Search Documents

By Luke Meers

Roadway development rates in Australian underground coal mines are failing to keep pace with modern longwall systems and are unlikely to sustain further improvements in longwall productivity into the future unless step change improvements to roadway development equipment and practices are made. Bottlenecks which limit and constrain improved production and impact the safety of operators have been identified through a series of industry surveys, with the manual installation of strata support materials, consumables delivery, coal haulage and monorail installation being highlighted as major areas to improve development performance. This paper looks at research being carried out at the University of Wollongong in designing an integrated system approach for the fully automated handling and installing of development consumables, and the systems required to support these activities. A series of hard automation manipulation devices have been demonstrated in surface trials and the results indicate that rapid roadway development can be achieved.

Aug 1, 2013

By W. Gordon Muir

This paper deals with the exploration, development and current operations of the salt mine at Goderich, Ontario operated by the Sifto Salt Division of Domtar Chemical Limited. The rock salt is obtained from a bed 1,760 feet below the surface, 75 feet thick, extending under Lake Huron. Annual production is in excess of one million tons. Large mobile equipment is used. Details of this equipment, as well as the shaft layout, which permits the equipment to be lowered underground with a minimum of trouble are outlined. Mining, crushing and screening procedures' are rev1ewed. Reference is also made to productivity salt distribution and uses.

Jan 1, 1967

By C. Liu

Corrosion behavior of the stir zone in a friction stir weld of dissimilar A12024/AZ31 alloys was investigated in the immersion test in distilled water (pH=6) for different times. Microstructures and the distribution of chemical elements were analyzed by scanning electron microscopy (SEM) and energy dispersive X-ray spectroscopy (EDS). Due to the difference in the corrosion potentials between A12024 and AZ31, the AZ31 alloy constituent in the stir zone was susceptible to the corrosion attack in the distilled water. The corrosion attack was found to occur in the narrow region of the AZ31 alloy adjoining the A12024 region, where there was a low ratio of anode-to-cathode surface area. The corrosion attack became more severe in the AZ31 alloy regions with increasing immersion time. The A12024 alloy region in the stir zone of the weld was protected by cathodic reactivity due to sacrificial anode AZ31 alloy.

Jan 1, 2007

By Norman R. Ball

"Many people in the mining and metallurgical industries were brought up to embrace Henry Ford's pronouncement that ""History is bunk"" but it is not generally known that the same Henry Ford created and paid for one of the finest technological museums in the Western World. I am aware that many people feel that industry history is something you ask aging executives to do or that history is a clip-andpaste compendium of pictures re-discovered every 25 years or on the occasion of issuing a press release on plant expansion. Moreover, there are many who fear historians as somewhat deranged individuals interested only in corruption, injustice and sensational labour strife. Good history lies somewhere between the controlled P.R. handout and the hysterical attack. Writing good history is a difficult creative act based on the application of experience, insight, wide knowledge and careful reasoning to available evidence. To date, the Canadian mining and metallurgical industries have achieved a great deal but left too little evidence and it is this lack of evidence which must be corrected before it is too late. It is the purpose of this article to stimulate thoughts with regard to archives, one of the more important vehicles for the preservation of such evidence."

Jan 1, 1999

By A. J. Baer

"DEFINITION OF THE REGION AND ITS BOUNDARIESTHE EXPOSED PART OF THE GRENVILLE PROVINCE is the southeastern part of the Canadian Shield, characterized by crystalline rocks with K-Ar ages of about 1,000 million years. Its Canadian portion is bounded on the southwest by Georgian Bay •and by Paleozoic sediments south of a line passing through Orillia and Kingston, on the southeast by the St. Lawrence River valley and the north shore of the Gulf of the St. Lawrence, on the east by the coast of Labrador and on the northwest by the Grenville front, a linear tec-tonic feature that is a metamorphic transition zone and/or a fault. Rocks located to the southeast of the front have younger K-Ar radiom€tric ages than rocks located to the northwest of it.The region is formed of complexly deformed and highly metamorphosed crystalline rocks and in part differs from other areas of the Canadian Shield by the presence of large amounts of crystalline limestone and bodies of anorthosite."

