Search Documents

By D. Nutakor

This paper presents the results of a study conducted on a slope failure that occurred in the Q7 mining cut at Rio Tinto's Bingham Canyon Mine. The slope failure occurred in a weak rock mass with an estimated rock mass rating of 25%. The failure mechanism was of the circular type, involving ten 15-m (50-ft) benches and covered a total width of 152 m (500 ft). The analysis used Adam Technology's photogrammetric method with a two-dimensional rock fall simulation program (RocFall software) to design a 3-m- (1 0-ft-) high berm located 7 m (24 ft) from the toe of the failed mass. Back and predictive analyses were performed on a cross-section through the slide using Slope/W software, resulting in flattening the interramp angle (IRA) from 44° to 38°. This design modification produced a factor of safety (FOS) of 1.14. Sensitivity analysis involving FOS vs. pore water pressure showed that FOS is sensitive to water saturation. A dewatering system using a series of horizontal holes drilled below the slide and dewatering holes drilled from a drainage gallery has since been established to improve the stability of the slope. Throughout the one-year period since this investigation, no significant slope movement has been detected by the slope stability radar, and mining is in progress below the failure.

Jan 1, 2012

By William Gleason

"The mining industry tends to focus on very large numbers, whether it’s talking in terms of size of deposits, tons of material mined, the equipment used or the dollars spent. The numbers associated with mining projects are often in the hundreds of millions, but sometimes it’s the little things that can have the biggest impact.Take, for example, the Rosemont Copper Project in Arizona. Owned by HudBay Minerals, the Rosemont Copper project, when in production, is expected to be one of the largest copper mines in the United States, accounting for about 10 percent of total copper production with annual production expected to be 110 Mt/a (243 million lbs/year). However, the project is currently mired in a years-long permitting process. At the 2017 SME Arizona Conference in Tucson, AZ, Kathy Arnold, director of environmental and regulatory affairs for Hudbay Minerals, spoke about the project and the efforts to get it into production.She opened her presentation with the unfortunate news that her 2017 presentation would not be that much different than the 2016, 2015 or 2014 presentations she gave to the same conference. That’s because, as of Dec. 4, 2017, the project had been in the permitting process for 3,797 days, more than 10 years. The process began when Rosemont submitted its initial mine plan in 2006 and a revised one in 2017. The official start to Rosemont Copper’s National Environmental Policy Act (NEPA) started in 2008.In June 2017, the project received its Final Record of Decision from the U.S. Forest Service, moving it a step closer to production. Yet it still faces stiff opposition from opponents while it works to secure the Clean Water Act Permit from the U.S. Army Corps of Engineers and to complete its final mine plan of operations.In her presentation, Arnold said the long process taught her many lessons, including approaching things with a different mindset. More than 130 pages worth of public comments have been collected over the years. The concerns expressed range from lighting issues to pavement to preserving land for a jaguar that was spotted on the property and named El Jefe.“A lot of things that people worry about seem to be small things, but we had to have a different mindset and be open-minded to the concerns,” Arnold said. “That is the commitment we made.”"

Jan 1, 2018

By Jeff Mattern

"Slope performance monitoring, dependable operational practices and ongoing collection of geologic data in openpit slopes all provide valuable information for quantifying potential steepening of subsequent slopes. Mining at the Goldstrike openpit has been ongoing since the early 1980s, having its share of slope instabilities. In areas where slopes have remained stable, consideration has been made for potential slope steepening of final walls.While technology can be efficient, interesting for collecting needed data, slope design fundamentals based on that data can be applied to create much added value.With the proper available equipment, steepening of bench face angles via presplit blasting is not an uncommon method for steepening of interramp slope angles. As an alternative at Goldstrike, the commonly used Modified Ritchie Criteria for empirical catch bench width has been adjusted, resulting in quantified, rock-specific formulas for bench width and rock fall berm placement. The result is an inter-ramp slope angle increase of 2° on a 305- m (1,000-ft) high slope, without the necessary purchases and procedural changes that would be required for presplit drilling and blasting. The result has shown significant net benefits through reduction in mined waste tons and an increase in gold reserves.LocationThe Goldstrike openpit is located in the Great Basin, on the northern end of the Carlin Trend gold belt in northeastern Nevada (Fig. 1). The mine has produced more than 1.2 kt (43 million oz) of gold during the past 30 years."

