Search Documents

By Robert W. Miller

There are many problems faced by ventilation engineers in deep underground mining operations, not the least of which is controlling miner exposure to radon gas and its daughter products. Radon gas is commonly found in uranium mining operations, but may also be present in other deep metal mines. For example, tin mines in England, iron ore mines in Sweden, gold mines in South Africa, and molybdenum mines in the U. S. have potential radon exposures. This is because uranium and accompanying radium ore are ubiquitous to the earth's crust albeit at low levels. The fact that the activity represented by one WL can be caused by a relatively low concentration of radon gas increases the difficulty of control. Since the source of the radon gas is usually widespread throughout a mine, local exhaust ventilation is not a viable control schema. The technique used to control exposure is then dilution ventilation and, in fact, huge amounts of air must be moved in order to reduce potential exposures to an acceptable level. An interesting comparison can be made of ventilation rates in different types of mines. It is estimated in modern coal mines, which are generally acknowledged to have high rates of ventilation, that about eleven tons of air are moved for each ton of ore mined. A typical operating uranium mine may have ventilation flows of 14-15 tons per ton of ore mined. This provides an idea of the scope and importance of ventilation in modern mining operations where radon is a hazard. Further pressure is put on ventilation engineers by the steady downward trend in exposure limits set by national and international standard setting agencies. Much of this tendency toward lowered standards is based upon longitudinal mortality studies of miner populations. Another important factor is the limited number of experienced miners available in the labor pool. For optimum production, it is important to have as many experienced miners underground in each shift as possible. However, the average daily exposure in a U. S. mine must be less than .3 WL to permit the miner to work underground for a full year. The ventilation system then must provide enough uncontaminated air to maintain the WL below the .3 TTL level to maximize production efficiency and minimize personnel turnover and the problems associated with it. Ultimately, the goal of the ventilation engineer and health physicist is to protect the working miner from harmful exposures based upon currently acceptable standards. U. S. Federal regulations require that in uranium mines all active work sites must be monitored every two weeks if they measure above .1 WL. Areas that have .3 WL ratios or higher must be monitored on a weekly basis until five consecutive weekly samples show the level has dropped below .3 WL. Also, exposure records must be kept for all individuals exposed to levels exceeding .3 WL. These requirements provide a strong economic incentive to have a ventilation system that minimizes exposure of any personnel. A good ventilation system requires careful planning, operation and backup in order to fulfill its mission of providing adequate clean air. Its proper operation also requires coordination with production personnel so it can be adapted as new areas in the mine open up and old areas are sealed off. The ultimate indicator of ventilation efficiency to control radon daughter exposure is, of course, monitoring working levels. Historically, this has been done using the Kusnetz, Tsivoglou, and Rolle's methods, among others. These methods all require cumbersome equipment and tedious calculations to obtain the measurements that results in WL. More important, however, they require a significant time lag between sampling and counting, typically 40-90 minutes. This time lag is, in fact, what can cause significant economic losses due to unnecessary downtime as well as high WL exposures. In a typical mining situation, a sampling technician using the Kusnetz method takes a sample, moves to the next location and takes another sample and so on. Forty to ninety minutes after the first sample, the technician will stop, run the activity count on the filter and calculate the WL. The technician may be one-half mile away or several levels removed from where the first sample was taken when it is counted. If the WL ratio is high the technician must then backtrack to the sample position. There are then two options. If the sample area is a working stage, it can be shut down or a second sample can be taken. If the first alternative is chosen; i.e., shutdown and correction of the ventilation, then another sample must be taken, followed by a forty minute wait for results. If the ventilation adjustment didn't correct the problem, then the whole process must be repeated with a minimum of forty-five minutes per sample cycle when using the Kusnetz method. It has been estimated from operating uranium mines that the cost per hour for downtime on a production slope is about $1,50O/hour. The time lag between sampling and resultant data can be very costly. If the second alternative is chosen to verify the first reading, the miners may be unnecessarily exposed to high levels while waiting for the result. Clearly, such a sampling system can be markedly improved by eliminating the excessive time lag between sampling and analysis.

Jan 1, 1981

By C. S. Thompson, P. A. Ciullo

Pyrophyllite is a naturally occurring hydrous aluminum silicate with the molecular formula SiO,,AI,,(OH), or, as more commonly expressed, the oxide formula A120,~4Si02~H20. Pyrophyllite is rarely found in deposits as the pure mineral and is often intimately associated with quartz, sericite, kaolinite, and diaspore. These associated minerals, to a large degree, help determine the most appropriate commercial application for a given pyrophyllite ore. Structural similarities plus the generally soft platy nature of pyrophyllite has in the past caused it to be included with talc in applications and production data. The Minerals Yearbook, published annually by the US Bureau of Mines (USBM), still reports on talc and pyrophyllite together, although admitting that they do not share the same uses. Pyrophyllite has also at times been considered a clay mineral because of its structure and chemistry. The refractory properties of pyrophyllite have been known for nearly 200 years, but it has only been in the past 60 to 70 years that a variety of applications have been developed to exploit the unique characteristics of this mineral. Worldwide, pyrophyllite is a component of refractories, whiteware, foundry mold dressings, pesticides, paint, plastics, rubber, cement, fiberglass, and soap. Historical Overview The most salient refractory features of pyrophyllite are its low coefficient of thermal expansion, high thermal conductivity, low moisture expansion, and good resistance to corrosion by molten metals and basic slags. One of the first recorded uses of this mineral was as firebrick in Japan in the early 1800s. This followed its discovery in 1797 on Mount Omotoyama at the site of the present Mitsuishi mine. In addition to firebrick, sawn blocks of ore were used for carvings and in the manufacture of slate pencils and signature seals. The Mitsuishi mine is still one of Japan's largest. By the mid-1800s, refractories were being made in Japan from roseki (a pyrophyllite-bearing ore) for the construction of metal melting furnaces. The mineral did not get its name until 1829 when R. Herman, testing a sample of supposed talc from the gold-quartz veins at the Berezovo deposit in the Urals, showed that it was actually an aluminum silicate and designated it pyrophyllite. This name was derived from the Greek pur for fue and phullon for leaf, in allusion to the effect of heat in causing separation of the laminae in foliated varieties (Mellor, 1927). The exact date of the discovery of pyrophyllite in the United States is uncertain, but it is believed that the talc and soapstone deposits noted in an 1827 report on the geology of the slate belt of North Carolina were actually pyrophyllite occurrences (Olmstead, 1827). Pyrophyllite was first used in North Carolina on a local basis in the early 1800s. Blocks were sawn and cut for use as stove linings, mantels, chimneys, fireplaces, and gravestones. This was the material of choice because it did not shrink when heated, but cut easily and hardened as it weathered. Pyrophyllite crayons were sold commercially by local gold miners for steel marking and as tailor's chalk from about 1800 until 1922. It was during this period that pyrophyllite was discovered near the town of Hemp (later renamed Robbins), NC. The large quantity of scrap resulting from the sawing of crayons at this deposit prompted the construction in 1921 of a grinding plant. The ore scrap was ground to fine granules and sold to asphalt producers to prevent shingles from sticking together. By the mid-1930s, milled pyrophyllite from North Carolina was also being successfully utilized by the ceramics industry in whiteware for its low cost and ability to shorten firing time. Also during the 1930s, pyrophyllite was first used in kilncar furniture in the United States. Canada was another early entrant in the pyrophyllite business. Mining at the Foxtrap deposit on the Avalon Peninsula of Newfoundland began in 1904, with ore shipped to the United States. Production from this deposit was mostly sporadic in the ensuing years until 1956 when mining began for shipment and captive use in US tile manufacture. This production has remained continuous and still essentially captive to the present. The Foxtrap deposit is currently the sole commercial source of pyrophyllite in Canada.

