensible alternative would be the burning of low sulfur coal by the utilities, without costly capital and operating expenditures. Carbontec Energy feels the successful operation of a Carbondry Coal Drying Plant in Wyoming will be the forerunner to other similar and larger operations in the State. CARBONTEC RESEARCH The activities of Carbontec's personnel to develop a viable process to dry sub-bituminous and lignite coal goes back some 14 years; in fact, for some of us it goes back to 1962 when we were involved in a program under which lignite coal from Truax Trayer's Velva mine was placed in low sulfur coal, which are burned alone or blended with high sulfur, Midwestern coal. Carbontec believes that a high BTU. reasonably priced, shippable coal fuel produced in Wyoming and delivered at costs competitive with Eastern low sulfur coal, could offer substantial benefits to Wyoming coal producers, utility customers, and to the State of Wyoming.

Jan 1, 1989