Search Documents

By M. Mankosa, G. Taylor, G. Luttrell, J. Yasalonis

Several industrial-scale HydroFloat separators have recently been installed at Mosaic’s South Fort Meade beneficiation plant for the purpose of improving phosphate recovery and throughput capacity. This technology was implemented after numerous laboratory, bench-scale, and on-site, pilot-scale test campaigns. The results from this detailed test work provided sufficient justification for the complete retrofit of the existing coarse and ultra-coarse flotation cells. Data indicate that the metallurgical results obtained with the full-scale separators are consistent with that obtained during both the bench- and pilot-scale evaluations. The apparent benefits, theory of operation, and commissioning of the equipment are also discussed.

Jan 1, 2007

By Jaidev Sankar

The dream of constructing the new Second Avenue Subway in New York has finally become reality as the first construction contract package is currently underway. This first contract requires the construction a TBM Launch Box in the middle of Second Avenue from which a Tunnel Boring Machine (TBM) will bore two tunnels south to 63rd Street. This paper will discuss the design of this contract and how construction has progressed including preparation, site constraints, utility construction and com-munity impacts while highlighting the challenges of working in an urban environment. It will also discuss moving forward on this major project outlining the remaining contract packages including their scope and status.

By Takayuki Sakai, Takefumi Takuma, Lee Roesner

"70-foot deep rectangular-shaped bulkheads were built with sheet piles as launching and receiving shafts for a pipe jacking operation for new underground waterlines in a densely populated section of Los Angeles, California. The Press-in Piling Method was specified to drive 95-foot long sheets (a record for the method) to form the bulkheads for the Los Angeles Department of Water and Power’s LA-29 (DWP) Connection Modification and Pipe Jacking. The piling was chosen because of its very low noise and practically vibration-free nature since the site is surrounded by houses, an apartment complex, and existing water lines. The out front areas of the bulkheads were grouted to let the TBM go through without major ground water leaks. Hydrophilic foam grout was also injected in addition to welding steel scab plates on the inside to seal them to achieve sufficient watertightness behind a few split interlocks. BACKGROUND This project was located in the Crescent Heights area of Los Angeles which is a few miles south of Beverly Hills. The project represents the completion of the last phase of the Stone Hollywood Trunk Line. This was an 8-mile long water trunk line that averaged 60 inches in diameter and was built to improve the reliability of the DWP’s major water system. This section of the project involved driving 2 deep shafts to allow for the installation of a 350-foot-long 72-inch steel casing using microtunneling construction. See Figure 1 for the shaft locations and the tunnel alignment. The challenge for the project was that this water line would have to pass beneath the Hollyhills buried box drain (15 feet high by 20 feet wide). Further complicating the construction was the soils beneath the drain. The DWP chose to drive the tunnel at a depth of approximately 65 feet to ensure that the ground conditions were uniform and suitable for the microtunneling equipment. There were two previous attempts to construct this work which failed because of poor ground conditions and very high water levels. This third attempt was critical because the DWP could not afford to have another failure due to the fallout with the residents being impacted by the project."

