Search Documents

By James H. Cobbs

Blind boring of shafts is becoming an increasingly important part of shaft sinking. Blind-bored shafts have reached diameters of 25 It in Europe and 16-1/2 ft in the United States. Much of the technology developed for blind boring has evolved from the technology of drilling wells for oil and gas production. Blind boring offers economic advantage in a number of situations where conventional shaft sinking either is extremely difficult or very expensive by virtue of large-capacity aquifers which must be penetrated, unstable ground or where very rapid sinking is required. In sedimentary rocks, blind boring is cost competitive with conventional sinking, in diameters of about 12 ft or less. Blind boring is not competitive with raise boring where conditions are favourable for raise boring. Blind boring does, however, offer greater flexibility than raise boring and can be performed in situations where raise boring is inefficient or impossible. Combination machinery has been developed to perform both blind boring and raise boring, so that the machine can be used effectively in situations where only the near-surface portions of the shaft are unfavourable for raise boring. Development work is being supported by the United States Bureau of Mines for blind boring equipment capable of boring shafts up to 30 feet in diameter.

Jan 1, 1979

Current AG and SAG mill circuits have continued the trend to larger, fewer mills. These large mills place a significant additional load on the discharge systems and it has become imperative that the designs of these mill discharge systems are evaluated carefully to ensure maximum efficiency and have the capacity to be able to handle the increased mill discharge volumes. The current generation of multiphysics modeling tools allow a detailed analysis of AG and SAG mill discharge performance. The combination of Discrete Element Method modeling and Computational Fluid Dynamics allows the designer to model in detail all aspects of a mill discharge performance. This includes a detailed description of the build-up of solids and slurry in a mill discharge, the recycle of material back into the mill through the grates, the relative wear rates and the occurrence of overloading at the pinch points. These tools allow intelligent decisions to be made regarding the type of discharge arrangement, pan lifter geometry, and discharge cone design, so as to ensure that the discharge is capable of handling the duties required for a specific installation. This paper details the current state of the art in these modeling tools, and provides an overview of some recent applications.

Jan 1, 2012

By William Winsor, Harold L. Snyder

"AbstractShould oil and gas be proven in commercial quantities on the Labrador Shelf, current technology is not adequate for production operations in this severe environment, which includes yearly invasion of pack ice and icebergs. The fishery of this section of the North Atlantic is a vital resource to which a major oil spill or blow-out would impose an intolerable burden, This means that production systems must be designed and built to be fail-safe.The experiences of mining in Bell Island and Cape Breton have shown that it is possible to operate beneath the ocean floor, and this technology may hold the key for safe, reliable and economic production, This paper attempts to define particular problems and outline possible solutions.IntroductionOUR DISCUSSION is subject to the assumption that large hydrocarbon reservoirs will be discovered in the sedimentary basin of the Labrador continental margin. The petroleum industry has not attempted to operate in a harsher area. The Labrador coastline is exposed to North Atlantic storms and icebergs year’round, Arctic pack ice occurs up to six months of each year. However, there is no doubt that, if sufficient hydrocarbon potential is outlined, development will proceed."