Dec 1, 2018

By Gene M. Handel

Today the world is heavily dependent on petroleum for its energy. In the United States, over 75% of the primary energy used comes from petroleum. Other developed countries are similar. The less developed countries have a lower dependence on petroleum just as the United States did through the early 20th Century. However, these less-developed countries look upon petroleum as one of the primary energy sources for the economic growth required to improve their standard of living. So everyone considers petroleum an essential ingredient in the recipe for the good life. But there is a substantial problem with this recipe, and it is finally getting general recognition. Petroleum is a finite resource, and the world is using it up at a rapid, accelerating rate. Though it won't be exhausted for many decades, the early warnings of ultimate limits have already appeared. The suppliers of the incremental production in the Middle East have threatened to restrict increases in their production rates. And, of course, the short term embargo of four years ago clearly demonstrated the economic impact of reduced access to petroleum as a primary source of energy. World petroleum production will probably peak in. 10 to 15 years and then start declining. When that happens, economics--the allocation of scarce products (also known as the dismal science for obvious reasons)--indicates that the price of petroleum will escalate in real terms. So that's the situation today. We have a serious and growing problem facing us that could substantially alter the quality of our life over the next 25 years. Recognition that the society may face a period of lowered expectations after a long period of upward mobility will be a painful experience, but it is certainly not the moral equivalent of war. And, besides, we have time to take positive actions to avert the most serious consequences. When we consider alternate energy sources, the possibilities are almost endless: coal, oil shale, tar sands, solar, fission, fusion, wind, tides, biomass, etc. Actually, the list is endless because new possibilities are continually being proposed. Of these possibilities, coal uniquely stands out as an attractive substitute for petroleum. Coal can be, and is, burned to generate electricity and provide heat. It can be liquefied to supplement the liquid fuels from petroleum, and it can be gasified for use as synthetic natural gas. Unlike exotic alternate energy such as solar and fusion, coal has successfully been used commercially to produce synthetic fuels. But, the technology does need to be refined and modernized. Thus, coal's role is not to be "America's Ace in the Hole," but to bridge the transition from primary dependence on petroleum for energy to the utopia of renewable sources of energy. But don't be mislead by the prophets--those renewable sources of energy are going to be very, very expensive when they are invented.

Jan 1, 1978

By Harland E. Cofer

A computer-assisted resources and sedimentological study of the Andersonville, Georgia kaolin-bauxite district was begun in 1975 under a grant from the Office of Mineral Resources of the U.S. Geological Survey (Grant # 14-08-1110-G-173). A preliminary report on the kaolin and bauxite resources of the district has been placed on open file at the U.S.G.S. in Reston, Virginia; the Georgia-Geological Survey in Atlanta, Georgia; and Georgia Southwestern College in Americus, Georgia. In addition to a resources estimate, the objectives include the determination of the mineralogical variation, sedimentological parameters, and paleogeographic patterns of the deposition of the high alumina materials and their associated sediments. In the process of compiling data for the resources estimate, isopach maps were developed that provide information as to the shape, size, and distribution of the kaolin deposits and the kaolinitic sediments that contain them. These or similar maps developed for other districts can be useful exploration tools.

