Search Documents

By J. G. Groppo

Lowering of filter cake moisture of ultra-fine coal to a 20 percent level using conventional vacuum filtration could be achieved using a combination of metal ion and surfactants. Pretreating coal slurry with about 0.2 Kg/ton of a surfactant and 50 ppm of copper or 10 ppm of aluminum ions provided filter cake containing 22.8 percent moisture. The lowering of moisture is explained due to formation of hydrophobic micro-agglomerates which facilitates dewatering.

Jan 1, 1994

By J. Bacho

The modern drilling fluids industry is a dynamic, evolutionary environment. It is continuously striving to satisfy and anticipate the ever-changing needs of the oil and gas industry. The predominant driving forces in the industry over the past decade have changed dramatically. Health and environmental issues, coupled with economic and performance requirements, demand innovation and change from the drilling fluids industry. Emerging drilling fluid technologies will demand environmental considerations from mined components with additional emphasis on cost and performance criteria. Drilling fluids providers continue to search for and identify environmentally sensitive components which meet or exceed the performance of their more toxic predecessors. These changes have and will impact the components of drilling fluids that are mined.

Jan 1, 1994

By G. T. Homce

Most electric motor predictive maintenance methods have drawbacks that limit their effectiveness in the mining environment. The U.S. Bureau of Mines is developing an alternative approach to detect winding insulation breakdown in advance of complete motor failure. In order to evaluate the analysis algorithms necessary for this approach, the USBM has designed and installed a system to monitor 120 electric motors in a coal preparation plant. The computer-based experimental system continuously gathers, stores, and analyzes electrical parameters for each motor. The results are then correlated to data from conventional motor-maintenance methods and in-service failures to determine if the analysis algorithms can detect signs of insulation deterioration and impending failure. This paper describes system design and implementation. At this writing, however, installation is still underway, and field data analysis results are not yet available.

Jan 1, 1994

By M. Younis, E. Comis

"The success of a tunnel project relies on many factors, but one of the most important is also the most overlooked: coordination by all parties involved during the design stages. This is particularly true of segment design and TBM design. Tunnel lining with segmental rings is usually designed according to the standards of reinforced concrete construction based on a given GBR. However, for TBM tunneling, the determination of loads during ring erection, advance of the TBM, earth pressure, and bedding of the articulated ring are all part of the tunnel lining design as well. TBM design can be heavily affected by the segment arrangement, dimension, and weight, but these are usually given as a fixed input to the TBM manufacturer—a process that can cause unnecessary complications. The authors propose that the industry evaluate the process as it stands. In order to find the optimum balance between lining design and TBM cost and operational workflow, both designs should be finalized concurrently. This requires coordination between the TBM manufacturer and segment designer from the early stages. The aim of this paper is to evaluate the influence of the segment lining design on TBM cost and performance, and to provide commentary on existing design guidelines to optimize lining and TBM procurement. INTRODUCTION The conventional project setup for tunnel lining design and the design and manufacture of the tunnel boring machine (TBM) should be coordinated in a timelier manner. It is widely acknowledged that the design of segments must consider the forces exerted by TBM rams during tunnel construction, but other inputs are most frequently provided to the TBM manufacturer as fixed parameters to design around. This paper describes other important factors in TBM design that impact not only the interaction with the segments, but also the construction of the tunnel in terms of overall production and even safety. For example, the segment width and tapering have direct influence on shield body length and thrust cylinder size. Furthermore, TBM geometry can also affect the backup (trailing gear) layout and length."