Jan 1, 1970

By G. Song

This paper reports the anodizing voltage, gas evolution and sparking behaviors of an anodized coating formed on AZ91D in a silicate containing solution. According to their responses to an anodizing current, a four-stage anodizing mechanism is proposed. At the same time, the formed coating is characterized in terms of its microstructure, composition, thickness and corrosion performance. It was found that deposition of MgSiO3, Mg(OH)2 and MgO as well as dehydration of Mg(OH)2 are involved in the anodising process; the vigorous gas evolution accompanied by intensive sparking and the corresponding negative anodising efficiency in the later stage of the anodising process are closely associated with thermal decomposition of water due to the high temperature resulting from the intense sparking on the surface of the anodized alloy; the thickness, porosity, and composition of the anodised coating on a magnesium alloy depend on the final anodising cell voltage; and the corrosion resistance of a thick but porous coating containing more silicates appears to be more corrosion resistant than a thin but compact coating containing less silicates.

Jan 1, 2006

By S. A. Bradford

The twenty years before World War I was the Golden Age of copper smelting in British Columbia. In this short time, the smelters developed from small, primitive units to large, efficient operations. The first copper claims had been staked on Howe Sound and Knight Inlet in 1864, and there was extensive copper mining in the interior by the mid-1880s, but before 1895, all ore was shipped out of the country for smelting, converting and refining. The first interest in smelter construction was undoubtedly inspired by a Provincial bonus and Dominion land grants offered to smelter builders. The early smelters made use of small blast furnaces which were designed to smelt any kind of ore, but usually far too little ore was available. The first smelter seems to have been the McRae furnace on the Spillimacheen River (1883), followed by Vancouver (1889), Revelstoke (1891), and Golden (1891) (1). They each smelted a few tons of galena and then quickly closed down permanently for lack of ore. Only smelters that actually produced some copper matte are described in the following sections.

Jan 1, 1999

By T. H. Wilson

In 1901, the Crow's Nest Pass Coal Company, Limited, began producing industrial coke in 212 beehive ovens at Michel colliery. By 1908, 486 ovens had been installed and in that year 147,623 tons of coke were produced. Coke manufacture has been continuous from 1901 until the present time (1946), with total production of 2,795,402 tons. At present writing, only 100 beehive ovens are operating and production is reduced to 1,800 tons per month, due to the shortage of suitable labour. These ovens are drawn by hand, on contract, and the workmen are exposed to considerable heat. A man draws three ovens in eight hours, thereby producing approximately 1072 tons of coke per day. In addition to the inefficient and costly method of drawing coke in beehive ovens, tremendous losses are experienced in the wastage of gas and tar, which are driven off into the atmosphere. Also, the yield of coke per ton of coal fed to the ovens is low as part 9f the carbon is utilized in producing heat to carbonize the remainder of the coal. A recovery of only 55 per cent of the carbon, as coke, is obtained. The coking process takes place from the top of the charge, which is 21/2 feet deep, downward to the floor. Six and a half tons of coal are charged and 3.6 tons of coke are drawn from the oven after 72 hours' carbonization. The beehive ovens using Michel coal produce a very hard and tough coke, large in size and of silvery appearance, which has served the requirements of both foundry and smelter for many years. In 1938, the Company made a careful study of coking processes with a view to introducing a more economical method than beehive ovens and one that would be less dependent on skilled labour, the supply of which was rapidly diminishing at that time. Various methods of by-product coking were investigated, and it was decided that the Curran-Knowles process offered the greatest possibilities because of the low capital investment in relation to output and also because the horizontal oven design was suitable for an expanding coal. Consequently, a test on Michel B seam coal, supervised by Mr. E. Burrough, of the Fuel Research Department, Ottawa, was run in the Curran-Knowles plant at West Frankfurt, III. The results of this test led to the construction of a ten-oven battery of 32 ft. 6 in. by 8 ft. 3 in. Curran-Knowles ovens at Michel, which were completed in November, 1939. This battery was built as an experimental unit, with provision for an additional ten ovens if the coke proved satisfactory for the market. In 1942, an expanding coke market led to the construction of a second battery of ten ovens, which were completed in April, 1943.

