Search Documents

By Harry R. Nicholls

As part of the pre- and post - shot mine examination at Project GNOME , acceleration data were recorded underground from a series of chemical explosive shots . The cube root of the charge weight was used to scale acceleration and distance because charge weight was not constant . Regression analysis of particle acceleration - distance data gave the following propagation equation : A W1 /3 = 5.10 x 105 ( R / W¹ / 3 ) −2 .43 The quantity A W1 /3 is scaled particle acceleration expressed in g's - lbs¹ / 3 , and R/W1 /3 is scaled distance expressed in ft / lbs¹ /3 Data obtained from the nuclear explosion were scaled and fall within one standard deviation of the calculated propagation law for the smaller shots . Cube root scaling laws were adequate to group acceleration data from explosive charges varying by a factor of more than 1 x 10 in charge weight and over shot - to - gage distances varying from 100 to 46,000 feet . Data obtained from a series of small tests provided sufficient data from which reliable predictions of acceleration could be made for the large nuclear explosion .

Jan 1, 1964

By Thomas M. Kohler, Gerald L. Finfinger, Gregory M. Molinda

The Bureau of Mines has completed an investigation of the effectiveness of methane drainage in the Lower Sunnyside Coalbed at Kaiser Steel Corp.'s Sunnyside No. 1 Mine in Utah. Most of the previous at- tempts to drain methane gas using long horizontal holes were conducted in the Eastern Coal Province. From the high degree of success realized in these efforts and the large body of knowledge gained from associated research, it seemed natural to extend the technology to western coalfields. Previous work had indicated that properties affecting gas drainage were variable in the Sunnyside Coalbed. In an attempt to characterize these properties, four degasification holes were drilled from the out- side entries of an advancing section. The holes were drilled to lengths of 780, 1,680, 1,315, and 1,047 ft and produced initial flow rates of 50,000, 180,000, 340,000, and 240,000 f t3/d, respectively. A total of over 300 million f t3 of commercial-quality gas has been removed from the Sunnyside Coalbed. The four holes have reduced face emissions by 78 pct.

Jan 1, 1986

By Gordon T. Austin

The combined value of production of natural abrasives, which includes tripoli, special silica stone, garnet, staurolite, and emery, increased about 9% in 1988. In the case of emery, the increase was due to an increase in unit value of the material produced. The increase in the value of garnet and staurolite production was simply the result of an increase in the quantity of materials produced. However, special silica stone experienced both an increase in unit value and quantity produced. The nonmetallic manufactured abrasives industry, which includes only silicon carbide and fused aluminum oxide in the reported statistics, enjoyed the best production year since 1981 in terms of total quantity produced. Production increased 22% in quantity and 16% in value com-pared with those of 1987.

Jan 1, 1990

By Orlando Martino

This regional report covers the mineral industries of Canada and 40 countries and areas in Latin America and the Caribbean Basin. Also included is a brief description of the mineral potential of Antarctica. The Latin American region encompasses an area twice that of the United States. Latin America and Canada have a rich and diversified endowment of mineral fuels, metals, and industrial minerals. Tables 1 and 2 provide a summary view of Latin America and Canada's output of its major mineral commodities in world mineral supply in 1990 and 1991. Table 3 shows the relative importance of a selected group of minerals produced in Latin America in the world mineral economy.

Jan 1, 1993

By F. Albayrak

This report is a study of the impact of Federal laws and regulations on the domestic supply of metallic and nonmetallic minerals. The study was confined to pertinent environmental legislation and the recently enacted Federal Mine Safety and Health Act of 1977. Emphasized were the legal requirements placed on individual selected mineral industries, and the economic impact of these requirements. A certain amount of attention was also directed to the particular environmental and health and safety problems generated by selected mineral industries. The study also pinpointed a list of major problem areas having significant impact on the domestic mineral supply.