Jan 1, 2016

By Loic Galisson

"Urban tunneling projects are usually extensively monitored. Most of the instruments used rely on benchmarks providing a sustainable datum throughout the life of the project. The monitoring program also is based on a predicted model of deformation induced by specific construction methods. Events can interfere with those assumptions and eventually alter the stability of these datum. In addition, the anticipated ground conditions and hence the theoretical deformation model often differ from reality. Satellite Radar Interferometry provides useful information to overcome the weakness of the hypothesis made before construction. It is also a powerful tool to ensure the continuity of the monitoring program throughout the life of the project, accurately describing the true effect of the project on the surrounding environment. This paper emphasizes the benefits and limitations of this technique for urban tunneling applications, illustrated by examples of major tunneling projects around the world. MONITORING URBAN TUNNEL PROJECTS Why Monitoring? Retrofitting existing tunnels or constructing new tunnels – including access and retrieval shafts, portals and cross passages – implies an alteration of the neighboring soil structure. Excavating, dewatering, grouting, loading tie backs, etc. artificially modifies the natural equilibrium of the pore-water pressure, of the water table level and of soil stability. In many cases, the effects are immediate: ground loss, deformation of utilities, settlements of buildings, and distortion of infrastructure are a few examples resulting from construction activity.Instrumentation and Monitoring Scope To control and mitigate the risks of damage associated with the above effects, tunnel projects usually include an instrumentation and monitoring program. Depending on the level of geotechnical, structural and environmental risk, the magnitude of this program varies. Projects with a low exposure to risk may restrain the program to conventional methods such as limited topographical surveys and intermittent manual readings of geotechnical instruments. On the other hand, iconic projects with high risk or with controversial history may implement complex and extensive instrumentation plans, involving highly technical solutions such as Automated Motorized Total Stations (AMTS – see opposite Picture 1), Multi-Point Borehole Extensometers (MPBX), In-Place Inclinometers (IPI) and a wide series of fully automated geotechnical, structural and environmental sensors. In this case, all the devices are usually connected to field data loggers collecting raw data around the clock at frequencies ranging from days to seconds, depending on the sensors."

Jan 1, 2016

By T. Harris

Exports of crude gypsum from Mexico currently comprise about 60% of all domestic shipments, and about 25% of the imported material consumed in the U.S. wallboard industry. However, of growing importance are the domestic markets for calcined gypsum in Mexico including building plasters and wallboard, which account for 55% of the internal demand for natural mined material. This paper will examine the current trends in the production and trade of natural mined gypsum in Mexico and North America and the opportunities and threats that are facing existing and new suppliers in this changing market.

Jan 1, 1996

By Kadri Dagdelen

New underground coal mines have become increasingly expensive to open. A simple drift mine producing a raw coal product can cost as much as $50 million while a new shaft mine producing a washed coal product can cost up to $200 million. As a result, few if any speculative new mines are constructed. Normally, a long term coal supply agreement is needed to justify new mine projects. Negotiating a supply agreement prior to production start is difficult. Pricing must be based on estimated rather than historic costs and coal quality must be estimated from core hole samples versus actual shipments. Further in todays competitive coal markets, there is little margin for error in either price or quality.

Jan 1, 1983

By D. Gatzemeier

The Jewett mine is a surface mine in central Texas, producing about 8,000,000 tons/year of lignite. The mine covers 46,000 acres of land. Approximately 430 people are employed by Northwestern Resources Company and through their efforts, the Jewett Mine is one of the most productive mining operations in the country. The Jewett Mine utilizes a unique structure of staff to convert Operations Research into plans which can be implemented at the "front line" level of the Operations Team. This planning not only makes the mine cost effective and efficient, but promotes creativity in mining, which promotes ongoing research to lower the cost of mining.

Jan 1, 1993

By John E. Dreier

The Pachuca-Real Del Monte district, Hidalgo, Mexico (Figure 1) has produced roughly 1,500,000,000 oz Ag., 6,000,000 oz Au. and minor Pb., Zn, and Cu from about 100,000,000 tons of ore since discovery early in the 16th century. Production has come from epithermal vein deposits that have been up to 8 km in length, 650 m in vertical extent and 45 m in width but which averaged 200-400 m in length and vertical extent and 2-4 m in width. Ore deposits occur through-out an area about 12 km E-W by 10 km N-S (Figure 2) and between the elevations of 2000 and 2800 m above sea level. The deposits occur as shoots in the veins and terminate laterally where the veins narrow, upward where the veins pinch out and downward where the veins decrease in silver con-tent to below the cut-off grade; the veins are known to extend 500 m below the bottoms of the ore bodies and probably extend to much greater depths. The district lies wholly within a mid-to-late Tertiary volcanic rock sequence that is made up principally of andesite and dacite lava flows and flow-breccias. Although the bottom of the sequence is not exposed in the district, stratigraphic constructions indicate the volcanic rocks to have an aggregate thickness of 2000 to 2500 m. Structurally, the area is characterized by gentil warping and normal faulting of the volcanic rocks. Pre-ore modifications to the volcanic rock sequence consisted mainly of faulting along west-trending, south-dipping normal faults and north-trending high-angle faults.