Jan 1, 1994

By D. W. H. Su

"This paper presents the results of a comprehensive study conducted by CONSOL Energy, Marcellus Shale Coalition, and Pennsylvania Coal Association to evaluate the effects of longwall-induced subsurface deformations on the mechanical integrity of shale gas wells drilled over a longwall abutment pillar. The primary objective is to demonstrate that a properly constructed gas well in a standard longwall abutment pillar can maintain mechanical integrity during and after mining operations. A study site was selected over a southwestern Pennsylvania coal mine, which extracts 1,500-ft-wide longwall faces under about 600 feet of cover. Four test wells and four monitoring wells were drilled and installed over a 125-ft by 275-ft centers abutment pillar. In addition to the test wells and monitoring wells, surface subsidence measurements and underground coal pillar pressure measurements were conducted as the 1,500-ft-wide longwall panels on the south and north sides of the abutment pillar were mined by. To evaluate the resulting coal protection casing profile and lateral displacement, three separate 60-arm caliper surveys were conducted. Prior to the longwall panels being mined by, a number of 3D finite element simulations were conducted to estimate subsidence at the surface, coal pillar pressure increases, the resulting coal protection casing profile and displacement, and the vertical and horizontal displacements in the four monitoring wells. Comparisons of the pre-mining 3D finite element simulation results and the surface/subsurface/underground instrumentation results show that the measured test well and IPI casing deformations and profiles are in reasonable agreement with those predicted by the 3D finite element models, and that the measured surface subsidence and pillar pressure are in excellent agreement with those predicted by the 3D models, which serves to validate the 3D finite element models. Parametric studies employing the validated 3D finite element models demonstrate that larger coal protection casing thickness is expected to have little effect on the lateral deformation, although it may reduce the magnitude of casing plastic deformation, and under deeper cover (~1,100 feet), lateral casing deformation is expected to be smaller, although larger plastic casing deformation may be present near the seam level. Also, evaluation of various casing and cementing designs using the validated 3D models clearly indicates that, when all casings are grouted to the surface except the intermediate and production casings, the intermediate and production casings show little deformation and no plastic strain. This research represents a very important step and initiative to utilize the knowledge and science obtained from mining research to improve miner and public safety as well as the safety and health of the oil and gas industries"

Jan 1, 2017

By G. A. Campbell

Mining companies have been very interested in the presence of a number of small but high-grade ore bodies of base metals in northern Wisconsin and the west/central section of the Upper Peninsula (UP) of Michigan. The region is rural with outdoor recreation/tourism and lumbering being the key industries. The economy of the region is based on the use of its natural resources, and mining is not a new activity to the region, especially the UP. The western UP was historically a key mining district for copper and iron, and today the central UP has a significant iron-mining district. However, all efforts to develop the base metal ore bodies have been met with a storm of controversy involving the local community, regional activists, Native Americans, and the state government, and only one mine has gone into operation. There is concern by some stakeholders about the sustainability of mining in communities that depend on the environment for tourism, recreation, and other commercial activities. There have been four attempts to get the necessary approvals to mine in this region: the successful Flambeau Mine effort (Wisconsin), the failed Crandon project (Wisconsin) and Lynne project (Wisconsin) efforts, and the continuing effort to get the Eagle Project (UP of Michigan) approved. The cases are presented to illustrate the project situation, the history of the permitting effort, and the opposing parties and their concerns. The case of the Eagle Project is looked at in detail by using the method of discourse communities and discourse analysis. Results of the analysis provide insight into the communication efforts to address community concerns about sustainability and what more can be done to improve this dialogue.

Jan 1, 2008

By T. J. Crebs

The latest estimates compiled by the Society of Exploration Geophysicists again indicate a moderate increase in mining geophysical activity in 1980 over the 1979 level. While North American activity remained at above the 1979 level, a considerable increase in mining geophysics was reported in South America, Australia, and the Far East. The total worldwide expenditures for mining geophysics were reported to be $53.7 million in 1980, compared to $44.4 million in 1979, and $31.6 million in 1978. During 1980, approximately 2% of all dollars spent on geophysics were attributed to mining geophysical activities; this percentage has remained relatively constant in recent years. Airborne surveys accounted for 51% of the total worldwide mining geophysical expenditure, 43% was spent for land surveys, and 6% for borehole surveys. Within the US, the breakdown of expenditures for land surveys was 60% for elec¬trical methods, 23% for gravity and magnetic methods, and 17% for seismic techniques. Electrical techniques remain the primary exploration tool for US mining geophysicists. Electrical Methods With inductive or electromagnetic (EM) techniques, significant developments were achieved in both frequency-domain and time-domain systems. Work continued on increasing the signal level on most time-domain (TEM) methods, to increase the exploration depth. The Crone group increased the power of its Pulse ElectroMagnetic system (PEM) to a 20-amp transmitter-loop capability. The GEOEX group is modifying the SIROTEM II system to obtain larger transmitter amperage from a portable motor generator. Geonics developed a new digital recording system (data logger) for its EM-37 system. This development should increase the productivity of EM-37 crews. A new ground, frequency-domain EM system was developed by the Scintrex group. This novel Genie system does not require a wire link between the receiver and transmitter. Because an amplitude-ratio is measured, the Genie data are reported to be relatively insensitive to coil orientation and distance errors. This new technique does not need extensive line-cutting or accurate station-chaining and would appear to be a good reconnaissance instrument. Scintrex also began marketing the new IPR-11 induced polarization spectral receiver. This receiver is microprocessor controlled, and can output to a cassette tape and record 10 windows of secondary voltage decay simultaneously from up to six receiver dipoles. The Phoenix group's new 100 kW induced polarization/resistivity (IP/R) transmitter began tests using their IPV-3 multifrequency, multichannel receiver. While this unit was primarily developed for "oilfield" IP exploration research, it has obvious application to "deep" mineral exploration. The Phoenix group also developed a new remote-reference, real-time magneto-telluric (MT) device in 1981. This five-component MT sys¬tem has a frequency range from 0.0005-384 Hz. Helicopter-borne electromagnetic (HEM) developments also continued in 1981. The mining in¬dustry increased its use of the new Geonics EM-33-3 multifrequency, multicoil instrument. In 1981, the Dighem group developed software for estimating magnetite as a mapping parameter from its HEM system. Dighem's work is said to complement airborne magnetic intensity surveys, since the HEM estimate is independent of remanent magnetism and magnetic latitude effects. Gravity and Magnetic Methods Probably one of the most innovative techniques in geophysics in 1981 was the use of airborne gravity surveys for both mining and petroleum exploration. The Carson group is using a modified, shipborne LaCoste-Romberg platform in helicopters. Data accuracies to 0.5 milligal have been achieved by flying gridded surveys. Although this airborne method is expensive-up to $186/ km ($300/line-mile)-the geophysical community has been excited by initial results. On the ground, the portable proton-precession magnetometers are becoming sophisticated. Both GeoMetrics and EDA recently introduced field magnetometers having data storage and processing capabilities. This development should greatly increase the productivity of ground-magnetic surveys. Seismic Methods Development of high-resolution seismic techniques continued in 1981. These techniques have primarily been directed toward coal studies for fault detection. OYO Instruments introduced their McSEIS-1500 seismic data acquisition system in 1981. This device contains a 24-channel recording capability, with digital output to 256-kbyte floppy disks. The high-speed data transfer using the disk media is considered a desirable feature. Borehole Methods The general decrease in uranium exploration, where borehole logging is extensively used, probbly led to the overall decline of geophysical logging activity in the minerals industry. However, a number of new sondes and logging systems were introduced in 1981: • Mount Sopris recently introduced their Series III logging system. This microprocessor-controlled unit records up to four channels of data on nine-track or cassette magnetic tape. The logging package is relatively light-weight, so helicopter transport to mountainous or roadless exploration sites is possible. (Both the Edcon and Woodware-Clyde consulting groups offer "slinging" capabilities for their Mount Sopris units.) Mount Sopris is continuing work on their 500-mm-diam (2¬in-diam) spectral gamma-ray sonde. This tool is expected to be available soon. • Owl Technical "slim-downed" its successful digital deviation probe to 380-mm (1.5-in) outside diameter. This new sonde will also measure inclinations up to 80° from the vertical, as compared with its older instrument that could measure inclinations to 30°. • A magnetic susceptibility sonde was introduced in the US by the OYO Instruments group. This Kappalog sonde contains two aircored coils for measurements slightly affected by thermal changes within the borehole. The increased activity in massive-sulfide exploration and the need to "look" deeper no

