Search Documents

By J. Oliver, J. Cleason

"With maintenance costs rising and an increasing demand for higher production, the use of sealed spherical roller bearings can reduce maintenance costs while providing increased production uptime. The sealed spherical bearing has increased bearing life by slowing the ingress of contamination. This paper will describe how contamination and bearing wear is reduced by reviewing case histories from coal and metal mines that improved their production by decreasing downtime using sealed spherical roller bearings. INTRODUCTION The spherical roller bearing (SRB) is a robust rolling element bearing that can accommodate high radial loads, low to moderate axial loads, and misalignment with no loss in carrying capacity. (i.e. Figure 1) Because of these characteristics, it is a favorite in mining applications and many other heavy industry applications. Primary applications are the various pulleys on conveyors. Coal and hard rock mines have hundreds of miles of conveyor lines and countless head, tail, drive, and idler pulleys. Maintaining the bearings on these pulleys and replacing bearings that have failed can be a huge expense to a mine in components, labor and downtime. Ideally, the bearings are replaced when the pulley is changed out according to the maintenance cycle, about every 4 years. Reality, however, causes the bearings to be changed out every year, or sooner. These premature bearing replacements can cause production shut downs for as long as 8 hours. Conveyor pulleys have been targeted at many mines as the single biggest maintenance pain point.The primary reason for replacing conveyor bearings is internal wear from fine, solid particle and water ingress through the bearing housing seals. (i.e. Figures 2 & 3) Traditionally, the bearing is mounted in a split pillow block housing (SAF, FSAF, SDAF or SNL are typical industry styles) with only labyrinth seals (LER/LOR) for protection against the ingress of contaminants. The bearings are lubricated with grease. A common way to extend the MTBR is to purge the bearing system with large quantities of grease to flush out the contaminants. If the bearing, and thus the housing seals are not frequently purged with grease, fine solid contaminants enter the housing and bearing through the labyrinth cavities."

Jan 1, 2015

By F. Schreiter

"One method to increase the exploitation rate of a mine is the use of backfill with residual materials in exploited areas. The backfilled material is meant to support both, the walls of galleries and pillars as well as the roof of mining openings. With increasing depth, the exploitation rate diminishes fast, thus the application of backfill in order to change the layout of the mine is crucial for economic success. In result of using backfill, it is possible to change the layout of the working area with a higher ratio to excavated areas and less area occupied by pillars. Thus it is possible to boost the output of a mine by using backfill. Setting the criteria for the selection of the best possible materials and whose improvement, it is useful to know about their qualities and handicaps. The Mining Department at TU Bergakademie Freiberg is analyzing the parameters of residues from different processing methods, accrued in plants of different potash mines and blending different residues for optimization of material attributes. These were significantly characterized by basically parameters like the size and the distribution of different diameters of the grain material. INTRODUCTION The chair for underground mining methods at TU Bergakademie Freiberg is tasked with the sufficient and sustainable supply of economics with raw materials. The steady high demand, the rising prices and the finiteness of the deposits are reasons for the need of an optimized economic utilization of natural deposits, a continuous improvement of mining technics and technology. From an ecological and economical position the best possible utilization of the resources has to be achieved. Many mining operations are by reasons of the deposit not able to haul valuable minerals only, they have to haul a mixture of valuable minerals and waste rock. This hauled combination is given into the processing plant for separation and enrichment of the valuable mineral. The residuals of the processing are commonly dumped to a waste rock pile. For minimizing the size of such a waste rock pile and also minimizing the ecological footprint of a mining operation the only way is minimizing the quantity of accruing waste rock material. Both, optimization of economic utilization and also minimization of waste rock dumps can be realized in one by backfill with processing waste rock material in mined out areas. Especially in mines, mined by room and pillar method, smaller dimension of the pillars are sufficient for safety and stability. By the way less valuable minerals have to be leaved back in the mine and the mine outcome is increasing."