Jan 1, 1947

By A. R. MacLean

This mine is situated at Point Aconi, Cape Breton , Nova Scotia, and is a replacement for the 100-year-old Princess Collie ry. It is a slope mine which is the continuation of a s trip mine operation. There are fives lopes from the surface driven with Dosco Dintheaders - this marks the first time these machines were used in North America. There are four room -and-pillar sections, each equipped with a Lee Norse HH106 continuous miner, a "Top Dog" roof bolter and two Wagner diesel Teletrams. There are also two Eimco 913 diesel LHD's , which are used for clean-up in the mines. This paper describes the mining operations of this 800,000-tpy mine which, in less than a year and a half , has been developed to the stage where four sections are producing coal at the desired rate.

Jan 1, 1978

By Roger Francis

There is increasing use of acid leach extraction methods at elevated temperatures and pressures by the mining industry. In many locations there are limited supplies of fresh water, and waters with higher chloride contents must be used, making conditions more corrosive. The fluids downstream of the main autoclave are hot, acidic, oxidizing and contain chlorides and present a challenge to the mining community to ensure reliable operation. Zeron 100 is a high strength superduplex stainless stee, that offers high corrosion resistance at a cost effective price. The paper presents a combination of laboratory data and service experience, particularly in the aggressive fluids found in downstream processing.

Jan 1, 2010

By T. Scully

Since early days in coal mining, it has been known that some coals and the carbonaceous materials associated with them will heat and fire spontaneously. Many theories have been advanced to account for this phenomenon, but it is only within comparatively recent years that any scientific research has been carried out to determine the causes of this heating, the conditions which bring about its occurrence, and the reason why different coals heat with a varying degree of readiness. So far, this research has not cleared up these points entirely, but a great advance has been made in our knowledge of the matter. In general, any coal will fire spontaneously, although with a varying degree of readiness, provided conditions for its doing so are favourable enough. These conditions are that the coal must be in a fine state of division, that sufficient oxygen must be present for rapid oxidation, and that the air current passing must be so small that it is insufficient to carry off the heat produced by this oxidation. Many other minor factors, however, contribute to bring about spontaneous heating, either by producing initial heat themselves or by inducing the other major conditions.

Jan 1, 1931

By Hong-wei Ma

With social development and technological advancement, mine rescue robots used in complex environments have developed as a research hotspot. This paper reviews the progress of research on coal mine rescue robots, and key technologies of rescue robot design are put forward, such as mechanical structure, self-navigation and self-orientation, multi-sensor information fusion, multi-robot cooperation, and wireless communication technology.

Aug 1, 2013

By Yuyong Li, Liangman Zhang, Zhaolian Wang, Shun Wang, Ltd. Shandong Huate Magnet Technology Co., Fengliang Liu

"Introduce a newly revolutionary magnetic separator - Raising Concentrate Grade and Decreasing Dregs Content Magnetic Separator Series JCTN (i.e. RCG&DDC MS JCTN). HUATE® JCTN is designed for rinsing, purification, desliming and thickening of the magnetic minerals as per different requirements. Adopting 240°-270° larger magnetic element with multi-poles and magnetic pulsation, and combining the devices of multi-channel rinsing water and top flushing water and new style tank, HUATE® JCTN can improve another 2%-10% concentrate mFe% than the traditional MS without lowering the concentrate recovery rate. Thereby, it solves the uneasy concentrate upgradation problem of the traditional MS resulting from the magnetic aggregation. Now, JCTN has been successfully applied in more than 30 mines in Australia, China and Russia, e.g. Sino Iron of CITIC PACIFIC MINING MANAGERMENT PTY LTD. HUATE® JCTN can optimize the industrial processing line by: 1) improving the discarding rate before milling to discard the necessary tailing ASAP; 2) getting in advance the final concentrate after milling. One JCTN can replace many traditional MS in series. In some way, it can also replace the anti-flotation separation process.INTRODUCTIONWe’re writing to introduce a newly revolutionary magnetic separator - Raising Concentrate Grade and Decreasing Dregs Content Magnetic Separator Series JCTN (i.e. RCG&DDC MS JCTN). HUATE® JCTN is designed for rinsing, purification, desliming and thickening of the magnetic minerals as per different requirements."