Jan 5, 1982

By Charles R. Nelson

INTRODUCTION The support of openings in weak sandstones can be achieved by spraying on a liquid grout which will soak in and harden to form a shell. In the St. Peter sandstone of the Minneapolis-St. Paul area of Minnesota compressive strength is increased from about 0.7 MPa (100 psi) to over 7 MPa (1000 psi) to depths of 152 mm (6 in.). A shell of this strength and thickness can pro¬vide support much as shotcrete does but at lower cost. If the spray-grouted shell is inadequate for the support needed, it provides a good base for shotcrete application, which is often difficult in weak or friable sand¬stones because the fresh shotcrete peels off along with a thin layer of sandstone. The spray-grouted technique was initially developed at the Civil and Mineral Engineering Dept. of the University of Minnesota using funds provided by RANN Div. of the National Science Foundation. It was used as temporary support in a 3-m (10-ft) wide, 3700-m (12,000-ft) long storm water drain tunnel by the Minneapolis Sewer Construction Dept. Much of the field development at this construction project was carried out with the cooperation of the personnel of the city of Minneapolis. It also was used for temporary support in a 3.3-m (11-ft) wide, 1800-m (6000-ft) long storm water tunnel built in 1978-1980 for the Minnesota Dept. of Transportation in Minneapolis. In 1975, 2000 m (6500 ft) of 1.5-m (5-ft) wide utility tunnels were spray-grouted for final lining. A 50-m (150-ft) long, 1.2-m (4-ft) wide test tunnel built at the university in 1974 was sprayed for half its length and is being observed for long-term behavior which to date (1981) is good. GROUT MATERIALS The requirements for the liquid grout are more severe than those for injection grouting. Besides being able to penetrate the rock and develop sufficient strength, it must have the following properties: (1) be nontoxic, noncombustible, and have a low odor for spraying under¬ground; (2) have controllable viscosity and setting time for adjusting to the permeability of the sandstone and the required depth of penetration; and (3) must "wet" the sandstone and develop capillary "draw" to penetrate to the required depth. A sodium silicate-based grout with the proper setting agent meets these requirements in the local St. Peter sandstone which has a uniform grain size dis¬tribution curve with D,,, = 0.1 mm, permeability of about 10 to 20 darcys, a porosity of about 25%, and less than 5% of silt size or smaller. It is 97 to 99% pure SiO2. The grout mix consists of Philadelphia Quartz Co. Type N sodium silicate and Celtite 55 Terraset Spray Grade (SG) distributed by Celtite Inc., Cleveland, OH. A volume mix ratio of 100:9:125 for sodium silicate to setting agent to water produces a grout with two to four centipoise viscosity, and initial set at 20°C of 20 min. Setting time is temperature dependent, being longer at lower temperatures, but can be adjusted by varying the setting agent concentration a few percentage points. APPLICATION The application is simple. Spray the grout on the surface until the desired penetration is achieved. Penetration rates of about 5 mm (0.2 in.) per min. are realized in the St. Peter sandstone for up to 152 mm (6 in.) of penetration (30 min. of spraying). The set time must be longer than the spraying time. The spray nozzle should be moved back and forth at a rate that minimizes runoff due to surface buildup. Both a single large hand-propelled nozzle and multiple small machine propelled nozzles have been used successfully. The pumping and mixing equipment used consisted of: (1) a hand-held, hand-pumped, 11-L (3-gal) gar¬den sprayer for test patches (mix by shaking); (2) 76-L (20 gal) batch mixing in barrels with small electric pumps for spraying and mixing; (3) two component pumps consisting of Hypro Model 5300 piston pumps (Hypro Pump Co., St. Paul, MN) on a common shaft driven by an electric motor. The sodium silicate is premixed with a portion of the water and the setting agent is mixed with the rest of the water. The two components are combined and mixed just before the nozzle; and (4) a proportioner metering the setting agent just before the nozzle with the water and sodium silicate premixed and pumped from the surface. The proportioner permits the bulk of the grout to be pumped through a single pipe or hose with only the setting agent stored underground. This is efficient and low in cost. COST The grout mix costs about $0.20/L ($0.75 per gal) in 1978 dollars. Filling all the voids 100 mm (4 in.) deep (25% initial porosity) would have a materials cost of about $5.40/m2 ($0.50 per sq ft). The labor cost of application is usually less than the material cost for normal tunnel jobs. A pump and proportioner cost less than $1000. Sodium silicate storage tanks and pip¬ing costs would depend on the particular site conditions. REFERENCES AND BIBLIOGRAPHY Nelson, C. R., 1977, "Spray Grouting for Tunnel Support and Lining," Underground Space, Vol. 1, No. 3, pp. 241¬ 245. Yardley, D. H., Nelson, C. R., Stocker, T. H., 1974, "So¬dium Silicate Spray Impregnation of Tunnels in the St. Peter Sandstone," Research Report, University of Min¬nesota, 118 pp.