Jan 1, 2015

By T. Hollingsworth

The Boddington Gold Mine, located near Perth in Western Australia, has recently completed the construction of a new process plant. An overland conveyor system was installed to convey the ore from the primary crusher to the process plant. This paper will discuss the overland conveyor?s mechanical design including dynamic analysis and the selection of primary mechanical and electrical components.

Jan 1, 2010

By G. Keizer

Cortez Gold Mine (C.G.M.) is located in Lander County, Nevada, approximately 80 miles southwest of Elko, Nevada. It is accessed via Nevada State Highway 306 south from Interstate 80. This operation is a joint venture between Placer Dome U. S. Inc. (60% operator) and Kennecott Corporation (40%). The claims which supply oxide and refractory ore feed to the Cortez milling facility are located in both Lander and Eureka Counties. These include the Cortez and Horse Canyon deposits all operated by C.G.M. Joint Venture. Other deposits outside the C.G.M. claim area include; Fire Creek, Buckhorn, Gold Bar and Tonkin Springs. These deposits all occur along the Battle Mountain/Eureka Trend.

Jan 1, 1993

By Don C. White

Santa Rosa is a mid-Tertiary, volcanic-hosted, bulk-mineable, open-pitable, heap-leachable, gold-silver deposit. It is the product of hydrothermal mineralization along an arcuate segment of a caldera collapse ring fault in a probable maar volcanic setting. This segment was later broken by radial faults. Gold occurs principally as electrum finely disseminated through intermediate tuffs, and associated with pyrite, at Santa Rosa. The nearby Alto de la Mina deposit displays stockwork silica-pyrite-gold in a tectonically and hydrothermally shattered andesite flow. Miocene epithermal mineralization was accompanied by central silicification and pyritization and more distal argillization. An andesite flow cap rock at Santa Rosa played a pivotal role as an upward permeability barrier. Highest gold grades and most intense alteration occur closest to the ring faults and immediately beneath the andesite flow. Supergene alteration effects on the gold distribution are minimal.

Jan 1, 1993

By Kim McKnight

Dupont has successfully incorporated a Floatex Density Separator into its wet-gravity operations for the recovery of zircon from titanium tailings. Results indicate that the Floatex achieved a zircon recovery of approximately 95% while rejecting similar amounts of quartz and other gangue minerals. Additionally, a unit capacity approaching 16 tonnes/hr/m2 was achieved. Results also show that the alumino-silicates can be separated into other product streams that will further improve process economics and minimize waste material. The improved plant feed grade provided by the Floatex has allowed for either an increase in overall plant capacity and/or final product grade. This paper will present the findings from the in-plant study.

Jan 1, 1996

By William Gleason

The mining industry is at a crossroads. Currently, there is an estimated $25 billion worth of projects around the world that have been stopped as the consequence of a dispute or disagreement with their communities, the government or some other stakeholder. Anglo American chief executive officer Mark Cutifani is one who sees the mining industry in need of change and on Dec. 12, he gave the keynote address for the launch the Kellogg Innovation Network?s Mining Company of the Future Initiative?s Development Partner Framework (DPF). The launch was held at the Ford Foundation building in New York City. The DPF seeks to inspire and support the mining industry to adopt a new way of thinking and a new approach to how it secures, nurtures and revitalizes its social license to operate. Working with a diverse group of people from faith-based organizations, nongovernmental organizations (NGO) and other stakeholders, Cutifani often had the rather uncomfortable position of representing the mining industry in a room full of people who are far from the industry?s biggest fans.

