Search Documents

By R. J. Sweigard

Three case studies were undertaken to investigate the role of land use potential evaluation in reclamation planning and to determine the impact of regional differences on the evaluation process. The three surface mines studied were representative of operations in the Appalachian, Interior, and Northern Great Plains provinces. The scope of the investigations included a survey of regional characteristics, a detailed investigation of the mining operations and site conditions, and an assessment of local land use planning activities in the area of the mine. Special attention was given to key factors that presently determine the use of reclaimed land. Also, for each case study, the postmining land use potential was evaluated using site planning principles. Specifically, the environmental, economic, and social impacts of several potential postmining land use plans were considered.

Jan 1, 1983

By Mina M. Shinouda

Brightwater West (BT4) represents the state of the art in utility tunneling, namely a long relatively small diameter, soft ground tunnel, with no intermediate shafts, under significant groundwater pressures, requiring very precise survey control in order to hit a small exit window. The tunnel is over 6.4 km (4 miles) in length, is expected to encounter active earth pressures of over 5 bars in glacial geology, and a planned hole through into a shaft eye constructed at 45.7 meter (150 feet) below the water table. Despite the fact that all of these challenges have been previously overcome in larger diameter tunnels, the technical solutions are much more challenging in a smaller diameter due to the lack of space available for implementing the equipment and techniques required. In addition to the technical challenges, the project is faced with many of the constraints designed to minimize the impact of these types of projects on the neighboring community and environment. The work shaft for BT4 is within 15.2 m (50 feet) of Puget Sound and is on a site that was previously occupied by petroleum storage tanks, and all of the tunnel muck has to be removed from the site by barge as trucking is not allowed by contract. The paper addresses the work performed during the preparation for tunneling stage of this project both in assembling the TBM and in preparing the site for its arrival.

By Morgan M. Sears, Mark Morris, Joseph Bright

In an effort to advance the science underlying modern coal pillar stability analysis, researchers at the National Institute for Occupational Safety and Health are currently involved in research aimed at better understanding the impact of an in-seam rock parting on the strength of coal pillars. The purpose of this study is to determine a suitable virtual mining height that could be applied using current pillar stability analysis tools. To accomplish this, the boundary element model LaModel was used to back analyze data collected on pillar performance in a room-and-pillar panel at the Maple Eagle Mine located in Southern West Virginia. In a previous work, data collected from borehole pressure cells (BPCs) and extensometers were taken from three instrumentation sites. Data collected from the back bleeders were used to measure the rear abutment stresses, and data collected from two instrumentation sites in the wraparound bleeder were used to measure the front and side abutment stresses as well as the peak strength and performance of the slabbed leave pillar. The utilization of two nearly identical instrumentation sites in the wrap-around bleeder provided much needed repeatability of the obtained measurements. In this study, the data collected from BPCs at the three instrumentation sites was calibrated to match the Bieniawski pillar stress gradient. To model the measured pillar behavior, the LaModel program was selected due to its capability of being directly comparable to the Analysis of Retreat Mining Pillar Stability (ARMPS) and Analysis of Coal Pillar Stability (ACPS) programs. The model was then calibrated to match the measured abutment extent and abutment stress. Finally, the model was validated by reducing the modeled mining height until the yielding of the slabbed leave pillars in the model matched what was measured in the field. The final calibrated mining heights show that a reduction of the shale parting thickness, not including any clay layers, of 52% is applicable. This research study provides the first known measurement of the ARMPS/ACPS “50% Rule” and its applicability to this panel of the Maple Eagle Mine. This finding provides a proof of concept and could have significant implications for future research.