Jan 1, 2016

By J. Peterson, P. G. McKneight, R. W. Riggle

"In today’s tough mining environment, the key difference between surviving and thriving is how effectively miners optimize their mining operations. This paper explores the compounding effects material fragmentation has on mining costs and productivity. Starting with Drilling & Blasting and moving through Loading, Hauling and Crushing, we will illustrate the opportunities to improve operating costs and thus reduce the Total Cost of Ownership (TCO) of the total mining system. Material size and volume requirements are defined by the needs of the mill or plant, and drive the rest of the mining operation from the bench through the primary crusher. At the start of the cycle, where the rock mass is drilled and blasted, the degree of fragmentation and the muck pile configuration is determined, as are the effects on cost and productivity of all subsequent operations. The cost of managing oversize material, including secondary handling, overloading, reduced diggability, higher load factors, extra pass loading, increased wear factors and reduced throughput rates are all opportunities for improvement. INTRODUCTION Having visited many mine sites, customers are asking about the end to end mining value stream from loading to the crusher and how to measure the cumulative effects on each part of the mining value chain. All too often improvements with the drilling and blasting may impact fragmentation but do not improve the diggability so the net change on cycle times or fill ratios is perceived to be negative at the point of loading but they may have a measured improvement going through the primary crusher. This makes it imperative to measure performance at each segment of the overall cycle and not just to the crusher but thru it. The mine material process originates with solid rock, in-situ, and progresses to the output of the primary crusher. Once the material has passed the primary crusher the fragmentation size will be fairly consistent and promote consistent throughput of the plant or mill. In late 2015 a team was conducting a reassessment visit to a mining site where we had conducted the original assessment the previous year. Though many recommendations had been implemented some had been so recent they had not resulted in the expected improvements. Several of our discussions kept returning to the impact fragmentation has to both the individual components of the mining cycle but also the effects compounded throughout the end to end process. Let’s move on to the big picture before we zoom in on any specific operation. To get from native solid rock in the ground to a concentrate or a saleable rock product we have the same steps from one end of the chain to the other. We start with a good geological understanding of the rock type, characteristics and structure to design a program to drill and blast the rock. The height of the bench is relevant to the annual production requirements and the specific digging equipment models best sized to make that production possible. The equipment selection influences the bench height which has a minimum and maximum hole diameter to maintain a safe blasting operation. The diameter of hole burden and spacing all contribute to a good distribution of explosives in the rock mass that maximize the fragmentation and preconditioning of the rock when blasted. The timing and sequencing of hole initiation will yield a fragmentation ratio and diggability factor. Fragmentation size adjustments will change the meters drilled per cube and the explosives consumption will change accordingly. Drill cost is measured by meter drilled so a direct relationship exists between cost and fragmentation sized achieved."

Jan 1, 2017

By D. P. Richards

Tunneling in carbonate sedimentary rocks such as lime stones and dolomites can be difficult when solution channels or voids are anticipated. Addressing the risk aspects associated with these formations can be done effectively through the Geotechnical Baseline Report (GBR) by properly characterizing the ground and ensuring that the Owner?s and the Contractor?s interests are represented and protected. This paper presents a review of tunneling difficulties in these rocks and includes a review of site investigations, geologic characterization, and presentation in the GBR. Key construction issues are also discussed, including appropriate excavation technology, mechanisms of face support and groundwater control, and quantifying grout takes.

Breaks in coal slurry impoundments can threaten the lives and health of area residents, destroy homes and businesses and contaminate water supplies. This dangerous potential looms over coalmining regions in West Virginia and throughout Appalachia. The Coal Impoundment Project was begun in June 2003 to provide an inventory and mapping of active and abandoned impoundments in West Virginia. The project also provides the public with specific information about the impoundments in their communities. It is dedicated to alerting residents of danger and evacuation plans, reducing risk to residents and finding alternatives to impoundments. Since its first year, more than 100 impoundment sites have been added to the project’s Website.

Jan 1, 2005

By M. H. Col

Within the last few years, there have been numerous techno-logical advancements within material handling due, in part, to the introduction of conveying systems and mobile material handling systems to the industry. Although the traditional material handling methods are still commonly used, the introduction of conveyors to the industry has provided companies with some very efficient and economical options. These "new" systems change with the industry to accommodate rigorous demands, ease of operation, and low operating cost requirements. The number of mobile material handling systems utilized in mining operations is increasing, especially in heap leaching applications. Ten years ago, mobile material handling systems like Mobile Stacking Conveyors (MSC) were considered a novelty. There were two (2) MSC's in actual operation and only one of those in a heap leaching application. Today there are numerous proven systems operating at mine sites around the world-La Coipa, Zaldivar, Florida Canyon, Cananea, El Abra, Chuquicamata, and Radomiro Tomic. The popularity of mobile systems is due to the benefits realized by individual projects. As technology advances, so do the concepts behind mobile material handling systems. Implementing self leveling mechanisms, Programmable Logic Controllers, and Global Positioning Systems to control the equipment are just a few of the recent advances that will be discussed in this paper. We will also discuss current proven systems, and touch on what we see as some of the future advances.