Jan 1, 2016

By Jos. Kalbhenn

PART of the plan of re-allocation evolved by the engineers of the Dominion Steel and Coal Corporation in 1932 to retard the rapid advance of the submarine workings seawards was the opening of Dominion No. 20 Colliery, in the Harbour seam, by a pair of cross-measure tunnels from the workings of an older mine working the Phelan seam, which lies 430 feet below the Harbour seam. The tunnels, 8 ft. by 13 ft. in size, were started away from the old workings of Dominion No. 2 at a point 1.5 miles beyond the shore line and were driven on a rising grade of 1 per cent for a distance of 5,335 feet, tapping the Harbour seam at a point 2 ¼ miles off-shore. For transportation and ventilation, shafts and roadways already existing in the Phelan seam were made use of during the stages of development and up to the present time. One of the two tunnels served as a main haulage road and an intake airway, and the other as a return airway and travelling road. However, as the workings of this new colliery expanded, the need for additional airways arose as was anticipated when the plans for the development were formulated. To meet this need, work was started on October 1st, 1942, to establish a new opening between Nos. 2 and 20 Collieries in the form of a vertical shaft to provide a passageway for the ventilating air current of some 250,000 cubic feet per minute on its return to the upcast shafts in No. 2 Colliery, thus making both tunnels available for intake airways. In the interest of safety, speed, and economy, the shaft was raised from the Phelan to the Harbour seam. It is 20 ft. by 12 ft. in size and, with the exception of three timbered compartments across the narrow end, is untimbered. One of the three timbered compartments housed the ventilating tubing and pipe lines, the centre one served as a cage-way for hoisting men and material during the operation of raising, and the third one contained a ladder way. The rest of the shaft was filled with debris during the period of shaft raising.

Jan 1, 1944

By John T. Ling

"This paper describes the operation of a rope haulage used as the main system of transportation in an underground coal mine. Prince Colliery, which is operated by the Cape Breton Development Corporation, has been in operation for 23 years and produces 1.2 million tonnes of coal annually. The mine extends a distance of 8000 metres under the Atlantic Ocean. All personnel and supplies are transported by means of an endless rope haulage system consisting of a train of rail cars that are operated by an electric engine on surface. The wire rope is 15 km long and weighs 63 tonnes. The system is believed to be the longest of its type used in an underground coal mine. The design of the system, safety features of the haulage, and problems encountered during the design and construction are described. IntroductionCoal has been mined commercially in Cape Breton, Nova Scotia since the 1800s. Several coal seams that are part of the Sydney coal fields, dip toward the north and northeast out under the Atlantic Ocean at angles between -4 and -15 degrees. Coal has been economically mined at depth in excess of 1200 m and more than 11 km from the coastline.Traditionally, single and double drum hoists have been used to haul the coal to the surface and also for transporting the workers and the materials required for mining up to 8 km. With the introduction of mechanized mining methods in the late 1960s, conveyor belts began to replace rope hoists for coal transportation. Improvements in hoisting system design also allowed for drums that could wind up to 6100 m of 32 mm wire rope in 15 layers.These hoists are commonly referred to as “drop hoists” because they take advantage of the gradient of the slope to assist in allowing the mine car train to reach the end of travel. The cars travel on steel rails and the rope is guided by rollers to reduce friction in the system."

Jan 1, 1999

By A. H. Lang

Introduction The recent uranium discovery at Theano point, lake Superior, is probably a rediscovery of the first reported Canadian uranium occurrence. A description of material from the original discovery was published in 1847 by J. L. LeConte, and many attempts have been made to relocate the deposit. Such attempts have in the past been unsuccessful because of vagueness in the original description of the locality. Besides being a prospect that seems to merit development work, the Camray discovery is important because it reaffirms the occurrence of pitchblende in the eastern part of the Precambrian shield. Much staking followed the announcement of the discovery, and some additional finds have been reported. Location The Camray discovery is at the shore of Theano point, lake Superior, about seventy miles north of Sault Ste. Marie (see Figure 1). It is in township 29, range XIV, district of Algoma. The showing is two miles from Highway No. 17, and is reached by a rough trail that leaves the highway at mileage 72.9 from Sault Ste. Marie. There are no towns of any size nearer than Sault Ste. Marie.