Feb 1, 2024

By Collon C. Kennedy, Frances C. Hartogh, C. Joel Casburn

INTRODUCTION During the nineteenth century, the federal mining law was enacted with the objective of promoting the development of the western United States by providing unrestricted access to vast areas of federal land for mineral exploration. Prior to the advent of comprehensive federal, state and local land use plans, there was little, if any, regulation or restriction of mineral exploration activities. Today, the laissez-faire policies of the past that encouraged mineral exploration have gradually given way to the public's legitimate concerns regarding environmental protection, multiple use and planned land development. As a result, the contemporary prospector confronts a maze of statutes, ordinances and regulations with which he must comply to obtain the requisite approvals and permits before commencing mineral exploration on federal, state or private lands. This presentation will provide a broad overview of the exploration permitting process. The first section of this paper recommends certain general management practices to follow when attempting to obtain exploration permits. The second section presents two hypothetical cases, one involving a drilling program on private property in California and the other involving a drilling program and the removal of a bulk sample for metallurgical tests from federal land in Nevada. The cases are used to discuss jurisdictional issues and application of certain federal, state and county laws and regulations that pertain to mineral exploration. The final section contains a brief analysis of three important recent United States Supreme Court decisions. These decisions address the scope of the federal pre-emption doctrine as it applies to activities conducted on unpatented mining claims and the constitutional limits of permissible state and local land use and zoning regulations. PERMITTING PRACTICES The environmental impacts associated with mineral exploration generally result from the construction of drill sites, roads or trenches. Consequently, after the regulatory authority has considered the issues of permissible land use, the primary emphasis of the permitting process is to address problems related to pre-construction site identification and clearance, and post-construction site reclamation. The approaches taken to address these and other related issues vary with the scope of proposed work, the site, the appli-

Jan 1, 1987

By Paul Mitchell, Amy Wheaton, James Rybock

Acid rock drainage (ARD) represents one of the most intractable problems faced by the non-ferrous metal and coal mining sectors, and the creation in the recent past of a number of high-level national and international initiatives reflects the growing concerns of industry, government and other stakeholder groups. ARD is certainly considered one of the most serious environmental impacts caused by mining and the industry's greatest environment-related technical challenge. Additionally, the global depletion of non-acid generating oxide ore deposits and the increasing dominance of sulphide ores means that the potential for ARD incidents will continue to increase. Once initiated, the cycle of chemically and biologically mediated and catalysed reactions leading to ARD generation is difficult to stop. While there is evidence to suggest that the degree of contamination of ARD will decrease rapidly within a relatively short timeframe (Wood et al., 1999), experience in historic mining regions of the world indicates that the problem may persist for centuries at certain sites. Current best practice in dealing with ARD puts the emphasis on prediction and prevention, planned from the outset of the operation and integrated with each phase of the mine site life cycle. The elements that constitute best practice are becoming more clearly defined and as this process of clarification continues industry will undoubtedly accelerate the process of best practice implementation, burying at last the image of mining as a despoiler and polluter of landscapes, an image based on past, rather than current, practices. However, it is equally clear that despite the best efforts of industry and regulators, many sites will continue to generate ARD during operation and following closure - in many cases, a legacy of ARD has been derived from operational and strategic decisions made decades ago, before the risks and impacts of the self-sustaining cycle of ARD generation were properly understood. Add to this ARD generation from poorly managed operations and from historic and abandoned sites, and it becomes clear that the treatment of ARD will be required for the foreseeable future to protect water quality, and ecosystem and human health.

Jan 1, 1999

By R. Bruce Thorndycraft

This paper will describe several modifications to design of con­ventional oxide gold heap leaching. They are targeted at reduc­ing costs and simplifying heap operations. These modifications were conceptualized during consulting work on over 90 differ­ent heap leaches. In 1995, a unique opportunity arose to imme­diately apply all of these design concepts to the permitting and construction of a new facility at the American Girl Mine in southeastern California. American Girl Mine has operated since 1987. In April 1995, the mine faced a situation with grave consequences for cash flow. Approval for mining of a new ore zone, Oro Cruz, had just been granted, after lengthy delays by California regula­tors. All existing pad space would be filled by October. Only 6 months were available, and new pad siting and design were still undecided. Permitting of a new pad had not begun. Options were quickly reviewed. A strong criteria for pad site selection and design was ease of permitting. There was also a strong desire to install a system that would achieve better met­allurgical recovery and reduced operating costs, compared to previous heaps at this mine. One site offered the best chance for rapid permitting. It was the site of the original 1987-90 heap leach. This already dis­turbed ground contained 1.6 million tons of heaped ore. The old heap had just completed detoxification and was about to be signed off as a Group C waste, ready for reclamation. Instead of recontouring and revegetating the old heap, which the reclamation plan anticipated, we offered BLM and the County something even better. We proposed to off-load much of the detoxed old heap, and reuse the space. The off-loaded material would be back-filled into the original open pit, imme­diately adjacent. While the footprint of the proposed new pad was much larger, the reuse of disturbed ground, and backfilling of the open pit, had very strong appeal to the regulators. Our permitting strategy included the technical design of the proposed new facility. Many of the new design details also appealed to the regulators, particularly the "zero active ponds" concept.