Jan 1, 1977

By R. L. Bruening, N. E. Izatt, S. R. Izatt

"Rare earth elements (REE) are essential and unique components of many high-technology products without which functioning of modern society would be greatly impaired. Commercial deposits of REE are limited to a few geographical locations. Largely untapped sources of REE are available in endof- life (EOL) magnets, rechargeable batteries, and electronics. Presently, < 1% of REE in EOL wastes is recycled. Conversion of EOL wastes to liquid streams allows use of IBC’s Molecular Recognition Technology (MRT) process to selectively recover, separate, and purify target REE and associated metals at g/L to mg/L or lower concentration levels. The MRT process together with its applications to separations of REE and associated metals in recycling as well as in mining are described. Economic and environmental advantages of MRT are presented. INTRODUCTIONRare earth elements (REE) include the lanthanide series (La-Lu), Y, and Sc. These elements are not rare, but concentrated minable deposits are scarce (Cordier 2012; Haxel, Hedrick, & Orris, 2002). Over 95 % of the world’s supply of REE is controlled by China (Hanson, 2011a) where they are mined, processed, and the pure elements incorporated into a growing number of consumer and military products. The consumer products are marketed worldwide. Since REE are vitally important in consumer and military products, this situation has caused other nations to scramble to develop the capability to produce their own supply (Cordier, 2012).In the U. S., Molycorp has reopened the Mountain Pass REE mine in California and production has begun (Goldenberg, 2010). Development of a reliable internal source of REE is of high national priority in the U.S. (Hanson, 2011b; Hess, 2012: “Obama Announces”, 2012). These elements have in recent decades been incorporated into new consumer and military products that are essential to our economy and defense. These products range from wind turbines, high performance magnets, hybrid car rechargeable batteries, energy efficient lighting electronics, flat screen televisions, and smart phones to advanced weapons systems (Haxel et al., 2002; Levkowitz & Beauchamp-Mustafaga, 2010)."

Jan 1, 2012

By I-H. Jung, J. Kim, B. Konar

"The usage of FeNdB permanent magnet, containing Rare earth elements (REEs), is steeply increasing with its demand for wind-turbine and electrical vehicle. The improvement and recycling of the permanent magnet require good understanding of chemistry of all constituent elements. In order to understand the chemical interactions between REEs and Fe, all Fe-RE binary systems have been critically assessed and optimized based on reliable literature data. The Modified Quasichemical Model and Compound energy formalism is employed to model the liquid phase and the solid solutions present in the binary systems respectively. The enthalpy of the liquid and the intermetallic phases showed a systematic trend along the lanthanide series. This helped to mitigate the discrepancies in literature data and also to predict the binary interactions between some less well investigated Fe-RE binary systems. INTRODUCTIONRare Earth elements (REEs) are a group of seventeen elements (including Scandium, Yttrium and the lanthanide series) that exhibit same characteristic chemical and physical properties. These properties make them valuable to the electronic, appliance, green technology, weapon and medical device manufacturing industries. Compounds of REE with other metals (like Co, Fe, Ni etc.) have unique properties of luminescence, thermal and electrical conductivity, magnetism and ability to act as catalysts and polishing compounds (Gschneidner ,2011).They are not only indispensable for some electronic gadgets of today, like computers, music systems, mobile devices, televisions and MRI machines, but also holds a key to more greener technology of the future. They contribute to the development of more efficient and environment friendly version of everyday products such as cars and light bulbs. REE compounds revolutionized the magnet industry by making them smaller and more powerful with increased longevity, and high temperature workability, which are used in motors and generators that power electronics, telecommunications, electric automobiles and turbines(Humphries, 2011)."

Jan 1, 2012

By Edward S. Bell, Frank Angebrandt

"Nuclear reactors must have very large heat outputs to compete with conventional sources and the only feasible applications are in the production of electric power or large quantities of process steam. This paper considers alternative fuels for electric power generation in Canada. In a publicly owned utility, nuclear stations are economic for base-load generation for unit sizes of 500 mega• watts or larger where competitive fossil fuel costs are higher than about 30 cents per million Btu. In British Columbia, Alberta and Saskatchewan, fossil fuels will continue to be in adequate supply at costs lower than 30 cents per million Btu and thus, except for the special case of Vancouver Island, power generation in Western Canada will continue to be the hydraulic and conventional thermal type. In Eastern Canada, fossil fuel prices are likely to be higher than 30 cents per million Btu and most utilities will be able to install units of 500 mw or larger, so that nuclear power plants will provide much of the base-load generation required. Base-load generation comprises about two-thirds of the energy generated by power utilities. By 1990, the total annual electrical energy load will be over 600 billion kwh, with two-thirds of this load in Eastern Canada. Allowing for additional hydraulic resources which may be developed in Quebec, British Columbia and Manitoba, hydraulic generation is forecast to provide a little more than a third of this electrical energy, nuclear generation a third and fossil-fuelled generation about a quarter."