Jan 1, 1949

The methods employed for the addition of uranium to steels and cast iron in the Physical Metallurgy Division are outlined. It has been found that the segregation of? uranium is a major problem in aluminum and/or silicon killed steels and that the cooling rate is important in al-lowing the segregate to settle to one area, which can subsequently be discarded. The unsegregated areas were found to be extremely low in total oxygen, acid insoluble aluminum (AizOg) and, in some cases, slightly lower in nitrogen. Uranium recoveries, based on analyses of the unsegregated areas, were quite constant, at about 45 per cent, regardless of the type of uranium master alloy used for the addition. No segregation of carbon, manganese, silicon, sulphur, phosphorous, chromium or copper was observed in these steels. In commercial heats, the recoveries ranged from 7 to? 29 per cent for ladle additions to oxygen converted steel. When the steel was fully deoxidized prior to the uranium addition, recoveries ranged from 49 to 66 per cent, regardless of the steelmaking process.

Jan 1, 1964

By Robert D. Irvine

"Enhanced concern for protection of the environment and attendant actions by environ-mental regulatory authorities in support of this concern are influencing, to varying degrees, the demand and supply of a range of industrial minerals in a number of jurisdictions. These influences take a variety of forms.In this paper, the author seeks to delineate certain broad trends which are occurring relative to industrial minerals and the environment and then, through a series of examples, to outline opportunities, developments, and impacts respecting a number of industrial minerals produced and consumed in Canada and the United States."

Jan 1, 1996

By C. Dragusanu, J. Sims, J. Connolly

Based on a statistical analysis of the categorical and numerical data from the established geological model, a geochemical classification of mineralization has been shown to be objective in nature and correlated to the envisioned metal extraction process. Multivariate chemical classification has the potential to discriminate within a combined response from different types of alteration and metal abundances. Distinct domains of chemical response determined by clustering analysis were used as a validating criterion for a geologically driven metallurgical testing program. The groups established are spatially linked to the geological process responsible for their genesis, providing clarity in geometallurgical and resource modeling.

Jan 1, 2011

By P. A. Christopher, R. H. Pinsent

"The Adanac molybdenum porphyry deposit near Atlin, in northwestern British Columbia, was discovered in 1905. It was explored extensively between 1967 and 1980.The deposit is within a complex, multi-phase, quartz monzonite stock that is a satellite of the post-accretionary, Surprise Lake Batholith. Biotite K-Ar dates range from 703 ± 2.4 Ma to 71.6 ± 2.1 Ma, indicating a Late Cretaceous age of emplacement.The deposit comprises an irregular-shaped ring or halo peripheral to a quartz monzonite porphyry dome, or ""cupola': The shape of the ring, and of a smal~ fine-grained quartz monzonite intrusion, and the presence of higher-grade mineralimtion on the eastern flank of the cupola, suggest partial control by a preminera/ structure. The deposit is truncated by a steep, northwesterly dipping, normal fault (Adera Fault) that down-dropped the northern half of the deposit by a minimum of 100 mThe deposit lacks strong zonal alteration but there are narrow envelopes of potassic alteration around some veins and local zones of intense wall-rock silicification. There is considerable retrograde alteration along postminera/ faults and fractures.Molybdenite occurs in veins and fractures, many of which are relatively flat-lying. They occur in all phases of quartz monzonite. Molybdenum is the only element of economic significance. There are vein and skarn occurrences with tungsten, tin, lead, zinc and precious metals peripheral to the deposit.In 1981, Placer Development Limited reported an ""undiluted mineable mineral reserve"" of 151 971 000 tonnes grading 0.063% Mo at a cutoff grade of 0.04% Mo and a strip ratio of 1.5:1."

Jan 1, 1995