Jan 1, 1996

By T. Stuczynski

In the past ten years about 3000 wastewater treatment plants have been built in Poland. The result of this development has been a massive increase in overall sludge production. According to data supplied by the Ministry of Environmental Protection, 400,000 dry tons of sludge are generated every year in Poland (Koblak-Kalinska 1996). Still it is difficult to estimate the amount of sludge, which is used in agriculture or for reclamation purposes. However, it can be assumed that this comes to no more than 10 percent of all sludge produced in Poland on a yearly basis. Thus it became obvious that an urgent solution to this problem was needed. Local authorities in Silesia realized in the early 90?s that a demonstration was necessary to encourage the proper utilization of sludge. This was the basis for establishing the Biosolids Subpart of the Silesia Project, which addressed the use of biosolids in the reclamation of mining and smelting dumps (Stuczynski et al. 1996). Metal waste sites themselves are known to contain more than 87 million tons of waste (Pistelok et al. 1995). Each year this amount increases by approximately 400,000 tons. We realized that a simple solution for stabilizing these sites would be to cover them with vegetation in order to reduce leaching of toxic elements, as well as to keep metallic fugitive dust from entering the environment. The reclamation of smelter waste sites, which was carried out within the framework of the Silesia Project was a joint effort of local government, industry and international research institutions/agencies, including the US Environmental Protection Agency (EPA), the Center for Research and Control of the Environment (OBIKS), Virginia Polytechnic Institute and IUNG. One of the goals was to evaluate the possibility of adapting the rules of sludge management currently used in the United States to conditions commonly found here in industrial regions of Poland. However, the main objective of the Silesia Project was the development of guidelines concerning all aspects of sludge use for the reclamation of degraded lands and waste sites. Biological aspects related to reclamation of metal waste with the use of biosolids will be discussed in this paper.

Jan 1, 2002

By I. Sanchez

The development of the recent generation of large mining projects in South America has been challenging in many ways, but especially in the management of water in all its aspects. As a result, a number of projects have experienced difficulties and in some cases significant delays due to a lack of a clear and approved definition of the supply, use and discharge of water from mining and processing sites. The development of the recent generation of large mining projects in South America has been challenging in many ways, but especially in the management of water in all its aspects. As a result, a number of projects have experienced difficulties and in some cases significant delays due to a lack of a clear and approved definition of the supply, use and discharge of water from mining and processing sites.

Feb 23, 2014

By Mark E. Gershon

Conventional methods of drillhole site selection are reviewed briefly. Two approaches using geostatistics are then discussed, both of which have been shown to yield improved results. Finally, a branch and bound algorithm is described which will select the best locations for drilling from a user specified number of possible drill sites. Two options are discussed. First, the user can specify a maximum drilling investment or a maximum number of drillholes and the program will select the locations yielding the minimum estimation variance. This amounts to getting the most for a given investment. Alternatively, a maximum tolerable estimation variance can be specified and the program will select the number and location of the drillholes to obtain the desired information at a minimum cost. Another benefit of the approach is the quantification of the tradeoffs between investment and information obtained.