Jan 1, 1969

By V. Aitken

Line-of-sight radio control has received widespread acceptance for use in many mining methods because today’s technology offers improved economics and personnel safety. Significant advances in higher autonomy for mining machines are not currently seeing widespread use even though they offer great future potential. With autonomous capabilities being a longer-term goal, a logical sequence of advances based on TeleRemote control is proposed. Under Tele - Remote control, the operator is in direct control of the machine at all times. Three levels of Tele - Remote control systems are presented including line-of-sight, extended line-of-sight, and full load-haul-dump applications. Distributed control and sensing subsystems arranged in a vehicle control area network support incremental system expansion through the three levels of TeleRemote control and prepare the machine for integration of higher levels of automation as mature technology becomes available. This approach allows full exploitation of today’s mining automation technology with a flexible future growth path.

Jan 1, 1998

By T. Holmes, S. Davison

"A surge bin at Agrium’s Vanscoy potash operations has been plagued with flow, wear, and corrosion issues since being built in 1967. The culprits? The bin’s carbon-steel construction, geometry, and the resultant funnel-flow pattern are the root causes. An investigation and cost analysis indicated that hopper redesign and retrofit would increase production and reduce maintenance and capital costs. The retrofitted bin provides safer, more reliable operation and has a much longer predicted working life. Using this example, the authors describe bulk-solids-flow theory and highlight the importance of customizing bulk-material-handling-system design using appropriate flow properties to improve reliability, safety, and cost effectiveness.RÉSUMÉ Depuis sa construction en 1967, un réservoir intermédiaire de l’exploitation de potasse Vanscoy d’Agrium connaît des problèmes de débit, d’usure et de corrosion. Les responsables ? La construction en acier ordinaire du réservoir, sa géométrie et la structure de débit en résultant au niveau de la carotte en sont les causes fondamentales. Une étude et une analyse des coûts indiquaient que la restructuration et la rénovation de la trémie permettraient d’augmenter la production et de réduire les coûts d’entretien et en capital. Un réservoir rénové permet de renforcer la sécurité ainsi que la fiabilité de l’exploitation, et sa durée d’activité prévue en est augmentée. En se fondant sur cet exemple, les auteurs de l’article décrivent la théorie du débit de matières solides en vrac et insistent sur l’importance de personnaliser la conception du système de manutention des matériaux en vrac à l’aide de propriétés rhéologiques adaptées afin d’améliorer la fiabilité, la sûreté et la rentabilité.INTRODUCTIONIn early 2013, Agrium’s Vanscoy Potash Operations (VPO) engaged Jenike & Johanson Ltd. (J&J) to provide testing, consulting, and structural engineering services related to proposed modifications to the 270 t special standard product surge bin, which Agrium planned to undertake during a two-week shutdown in August 2013. The bin, which had been plagued with flow, wear, and corrosion issues for its entire working life, was essential for the continuous operation of two of VPO’s compaction plants and for efficient dispatching to loadout. The bin often experienced product hang-ups, clumping on the walls, and plugging at the hopper outlet. Two recent unscheduled mill shutdowns had been partially attributed to flow issues in the bin due to clumping and product plugging up at the screws. These problems increased maintenance costs, limited production capacity, and degraded product quality. Holes and paper-thin sections in the bin walls discovered during a 2013 inspection revealed the potential for major hot material leaks or even structural failure. Either issue would stop plant operations until the bin could be repaired or bypassed. Clearly, the bin cone had reached the end of its life and required replacement."