Jan 1, 1982

By D. T. McMurray

INTRODUCTION Shabanie mine, situated some 180 km east of Bula¬wayo, has been a producer of chrysotile asbestos for more than 50 years. The ore bodies occur in serpentinized dunite, which overlies talc-carbonate schist. A zone of relatively competent rock of varying thickness occurs between the schist and the ore bodies, which are gen¬erally less competent. The hanging wall of the ore bodies is economic, and the hanging-wall serpentine carries a variable subeconomic amount of fiber. It is important to note that, in general, the ore body competence is less than that of the foot and hanging-wall formations. Historical After surface operations ceased, cut-and-fill stoping was used to win ore from underground; this was success¬ful until the increasingly stoped-out area caused insta¬bility in the stope pillars and back. Consequently, dur¬ing the early 1950s, a gradual change to cave-mining methods was made, the ore being won by hand lashing in drawpoints, situated in the basement of the stope blocks, and passed through orepasses under gravity to the haulage level some 13 m below. About this time, interest was focused on the sub¬level caving method in use in Swedish iron ore mines: it was felt that it might be applied economically to the Shabanie ore bodies. Accordingly, in 1958, an experi¬mental stope block was laid out in which sublevel inter¬vals and extraction tunnel spacing were 9 m. The tun¬nels (ring drilling drives) were oriented on strike-in contrast to the Swedish system, in which crosscuts that retreat from hanging to footwall are used. The advantages of the method were quickly appre¬ciated by the operating personnel and, despite the in¬evitable teething troubles pertaining to the introduction of any new mining method, it was not long before sub¬level caving was providing a high proportion of the mill feed. The disadvantages also became apparent at an early stage, however, and, from that time to the present, continuing modifications have been made to mining lay¬outs in an effort to improve ore recovery. GENERAL DESCRIPTION OF METHOD The mine is served by a vertical hoisting shaft, in which two skips, a man cage and a service cage, provide adequate capacity for production requirements. The rock hoist is a Ward Leonard control hoist, in which two electric motors drive a common gearbox. The man winder is driven by an a-c motor. Several auxiliary shafts provide secondary egress and intake and return ventilation. Main haulage levels are above (Fig. I a and b). Blasthole fan patterns are drilled by drifters of 100 mm bore, drilling 41-mm holes; when a sufficient strike length has been drilled, a slot is cut in the upper¬most sublevel and the rings are broken into the slot. Initially, a limited tonnage is drawn, since it is essential to ensure that the hanging wall caves behind the retreat¬ing stope face. Once this has been established, maxi¬mum tonnage can be drawn, as described later in this chapter, under the heading "Draw Control." The broken rock is loaded by 0.14 and 0.20-m3 load¬ers into cocopans (rocker-dumping type of tipping truck), which are hand trammed to orepasses, discharg¬ing on the haulage where 11-t electric trolley locomo¬tives haul 3.95-m3 Granby cars to the main shaft bins. As is evident from Fig. 1, the layout is simple, the block is brought rapidly into production, there is a high degree of selectivity and flexibility, and the result is a low-cost high-productivity mining method. DEVELOPMENT Main haulages are developed at 3.2 x 3.2 m, and once the service winze connections have been completed the development of the sublevels is undertaken. The footwall drives are cut first, to obtain access to the block. These ends are of the standard section, 2.4 x 2.8 m, and from them crosscuts at intervals of 70 m are driven through the ore body to the hanging wall. These crosscuts are used to supplement the geo¬logical information previously obtained from diamond core drilling, and they provide additional and more de¬tailed data on fiber percentages and lengths, structural features, and other relevant criteria which are used to build up the geological assessment of the area and to classify it in terms of the geomechanics rock classification (Laubscher and Taylor, 1977). The crosscuts also allow the necessary orepasses to be sited conveniently so that tramming distances from the loading points are not excessive. Development Drilling Once the skeleton development has been completed, the extraction headings are developed at 2.4 x 2.4 m as shown in Fig. 1. Standard development practice is to use crews of a machine operator and his helper, equipped with air-leg mounted jackhammers, to drill rounds of 1.8 m with integral tungsten carbide tipped drill steel. The round drilled is a normal drag round, as shown in Fig. 2, but considerable attention is paid to the drilling of the perimeter holes to use effectively the

Jan 1, 1982

By William H. Wiese

Anecdotal reports of high rates of congenital malformations and spontaneous abortions at the Shiprock Indian Health Service Hospital in San Juan County, New Mexico prompted an interview survey, obtaining data from families of 26 former uranium miners and 30 controls. Results supported the possibility of increased fetal wastage and congenital malformations. However, definitive conclusions were obviated by methodologic limitations in terms of selection of cases and controls and interviewing technique, as well as very low numbers and lack of statistical significance. The Council of Environmental Quality (1980) published a report which singled out San Juan County, nationally, as having an extra-ordinary high rate of congenital anomalies reported from birth certificates in the years 1973-75. San Juan County is in the northwest corner of New Mexico and includes the northeastern edge of the Navajo Indian Reservation. It has been the site of uranium mining and milling and also of coal mining (Clement Associates, 1980). While much attention has been focused on lung cancer and chronic lung disease as health hazards to uranium miners, virtually no attention has been focused upon possible reproductive effects that may result from exposure to radiation. Could these reports indicate such an additional arena of health effect either on miners or on others living in the vicinity of the mines and mills? The biologic and epidemiologic literature does not lend much support for adverse genetic outcome. The UNSCEAR report (UNSCEAR, 1977) summarizes much of the existing data. For example, on the basis of many animal studies and what has been observed in atom bomb survivers in Japan, it has been estimated that mutation rates resulting from low LET radiation to paternal germ cells would be 60 X 10-6 recessive and 20 X 10-6 dominant mutations per gamete per rad. There would be a five-fold increase in the number of recognizable abortions. The doubling dose for genetic disorders in mice is estimated at 100 rads. The assumption has been that low levels of exposure, such as might be received occupationally from uranium mines and mills or environmentally will produce reproductive effects that would defy distinction from background rates. However, the possibility can not be dismissed. In man, spermatogonia are thought to be three-fold more sensitive than in the mouse. Also, the high LET radiation from alpha particles is as much as 20-fold more effective in inducing changes in meiotic and post meiotic stages of cells, compared with low LET radiation. There is some degree of localization of alpha emitters in testicular tissue after inhalation of radon and radon daughters (Blanchard, R.L. and Moore, J.B., 1971; Pohl, E., 1964). The slopes of doseeffect curves are affected by type radiation and rate of administration. Data on such curves are poorly defined and debated as to whether there may be increased or decreased effect per unit dose at low levels of high LET radiation. Increased rates of aberrations of chromosomes in peripheral lymphocytes cultured from uranium miners have been reported (Brandom, W.F., et al., 1978). At cumulative exposures of 100 working level months (WLM) or less, a range of exposure lower than the limit of current occupational standards, the aberrations were increased more than two-fold. Our interest has led us to pursue the question of reproductive effects along three separate paths of inquiry: studies of the secondary sex ratio, cytogenetic study of human sperm, and studies of rates of congenital anomalies. I will present the thrust of our findings, most of which remain preliminary, comment on their interpretation and limitations, and indicate directions needed for future research. The secondary sex ratio is the ratio of males to females at birth. In the U.S., the ratio averages around 1.05. Ratios in blacks are somewhat lower (1.025) than in whites (1.053). For American Indians, the data are less definite. Values from Oklahoma and California are similar to whites (1.05). Southwestern tribes have, as we shall see, varying levels. The theoretical effects on sex ratio resulting from irradiation of the zygote are based on the principles of sex-linked genetics, including differential effects of lethal dominant and recessive mutations on the sex chromosomes, complicated by possible non-disjunctional events. Observations have done little to clarify, confirm or refute the theories. The sex ratio of progeny of survivers of the atomic bomb showed little change (Schull, W.J., Otake, M., and Neel, J.V., 1981). Observations in children of uranium miners having been inconsistent. Most frequently cited is a study of miners in Czechoslovakia (Müller, C., Razicka, L., and Bakstein, J., 1967). Compared with children born to miners prior to the start of mining, the sex ratios of children born after the start of mining were decreased -statistically significant after correcting for birth order. The ratios in first-born children were, before the start of mining, 1.118, and, after the start of mining, .713. In the interview survey at Shiprock, the sex ratio in families of non-miners was 1.03, and in families of miners it was 0.73 (p < .05). Dr. Alan Goodman at the University of New Mexico has studied trends in the sex ratio in the general population in New Mexico and Arizona with particular reference to counties in the Four Corners area and the Navajo Indian Reservation, areas where uranium mining has been active_ His findings (unpublished) are as follows: (1) Beginning in the early 1950&apos;s, there has been a modest, but persistant and statistically significant decline in the secondary sex ratio for the state of New Mexico compared with the U.S., a decline that roughly parallels the emergence of uranium mining in the Grants mineral belt in northwestern New Mexico. (2) Data available for the 11 years since 1969 show that among the five counties with ratios significantly lower than the state