Jan 1, 1978

By R. D. Cook, J. L. Johnson

"Measuring mud bed level in a sedimentation device is an important control variable. Methods used to date for this purpose have had limited success providing continuous, consistent measurements at a reasonable price. This paper describes a new instrument for detecting the mud bed / liquor interface as well as bed density profiles. The state of the bed is measured directly with sensors located in the thickener. Data from bench-scale and full-scale tests show that the bed level is well defined and easily detected. In addition, full-scale testing revealed unprecedented information about thickener beds. Variation in bed density gave new insight into thickener bed dynamics, providing design and control opportunities never before possible. This novel instrument can significantly improve thickener control by providing reliable and consistent bed level measurements. It is also capable of measuring bed density profiles that can potentially identify significant operating problems early enough to take corrective action before experiencing costly shut downs. INTRODUCTION Numerous studies and papers have been devoted to the subject of thickener design and operation to achieve specified throughput and discharge densities. Mathematical models have been developed that present methods for sizing thickeners and predicting performance under varying process conditions. The compression effect of deeper beds on dewatering performance is a recognized phenomenon (Wilhelm and Naide 1981). This is one variable of many that are inter-related and influence thickener performance. For example in the steady-state, continuous operation of a thickener, if the solids feed rate increases and the bed level remains the same, the underflow discharge rate must increase with the result of solids concentration being lower. The interactions of these parameters are at the heart of thickener models. One such model (Burger and Narvaez 2007), predicts solids concentration profiles increasing downward and discontinuities between settling zones. This model uses sediment height (bed level) as a parameter that influences capacity calculations to achieve the specified solids concentration of the underflow. Knowing the bed depth is critical to maintaining stable thickener operation. Implicit in these modeling strategies are some basic assumptions such as homogeneous distribution of solids in the different settling zones, plug flow of solids through the settling zones and steady state operation of the thickener. The accuracy of these assumptions has not been verified because there has been little visibility inside the bed of full size operating thickeners. Testing of the instrument presented in this paper demonstrates that it provides a degree of visibility of the dynamics in a thickener not previously possible and indicates that the basic assumptions of the modeling strategies may not be completely accurate."

Jan 1, 2015

This United States Bureau of Mines study is based on a review of U.S. mine fire accidents that occurred from 1970 through 1989. Information on these accidents was obtained through investigative reports written by Mine Safety and Health Administration personnel. For this study, 260 mine fire accident reports were examined. A previous Bureau research effort established that fires causing fatalities were more likely to occur in haulage entries than at any other underground location. This study has found that the most prolific source of haulage entry fires was the inadvertent grounding of trolley wires. The largest segment (15 out of 40 trolley wire fires) resulted from not maintaining adequate clearance between the trolley wire and the vehicle. Several novel fire prevention and control ideas have evolved in response to frequently occurring fire-related problems. These included; discriminating power isolation devices, wire cutting devices, more accessible fire extinguishers, vehicle overcurrent protection, and vehicle fire suppression.

Jan 1, 1994

By Stephen W. Denton

Planning a mining operation in Alaska will involve the investigation of many parameters common to mine planning anywhere. However, there are some unique circumstances that must be recognized when one considers development of mining operations in Alaska. This paper will not attempt to provide a blueprint for mine planning in Alaska, but hopefully will provide a better understanding of the truly unique nature of the northern latitudes. Given this understanding, the mine planner can better assess the potential hurdles along the road to a successful mining operation. The regulatory trend towards uniform standards for mining throughout the United States exemplifies the necessity for Alaska to prove its unique position in the natural resources picture. The factors which make Alaska truly different from the "Lower 48" can be summarized by four points 1) Remoteness and Size 2) Seasonable Extremes 3) Geologic Immaturity 4) Vegetation and Wildlife