Jan 1, 2018

By Jesús L. Valenzuela, José R. Parga, Salvador Aguayo, Héctor Moreno

The Merrill Crowe zinc-precipitation process has been applied worldwide on a large number of operations for the recovery of gold and silver resulting in a higher consumption of zinc dust from cyanide solutions. However, in some of plants this precipitate is of low quality, because lead, cadmium and especially copper are precipitated along with gold and silver. The low quality precipitate also requires more fluxes in smelting and shortens crucible life. In this study, a process is introduced to remove copper, silver, lead and cadmium from barren solutions following the Merrill-Crowe process. Copper and silver are removed by precipitation in a serpentine reactor, using sodium sulfide as the precipitator, and sulfuric acid for pH control. The recovery of lead and cadmium ions with natural hydroxyapatite using cow bone powder (CBP) as a new adsorbent material, is introduced. CBP is capable of removing lead and cadmium ions from aqueous cyanide solutions with 99% efficiency. It has the ability to compete with other existing commercial adsorbents for the removal of lead and cadmium. Results show that pH value has a significant effect on copper cyanide removal efficiency, and it was determined the optimal pH range to be 2 - 3. At this pH value, the copper cyanide removal efficiency achieved was up to 99 %; and for the cyanide associated with copper cyanide complexes, the recovery was 90%. Finally, the precipitate quality was improved 400% .This procedure was successfully run at three mines in México.

Jan 1, 2014

By A. Galley, R. Tosdal, F. Robert

The Canada Mining Innovation Council (CMIC) Exploration Innovation Consortium developed a 10-year business case for developing new discovery criteria, exploration techniques, and better data management and analysis to improve exploration success in deep, remote, and covered terrains. Within this context, the CMIC devised a five-year project proposal to create improved multiparameter exploration tools to detect ore systems and more efficient vectoring toward high-grade mineralized cores. The Footprints project was approved March 2013. More than CAD$13 million funding was provided through the CMIC-led joint sponsorship from 30 companies and the Natural Sciences and Engineering Research Council. Consistent industry leadership and integration of dedicated industry and academic expertise has the project on track for reaching its well-defined objectives.

Jan 1, 2014

By L. K. Smith, C. R. May, K. R. Schrag, H. Buchwald

"New contracts for 65 million long tons of coking coal valued at over $900 million, over the next 15 years, herald the rebirth of Alberta's coal industry. The industry is optimistic that export orders may reach 20 million tons per annum by the mid-1970's. Coal will be extracted from underground and surface mines and it is expected that the total labour force will double from the present 1,200 men within the next two years. Ali the health hazards associated with coal mining are likely to be encountered and it will be incombent on the Provincial Department of Health to specify the standards which relate to health and environment where no such standards have previously existed. This paper examines some of the problems which are being encountered in setting up an environmental health program and reviews the practicability of environmental monitoring methods, with special reference to respirable dust."

Jan 1, 1969

By J. K. Weglo, M. U. Savich

"The measurement and evaluation of the noise emanating from an ST4A scooptram in an underground stope under a simulated work cycle, and under three conditions of after-treatment systems is covered.These include scooptram without muffler or filler (bare engine), an in-line small filter, compared to a larger-filter, and the larger filter with an in-line muffler in series with fume diluter, which were tested under three engine operating conditions-IDLE, wide open throttle (W. 0. T.), and working condition. This is load, short haul and dump operation.The results showed an attenuation of the scooptram at work of 8 to 15 dBA, 16 cm from the exhaust pipe of the machine, to 4.8 dBA at the operator&apos;s ear. Recommendations are made to increase the attenuation at the operator &apos;s ear by additional improvement in design of the fume diluter.IntroductionIn current mining operations, the diesel engine provides a safe, efficient and highly mobile source of power. In the major underground mine s in Canada the most common types of diesel equipment are load-haul-dump (LHD) machines and ore trucks. In general, there is a tendency to use high horsepower, diesel LHD machines in mines to achieve maximum productivity. The increased use of diesel-powered equipment in underground mines has shown no cause pressure levels were measured at the exhaust and outlet pipe. Also, while measuring the octave band and A-weighted sound pressure levels, the operator&apos;s position was also measured."