Jan 1, 1981

By Gordon T. Austin

Garnet is the general name for a family of complex silicate minerals having similar physical properties and crystallizing in the isometric (cubic) system. All garnets have the same general chemical formula but vary greatly in chemical composition. The name garnet is derived from the Latin word granatus, meaning like a grain, which refers to the mode of occurrence wherein crystals resemble grains or seeds embedded in the matrix. GEOLOGY Mineralogy Chemical Properties: The general formula for garnet is A3B2(SiO4)3, whereas A can be calcium, magnesium, ferrous iron, or manganese, and B can be aluminum. ferric iron, or chromium, or rarely titanium. The formulas and names of common garnet species are: [ ] Almandite and almandite-pyrope solid solution garnets are the best abrasive types, but andradite, grossularite, and pyrope also are used. All species of garnet have been used as gemstones. The structure of garnet consists essentially of isolated SiO, tetrahedra connected by oxygen-cation-oxygen bonds through the distinct A and B group cation sites. Within this structure magnesium, ferrous iron, and manganese easily interchange and substitute for each other in the A cation position, and calcium does so less readily. Additionally, aluminum, femc iron, and chromium substitute for each other to a limited extent in the B cation position. This ability to substitute or exchange ions without changing the crystal structure is called isomorphism, and garnet is one of the finest examples of a isomorphous series. Because of this isomorphism there is complete solid solution between certain garnet species but not between others. Fig. 1 illustrates these solid solution relationships. Some rare species of garnet are known that illustrate the wide range of cation substitution that the garnet crystal structure can accommodate. They include: [ ] These rare species are not of interest for industrial applications, but can be of interest to mineralogists and the gem industry. Physical Properties: Garnet displays the greatest variety of color of any industrial mineral. Garnets have been found in all colors except blue. For example, grossularite can be colorless, white, gray, yellow, yellowish green, various shades of green, brown, pink, reddish, or black. Andradite garnet can be yellow- green, green, greenish brown, orangy yellow, brown, grayish black or black. Pyrope is commonly purplish red, pinkish red, orangy red, crimson, or dark red; and almandite is deep red, brownish red, brownish black or violet-red. Spessartite garnet can be red, reddish orange, orange, yellow-brown, reddish brown, or blackish brown. A few garnets exhibit a color-change phenomenon. They are one color when viewed in natural light and another color when viewed in incandescent light. Because of the great variation in color of garnet within each species and similarities in color between garnets of different species it is recommended that garnet identification not be based on color alone. The Mohs hardness of garnet varies from 6.5 to 9.0. Grossularite and uvarovite have a hardness of 6.5 to 7.5; andradite is 6.5 to 7.0; and pyrope, almandite, and spessartite are 7.0 to 7.5 in hardness. There are reports of almandite having a hardness of between 8.0 and 9.0. As with hardness, the specific gravity of garnet varies considerably. The specific gravity may be as low as 3.2 or as high as 4.3 depending on chemical composition. Garnet crystallizes in the isometric system with rhombic dodecahedra and trapezohedra the most common forms. Crystals also form in combinations of dodecahedra and trapezohedra or either of these in combination with hexoctahedra. Crystals can have cubic or octahedral faces, but these are rare. Under favorable conditions of formation garnet will crystalize in nearly perfect forms that rival study models. Garnet also forms as irregular blebs, grains, knots, or masses, with or without distinguishable crystal faces, and as coarse- or fine-grained granular masses that appear to be totally lacking in crystal form. The fracture of garnet also shows great variation. In some garnets, particularly those that are well crystallized and glassy in appearance, the fracture is subconchoidal to conchoidal. Other, more poorly crystallized garnets exhibit a fracture that can only be described as uneven. Garnet occasionally has an indistinct dodecahedral cleavage. Certain species of garnet from specific locations have a pronounced laminated structure consisting of planes of weakness along which parting takes place. This parting may resemble cleavage, but since it is mechanical and not related to crystal structure it is not true cleavage. The optical properties of garnet are sensitive to even small changes in chemical composition or strain in the crystal structure. For this reason each species does not have a single index of re- fraction (IR) but has a range of 1Rs. Uvarovite in its pure form should have an IR of 1.870, but in nature samples vary from 1.74

Jan 1, 1994

By Dave Southworth

After Abe Lee discovered gold (in April 1860) near the site of present-day Leadville, Colorado, he and is group staked nearly all of California Gulch with "speculative claims." They did so in an effort to grab any property that might be potentially profitable. But the plan did not work. New prospectors demanded a miners&apos; meeting, from which arose the official "Bylaws of California Mining District, California Gulch, Arkansas River." These bylaws, adopted on May 12, 1860, established provisions as to the number, size and type of claims that could be filed. Fair laws invited more newcomers. By mid-summer, 5,000 people with tents and wagons were scattered from one end of the gulch to the other.Among the earliest arrivals to the region that spring were Horace Austin Warner Tabor and his wife, Augusta. H.A.W. Tabor, who was to become a pillar in the development of Leadville, arrived at California Gulch during a food shortage. He sacrificed his oxen so that hungry miners could eat. By doing so, he immediately became the friend of many. Augusta established a little store where she sold her baked goods and provided meals. Like most of the men, Horace prospected the surrounding hills. He only did so, however, for a short time. California Gulch yielded more than $5 million in gold during the next five years. By 1866, however, the placer gold was gone and most of the miners had packed up and left. Charles J. Mullen and Cooper Smith, who were grubstaked by a Philadelphian named J. Marshall Paul, found a new, rich lode at the Printer Boy Mine in 1868. It was the first underground gold mine in the Leadville area and marked the transition from surface mining to underground hard rock mining. Its discovery created a new but modest flurry of activity. Heavy black sand covered the region and made gold mining difficult. In 1875 William Stevens and Alvinus Wood decided to have the sand assayed. They discovered that it contained 15 ounces per ton of silver and was rich in carbonate. Stevens and Wood kept their find a secret for nearly two years. When the word spread in late 1877, the silver boom was on. In 1878 prospectors, merchants and others trickled into town from all directions. Dr. David H. Dougan closed his office. in Alma, crossed Mosquito Pass and set up shop in Leadville. Nobody seemed to need a doctor, however, and Dougan sat in his office for 28 days without a customer. On the 29th day he received word that there had been a mining accident and he was needed immediately. -That was the begin¬ning of his illustrious career in Leadville. Dougan was a successful physician, became mayor in 1881 and was later president of the Carbonate National Bank. Leadville was a simple community of log structures in 1878. By June of the following year, however, it had blossomed considerably. According to Cass Carpenter, as of May 1,1879, Leadville had "...19 hotels, 41 lodging houses, 82 drinking saloons, 38 restaurants, 13 wholesale liquor houses, 10 lumber yards, 7 smelting and reduction works, 2 sampling works for testing ores, 12 blacksmith shops, 6 livery stables, 6 jewelry stores, 3 undertakers and 21 gambling houses where all sorts of games are played as openly as the Sunday School sermon is conducted." Additionally, there were 36 brothels. When George E. King and other architects arrived, Leadville took on an air of elegance and sophistication. In sharp contrast to some of the Victorian-style, gingerbread-laced homes in Leadville, its suburbs were comprised of many tenement shacks and plain cabins mixed with a few commercial buildings, many mines and smelters. Mines sprinkled the area east of Leadville like pepper from a pepper shaker. Wherever there was a cluster of mines, a camp usually sprang up. Most were very close together. South of Leadville the giant Arkansas Valley lead smelter sprawled out between Stringtown and Bucktown in an area known as Smelter Valley. Founded in 1879 as the Billing and Eilers Smelter, the Arkansas Valley plant was operated by the American Smelting and Refining Company. Several other smelters operated in the vicin¬ity. In April 1878, Horace Tabor grubstaked prospectors August Rische and George Hook. For $64 worth of supplies and tools, he was guaranteed a one-third interest in their findings. Rische and Hook discovered the Little Pittsburg (often spelled Pittsburgh) Mine and made Tabor an instant millionaire. Tabor once purchased a "salted" mine, the Chrysolite; but instead of considering it a bad deal, he further developed the property and struck rich silver ore. Later, Tabor purchased the Matchless Mine for $117,000, possibly the only investment he made without partners. During its peak years, the Matchless yielded $1 million worth