By C. Sun

Due to unfavorable geological condition, excessive deformation of mine drifts occurred in a large underground copper and nickel mine. In searching for a solution, a comprehensive underground monitoring program was implemented and the opening convergence and the surrounding rock deformation were monitored. A large number of field data were collected and thoroughly analyzed. The convergence and deformation as function of time and depth were determined and a rock stability index was proposed. Based on the deformation-time and deformation-depth relations, critical deformation times and locations were identified and defined as characteristic values to be used for mine opening and support designs. The characteristic values are critical in the application of two-step supporting system, and the determination of support parameters. The application of the method developed in this study has demonstrated that this practical approach in support design and installation is effective. With the two-step supporting system, a long-term drift stability can be achieved in the mine.

Jan 1, 1998

By A. S. Azman

The mining workforce experiences high rates of hazardous noise exposure and hearing loss. However, previous studies have identified specific behavioral and attitudinal barriers that keep miners from effectively acting to prevent their own hearing loss. NIOSH has developed several new hearing loss prevention tools and interventions that specifically target these barriers to prevention. The NIOSH Hearing Loss Simulator addresses motivation to take action and knowledge about the consequences of noise exposure. The QuickFit earplug test device and QuickFitWeb online hearing protection tester address barriers to effective earplug and earmuff use by verifying at least 15 decibels of protection. The NIOSH Roll-Pull-Hold technique helps miners obtain better protection through an easy-to-remember set of steps that improves attenuation by 9 decibels. The ?Inquiring Ears Want to Know? fact sheet helps miners to understand audiograms and to use them to maintain their hearing health. Each of these interventions can be used within the context of a comprehensive hearing loss prevention program.

Jan 1, 2010

By M. S. Celik

Unlike most other minerals, electrokinetic measurements of calcium montmodonite (a clay mineral) and u1exite (a boron mineral) exhibit an unusual behavior. While the addition of monovalent salts such as NaCI and KCI is expected to compress the electrical double layer with a resultant less absolute charge, an opposite trend is observed. A set of systematic experiments with monovalent and multivalent ions has been carried out to understand the mechanism of this phenomenon Examination of the results reveals that the behavior of montmorillonite is dictated by the exchangeable divalent cations at the edges which undergo an exchange process with monovalent cations resulting in the reduction of positive charges. The solubility of ulexite, on the other hand, is found to decrease with increasing monovalent cation concentration leading to again an increase in the absolute negative charge.

Jan 1, 1996

"HISTORY Tube bundle systems have been used in the coal mining industry for gas detection since the 1960’s. At the time there were developments were underway for improved gas monitoring systems. The primary gas detection systems in use were the flame safety lamp, colorimetric stain tubes and the taking of samples for analysis by gas chromatography. The MSA D6 hand held methanometer was approved in the UK for statutory methane measurements in 1972 and became very popular due to its smallness and simplicity of use. In 1973 Sieger Limited also developed a BM1 methanometer which could be installed underground and relay methane concentrations to the surface. Similar developments were underway for carbon monoxide detection and one was developed in 1982 by the Yorkshire Regional Laboratory of the NCB commercial development was undertaken by Sieger Limited who named it the ‘SCO1’. The UNOR 1 carbon monoxide and methane analyzers were approved for underground use in the United Kingdom in the late 1960’s.5 The technique was developed by Dr Luft of Bergbau-Forschung Essen and the equipment was manufactured by Maihak in Germany. The apparatus was flame proof and provided an intrinsically safe output which allowed the result to be telemetered to the surface through colliery communication systems. Both analyzers work on the same principal and each of the gases adsorb a certain wavelengths of infrared radiation. The detector measures the residual transmitted radiation and determines the percentage of gas present in the sample. These flameproof versions had proven to be robust and reliable. The UNOR 1 had been used in the Saar region of Germany and Scotland in the UK. The development of tube bundles for hydraulic controls enabled the development of the tube bundle gas monitoring systems we know today. A bundle of tubes are taken underground through a shaft, a borehole or drift then distributed to the required monitoring points. This enabled the ongoing monitoring of the underground environment when the power was isolated at 1.25% CH4. In 1972 the United Kingdom (UK) National Coal Board (NCB) produced a hand book for tube bundle systems which was subsequently updated in 1974. This is a useful guideline into the operational aspects of tube bundles systems at coal mines6. Many of the processes identified are being followed today. The United State Bureau of Mines (USBM) prepared a circular similar to the NCB handbook on tube bundle systems.7 The circular was prepared by Litton C and it was targeted at the design criteria for tube bundle the systems. The circular also states that “pneumatic monitoring systems can be used to monitor for hazards that develop quite quickly”."