Jan 1, 1998

By R. W. Amstutz

Abstract. The shaft was drilled on U.S. Government land in the Piceance Creek Basin and was funded by the U.S. Bureau of Mines. It was drilled to 723 meters (2 371') to provide access to rich deposits of oil shale, nahcolite and dawsonite for geotechnical test work and environmental mining research. Rotary drilling and dual string, reverse-air, jet-assist circulation methods were used. Drilling required 8 months. Site preparation, running and cementing the casing required another 4 months. A 2.44-meter (96-inch) ID steel welded casing, 5.1 cm (2 inches) thick was installed and 2 700 tonnes (63 000 sacks) of cement were slurried and pumped into the annulus.

Jan 1, 1980

By Anna Sukhanova, Svetlana Babaeva, Sergey Andreev, Victor Beltenev

"The Zenith-Victoria /1/ and Jubileynoye /2/ hydrothermal fields have symmetrical structural position on the Mid Atlantic Ridge (Fig. 1). In order to compare the evolution of hydrothermal systems, we conducted mineralogical and geochemical studies of SMS from both sites.Radiochemical and geochemical investigations of massive sulfides of the Zenith-Victoria field distinguishes three major stages of evolution: initial, interim and final represented by Fe-S, Cu-Fe and Zn-Fe types of SMS respectively /3/. In this talk, we describe the results of geochemical analysis of massive sulfides from the Zenith-Victoria field. Geochemical varieties of SMS are considered to be indicators of the evolutionary stages of the hydrothermal system."

Sep 1, 2014

By Simon Strong, Tim Brown, Luis Ignacio Sanz Vivanco

"One of the most significant technical and practical challenges facing the tunnel construction team on the Legacy Way road tunnel project in Brisbane, Australia was how to erect the pre-stressed precast concrete slabs to form the smoke duct in the tunnel boring machine (TBM) tunnels. An essential part of the tunnel ventilation system, the smoke duct, extends the full length of the 4.6km long twin, two lane tunnels. The vast majority of the tunnels (approx. 4.3km) were constructed using two 12.4m diameter double shield TBMs. The refurbished Herrenknecht machines broke several world records on the way to completing the tunnel excavation works in just over nine months. With the excavation complete the focus turned to solving the complex civil tunnel fit out challenges. A key component of the civil fit out of the tunnels was constructing the smoke duct in the TBM tunnels which was designed as a precast solution. The slabs which each measure 8.62m long by 2.0m wide by 200mm thick and weigh close to 9 tonne need to be erected above cast in situ corbels whilst other tunnel finishing works continue. The space proofing clearance offered by the design to the support corbels below and the precast segmental lining above was in the order of only 100mm. This paper details the events of how the Transcity JV tunnel fit out team, comprising some of Europe and Australia’s leading tunnel construction specialists, drew upon the global strengths of the existing JV member companies and the global reach of leading TBM manufacturer Herrenknecht to develop an innovative system to solve this challenging problem. This globetrotting story, which starts in Australia, visits Europe and mainland China before returning to Brisbane where it all began."