Jan 1, 1998

By Frank G. Horino, V. E. Hooker

INTRODUCTION The determination and use of mechanical properties of rock in engineering and rock mechanics are rapidly developing. Many of these properties are determined on intact rock specimens; thus, their application and repre¬sentation of rock mass properties may be limited. How¬ever, relative information often provides useful guidance in the solution to mine design and stability problems. Summarized in this chapter are some of the stan¬dardized techniques and procedures currently used to obtain these mechanical properties. Typical applications of the use of these properties are also presented. Stan¬dardized techniques include those advanced by the American Society of Testing and Materials (ASTM), International Society of Rock Mechanics (ISRM), US Bureau of Mines (USBM), Canadian Dept. of Mines and Technical Surveys, South African Institute of Min¬ing and Metallurgy, and other individual investigators. Information on the mechanical properties of rock and the behavior of the rock under a given system of stresses represents a necessary part of the information for rational engineering design for any given mining op¬eration. The mining method, the type and extent of sup¬port, the extraction ratio, the overall dimensions of the mine, and the orientation of the rooms and pillars are all decisions that are influenced by the mechanical prop¬erties of the ore, roof, and floor material under various stress systems and the magnitude and direction of the in situ stresses (Hooker, Bickel, and Aggson, 1972). Initial mechanical property information regarding a structure or mine property is generally obtained by two basic techniques: (1) static and dynamic property tests are conducted on intact and fractured rock specimens of exploratory drill core, and (2) dynamic properties are obtained by borehole logging techniques. When mining access becomes available, and as the mining horizon is expanded, additional information can be ob¬tained to verify preliminary mine design values. This chapter presents some of the standardized tech¬niques and equipment currently used in obtaining me¬chanical property data in the laboratory. The properties considered are: (1) uniaxial compressive strength of intact rock core specimens, (2) uniaxial compressive strength of rock cores containing planes of weakness, (3) triaxial compressive strength of intact rock core specimens, (4) triaxial compressive strength of cores with a plane of weakness, (5) Young&apos;s modulus, (6) Poisson&apos;s ratio, (7) density or apparent specific gravity, (8) modulus of rupture, (9) indirect tensile strength, and (10) creep characteristics. Where possible, an at¬tempt will be made to evaluate each property measure¬ment in relation to the problems of rock mechanics and application of results. TEST SPECIMENS The selection and care of drill core for laboratory testing require some consideration. It is recognized that laboratory-determined properties are not necessarily rep¬resentative of an in situ rock mass property. However, relative information between beds or zones of interest is still valuable information in selecting mining horizons and preliminary design criteria. To provide statistical data the number of drill core samples selected to repre¬sent each of the areas of interest should be from a mini¬mum of three to a maximum of ten test specimens. A judgment must also be made on site as to whether the recovered drill core should be wrapped and sealed in plastic to preserve moisture. On the one hand investiga¬tions of air-dried and saturated specimens have shown that moisture significantly affects the elastic properties and strengths of many rock materials (Obert, Windes, and Duvall, 1946; Colback and Wiid, 1965); on the other hand it is apparent that most core drilling is done with water which may saturate the specimen to a greater extent than in the in-situ condition. Whether or not the decision is made to retain the moisture, the core should be delivered to the laboratory as soon as possible after recovery for subsequent specimen preparation and testing. Specifications Shape: The shape of the specimens influences lab¬oratory testing in two ways: (1) time and cost of sam¬ple preparation and (2) strength of the material. Cy¬lindrical specimens of drill core are by far the least time-consuming to prepare for static or dynamic labora¬tory testing. In addition, the cylindrical shape lends it¬self to a more uniform stress distribution throughout the sample than other shapes, such as rectangles and hexa¬gons. The compressive strengths of various shapes have been studied (Grosvenor, 1963, and Price, 1960), and results indicate that the cylindrical specimens usually provide the highest strength for a given height-diameter ratio. However, reduction in strength from a cylindrical shape to a rectangular in situ pillar is not regarded as significant in relation to other considerations such as planes of weakness in a pillar or safety factors in the design process. Length-Diameter Ratio: The length-to-diameter ra¬tio, LID, has a significant effect on the compressive strength. Various recommendations have been made to use standard LID ratios ranging from 2 to 2.5 to 3 (ASTM, 1975c; ISRM, 1972). However, past work by others such as Obert, Windes, and Duvall (1946) has shown that excellent results can be obtained using LID ratios from 2 > (LID) > >/s. In selecting an LID ratio for testing, one should keep in mind the amount of material available for testing. In many instances, this may be limited. Thus, a shorter specimen such as 1: 1 LID may be necessary to provide enough test data for statistical analysis of results. Sec¬ond, it may be desirable to obtain elastic constants dur¬ing the test. This generally requires instrumentation such as linear variable differential transformers (LVDTs) or strain gages near the center of the specimen. In this case, an LID of 2.5 or 3 is desirable so that the instru