Jan 1, 1978

By W. K. Collins

Engineered scavenger compounds (ESC's) developed by the U.S. Bureau of Mines are a novel class of compounds that selectively can recover a desired element from a solid or molten alloy. Lithium titanate (L2Ti307 or Li2O?3Ti02) is used as an ESC to recover lithium (Li) from aluminum-lithium (Al-Li) alloys. X-ray diffraction measurements have shown that Li2Ti307 undergoes a phase change during scavenging from an orthorhombic structure to a hexagonal structure. This change is due to the incorporation of lithium in the matrix of the material and the effect of temperature. Although both phases are metastable, the hexagonal phase that forms during the scavenging of lithium from Al-Li alloys appears to be the more stable phase. Recovering lithium from the ESC by electrodeposition does not cause the structure to revert to the orthorhombic phase. The orthorhombic and the hexagonal structures of Li2Ti307 have similar scavenging capacities for lithium. This report proposes a new mechanism for the phase transformation.

Jan 1, 2010

By A. J. Barry

To determine the torque-load relationship for SIB-inch (nominal)-diameter roof bolts, the Bureau of Mines tested 5 makes of expansion shells and 2 types of bolts (regular and high-strength) in 2 sandstone and 2 shale mine roofs. Unused flat-steel bearing plates in as-received condition were used in these tests. The relationship between torque and load was found to be approximately 50 pounds of load per foot-pound of torque for both the regular and high-strength bolts. This relationship is valid up to 130 foot-pounds for the regular bolts and up to 175 foot-pounds for the high-strength bolts. A torque of 130 foot-pounds on a regular bolt will produce a load of 6,150 ± 1,910 pounds 90 percent of the time, and a torque of 175 foot-pounds on a high-strength bolt will produce 8,050 ± 2,750 pounds 90 percent of the time. Above these values, the torque-load relationship tends to be erratic due to binding between the bolt and plug threads. Binding causes excessive torque to be expended in producing torsion in the bolt rather than tension. This torsion adversely affects the yield load of the bolt. Therefore, the installed torques should not exceed the 130-and l75-foot-pound values. A statistical analysis of the data showed that the torque-load relationship was not significantly affected by the type of bolt or expansion shell unit but might have been affected by the type of rock.

Jan 1, 1956

By Gordon H. Dechman

This report presents the concept, design, and testing of a sonic velocity monitoring system for the early detection of slope failure in open pit mines. The heart of the system is a device for producing reproducible sonic signals in rock. Because changes in the velocity of sound through rock near the top of the pit wall are a measure of extent and rate of fracturing of the rock, velocity histories obtained from periodic, automatic sonic velocity surveys provide positive information about developing slope instability.

Jan 1, 1976

By A. D. Hahn

This report describes and gives the results of an examination by the Federal Bureau of Mines of ilmenite-bearing placer sand deposits in the 24-mile long valley of Otter Creek, Kiowa and Tillman Counties, Okla. Drilling and sampling was completed in three periods between October 1956 and September 1957. Mineralogic studies and mineral-dressing tests on recovery of ilmenite and other heavy minerals from composited samples of the sands were made in Bureau of Mines laboratories at Rolla, Mo., in 1957 and early 1958. Otter Creek rises in and drains the southwestern extremity of the Wichita Mountains, which are represented locally by knolls and ridges of gabbro and granite surrounded by plains floored with flat-lying Permian red beds. The valley fill consists of a basal sand-clay component, derived from weathering of the igneous rocks, and an overlying silt-clay alluvium. Ilmenite is present in significant quantity and recoverable grain size only in the basal sand-clay.

Jan 1, 1960

By Walter W. Kaufman

The braking performance of underground, rubber-tired, non-coal mining vehicles is evaluated. Surveys of mining equipment and braking manufacturers and underground stopping tests are discussed as they relate to this evaluation. Stopping performance recommendations are included as well as related aspects of roadway construction and runaway vehicle protective devices.