Jan 1, 1977

By Kenneth K. Landes

So far my consulting in industrial minerals has been confined principally to carbonate rocks,-salt, coking coal, and glass sand. Much of this work has been for companies either too small for a full-time geological staff or unaware of the value of employing one or more qualified geologists permanently. It gave me considerable personal satisfaction to see several of the latter companies employ one or two full-time geologists after the completion of a consulting contract with them. One possible reason why some companies lack the wisdom to hire geologists is that they are dominated by engineers who still subscribe to the old idea that engineers are self-sufficient in all fields. They could have learned this from their professors. I once knew a Dean of Engineering who got purple in the face when a faculty committee was discussing the financing of a broad gauged engineering project and suggestions were made that assistance be obtained from the Schools of Business and Law and from some of the science departments tie pounded the table and shouted "Engineers are trained to handle all this!" In teaching engineering geology some years ago I used to tell the class repeatedly that the course would not make them geologists, that the purpose was to teach them

Jan 1, 1972

By J. Lorengo, C. H. Bucknam

"Standardization of the Inductively Coupled Plasma Mass Spectrometry (ICPMS) method for gold in cyanide solutions was undertaken to provide a more sensitive method to quantify the gold content than the atomic absorption method standardized in 1994 (E1600). The gold concentration range covered is from 0.001 mg/L Au - 0.3 mg/L Au (0.00005 toz/t Au – 0.009 toz/t Au). Interlaboratory testing was carried out with the assistance of the American Society of Testing and Materials (ASTM) International on two committees to determine the within laboratory and between laboratory reproducibility. Three barren solutions from metallurgical operations were measured in triplicate to satisfy statistical requirements for Committee E1 on Analytical Chemistry of Metals, Ores and Related Materials. A synthetically prepared matrix representing the metallurgical processing solutions was used to prepare Youden pairs to satisfy the requirements of Committee D19 on Water. Results of the standardization program are presented. INTRODUCTION Analysis of process solutions for gold concentration requires accurate and sensitive analytical methods in order to manage process control and metallurgical accounting. Flame atomic absorption spectrophotometry (FAAS) has been the work horse of the assay lab for this duty for decades. In 1994 the FAAS standard method was approved by the American Society for Testing and Materials (ASTM) (1). Six process solutions were collected and preserved by measuring the pH and adjusting to greater than pH 10, if necessary. Duplicate solutions were provided to eight laboratories in random order for analysis by FAAS covering the gold concentration range of 0.19 µg/mL (0.006 toz/t.) to 10.7 µg/mL (0.312 toz/t). A high precision method was used, which involved bracketing the sample with the higher and lower standards nearest to its concentration repeating readings three times and averaging the results. The optimum precision for the FAAS gold method was found to be at the 1.00 µg/mL (0.029 toz/t) and lower scope limit 0.3 µg/mL (0.009 toz/t) gold concentration. Since tailings solutions typically have concentrations below the lower scope limit, use of ICPMS was developed at Newmont USA Limited (Newmont) to assay the lower range solutions."

Jan 1, 2016

By J. Iannicelli

Kaolin, normally an inert filler when compounded with polymers, is converted into a strongly reinforcing pigment by prereaction with certain functional silanes. Modification of kaolin with amino and mercapto silanes allows it to form crosslinks and confers significant improvements in modulus, abrasion resistance, compression set and other physical properties of a broad range of polymers.

Jan 1, 1990

By W. Nazarewicz

The introduction of continuous papermaking in the early 1800's was the beginning of the industry as we know it today. Since that time, the majority of the paper produced has employed an acid process. However, in the mid 1960?s, European producers began a transition to an alkaline papermaking process. Early European mill conversions to alkaline papermaking begun in the 601s, accelerated during the 1970's influenced by the dramatically higher cost for OPEC energy as well as the high cost of fiber and imported filler clay.

Jan 1, 1986

By H. R. Thompson

The Grant Town Power Plant is a nominal 80 MW (net) Waste Coal-Fired Electric Generating Plant which is located in northern West Virginia, approximately 15 miles southwest of Morgantown. The Steam Generator consists of two (2) Pyro-Power Circulating Fluidized-Bed Boilers (CFB), each rated at 400 000 lbs/hour @ 1,350 psig. Main Steam. The Turbine Generator is a single GEC Ahlstrom unit rated at 95 MW gross and 80 MW net. The Plant began commercial generation during April, 1993. The facility is owned by American Bituminous Power Partners, L.P. (AmBit), and operated by Mission Operations and Maintenance, Inc.