Jan 1, 1982

By Ralph S. Mattson, Frederick T. Hancock

GENERAL DESCRIPTION The Granduc mine is situated on the west side of Granduc Mountain in the Leduc River area of north¬west British Columbia about 51 km (32 miles) north¬east of the town of Stewart. Entry is by means of a 16.6-km (10.3-mile) long haulage adit from the concentrator site at Tide Lake. The principal ore mineral is chalcopyrite. Ore mineralization varies from dis¬seminated to irregular semimassive stringers generally associated with highly folded and sheared biotite-rich sections of metasediments. The ore bodies vary in width from 3.6 m (12 ft) to over 18 m (60 ft) in a zone some 800 m (2600 ft) in length dipping at an average of 75° to the west and plunging steeply to the south. Capping varies in thickness from 0 to over 300 m (1000 ft). SELECTION OF MINING METHOD In the early stages of planning the primary require¬ments to be met by the mining method were: (1) suit¬ability to high output and productivity, (2) adaptability to mechanization in order to minimize operating costs, and (3) minimization of the costs and the development period for preproduction. Considering these, the selection of a mining method was narrowed to a choice be¬tween sublevel long-hole stoping or sublevel caving. A method utilizing backfill was ruled out as uneconomical, especially since mill tailings would not be readily available. At the time, the following facts about the ore body were recognized: (1) the average width of the ore body was 12 m (40 ft), (2) 30% of the stoping blocks were in areas of 6 m (20 ft) or less in width; (3) in many cases, ore zones were located in parallel lenses or were irregular in shape; (4) major faults were present in the hanging wall close to the ore, with minor faults within the different ore zones; and (5) the ore itself was lami¬nated with fractures and jointing crossing such bedding planes. Considering these factors, the two stoping meth¬ods were compared. Sublevel Open Stoping The characteristics of sublevel open stoping are: 1) It is generally not used for widths below 6 m (20 ft) since the ratio of waste development increases as level intervals are reduced to insure good control of long-hole drilling. 2) This method is used where ground is relatively competent. Otherwise more pillar support is required, increasing ore losses or mining costs with pillar recovery. 3) The method is not easily adaptable to parallel ore zones separated by relatively narrow waste bands. 4) Close control of pillar and stope design will per¬mit some degree of dilution control. Sublevel Caving Sublevel caving is characterized by the following: 1) The method can be used for a variety of ore widths, recognizing that 3 m (10 ft) in width may be an economical minimum. 2) It is particularly favorable where wall rock is weak. 3) The method has flexibility so that irregular ore bodies or parallel lenses can be mined. 4) The need to leave pillars for support is eliminated 5) Dilution and tonnage recovery are interrelated. With concern about the stability of the hanging wall and the geometry of the ore bodies, there was a growing favor to choose the sublevel caving method. However, this method was relatively new to Canadian mining practice. Teams were sent to Sweden to tour mines using sublevel caving and to study their methods and any extraction and dilution problems. The objective was to develop cost and performance data and ore recovery grades and tonnages for feasibility comparisons. Next, detailed mine plans were developed covering a three-year period using sublevel caving and sublevel open stoping. Extensive analyses of the development and production costs for each method were made. With sublevel caving, ore losses of 10% with a 20% dilution rate were used. The same ore loss was estimated for sublevel open stoping with dilution varying from 11 to 15%. As a result of these studies, the decision was made to use sublevel caving partly because slightly lower op¬erating costs, together with higher productivity, offset the adverse effects of higher dilution; and partly be¬cause, at the start, there would be less risk in being able to handle the ground, and the method offered more flexi¬bility. Open stoping was not ruled out for testing at a later date. It was recognized that some other method of mining would be required for mining the ore extensions below the glacier, where surface subsidence must be avoided. During the operating life of the mine, open stoping was tested in narrow width ore zones and found un¬satisfactory due to wall failure. A cut-and-fill stope, utilizing run-of-mine waste from development, was also operated on a trial basis. A sequence was finally estab¬lished that permitted ground control; however, produc¬tivity needed considerable improvement in order for open stoping to be considered as a sole alternative for mining below the main haulage level. At the termination of operations in June 1978 over 13 000 000 t (14,500,000 st) had been extracted from above the main haulage level at production rates varying from 3270 to 7250 t/d (4000 to 8000 stpd). Sublevel Caving Methods Two basic methods were used, transverse and longi¬tudinal. The transverse method was used mainly in the upper C ore body in widths greater than 18 m (60 ft), and occasionally as an alternative to the longitudinal method in localized areas where strike faulting inter¬fered with normal development. The longitudinal method was used in ore bodies varying in width from 3.6 to 18 m (12 to 60 ft), with a multilongitudinal varia

Jan 1, 1982

By I. B. Tulu, M. M. Sears

In 2015, 40 longwall mines provided nearly 60% of the US coal production from underground mining methods. This represents a substantial yet gradual increase from just under 50% over the last 5 years. As a result of this increased production share, the percentage of ground-fall-related fatalities in longwall mines has also increased when compared to all US underground coal mines. Additionally, about 80% of ground-fall-related fatalities have occurred in areas where the roof was supported. In an attempt to better understand the status quo of current US longwall support practices, a sample of 25 longwall mines were visited representing nearly 50% of the currently active longwall mines representing all of the major US longwall-producing regions. The resulting data was obtained from a wide variety of overburden depths, geologic conditions, mining heights, ground conditions, support practices, and gateroad configurations. The data collected is reported using both qualitative and quantitative methods. Results from the research update previous efforts in classifying mining accidents and injuries as well as current support practices presented by this author at the 2017 Society for Mining, Metallurgy, & Exploration Annual Meeting. This data provides a necessary background for future research aimed at further reduction of ground fall accidents and injuries.

By I. B. Tulu, M. M. Sears

In 2015, 40 longwall mines provided nearly 60% of the US coal production from underground mining methods. This represents a substantial yet gradual increase from just under 50% over the last 5 years. As a result of this increased production share, the percentage of ground-fall-related fatalities in longwall mines has also increased when compared to all US underground coal mines. Additionally, about 80% of ground-fall-related fatalities have occurred in areas where the roof was supported. In an attempt to better understand the status quo of current US longwall support practices, a sample of 25 longwall mines were visited representing nearly 50% of the currently active longwall mines representing all of the major US longwall-producing regions. The resulting data was obtained from a wide variety of overburden depths, geologic conditions, mining heights, ground conditions, support practices, and gateroad configurations. The data collected is reported using both qualitative and quantitative methods. Results from the research update previous efforts in classifying mining accidents and injuries as well as current support practices presented by this author at the 2017 Society for Mining, Metallurgy, & Exploration Annual Meeting. This data provides a necessary background for future research aimed at further reduction of ground fall accidents and injuries.

By J. P. Sieverson

The Comprehensive Environmental Response, compensation, and Liability Act (CERCLA -commonly referred to as Superfund) was passed into law in December 1980 in the wake of such incidents as Love Canal and the Valley of the Drums. Superfund was originally perceived as a way of cleaning up spills of hazardous substances and/or cleaning up abandoned hazardous waste dumpsites. In February 1981, Michael Cook, EPA deputy assistant administrator for hazardous emergency response, called Superfund "a tremendously powerful law. It could revolutionize the way the environment is protected, but we certainly don&apos;t intend to realize the full potential of the law for some time." These words have proven prophetic for Asarco&apos;s East Helena Smelter.