Jan 1, 1977

By D. L. Soreck

The hazards to the public posed by abandoned mine shafts are well documented. As private development encroaches on previously mined areas, the potential for fatalities and serious injuries from abandoned mine shafts increases. The U.S. Bureau of Mines has conducted research into cellular concrete as a material for sealing these openings. The current work involves testing the characteristics of cellular concrete before and after it had been pumped or dropped from different heights into a simulated mine shaft. Cellular concrete was pumped vertically up to and subsequently dropped from heights of 18 and 37 m into concrete forms. Wet density measurements were made at multiple sampling points in the test circuit. Air content determinations and uniaxial compressive strength testing were conducted. Research results showed significant loss in air content and changes in the characteristics of cellular concrete during pumping or dropping from various heights. Recommendations on effective use of cellular concrete for sealing abandoned mine shafts are made.

Jan 1, 2010

By Keith L. Harris

The economy continued to expand during the second quarter, but at a much slower pace than expected. According to latest estimates released by the Department of Commerce, the real gross national product (GNP) grew at a seasonally adjusted annual rate of 0.6% compared with a revised growth rate of 3.8%2 for the first quarter of 1986 and 2.3% for the second quarter of 1985 (table 1). The strong growth of personal consumption expenditures, Government purchases of goods and services, and residential investment was moderated by the growing trade deficit, declining investment in business inventories, and the continuing lag in nonresidential investment. Much of the decreased capital spending for the nonresidential sector for the first and second quarters resulted from reduced petroleum exploration and drilling in response to low petroleum prices. Capital spending and trade continue to be areas of weakness for the economy. Real new plant and equipment expenditures for 1986 are estimated to be 1.3% below those of 1985 (table 2). Real net exports of goods and services decreased $24.6 billion, as exports declined 5.6% and imports grew 16.5%. About two-thirds of the $19.3 billion increase in imports was in petroleum and petroleum products, which, because of their lower prices, should help the economy in the future. In response to the sluggishness of the economy, the Federal Reserve System reduced its discount rate from 6.5% to 6% in early July. Inflation, as measured by the fixed-weighted GNP price index, declined from a revised 2.5% in the first quarter to 1.9% in the second quarter because of significantly lower energy prices.

Jan 1, 1986

By Douglas F. Scott

This case study provides an example of how social marketing was applied to meet the needs of business customers. Federal regulations require that all companies develop a written program to track hazardous chemicals at their sites. The HazCom Writer, created by the National Institute for Occupational Safety and Health (NIOSH), is a software tool designed to help companies prepare their required Hazard Communications (HazCom) written plan and list all hazardous chemicals at the company's worksite. The social marketing goal was to provide a product for small- to medium-sized companies to use for federal HazCom rule compliance. The HazCom Wm'ter is a direct NIOSH response to customer and stakeholder needs (including the Mine Safety and Health Administration, the mining community, and Occupational Safety and Health Administration- regulated companies).

Jan 1, 2009

On November 9, the Reynolds Metals Company cut production by 12 at its primary aluminum smelters at Troutdale, Oreg., and Longview, Wash., as a result of an earlier 25% power cutback by the Bonneville Power Administration due to lower than normal stream flow in September, the Aluminum Company of America had closed one potline at its Vancouver smelter because of the power cutback. Nearly 700 union workers at Anaconda Aluminum Company's primary aluminum smelter at Sebree, Ky., walked off the job when their contract expired or, November 15, after rejecting a proposed 3-year contract. The smelter has an annual capacity of 180,000 tons mid accounts for 50% of Anaconda's aluminum production. No talks are scheduled.

Jan 1, 1979

By Robert H. Peters

Groundfall accidents have been the leading cause of fatalities in the underground coal mining industry for many years. Statistics from the Mine Safety and Health Administration (MSHA) indicate that approximately half of the victims of these fatal accidents were in an area where no devices had been installed to support the mine roof. This report was prepared by the U.S. Bureau of Mines to provide guidance to operators of underground mines concerning the use of techniques that may help to keep miners from going under unsupported mine roof. The report is divided into two major sections. The first section reviews the findings from several areas of empirical research pertaining to strategies for convincing employees to avoid unsafe acts and/or adopt self-protective behaviors. The strategies are (1) incentives and feedback, (2) disciplinary actions, (3) training (primarily fear communications and behavioral modeling), and (4) nondirective techniques. This literature review has a broad focus and should be helpful in making decisions about how to encourage a wide variety of types of self-protective behaviors. The second major section of the report presents an analysis of each strategy's potential for keeping miners away from unsupported roof.