Jan 1, 2016

By Erika Moonin, Jim Nickerson, Claudio Cimiotti, Roberto Bono

"In response to the severe drought on the Colorado River basin and in order to preserve existing water capacity to the Las Vegas Valley, the Southern Nevada Water Authority contracted a new deep-water intake (Intake No. 3) located in Lake Mead. The current project (Contract No. 070F-01-C1) includes 5 km (3 miles) of tunnel with very difficult geological conditions and a 200- m (650-ft) deep shaft and marine works. This paper will present the current status of the design-build contract being constructed by Vegas Tunnel Constructors and the challenges and problems faced and the innovative solutions developed to handle the difficult conditions encountered during tunneling with up to 15 bars of pressure.ProjectbackgroundThe Las Vegas Valley receives the majority of its water from Lake Mead, which is located approximately 30 km (20 miles) east of the Las Vegas, NV metropolitan area. Due to the severe drought that has hit the southwest region of the United States, the water level in Lake Mead has receded from its high water level of 372 m (1,221 ft) above mean sea level (amsl) to a low of 330 m (1,076 ft) amsl in June 2015. Should the lake level continue to fall, at elevation 320 m (1,050 ft) amsl, the current water intakes will not be able to draw enough water to meet the needs of the local area. The risk of losing water capacity has prompted the construction of a new deeper intake. Not only is the new Intake No. 3 situated at a lower elevation in the lake at 262 m (860 ft) amsl, the new Intake No. 3 is also located to draw better quality (Fig. 1).Project challengesThe project has had several difficult challenges to overcome:• The work consisted of a 1.2 kt (1,300 st) structure constructed on a barge and lowered 100 m (330 ft) into Lake Mead anchored with 9,200 m3 (12,200 cu yd) of tremie concrete.• The drill-and-blast starter tunnel was impacted by three inflow events, resulting in a one-year project delay.• One of the main challenges was selecting the tunnel boring machine (TBM) and excavating the tunnel with expected hydraulic head pressure of as much as 17 bar (16 bar was the highest pressure recorded during the drive), crossing faulted areas, low rock cover and the risk of tunnel instability due to direct connection with the lake.• Extensive pre-excavation grouting with a constant head pressure ranging from 12 bar to 15 bar.• Structural repair of the cutterhead in difficult hydrogeological conditions [water inflow of approx. 800 m3/hr (4,000 gpm)].• Complete repair of the cascade sealing system for the main bearing and two replacements of the pinion bearings.• The TBM approach to the intake structure."

Jan 1, 2015

One of the critical challenges facing the mining industry ? and not just in the United States ? is the looming labor shortage. A significant percentage of the industry?s professional workforce is, well, getting old, and many will be retiring in the next 10 years or so. This is not a new issue to the industry. It has been discussed at various industry meetings and conferences for many years. How does mining, with its largely negative public image, attract young people to mining schools? And, equally important, who is going to teach them? Mining schools, what?s left of them in the United States, are beginning to lose qualified faculty to retirements, and no one is available to replace them. SME addressed this issue during the keynote session at its annual meeting in February in Denver, CO. This year?s theme was ?Mining: It?s About the People.? Despite a blizzard that blanketed the city on the day most attendees were to have arrived, the meeting still attracted a record 7,202 people. And the accompanying exhibit sold 822 booths, also a record. The U.S. Department of Energy?s National Energy Technology Laboratory contracted with the National Academies? National Research Council to complete a study concerning the availability of skilled workers to meet the energy and mineral security requirements for the United States. The National Research Council, in turn, asked SME to collect and analyze workforce trends in these industries. The result of SME?s analysis is the report ?Emerging Workforce Trends in the U.S. Energy and Minerals Industries.? It is available on the SME website, www.smenet.org. Click on Government Affairs. While the report did not paint a completely dismal picture, there were some disturbing results. It concluded that within 20 years there will not be a sufficient number of skilled professionals to satisfy the labor demand. That said, the report said that most of those positions would likely be filled. However, the U.S. mining will go through a period of time when the workforce will be made up of very young and senior workers.

Jun 1, 2013

By Charles H. Greene

This paper will describe briefly the steps taken in the development of a Central Florida phosphate ore deposit from acquisition to mining. Further, the design and early operation of the mining and beneficiation facilities will be depicted. During the 1950's, with confidence in the continually increasing requirement for phosphate fertilizer materials essential for producing food, I'. R. Grace & Cc acquired the Hookers Prairie tract containing approximately 45 million metric tons o. (50 million short ton~ of potential phosphate rock product. In 1973, at a point when the Grace captive need for rock was being greatly enlarged by a planned doubling of its Bartow phosphate chemicals plant capacity, the decision was made to expand existing phosphate rock production by building a new mine and plant. The initial annual capacity was to be 2.3 million tons (2.5 million st); however, subsequent investigation pointed to a higher than estimated dragline operating factor 'and the forecast of annual capacity was set at 2.5 million tons (2.8 million st).