Jan 1, 2016

By A. J. Basu

Computer assisted mine planning and design applications are routinely used by many Australian mining companies, However, the design process requires human expertise to recognize and evaluate the potential pitfalls. This paper introduces the application of a commercial optimization software (WHITTLE 4D) for strategic planning of an open pit mine in Western Australia. The authors present their experience in intelligent application of the optimization program while incorporating many technical and nontechnical obstacles. This paper provides some guidelines on how to apply the optimization software without loosing sight of practicalities. Moreover, this paper also shows how to build project evaluation guidelines for non-experts.

Jan 1, 1997

By B. T. Darnton

Gravity concentration at the Pegasus Gold Montana Tunnels Mine was initiated in late June, 1991 with the commissioning of a coarse gold scalping circuit that processes a small portion of the ball mill circulating load. The primary objective for the circuit was to reduce the risk of gold particles advancing to flotation that are too coarse to float. The secondary objective was to enhance overall gold recovery and payable gold ounces in a cost effective manner. The gravity circuit has proven itself to be a major success. The above mentioned goals have been achieved, and they have been maintained at record throughput rates that are 30% higher than when the circuit was commissioned. A number of modifications and improvements were made over the last three years which allowed the gravity circuit to keep pace with the higher tonnage, these are discussed in detail in the body of this paper. The overall approach to gravity concentration at Montana Tunnels has always been to optimize production rather than maximize the gold ounces produced. This philosophy has now yielded a circuit expansion and relocation project which will allow for an estimated 50% increase in gravity gold production, while reducing the overall unit costs of production significantly. This paper will review historical gravity circuit performance, improvements, and the current relocation and expansion project.

Jan 1, 1995

By L. Bomvisinho

As a result of today?s requirements for larger mills with higher power demand, and in order to cope with maximizing throughput, and optimize grinding efficiency, the minerals industry is increasingly relying on the robust Gearless Mill Drive (GMD) solution. This paper describes the new features introduced with the revolutionary ABB drive controller for Gearless Mills, and explains the benefits this can bring to the operation. Extensive surveys have been performed with GMD users to gather suggestions and understand the market wishes. As a result the new driver controller capabilities and functionalities focus on safety, high availability, operational flexibility and remote diagnostics.

Jan 1, 2010

By H. W. Judges

A 16.5-kt/day underground molybdenum mine is being developed at Questa in Northern New Mexico by Molycorp, Inc., a wholly-owned subsidiary of Union Oil Company of California. Construction of the underground mine began in 1979, and first production is scheduled for early 1983. A gravity block caving method has been selected for mining the ore. Access to the mine will be through a service shaft, development shaft, and a conveyor decline. The shafts are being sunk under contract and the conveyor decline is being driven by Molycorp. The driving of the decline began in February, 1979 with a 10-man mining class. By the first of May, enough men had been trained to begin a continuous operation and by March 1, 1980 the face had reached the 1500 m mark. The heading is being driven with trackless rubber-tired equipment using a three-boom drill jumbo, 2.7 m3 LHD units and 7.3 m3 trucks. Ground support has been by rock bolts and wire mesh, followed by Fibercrete. A 16.5-kt/d underground molybdenum mine is being developed at Questa in northern New Mexico by Molycorp, Inc., a wholly-owned subsidiary of Union Oil Company of California. The new $200-million underground project will revitalize mining and milling activity at Questa, where small scale underground mining first began in 1920. Large scale open-pit mining was initiated in 1965 but now, because of the high stripping ratio, surface mining is being phased out. Construction of the underground mine began in 1979, and first production is scheduled for early 1983. The company expects full capacity - 9 Gg of molybdenum per year - to be reached in 1984.