Jan 1, 1991

By A. J. Farstad

Characteristics of metal/non metal mines were evaluated to determine the suitability of applying the U.S. Bureau of Mines electromagnetic location system to the problem of locating trapped mines in metal/non metal mines. Statistical distributions of mine depths and overburden conductivities show that the existing USBM EM system is inadequate for most metal/non metal mines. Alternate approaches to trapped miner location in deep mines were identified and subsequent field tests were conducted at six (6) mines to evaluate their feasibility. The approach considered to be the most promising is one which utilizes the existing manpack transmitting system, modified slightly for a dual frequency output, in conjunction with a sophisticated signal processing receiver on the surface. The main advantage of staying with a "through the earth" approach is that the underground equipment can be kept simple, easily maintained, light-weight and inexpensive.

Jan 1, 1979

By John G. Kovac

A computer simulation has been developed to estimate the chances of a miner making a successful escape while wearing a SCSR. The model takes into account: (1) training in the use of SCSRs, (2) apparatus integrity, and (3) the oxygen cost of a mine escape. This Bureau of Mines report examines survival odds for a prototypical escape, and illustrates how these odds change when SCSR training is improved.

Jan 1, 2009

By James R. Aggson

This Bureau of Mines report presents a finite element analysis of roof stresses associated with a 4-foot-high by 18-foot-wide underground coal mine entry. This analysis starts with known loading conditions determined in an underground coal mine in West Virginia and is extended to other possible underground loading conditions. The roof failures predicted by the finite element analysis under known loading conditions correlate well with the roof failures observed underground. The most probable failure modes are identified for the various loading conditions considered. Various failure preventive measures are discussed.

Jan 1, 1979

By David K. Hylbert

This study was designed to investigate roof falls in room-and-pillar drift coal mines and to determine geologic methods for predicting unstable roof conditions. The study area was located in Harlan County, Kentucky and the Bailey Creek (Harlan coal bed) and Highsplint (Darby coal bed) mines were selected for study. Correlations were made laterally between surface outcrops and within the mines using lithologic and trend analysis criteria. Lithologic criteria compared cyclic changes in roof strata. Results indicated that roof falls are associated with zones of weakness within or between five vertical cycles recognized. Abrupt lateral facies changes occur. In the Highsplint mine the roof was classified in four categories or conditions using 98 rib sections for control. Structure contour and isopach maps were used to project axial trends of the sandstone roof. A roof-fall zone was examined using ten NX cores taken from the roof and included lithologic, petrographic and clay mineral studies. At the Bailey Creek mine roof failure was caused by the heading direction being driven subparallel to paleochannel directions. Computer programs were used in trend analysis studies. Cross-bedding, paleo-channel trough axis and sole mark studies indicated a 350 discrepancy between surface and in-mine trough axes at Highsplint. A direct relationship between joint and "slip" frequency and direction with sandstone roll trends was found. Surface joints compared well with drainage Segments, hilt did not correlate with roof falls in areas of mines under overburden in excess of 600 feet.

Jan 1, 1977

By Alastair M. Lumsden

A study was initiated to examine the ways in which a number of foreign countries classify and regulate metal/non-metal mines which experience problems due to naturally-occurring flammable gases. Twenty countries were selected for study, and useful information was obtained from sixteen of these. Nine countries were visited (five of them twice) to hold meetings with representatives of government mine regulatory agencies and mine operators, and to visit mines encountering methane and other gases (carbon dioxide, nitrogen). In the later stages of the study seven gassy metal/non-metal mines in the United States were visited so as to provide a basis for comparison, and hence the evaluation of both the U.S. and foreign gassy mine regulations. In addition to obtaining copies of the mining laws and regulations of a number of foreign countries, nine foreign gassy mines, and the seven in the United States were documented in as much detail as possible. All this information is presented, along with appropriate conclusions and appendices. The study took two years and three months to complete.

Jan 1, 1983