Jan 1, 1977

By V. Ramirez, M. Mankosa, G. Luttrell, E. Wasmund

"The performance of column flotation is strongly influenced by the effectiveness of the gas sparging system. Unfortunately, field studies suggest that gas injector systems used for column sparging are not always optimized. This unfavorable condition can create a number of issues within the concentrator including lower recoveries, poorer metallurgical upgrading, decreased capacities, increased circulating loads, higher reagent consumption and inefficient energy usage. To help overcome these problems, techniques have been developed that can be adopted by plant operators to improve sparger performance. These techniques include (i) design modifications to sparger components such as nozzles, distributors and internal parts and (ii) operational improvements such as proper balancing of gas/water flows, elimination of unnecessary pressure drops, and staged injection of frothing agents. This article reviews the important criteria that govern sparger operation and provides data showing how simple low-cost improvements can positively impact column performance. INTRODUCTION Column flotation cells have become the most popular machine design for industrial applications that require high purity concentrates. The superior metallurgical performance of column cells can be largely attributed to their unique geometry, which readily accommodates the use of froth washing systems. The wash water minimizes the nonselective entrainment of ultrafine gangue minerals that would otherwise be hydraulically carried in the water reporting to the froth concentrate. The larger height-to-diameter ratio of columns allows a deep froth to be maintained, which is essential to achieve even water distribution. Due to these unique features, column cells can provide impressive levels of metallurgical performance closely approaching the ultimate separation curve predicted using the flotation release analysis method (Kohmuench et al., 2007). Another very important feature of column cells is the design of the gas sparging system. One popular choice in the minerals processing industry is the Eriez SlamJet® sparger. As shown in Figure 1, this type of sparger operates by passing compressed gas through a small discharge nozzle. Fluid turbulence created by the exiting gas disperses and distributes small bubbles into the flotation pulp. The sparger is equipped with an internal moveable rod that is attached to a pressure diaphragm in the back housing of the sparger. The internal rod automatically moves back/forward and opens/closes the nozzle outlet when the compressed gas is switched on/off. This patented design effectively eliminates the accidental backflow of flotation pulp into the injection tube during shutdowns. The sparger can be operated as a gas-only injector or with the introduction of a small amount of high-pressure sparger water (Kohmuench et al., 2010)."

Jan 1, 2016

By M. Westendorf, T. Banerjee, S. Kaushik, D. Tinney

"Cyclones are one of the most extensively used pieces of equipment within the mineral processing industry because of their simplistic operating and maintenance philosophies. They are commonly used as classifiers within the comminution circuit to control the grinding product particle size for satisfactory performance of downstream operations.Cyclones are a key contributor to the effective operation of the plant and have a significant impact on the mineral processing plant operations. If the cyclones are not performing as they should, the results are often a combination of lost recovery, grade, capacity and reduced throughput. Similarly, an inefficient cyclone operation may also lead to low or high recirculating loads that impact the efficiency of the comminution circuit. This highlights the importance of having proper stability in cyclone operation while implementing any plant-wide optimization strategy.One of the key challenges in cyclone operation is that cyclones are highly sensitive to changes in operating conditions and are affected by process fluctuations such as feed pressure, solids concentration and flow rates. Fluctuations in cyclone feed characteristics lead to unstable cyclone performance which affects mineral liberation. For such an impactful unit operation, cyclones have historically been under-instrumented in an otherwise highly instrumented process plant. Traditionally, mill operators have relied on visual observations of the apex discharge to determine the operating state of the cyclones. Visual cues corresponding to the different cyclone operating conditions have been discussed by Neesse et al. (2004) as shown in Fig. 1."

Jan 1, 2014

By John D. Hanifin, C. Kevin Moon, Eric C. Wang

Value Engineering on Connecticut DOT’s Walk Bridge selected the trenchless option for utility relocation to address the channel crossing’s environmental concerns. The design and construction considerations of the twin micro-tunnel drives and associated shafts are presented. Key challenges included vertical alignment selection to achieve minimum one-tunnel diameter stable cover within thin glacial till underlying extremely soft clay, limited choice of pipe and joint materials meeting stringent non-metallic conduit requirements, thermal grout backfill application, and the close proximity of temporary trestle piles. Mitigation measures were developed for potential point loading pipe damage from remnant boulder fragments in the annular space.