Jan 1, 1984

By S. B. Hildebrand

One of the highest costs associated with insitu leaching of copper is electric power. The ReGeneration Project addressed this cost issue with a research and development project for BHP Copper. The project involved the installation of a reverse pump/turbine for the removal of excessive fluid pressure and the production of useful electric power. The motivation for the project was that a reverse pump/turbine unit could not only remove the excess hydraulic pressure, but when connected to an induction .generator, would produce electric power, which could be easily connected to the local power gird, thus reducing operating costs. The project was successful in removing excess fluid pressure and producing electricity. The unit is operating today, producing useful 2,300 volt power at a rate of approximately 128 kilowatts.

Jan 1, 1998

By Frank E. Chase

Preventing pillar squeezes, massive pillar collapses, and bumps is critical to the safe and efficient recovery of coal during room-and-pillar retreat mining. To help prevent these problems, the U.S. Bureau of Mines (USBM) has developed the Analysis of Retreat Mining Pillar Stability (ARMPS) computer program. ARMPS calculates stability factors (SF) based on estimates of the loads applied to and the load-bearing capacities of, pillars during retreat mining operations. The program can model the significant features of most retreat mining layouts, including angled crosscuts, varied spacings between entries, barrier pillars between the active section and old (side) gobs, and slab cuts in the barriers on retreat. It also features a pillar strength formula that considers the greater strength of rectangular pillars. The program may be used to evaluate bleeder designs as well as active workings. A data base of 110 pillar retreat mining case histories has been collected across the United States to verify the program. It was found that satisfactory conditions were very rare when the ARMPS SF was less than 0.75. Conversely, very few unsatisfactory designs were found where the ARMPS SF was greater than 1. 5.

Jan 1, 1995

By Mark E. Gershon

The development of long term plans and schedules for strip mines now faces many companies, especially those developing large properties in the West. The rule of mining the lowest strip ratios first, while delaying equipment acquisitions and recouping investment the fastest, creates the situation where stripping ratios are too high in the latter years of mining operations. A program concept taking life of mine return on investment into account is developed in this paper to optimize mine scheduling and equipment acquisition. In addition, quality considerations (heat content, ash, sulfur, washability) can be considered by including the appropriate blending constraints to meet contract requirements.

Jan 1, 1983

By Howard G. Coopersmith

A resource of low grade good quality diamonds has been discovered through the Diamond Company NL-Moonstone Diamond Corp. Joint Venture. A limited bulk sample diamond test of two large kimberlite pipes on the Kelsey Lake Property, Colorado, has been completed. These kimberlite pipes have petrological and mineralogical indications of the presence of diamond. Small diamonds were recovered from surface samples. Drilling and trenching revealed both pipes were complexes of diatreme facies kimberlite. One pipe contains crater facies kimberlite as well. This is the first reported occurrence of crater facies kimberlite in the Province. Approximately 1000 tonnes of kimberlite rock was excavated and processed through a scrubber -HMS -Sortex -Grease Plant. Significant diamonds were recovered. The diamonds were generally of good color and clarity, with many being in the gem and near gem categories. Grades are considered low however. Additionally, a small potential resource of alluvial diamonds is present.

Jan 1, 1991

By K. Hanna

Early identification of adverse geologic conditions and high stress concentrations during the high-speed extraction of coal using modern mechanized long wall systems is a major challenge facing the mining industry. Often, unexpected geologic anomalies that affect rock mass quality are encountered more rapidly, leaving the mine operator with insufficient time or information to deal with the changing ground conditions. The RockVision3DTM seismic tomographic system, developed by NSA Engineering, Inc., offers substantial benefits over conventional geologic/stress-detection methods and has been used successfully in coal mines worldwide. Tomographic images, produced economically and in near-real time, are easy to interpret, allowing mine operators to deal with potential hazards on a day-to-day basis. This paper focuses on the application of RockVision3DTM technology for delineating hazards caused by stress and geologic anomalies. Case studies for two bump-prone coal mines will be discussed. For example, (1) in a German deep (>1,130 m) mine, the drilling-yield method was used to verify the effectiveness of this technology in detecting stress anomalies ahead of longwalling; (2) in a Polish mine (-500 m deep), two longwall panels 4 km apart were monitored to assess structural and stress-related factors contributing to differences in mining conditions and magnitude of structural failures.