Jan 1, 1980

By J. M. Ekenes, C. A. Caro

"New approaches that increase hydrometallurgical recovery from refractory minerals in below mill cutoff -grade sulfide copper ore can add significant value, improve profitability and increase ore reserves. This paper describes the development and implementation of an engineered heap (EH) approach to leaching low-grade, chalcopyritebearing ore at Freeport-McMoRan’s mine in Morenci, AZ. The technical evolution of the engineered heap concept is described together with the challenges and benefits following implementation. Introduction The Morenci ore deposit, located in eastern Arizona, has been mined for copper for 140 years. Mineralization in the Morenci district consists of sulfides and oxides. To process these ores, Morenci operates concentrator and leaching circuits. Leaching accounts for two-thirds of the copper produced in Morenci. More than one-half of this leaching-derived copper production comes from run-of-mine (ROM) stockpiles. The largest category of material moved in Morenci is destined for ROM stockpiles and waste dumps. Materials that are not economic to mill or leach are designated “waste.” However, this designation can change based on improvements in extraction technology and commodity prices. Chalcopyrite does not leach well due to its refractory nature. For predominant chalcopyrite mineralized ore, copper recovery during a typical leaching cycle may be as low as 5%. For this reason, chalcopyritedominant ores below mill cutoff grade have historically been classified as waste. By incorporating advanced leaching technology to improve metal recovery from previously leach-resistant ore types such as chalcopyrite, the Morenci Mine has been able to reclassify substantial amounts of this “waste” to “ore.” Process chemistry Chalcopyrite copper extraction is temperature, oxygen and ferric dependent. The temperature is achieved primarily by pyrite oxidation (Eq. (1)) and secondarily by oxidation of chalcopyrite itself (Eq. (2)). The regeneration of ferric in solution can be enhanced by providing the appropriate acid and oxygen levels according to Eq. (3). In the absence of microorganisms, this reaction is very slow."

Jan 1, 2015

By G. Guzman, L. Sevilla, M. Botz

"Newmont Mining Corporation operates the Yanacocha mine in Perú and the gold milling section of the property includes a Sulfidization-Acidification-Recycle-Thickening (SART) plant to remove copper from pregnant leach solution. Since its commissioning in 2008, the plant has been intermittently operated as needed to remove copper upstream of a carbon adsorption circuit. However, starting in 2015 Newmont expects the plant to operate on a more continuous basis in response to higher copper ores that will be processed in the gold mill. In anticipation of this, Newmont conducted a campaign in May 2014 with stockpiled high-copper ore to evaluate performance of the SART plant with elevated levels of copper in feed solution. Results from the campaign demonstrated the SART plant is capable of efficiently treating high-copper leach solution. During the campaign, leach solution copper levels ranged from about 100 to 700 mg/L, and copper removals ranging from about 56% to +99% were achieved. The median copper removal efficiency observed during the campaign was about 94%. The primary plant modification determined necessary following the campaign was the need to improve consistency with sulfide dosing. INTRODUCTION Copper removal from cyanide leach solution can be affected through the addition of sulfide at acidic pH to precipitate copper sulfide as a solid. There has been renewed interest in the process in the past several years due to the increasingly common issue of high copper levels in cyanide leach solutions. The term Sulfidization- Acidification-Recycle-Thickening (SART) is used as an acronym for the process according to the primary unit operations utilized. At a pH of approximately 4.0 to 5.0, the addition of soluble sulfide to a copper-bearing leach solution will result in the precipitation of copper sulfide (Cu2S) solid. The overall acidification and sulfidization reaction is (assuming the use of sulfuric acid for pH adjustment): 2Cu(CN)3-2 + 3H2SO4 + S-2 ? Cu2S(s) + 6HCN(aq) + 3SO4-2 The above reaction is written relative to the copper-cyanide complex 2Cu(CN)3-2, though analogous reactions also take place with the other common copper-cyanide complexes Cu(CN)2- and Cu(CN)4-3. Sulfide in the above reaction (S-2) is normally supplied as sodium hydrosulfide (NaHS) purchased in solid or concentrated liquid form. Two characteristics of this reaction that are beneficial to a leaching operation are: 1. Copper is removed from solution as Cu2S (synthetic chalcocite) solid, which can then be sold to a smelter for its copper value. 2. Cyanide that is complexed with copper in the leach solution is released as free cyanide, thereby regenerating cyanide that can be recycled to the leaching operation for continued use."