Jan 1, 1996

By P. Legast

Serpentinite minerals are available in large quantities from asbestos mining activity. The granular or fibrous serpentite, at temperatures greater than 700°C, will recrystalize into olivine, forsterite and enstatite. These minerals have been used and studied for decades and are environmentally safe. The thermal process changes the composition and properties of the original mineral. Therefore, the substitution of the original mineral cannot simply be made and the applications for these new synthetic minerals need to be redeveloped. The two original mineral forms allow a wide range of new synthetic raw materials which can be adjusted to specific applications or custom needs.

Jan 1, 1993

By R. L. McNearny

A comparison study was conducted between an actual physical model and a numerical model based on the physical model of the block cave mining method. Results from the numerical analyses closely simulated the blocky behavior of the physical models, including bridging and interlocking of the simulated orebody during draw. The draw-down patterns and the rate of draw developed during numerical modeling also closely simulated the physical models. An unexpected result from the numerical modeling was the development of a zone of downward deflection which preceded the development of the zone of material movement.

Jan 1, 1997

By Karl C. Dean

To assist in the reduction of environmental degradation resulting from milling operations, the Bureau of Mines has developed, and successfully demonstrated, chemical, vegetative, and combined chemical-vegetative procedures for stabilizing milling wastes under varying environmental conditions. Costs of achieving reclamation using these stabilization procedures are compared with those of other physical and vegetative approaches. The Bureau's chemical-vegetative procedure for establishing vegetation directly on fine-sized wastes compares favorably with other stabilization processes that have been used.

Jan 1, 1972

Mining is big business in Ontario. The province is Canada?s leading mining region. It consistently ranks among the top 10 jurisdictions worldwide for exploration spending, reaching about C$1 billion in 2011. More than 26 percent of all exploration and appraisal dollars spent in Canada are invested in Ontario. Minerals produced include nickel, copper, platinum group elements (PGE), cobalt, zinc, diamonds, gold and silver. It was reported that there are more than 600 mining exploration projects in the province. And, recent discoveries of chromite in northern Ontario?s Ring of Fire will add to the province?s mineral production in the coming years.

Jan 1, 2013

By T. M. Biddle

If an accident occurs at a mine, the mining company, its parent and affiliates, and its supervisory employees may face substantial -- and sometimes unexpected -- liabilities and costs. This presentation surveys the likely sources for post-accident exposure, including wrongful death and personal injury claims, mine closure/operational disruptions, and government civil and criminal actions against the company and its employees.

Jan 1, 1986

By Jerry G. Rose

This paper addresses a process by which both the disposal and utilization of preparation plant coal refuse can be simultaneously accomplished with an attendant benefit of significantly increasing the percentage of extractable coal. A laboratory study is described in which coal refuse was successfully utilized as an aggregate in low cost concrete (coal-crete) mixes under simulated mine environments. Coal-crete specimens with compressive strengths of 14,000 kPa (2,000 psi) were consistently produced. A construction sequence and mining plans are offered for placing the low-cost coal-crete pillars in accessible areas in room-and-pillar mines so that a Substantial portion of the remaining coal pillars could be extracted. The method could be applicable in areas where mining procedures do not permit pillar extraction because of possible surface subsidence, roof problems, or other conditions. Possible structural difficulties with the coal-crete pillar support system are discussed. Using a discounted cash flow analysis, the economic feasibility of mining with the coal-crete pillar system is investigated. The cost of the coal-crete pillar system is compared to the cost of a mining system which would have less coal recovery. The analysis indicates that although at higher coal selling prices the coal-crete mining system may yield an acceptable rate of return, the alternative of leaving the coal pillars is more attractive at the present time.