Jan 1, 1983

The solution mining review did not arrive in time for publication in the May issue. The term solution mining is commonly used to refer to heap leaching, dump leaching, in situ mining and bore hole slurry mining technologies. The US Bureau of Mines is continuing with research in these areas. Commercial application of these technologies is progressing. There is an ongoing cooperative research project between the Bureau of Mines and the Santa Cruz Joint Venture to evaluate in situ copper mining at a field site near Casa Grande, AZ. The project is currently in the environmental permitting stage. The Bureau is preparing an environmental assessment for the project as part of the National Environmental Policy Act. The Bureau is also continuing with laboratory experiments to study the leaching characteristics of atacamite ore from the field test site, as

Jan 1, 1993

By Rudy Rogers

When Gas hydrate formation rates have two steps: a nucleation induction step and an agglomeration step. Hydrate induction in distilled water is extremely slow because of lack of nucleating particles. Our laboratory found that synthetic anionic surfactants greatly improve both hydrate induction and agglomeration because the surfactant?s hydrophilic head absorbs water molecules and the hydrophobic tail absorbs hydrocarbon gas molecules, creating necessary nucleation sites. Vast hydrate deposits inhabit seafloors. What is the seafloor hydrate nucleating mechanism? We find that nano-particles of smectite clays (bentonite and nontronite) are hydrate-nucleating sites in sea-water-saturated, packed porous media, especially when trace quantities of anionic biosurfactants adsorb on the clay particles. Microbes and their bioproducts proliferate around seafloor gas hydrate accumulations. The seafloor microbe-mineral-hydrate synergy is explored in this paper. Keywords: gas hydrates, biosurfactants, crystal nucleation, smectites

Jan 1, 2008

By T. Motzer

Sustainability management and reporting plays an important role in controlling and communicating a company's efforts in sustainable development. A variety of standards comprising a multitude of indicators often require similar information but with different data quality, level of detail and coverage. This may lead to inconsistencies in external communication because of the difficulties in collection and aggregation of data from different company sites and organisational levels. Using a central database system accessible via internet makes the process of data management more efficient: All relevant information can be collected on-site, with a defined data quality, credibility and consistency. Any type of sustainability indicator can be calculated automatically, once the data is collected. Individual analyses and predefined reports, e.g. GRI G3, can be easily generated and immediately published, making your sustainability communication transparent and reliable.

Jan 1, 2007

By Steven W. Hunt, Ronald E. Heuer, Safdar A. Gill

A 3.3 m (11 feet) diameter, 51 m (168 feet) deep temporary steel casing which had been sunk within glacial soils buckled and collapsed on July 29, 1985. The collapse occurred at the CT-8 Dropshaft site in Milwaukee while two workmen were contact grouting outside the casing in an attempt to stop groundwater inflows through a bottom plug. This paper describes the soil and groundwater conditions at the site, the casing design, the method of shaft construction, and probable causes of the buckling failure. Specific aspects of the paper include: slurry method of shaft excavation and casing installation, soil creep, earth pressure due to three dimensional arching, and buckling strength of a casing surrounded by slurry rather than grout and firm soil. The paper should be of interest to designers and constructors of temporary ground support systems for deep shafts.

Jan 1, 1995

By E. M. Frizzell

In an effort to economically and efficiently enhance the erosion control aspects of present surface coal mine reclamation practices, the US Bureau of Mines has recently completed a two-phase research program wherein irrigation strategies and equipment developed under the first phase were field tested on three surface coal mine sites. The fundamental basis for the use of irrigation as a reclamation tool is to provide the plant moisture requirements as a supplement to prevailing natural precipitation, and thereby support the natural growth of drought-hardy native vegetation. Portable solid-set irrigation equipment and several irrigation strategies were tested on large 6-ha (15-acre) sites in Montana, Wyoming, and New Mexico. Results of these tests will be presented which include daily irrigations, precipitation levels, soil moistures, climatic data, and density cover and biomass of the native plants.