Jan 1, 2015

By C. Waddell

PDMI mines five different grades of ore. Shovel operators were experiencing problems differentiating one material type from another. In 1997 PDMI decided to try GPS ore control to aid operators in identifying material boundaries. Computer generated ore control maps and GPS data defining the shovels' position is fed to a computer on board the shovel. A monitor, located near the shovel operator, displays material types, their boundaries, and the shovels' position and movement in relation to the mining face. This information has reduced errors in material identification by 50%.

Jan 1, 1998

By R. K. Mehta

Existing acid mine drainage treatment techniques are not remedial In nature, i.e. though heavy metals can be removed from acid mine water, their presence in tailings and large quantities of these tailings tend to increase capital and operating cost for tailing management. This paper presents the results of a series of systematic tests which finally resulted In the development of the "ferrite" process for mine drainage of coal operations at ambient temperature. The role of pH, temperature, quantity of ferrous salt addition and degree of oxidation is investigated targeting the production of high emu spinel ferrites and effluent water complying regulatory standards with respect to Iron. manganese suspended solids and pH.

Jan 1, 1992

By Fabiola Espinoza Carmona, Elena Chiriotti, Edoardo Misano

"INTRODUCTION Ganntas Tunnel is part of the modernization project of the railway between Alger and Oran, in Algeria. In order to double and rectify the existing line between El Affroun and Khémis Miliana, the alignment foresees the excavation of a 7 km-long twin tunnel. The excavation works started in June 2011 with the contractor CCECC, under the supervision of SYSTRA. Excavation is driven in conventional method by hydraulic hammer simultaneously on 8 different faces since excavation was started also from a junction window towards the middle of the tunnel. The minimum longitudinal distance to be respected between two contiguous tunnel faces has been set to 30 m. The tunnel cross-section is a 70 m² oval shaped profile, temporary support consists of shotcrete, bolts and steel ribs. A 30 to 50 cm thick cast in situ concrete final lining has been provided as well. When the tunnel reached a fault zone in soft clayey marls extreme squeezing occurred, works were stopped and re-profiling operations were carried out along more than 100 m. To date, works proceed at slow rate since high convergences are still monitored and completion of works is not expected before December 2016.GEOLOGY The project is located within the Tellian Atlas mountain area, including in particular the Djebel Ganntas massif in between Mitidja and Chleff plains. Djebel Ganntas is characterized by an extensive massif aligned in East-West direction with smooth slopes made of soft clays that emerge in multiple cliffs and ravines. On the top of it, along the edge, a more recent sandstone formation is found. The existing data on the geology did not allow to establish an accurate geological model at tender stage. In-situ investigations allowed at design stage to identify a Quaternary alluvial cover of clays and gravel, followed by a Miocene stratum divided in a sandy top layer and a lower clayey layer. From a structural point of view, geological maps suggest a north direction dip of layers, but the in situ surveys showed that layers were highly folded. The lack of information at tender stage on the structure of the geological series should have triggered an extensive investigation campaign at detailed design stage which did not take place causing serious consequences on costs and time at construction stage."

Jan 1, 2016