Jan 1, 1986

By V. T. Panayotov, M. I. Panayotova

Wastewater from mining and mineral processing activities is often polluted by anion forming metals, such as molybdenum and chromium. Low cost materials, including zeolites, are studied for removing heavy metals from wastewater. It is widely accepted that natural zeolites are not effective in removing metals in anionic form. The paper presents study on use of metal modified natural clinoptilolite to remove Mo (VI) and Cr (VI) ions from model soft wastewater. Modification with Pb, Fe(III), Zn and Ba increases clinoptilolite uptake capacity with respect to Mo(VI) at low pH values of the water subjected to treatment, the efficiency decreasing in the order Pb > Fe(III) > Zn > Ba. Only lead-modified clinoptilolite shows high uptake of Mo(VI) in acidic, neutral and slightly alkaline conditions. Modification with Pb, Ba and Fe(III) increases zeolite uptake capacity with respect to Cr(VI) from neutral water. The effectiveness of Ba-modified zeolite decreases in slightly acidic water. Over 90 % uptake of initially available Cr(VI) is achieved by lead-modified clinoptilolite both under neutral and slightly acidic conditions. Increasing the initial pollutant concentrations increases the removed amount both of Cr(VI) and Mo(VI) for Pb-modified clinoptilolite. The findings could be a basis for using the natural clinoptilolite to remove in consecutive steps: firstly Pb(II) and/or Fe(III) ions and then loaded zeolite to be used for Mo (VI) and/or Cr(VI) removal. The kinetics of Mo(VI) uptake by CL-Ba, CL-Fe(III), CL-Pb, and CL-Zn is best described by the pseudo-first order kinetic equation. The kinetics of Cr(VI) removal by CL-Ba, CL-Fe (II), CL-Fe (III) and CL-Zn is best described by the pseudo-first order kinetic equation. Kinetics of Cr(VI) removal by CL-Pb obeys the equation for the first order irreversible reactions. Finding way to remove anions-pollutants from the mineral processing wastewater will render this industry more environmentally friendly and socially acceptable.

Jan 1, 2016

By C. Hudson, D. Tremblay, A. Frey

"A discussion of the design, challenges and successes associated with the commissioning of the gravity recovery circuit at Canada’s newest open pit gold mine - Atlantic Gold’s Moose River Consolidated Project in Nova Scotia, Canada is presented. An overview of the project, its historical significance and overall flowsheet is provided with special focus given to the design and selection of the gravity circuit equipment including the scalping screen, gravity concentrators and the novel intensive leaching technology selected for the project. The performance of the gravity circuit is benchmarked against the feasibility study process design specifications and the outcomes are discussed. Challenges encountered during commissioning are also presented, including the use of third-party automation and the effects of screen sizing on overall gravity circuit performance. Mechanical modifications made to the Sepro Leach Reactor for the Moose River project are also discussed. A detailed technical review of the mechanical and operational aspects of the Sepro Leach Reactor is provided with key operational data on leach times, recoveries, reagent usage, solid-liquid separation, pregnant solution quality and its influence on bullion purity.INTRODUCTION Atlantic Gold Corporation’s Moose River Touquoy Mill in Nova Scotia, Canada was commissioned in the fourth quarter of 2017 with commercial production declared in March of 2018. The 2 Mtpa process plant uses a conventional, gravity-CIL process. This site was previously mined in the 1870s. Interest waned in the early 1900s but resumed in the 1930s and the mine was brought back into production in 1935 until an underground mine collapse in 1936. This mining district became famous after CRBC radio commenced a ground breaking, around the clock, broadcast of the rescue operations. Over 100 million people listened to the broadcast from Canada, the United States and the United Kingdom. These broadcasts changed radio, transforming it from a medium for music to on the spot, breaking news reporting. The mill was constructed by Ausenco on a fixed price EPC contract in the historic Moose River gold mining district, 95 km north-east of Halifax by road. The mill will process ore from the adjacent Touquoy pit for the first 5+ years of operation; after the Touquoy reserves are exhausted, the mill will process ore trucked 37 km from the Beaver Dam deposit for an additional 5 years."