Jan 1, 1999

By Faruk Oksuz, Dave Schiemann, Miguel Sanchez, Patrick Jensen

"The McCook Main Tunnel connects Chicago’s Tunnel and Reservoir Plan (TARP) Mainstream Tunnel to the McCook Reservoir. The tunnel system consists of a 10 m (33 ft) finished diameter and 490-m (1,600-ft) long hard-rock tunnel constructed from a 27.5-m (90-ft) diameter and 92 m (300 ft) deep main gate shaft. The gate shaft houses six high-head 4.4 x 9 m (14.5 x 29.5 ft) wheel gates installed in the bifurcated and steel-lined section of the tunnel. The tunnel also includes portal and energy dissipation structures as it daylights into the reservoir. Construction of the McCook Main Tunnel in live flow conditions was a challenging task for the McCook Main Tunnel Project participants, the project owner U.S. Army Corps of Engineers (USACE), local sponsor Metropolitan Water Reclamation District (MWRD) of Greater Chicago, designer Black & Veatch and contractor Kiewit Infrastructure Co. (Kiewit). Once completed in two stages in 2017 and 2029, the McCook Reservoir will hold 38 billion L (10 billion gal) of combined sewer overflows (CSO) and flood waters from the city of Chicago and 36 surrounding communities in Cook County, IL The construction of the tunnel system was divided into two contracts. The first contract for the gate and construction access shaft was completed in August 2011. The second contract included tunnel excavation and concrete and steel lining that was completed in September 2014; installation of gates and hydraulic cylinders that was completed in June 2017; and the last major construction activity was the removal of a temporary concrete plug (bulkhead) and lining that tunnel section to bring the overall tunnel and gates system online before Dec. 31, 2017.This article focuses on the installation, testing and commissioning of the high head wheel gates. Live tunnel connection details to TARP Mainstream Tunnel were addressed in a previous paper submitted at the World Tunneling Conference in 2016."

Mar 1, 2019

By C. J. Hunter

Prior to the commissioning of the Sansu Sulphide Treatment Plant (STP), Ashanti Goldfields' treatment facilities were capable of producing some 700 000 ounces of gold per annum. Ore sources were underground refractory sulphides, surface oxides and old tailings dams. In order to increase the mines production to 1 million ounces per annum and to accommodate the change in ore sources as surface mining moved into fresh sulphides, a part of the strategy adopted was -the construction of a new sulphide treatment plant with a capacity to mill 2.2 million tonnes per annum and produce 400 000 ounces of gold. The STP has been designed, built and commissioned. and has been in operation since February 1994. The Plant boasts the world's largest Bio-oxidation facility which is capable of treating 790 tonnes of sulphide concentrate per day at a grade of 11.4% sulphur and is currently undergoing an expansion to increase its capacity to 1050 tonnes per day. The following sections describe the reasons for selecting the BioX® Process, the plant design, the commissioning experience and the plant performance to date.

Jan 1, 1996

By D. P. Caplice

On behalf of the Ontario Water Resources Commission, I would like to express my sincere appreciation to your Institute for presenting us with this opportunity to outline the regulatory control programme as it relates to the mining industry in the Province of Ontario. In Canada, and particularly in Ontario, we are blessed with an abundance of natural resources. Fresh water in the form of lakes and rivers covers nearly 17 per cent of the area of the Province. (Total area of the Province of Ontario is 412,582 square miles.) The mining industry, which had its beginning in the early 1800's with a small iron ore plant, has progressed with the major discoveries of nickel and copper in 1883, silver in 1903, gold in 1908, iron in 1939 and uranium in 1953, to the point where, in 1966, almost one billion dollars in mineral wealth was mined in Ontario. Water, in spite of its great abundance and with due respects that it may become a natural resource worthy of export in the foreseeable future, has become increasingly precious in Ontario, particularly in the more urban areas in the southern part of the Province.

Jan 1, 1968