Jan 1, 1987

By David Brown, Glen Hall, Ken DeVos, Frank Barone

Dredging and Flooding was completed on the Falconbridge Limited "New Tailings Area" in the period from 1996 through 1998, as part of their site closure measures. Part of the decision making process and closure planning was water quality prediction, including oxidation and diffusion modelling. The purpose of this modeling was to define the potential water quality that would result during and after dredging. A significant body of research on the geochemistry and oxidation kinetics of this site had been compiled. The results of the modeling provide practical insight on the potential water quality that may be expected. Water quality in the pond has steadily improved since flooding was completed with the exception of short term peaks during spring runoff. Aquatic vegetation is appearing through natural recovery and transplanting of local species, and colonies of minnows are now observed in the ponds.

Jan 1, 2000

By Günter Strappler, Max John

When tunneling through karstic terrain, diverse and complex karst structures are to be expected. By means of drilling ahead of the face using drill jumbos, these structures can be detected to such a degree that by applying proper support measures both open karst cavities and karst holes surrounded by boulders embedded in soft rock can be mastered without causing any break-outs. Support measures such as spiles ahead of excavation, sealing off cavities, back?lling with sand, etc. have to be planned schematically and adapted to the dimensions and formations of the karst structures on site. An essential requirement for a smooth excavation procedure is the availablility of all necessary tunneling equipment for excavation by drill and blast as well as for excavation of soil, with experienced tunnel engineers being in charge of any adaptions on site.

Jan 1, 2003

By B. Grosso

The National Italian Regulation concerning environment protection imposes that industrial areas are provided with systems aimed at preventing the circulation of contaminated groundwater. These systems can be static or dynamic and operate basically by intercepting the contaminated flow. Their effectiveness, realization time and costs depend on the intervention type and on the features of the specific site. The selection of the best solution is complex and the results obtained by this selection may be affected by residual risks related to the uncertainty of the hydrogeological and geotechnical characterization of the site. With regard to the industrial area of Portovesme, located in the south of Sardinia, the paper presents the analysis of alternative interventions aimed at the protection of the groundwater. The attention is focused on the evaluation of their effectiveness, impact on environment and, finally, time and costs of construction.

Jan 1, 2008

By Susumu Ukita

We have developed first a conveyor belt for transporting large lumps, i.e. Rock Belt successfully, in June 1976. The First Rock Belt had been delivered to Myodani site of Kobe City Developing Board in Japan, and its' successful operation has attract keen interests in customers from over the world as well as Japan. However, this First Rock Belt was removed in arch '81, viewing it has satisfactory expired its service life of about five-year, and also original location of this belt become to be far from the site due to long-years earth collecting work. Taking this opportunity, we introduce the Second Rock Belt applied for Rock Belt Loader as ell as three types of application of our Rock Belt working for rationalization of quarry of major company in Japan, and, view the prospect of Rock Belt:

Jan 1, 1981

By M. E. Gershon

Conventional methods of drill hole site selection are reviewed briefly. Two approaches using geostatistics are then discussed, both of which have been shown to yield improved results. Finally, a branch and bound algorithm is described which will select the best locations for drilling from a user specified number of possible drill sites. Two options are discussed. First, the user can specify a maximum drilling investment or a maximum number of drill holes and the program will select the locations yielding the minimum estimation variance. This amounts to getting the most for a given investment. Alternatively, a maximum tolerable estimation variance can be specified and the program will select the number and location of the drill holes to obtain the desired information at a minimum cost. Another benefit of the approach is the quantification of the tradeoffs between investment and information obtained.

Jan 1, 1985

Newmont?s Twin Creeks Mine, located in northern Nevada, is producing gold ore from surface mining operations. The ore is currently processed at three different on site facilities depending on the ore type and the grade. The processing facilities operate under stringent geochemical blending constraints that must be met from mine ore deliveries and off site sourced ore. To analyze various strategic options, the technical team utilizes the mathematical optimization approach. However, due to the size and the complexity of the operation, there are unique challenges in optimizing life of mine production scheduling. This paper describes those challenges and the methodology developed to take advantage of different scheduling software systems that effectively compensate each other and result in reasonable guidance. The paper also describes how those scheduling results are reflected in detailed mine plan and cost estimate work.

Feb 27, 2013