Jan 1, 2019

By Ramón Alanís, Filiberto Orrante, Andrea Festa, Baldomero Gutiérrez, Fernando Cornejo

"SGS implemented two rules-based fuzzy logic expert applications on two grinding circuits operated by Peñoles Group in Mexico. Both expert systems are based on control strategies that push against process constraints to improve throughput. Based on proven methodologies, the projects also required some new approaches that led to permanent changes to the mill control strategy.This paper provides descriptions of the implementation, operation and performance of both expert systems. It also reviews how improved production rates were achieved through the use of a common set of expert technology tools. An overview of the resulting control strategies implemented on the two circuits is presented. The paper also discusses the identification of the process constraints within each circuit and how these constraints are used within the expert systems.INTRODUCTIONMexico-based mining company Peñoles Group and the Advanced Systems group at SGS, formally known as MinnovEX Technologies Inc., collaborated on the implementation of two expert systems in two grinding plants, both located in Northern Mexico.The primary objective of the expert systems was to increase throughput whilst still maintaining the cyclone overflow product size within an acceptable range. The secondary objective was to achieve a high level of utilisation of the expert technology.In order to achieve these objectives, SGS proposed a proven methodology which leveraged the existing operating and technical expertise at site through the client’s involvement in the design and implementation stages. The in-house operating and technical expertise of SGS was also brought to the project and implemented with the client’s approval at all stages. At both sites the final acceptance was defined upon meeting both process and utilization parameters.The development and deployment of rules-based fuzzy logic applications has matured as a technology and consequently, clear definition of process states and their place in the logic structure to control a given circuit are now transferable. The key to the robustness of the control logic depends on selection and tuning rules for maintaining stability and optimizing a given circuit. Application integrators need to have a standardized approach for timely integration and deployment; a critical component to avoid the common critiques that expert applications are idiosyncratic and difficult to maintain."

Jan 1, 2009

By Marvin E. Lane

Viburnum, located in the foothills of the Ozarks in south-east Missouri, is the site of a modern lead mining and milling operation. Two mines are currently producing a total of 5,000 tons per day and a third mine is in the final development stage, with full production scheduled for late this year (1964). These mines will supply the tonnage required to keep the Viburnum mill operating at a full capacity of 7,000 tons per day for many years. The efficient underground mining operation is completely trackless. Drill jumbos are used to break the ore in a room and pillar method of mining. Transloaders, or St. Joe shovels, and trucks do the loading and hauling. The Viburnum mill has a world-wide reputation as a most efficient operation. This is due to the extensive use of automatic process controls, and labour saving materials handling facilities. Introduction THE St. Joseph Lead Co., has operated lead mines in southeast Missouri for 100 years. These operations have been confined largely to the area called the

Jan 1, 1964

By Graham Holmes, John Starkey

"The Kinross Kubaka Project is a gold mine located in the Russian Far East. The grinding circuit, comprised of a 6.1 m diameter x 2.74 m long SAG mill and a 4.1 m diameter x 5.5 m long secondary ball mill in closed circuit with cyclones, was built using SAG Power Index and Bond Ball Mill Work Index testing to determine the grinding energy requirements. Extremely cold climatic conditions and the need to keep heated space and capital costs to a minimum, dictated a grinding circuit with no in-circuit crusher and no conveyors external to the mill. High energy requirements for both the SAG mill and the ball mill were correctly predicted and have allowed grinding production tonnage forecasts to be met. Design test data and production results are given.INTRODUCTIONIn 1995 Davy International Canada, now Kvaerner Metals E & C, was commissioned as the Engineer and Project Manager for the Omolon Gold Mining Company, to design and construct a gold extraction plant for the Kubaka gold deposit, located in the Russian Far East. This deposit had been studied extensively in Russia during the exploration phase and a Feasibility Study was completed in 1993 by Kilborn who visited the site twice during that year to inspect facilities and to take metallurgical test samples. More samples were taken in 1995 to check ore hardness variability, as part of the final design program by Davy.The client’s objective in designing the Kubaka grinding circuit was to achieve design tonnage at all times, even when milling the hardest ore zones in the deposit. Since the samples taken in 1993 were taken as composite samples, it was necessary to take additional samples in 1995 to determine the extent of the variability. Six samples were sent to Canada for SAG Power Index (SPI) testing. Five of these were combined as a composite open pit sample, while the sixth sample was taken from the site adits as a composite sample to represent undergound ore. These two composite samples were tested to determine the MacPherson Autogenous Work Index for comparison with the SPI values."