Dec 1, 2022

By Ted DePooter, Mun Wei Leong, Chad Frederick

Downtown Bellevue Tunnel (DBT) is part of Sound Transit’s $3.7 billion, 14-mile light rail transit system from downtown Seattle, across Lake Washington, to the cities of Mercer Island, Bellevue, and Redmond. The tunnel was the first Sound Transit East Link project and posed significant construction risk. This paper discusses implementation of design changes to the soft ground tunneling method, implementation of several technologies such as the use macro-synthetic fiber initial shotcrete lining, use of spray-applied waterproofing, and use of shotcrete for the final tunnel lining. These efforts allowed for significant time and cost savings to the project.

Jun 13, 2021

By Ralf Plinninger, Pafos Busch, Richard Gradnik

This paper presents the details of the Bad Bergzabern tunnel project. This tunnel is the main part of the B427 federal road bypass, intended to improve the regional traffic infrastructure and to reduce the traffic load in the historic city centre of the health resort Bad Bergzabern. Located in the south-western part of Germany, the project area is situated at the eastern margin of the so-called Palatinate Forest, a low mountain region of mainly triassic sediments with a complex and variable geological history. The German federal government, represented by the office of mobility of Rhineland- Palatinate, awarded the contract to BeMo Tunnelling, a specialized Tunnelling company with a long history of innovation and success in NATM tunnelling. The contract includes the construction of two separate tubes with a length of approximately 1,44 km (0.9 mi)—the road (main) tunnel with a cross section of 101 m2 (1,090 sq ft) and a parallel rescue tunnel with a cross section of ca. 23 m2 (250 sq ft.) Both are connected by six cross passages. Tunnels and cross passages are excavated according to the principles of the New Austrian Tunnelling Method (NATM). Due to BeMo Tunnelling’s technical expertise and capabilities, the project team was able to engineer a speed-up concept that saves money and time for the construction team and client. This paper presents the innovative approach BeMo Tunnelling made to optimize the execution of the tunnelling works and the challenges the project team is facing with regard to a complicated geological situation, countermeasures against an increasing effect of climate change and volatile prices for construction materials.

Jun 13, 2023

By O. Porterfield, M. O’Kane, M. Endersby

BHP Iron Ore initiated research programs in January 1995 to develop long-term plans for decommissioning waste rock material at its Mt. Whaleback operation. More than 2 Gt (2.2 billion st) of waste rock were deposited during the past 30 years. Ultimately, a total of 4 Gt (4.4 billion st) will be deposited in waste rock dumps constructed near the open pit. The Mt. Whaleback operation is located in a semiarid climate adjacent to Newman, Western Australia. The primary research program includes the development of technology for the long-term performance of the waste rock dumps with respect to vegetation, slope stability, surface runoff, erosion and water infiltration. This paper focuses on the design and implementation of a cover system to prevent water infiltration to the underlying waste rock. Data obtained from a laboratory program and from soil-atmosphere modeling was used to design horizontal field test plots. The construction of the horizontal surface field test plots is discussed together with the field instruments installed to monitor performance. The cover system is designed to maximize infiltration during wet periods for subsequent evapotranspiration while minimizing surface runoff. The result is a near-zero net infiltration to the underlying waste material. An important feature of the design is the use of run-of-mine waste material as the cover material. Monitoring is in progress and will continue for at least two annual wet/dry cycles. The optimum cover system should minimize the net infiltration of water to the underlying waste rock while maintaining physical and ecological integrity for long-term performance.

Jan 1, 2000

By G. T. Austin

This is an overview of the gemstone industry with special attention on particular states within the united states. The U.S. Bureau of Mines, Department of the Interior compiled and analyzed the information contained in this report. The report should be viewed as a current "still photograph" of a dynamic system. The information presented on a specific gemstone or for a specific state can and will change with time. This overview presents historical and reference information on the principal gemstones and their production in certain states. The report is not a definitive work on gemstones within the select states or United states.

Jan 1, 1995