Jan 1, 1977

By Sheldon P. Wimpfen

Back in 1970 Congress passed the National Mining and Minerals policy Act, which had as one of its basic tenets to rely on a strong and stable private minerals industry for the development and production of our mineral resources. Since then, a substantial amount of legislation has been introduced that impacts on the minerals industry. Although most of the bills proposed are not passed into law, each bill affecting minerals and mining is given careful review by the Bureau of Mines. Comment is forwarded with the object of being helpful to legislators by providing our assessment of the probable impact of each bill proposed along with suggestions to improve them. Actually few bills introduced become law. For example, in the 93rd Congress 4,260 bills were introduced in the Senate and 17,690 in the House. In the final accounting there were passed 123 private laws and 649 public, 3 percent of the bills introduced. There would be little merit here in attempting to analyze each mineral-related bill that was proposed. Many are similar and aim at making a certain aspect of our minerals activity fit needs. So, to simplify the task the many bills have been grouped by subjects. Slide 1 shows the principal topics and the number of related bills introduced. Putting it altogether, there are 26 principal subjects and almost 200 bills. And these numbers are probably off somewhat, as this accounting was made early in December.

Jan 1, 1976

By Peter Hall

The need for large volume covered storage has increased drastically in the last ten years. Increased world demand for such products as thermal coal, potash, metallic concentrates, etc., availability of land for large open storage and environmental issues have brought about this need. This paper discusses briefly demand, environment, types of covered storage and the Alternative Storage System "Eurosilo", a proven system for storage of dry bulk mateials in units up to 100,000 m3.

Jan 1, 1982

By Steve Kral

"Liebherr, as most anyone involved with the global mining industry knows, is one of the world’s largest makers of mining and construction heavy equipment. The familyowned company has been around since the 1940s and, according to Stefan Heissler, by the end of next year, will employ about 44,500 people worldwide. Heissler is a member of the board of directors of Liebherr International AG.It all started for the Switzerland-based company when Hans Liebherr first recognized a need for heavy equipment in the construction industry, Heissler said. His first product, introduced in 1949, was the TK10, a mobile crane that, at the time, was a groundbreaking innovation to the heavy construction industry. From there, the company began its growth into a world-leading heavy equipment manufacturer that always relied on innovation.In October, Liebherr gathered a group of mining and construction magazine editors in Leoben, Austria to take a look at the company’s latest addition to the global mining and construction markets. On the mining side, Liebherr provided a demonstration of its T-236 100-t (110-st) haul truck and the PR- 766 50-st (55-st) crawler tractor. The one-day demonstration took place at the Erzberg iron mine near Leoben, where both machines are being proven.The Erzberg Mine, operated by VA Ersberg, has been in operation for about 1,300 years and is said to be Europe’s largest surface mine. It employs about 230 people and mines about 12 Mt/a (13,200 million stpy) of ore, producing about 3 Mt/a (3.3 million stpy) of fine-grained iron ore.T-236 rigid-frame truckThe new T-236 rigid-frame dump truck, with a diesel electric drive system, is Liebherr’s entry into the 100-t (110-st) class and is the first in this class with a four-corner, oilimmersed braking system. The haul truck was first introduced during the 2016 MinExpo in Las Vegas, NV. The unit has since successfully completed its testing phase and is currently in its first field operation trials at the Erzberg iron mine in Austria."

Jan 12, 2017

By V. de Macedo Torres

There are technical and commercial limitations on using high fluorine copper concentrates in industrial copper smelters. The presence of more than 1000 ppm of fluorine in copper concentrates affects the sulfuric acid units generally integrated to copper smelters, and penalties are normally applied to high fluorine concentrate prices. Several process alternatives to this issue were studied at CVRD Technology Center (SUTEC): modifications on conventional sulfuric acid plants to use high fluorine concentrates, removal of fluorine containing minerals in flotation using depressants, selective leaching of fluorine minerals and sulfuric leach of copper concentrates. Finally, a hydrometallurgical process of removing fluorine was developed by SUTEC.

Jan 1, 1997