Jan 1, 2001

By P. Kordi, L. Egorova, R. J. Bowell, D. Gurevich, V. Sedov, A. Mikhailov, D. A. Holwell

ABSTRACT Reconnaissance exploration in the Kuene region Namibia has included geological mapping, soil and stream sediment geochemistry, and ground geophysical methods. Copper mineralization occurs within a well-defined belt with north-northwest to south-southeast trend, parallel to the regional strike of the sedimentary rocks. The occurrences vary in size but are generally stratabound. The mineralization is centred on the transition from calcareous shale and interbedded limestone, through carbonate rocks, to quartzite. Geochemical anomalies have been identified correlating to induced polarization (IP) and magnetic anomalies. The anomalies identify one potential metallogenic zone more than 17 km in strike length.

Jan 1, 2012

By I. Ciabatti

Inorganic salts of hexavalent iron (ferrate (VI)) are versatile reagents for water and industrial effluent treatment because of the strong oxidising effect of the ferrate ion (FeO42-) and the well-known coagulation properties of the resulting ferric ion. Among other applications, ferrate can effectively remove arsenic, cyanide and phenols from industrial effluents. Furthermore, ferrate salts can be prepared from ferrous sulphate, a common byproduct of the steel and titanium industries, and possibly from other iron wastes. Notwithstanding their many potential advantages, the industrial-scale application of ferrate salts, such as potassium ferrate (K2FeO4), for effluent treatment has been hindered by the difficulties inherent in their synthesis and stabilisation. Within a project co-funded by the European Commission, the large-scale synthesis of stabilised potassium ferrate was realised through a new synthesis process, and different applications of the resulting ferrate to effluent and wastewater treatment are under investigation. This paper reports the results of the application of stabilised potassium ferrate for the purification of textile effluents. Laboratory and pilot-scale tests were carried out and the performance of the ferrate was compared to that of chemicals currently used in wastewater treatment. According to these experiments, potassium ferrate is a promising reagent for an effective treatment of textile and other industrial effluents.

Jan 1, 2006

By F. H. Edmunds

I N presenting this paper, the writer wishes to point out some of the difficulties and problems of geological work in that part of Saskatchewan in which outcrops are few. These problems are well known to all geologists who have made investigations in this region, but may not be so well known to those outside. A table of the strata as known in certain areas of Saskatchewan and the adjacent provinces is given, with a brief discussion of some of the formations and beds about which there is little knowledge due to their being deeply buried and not exposed in the region. Comment with regard to possible oil and gas structures is made and some features of the structures in the Battleford and Simpson districts are described. The writer wishes to make acknowledgment to members of the Geological Survey of Canada to whose work in Saskatchewan and the adjacent provinces reference is made, and to others who have made, or are making, valuable contributions to the stratigraphy of Saskatchewan. Mr. G. C. Webb has kindly furnished information regarding and materials taken from a well bored recently in the Paynton district. Special thanks are due to the Simpson Oil and Gas Company for permission to use much valuable information with regard to their wells and for the generous way in which the officials and staff co-operated with the writer. The opportunities the writer has had to visit many parts of the Province have been in connection with investigations for the Provincial Department of Natural Resources and through facilities provided by the Department of Soils of the University of Saskatchewan. To these Departments the writer accords his thanks. For the purposes of this discussion, Central Saskatchewan may be considered as that portion of the Province extending from Township 16, with Regina, Moose Jaw, and Swift Current situated on or near the southern boundary, to Township 48, with Prince Albert and Lloydminster on the northern boundary. This region includes territory underlain by Cretaceous sediments and excludes the southern portion of the Province, where Tertiary beds underlie the surface and are exposed to an extent sufficient to permit a measure of systematic mapping.

Jan 1, 1937