Jan 1, 1988

By Jessica Elzea, Haydn Murray

The term bentonite was first proposed in 1898 by Knight, a year after he had named this clay taylorite, because taylorite had been previously used for another mineral. The name taylorite was after the Taylor ranch, the site of the first mine, near Rock River, WY, and the name bentonite is from the Benton Shale in which the clay was thought at that time to occur. The Benton Shale was, in turn, named after Fort Benton, MT, located more than 640 km miles north of Rock River. Early in the 20th century, several geologists recognized that bentonite, mainly in beds in Cretaceous and Tertiary rocks, originated from transported volcanic materials. This recognition led to definitions based on origin, the one most widely quoted and generally accepted by geologists is the following definition by Ross and Shannon (1926): "Bentonite is a rock composed essentially of a crystalline clay-like mineral formed by devitrification and the accompanying chemical alteration of a glassy igneous material, usually a tuff or volcanic ash; and it often contains variable proportions of accessory crystal grains that were originally phenocrysts in the volcanic glass. These are feldspar (commonly orthoclase and oligoclase), biotite, quartz, pyroxenes, zircon, and various other minerals typical of volcanic rocks. The characteristic clay-like mineral has a micaceous habit and facile cleavage, high birefringence and a texture inherited from volcanic tuff or ash, and it is usually the mineral montmorillonite, but less often beidellite." The difficulty in applying the foregoing definition to bentonite as an industrial mineral commodity is that it is based on origin and is restricted to an ash, tuff, or volcanic glass parent material. Therefore, deposits consisting of the clay minerals required by this definition, but having uncertain origin or parent materials, cannot properly be called bentonite. Furthermore, many deposits in the western United States and in other countries that have formed from rocks other than the types required by the definition are being mined and sold as bentonite. Perhaps the best definition of bentonite as an industrial mineral is one given by R.E. Grim in a plenary lecture at the International Clay Conference (AIPEA) at Madrid, Spain, June 27, 1972. According to this redefinition, which will be used in this chapter, bentonite is a clay consisting essentially of smectite minerals (montmorillonite group of some usages), regardless of origin or occurrence. This definition solves the problem of the difference between the geologic and industrial usages of the term and overcomes the difficulty in assigning a name to smectite clay that formed from igneous rock other than ash, tuff, or glass, or those of sedimentary or uncertain origin. However, bentonite, when used with this meaning is still a rock term (consisting of more than one mineral), and it will not be possible to distinguish it from fuller&apos;s earth in many instances. One way of classifying bentonite is based on its swelling capacities when wet or added to water. Bentonite having sodium (Na+) as either the dominant or as an abundant exchangeable ion typically has very high swelling capacities and forms gel-like masses when added to water. Bentonite in which exchangeable calcium (Ca++) is more abundant than other ions has much lower swelling capacities than sodium varieties. Some calcium types swell little more than common clay, and most crumble into granular masses in water. Intermediate calcium-sodium bentonites, the so called mixed types, tend to swell moderately and to form gels of lesser volumes than equal masses of the sodium type bentonite. Because of the general relationship of swelling and exchangeable ion characteristics bentonite is commonly divided into the high swelling or sodium, low swelling or calcium, and moderate swelling or intermediate types. The term sub-bentonite (Davis et a]., 1940) is used inconsistently in industry for the low or moderate swelling varieties. The authors believe the use of this term should be discouraged because of its implication of low quality or low value and the lack of a mineralogical or use basis for it. In the United States bentonite is also classified by geographic location and the uses for which it is sold. Inasmuch as most of the low swelling calcium type occurs in states bordering the Gulf of Mexico, this variety is commonly called Southern bentonite. The largest high swelling sodium bentonite deposits and the major producing districts are in Wyoming and adjacent states. Therefore, this bentonite is commonly called the Wyoming or Western type. Such terms as drilling mud bentonite, foundry bond bentonite, and taconite bond bentonite relating directly to use are applied in marketing. Other terms including high and low yield bentonite, high and low gel bentonite, and high and low strength bentonite are also used to distinguish different grades. The varied classifications notwithstanding, bentonite occurs in so many different varieties that some cannot logically be classified according to any of the foregoing groupings. One of these types is hectorite, which is a high swelling lithium-bearing variety of smectite occurring mainly in California and adjacent states. It is, therefore, not a Wyoming type, and it occurs even farther west than the so called western bentonites. Others are bentonites having magnesium (Mg++) or hydrogen (H+) as the most abundant or dominant exchangeable ion. These types are neither sodium nor calcium varieties, and apparently some are low swelling, whereas others have rather high swelling capacities. Still another type of bentonite, the so-called potassium type, K-bentonite, or metabentonite, occurs in Ordovician and other Pa-

Jan 1, 1994

By Gerald H. Luttrell, Mohammad Rezaee, Roe-Hoan Yoon, Rick Q. Honaker, Aaron Noble, Abhijit Bhagavatula, Michael J. Kiser

A field study was undertaken to experimentally measure the concentrations of rare earth elements (REEs) contained in the process streams generated by a group of 20 coal preparation plants located in the eastern USA. For each site, representative samples of clean coal product, coarse refuse, and fine refuse were collected. Each sample was then partitioned into preselected size and density classes by wet screening/sieving and float-sink testing. The resultant products were dried and subjected to laboratory analyses to determine ash contents and rare earth element concentrations including Yttrium and Scandium. A detailed analysis of the database generated by this exercise showed that coal-based products from these preparation plants contained significant quantities of rare earth elements. In particular, the coarse refuse streams currently discarded by the 20 plants examined were found to contain a sufficient tonnage of REEs to satisfy the current domestic demand for these important elements. The data also showed a strong positive correlation between ash content and REE concentration, which suggested that the primary association of REEs in eastern USA bituminous coal sources is likely within fractions containing inorganic impurities. This association was well described using a simple power equation relating ash content and REE concentration. The ratio of heavy-to-light rare earth elements was discovered to be significantly higher in organically rich fractions of clean coal, suggesting that mineral impurities intimately associated with carbonaceous matter have elevated concentrations of heavy rare earth elements. A similar trend was observed for a grouping of rare earth elements (Y, Nd, Eu, Tb, and Dy) that are likely subject to near-term supply shortages. Finally, the database showed that a linear correlation existed between La for many REEs of interest, although there were several notable exceptions for some high-value REEs (Lu, Pr, and Tb).

By Gerald H. Luttrell, Mohammad Rezaee, Roe-Hoan Yoon, Rick Q. Honaker, Aaron Noble, Abhijit Bhagavatula, Michael J. Kiser

A field study was undertaken to experimentally measure the concentrations of rare earth elements (REEs) contained in the process streams generated by a group of 20 coal preparation plants located in the eastern USA. For each site, representative samples of clean coal product, coarse refuse, and fine refuse were collected. Each sample was then partitioned into preselected size and density classes by wet screening/sieving and float-sink testing. The resultant products were dried and subjected to laboratory analyses to determine ash contents and rare earth element concentrations including Yttrium and Scandium. A detailed analysis of the database generated by this exercise showed that coal-based products from these preparation plants contained significant quantities of rare earth elements. In particular, the coarse refuse streams currently discarded by the 20 plants examined were found to contain a sufficient tonnage of REEs to satisfy the current domestic demand for these important elements. The data also showed a strong positive correlation between ash content and REE concentration, which suggested that the primary association of REEs in eastern USA bituminous coal sources is likely within fractions containing inorganic impurities. This association was well described using a simple power equation relating ash content and REE concentration. The ratio of heavy-to-light rare earth elements was discovered to be significantly higher in organically rich fractions of clean coal, suggesting that mineral impurities intimately associated with carbonaceous matter have elevated concentrations of heavy rare earth elements. A similar trend was observed for a grouping of rare earth elements (Y, Nd, Eu, Tb, and Dy) that are likely subject to near-term supply shortages. Finally, the database showed that a linear correlation existed between La for many REEs of interest, although there were several notable exceptions for some high-value REEs (Lu, Pr, and Tb).

By D. A. Lee

The selection of control system equipment for a mineral plant is based on several criteria, including opera tor interface, supervisory capabilities, ease of maintenance, ease of programming and configuration, compatibility with auxiliary control equipment, and total cost. The paper discusses the technical evaluation procedure with respect to control system equipment available today.

Jan 1, 1988

By Hans von Michaelis

Welcome to RANDOL GOLD FORUM 88. It is clear from the list of delegates and speakers that this conference will lead to excellent discussions of the latest developments in this fast-moving industry. Less than a year ago Randol International Ltd. published an eleven-volume report titled "Innovations in Gold and Silver Recovery - Phase 111". In the short space of time since then, many new developments have been noted, many of which will be described in this Forum. I believe that some of the more significant innovations currently under development are those that address the following:

Jan 1, 1998