Search Documents

By Brian Fulcher, Michael Bell, Shimi Tzobery, Werner Burger, John Bednarski

The Arrowhead Tunnels Project represents the final portion of a 70 km (44-mile) long water conveyance facility that will bring up to 28 m3/sec (1,000 ft3/sec) of water into Southern California. The 13 km (8-mile) tunneling project is well underway and consists of two, 5.8 m (19-foot) diameter TBM bores through extremely variable geological conditions. The tunnels lie near the base of the San Bernardino Mountains and several significant faults including the San Andreas Fault run within one kilometer (0.6 miles) of the tunnel alignment. Numerous other significant faults cross the tunnel alignment and water pressures in the tunnel have been recorded as high as 20 bar (300 psi). This paper describes some of the problems and challenges encountered and the solutions implemented to advance the two hybrid TBMs under conditions that ranged from hard rock with no water inflows to full-face granular material under 10-bar pressure and in excess of 32 l/sec (500 gpm) inflows. Due to the range and severity of ground and water conditions actually encountered, the Owner-Contractor-Designer team eventually found that adjusting the means and methods to be more responsive—virtually on a day-by-day basis—was needed to suit the conditions

Jan 1, 2007

Additional Attractive Force Between Alumina Particles Due to Low Solubility of Dicarboxylic Acids

Sep 13, 2010

By D. I. Bleiwas

The Bureau of Mines determined demonstrated tin resources and costs associated with tin production in order to evaluate the potential for tin production from 18 market economy countries (MEC's). Data were collected from tin producers, in most cases during on-site visits. The analyses evaluated the relative economic and resource position of 146 mines, deposits, or regions in January 1984 dollars. The demonstrated resource of recoverable tin within the nations studied is approximately 2.8 million metric tons (mt). Of this total, over 73 pct is recoverable from the Southeast Asian countries of Malaysia, Thailand, and Indonesia, which in 1983 accounted for almost 60 pct of the world's tin production. Brazil has joined the Southeast Asian countries as a major low-cost, high-volume supplier of tin and is likely to continue to expand its production. Given the 1984 market structure, over 60 pct of the tin in demonstrated resources was economically recoverable. Historically, the International Tin Council (ITC) has helped maintain relatively stable tin prices through a buffer stock and sales quotas. In late 1985, exhaustion of buffer stock funds led to suspension of tin trading on the world's major tin metal exchanges.

Jan 1, 1986

At last year's. annual meeting of The Institute, Sir George Fisher, as President, compared it somewhat nostalgically with a meeting of its kind in the 1920s when comment was expressed on the decline of Australianmining and on the lack of new mineral discoveries.I feel that tonight's annual meeting is even more an occasion for nostalgia, for it represents the seventy-fifth anniversary of the founding of The Australasian Institute of Mining and Metallurgy. I hope, therefore, that I may be allowed to retrace some of the circumstances of this Institute's origin and at the same time to look at some of the broader happenings of those 75 years.From this distance in time it is, of course, much easier to get things in perspective and one of the things that compels enormous admiration in looking back over the history of our Institute is to note the qualities of foresight and keen concern for professional standards which moved the pioneers in this Institute. They had no benefit of hindsight to aid them.Just over 75 years ago, a small group of men met in Broken Hill to discus.s the possibilities of forming an association of mining engineers. The moving spirit was Uriah Dudley, our first secretary, manager of the Umberumberka mine at Silverton. The first formal move to form an association of mining engineers came from the Amalgamated Mining Managers Association of Australasia. At the time, this association was a fairly new group, being 5 years old.It had been formed to try to raise the standard of management throughout the industry. Uriah Dudley and our first provisional president, John Howell, held their first talks in 1891 and further meetings at Broken Hill followed. The inaugural meeting, attended by 200 members, was held in Adelaide in April, 1893.

Jan 1, 1968

By A. V. Shroff

The Indian Standards code of practice for design and construction of underreamed piles contains provision for installing such piles in expasive soils. In recent years, a large amount of research work has been carried out in the analysis, design, construction and performance of underreamed piles in expansive soils. This paper suggests that the results of this research field tests should be included in the code. Various additions and modifications as well as deletions that should be incorporated in the code are discussed.

Jan 1, 1996

By Moyle F. J

This paper describes an apparatus which was developed to study solid-vapour equilibria and presents results which were obtained during a study of the FeCI3-AlCI3-CI2 system. Analysis of the results showsthat fractional desublimation might offer a means of achieving a useful separation of the iron and aluminium chlorides produced by the chlorination of bauxite. The results, presented in the form of isothermal vapour pressure curves covering the range of temperature 160-200°C, support the earlier findings of Semenenko et al (Dokl Akad Nauk SSSR, 154: 42-43 (1964)) that the solid phase contains two terminal solid solutions.The equilibrium constant for the formation of the mixed dimer, FeAICI6, was approximately 4. The latent heat of sublimation of aluminium chloride varied from 18 to 26 kcal/mole AI2CI6 for solid compositionsfrom 0.9 to 0·5 mole fraction FeCls3.

Jan 1, 1979

By C. P. Kelley, T. J. McKeon

Several recent developments in fine screening technology have been implemented at the DuPont Starke, Florida plant allowing enhanced zircon recoveries while minimizing operator requirements and total operational costs. The total design concept came about through the efforts of engineers at Derrick Corporation (Buffalo, New York), DuPont Titanium Technologies (Starke, Florida) and Roche Mining (Carrara, Australia). The use of the Kelsey Jigs for zircon recoveries from the tailings stream requires two wet sizing functions in order to operate properly. The first wet sizing is required on the initial mineral slurry feed to the Kelsey Jig. This sizing is intended to protect the Kelsey Jigs internal screen basket from plugging with nearsize particles, thereby keeping production rates maximized. The second sizing function is intended to recover properly sized garnet ragging material, which inadvertently ends up in the tailings stream leaving the Kelsey Jig. The unique machine design developed by the three partners in this project incorporated both wet sizing functions (protection and garnet recovery) into a single patented high capacity wet screening machine fitted with patented screen surface technology. This screen surface technology allowed for high capacity slurry handling capabilities at separations as fine as 230 microns while experiencing no nearsize blinding and extremely long screen panel life. The high open area urethane screen surfaces utilized in the application typically last 20 to 30 times longer than stainless steel wire surfaces. The stacked machine design minimized total equipment requirements and screen footprint requirements, and reduced power consumption and overall installation costs.

Jan 1, 2005

By Mauricio Terceros, Martin Achmus, Freddy Lopez

The massive use of deep foundations had a remarkable influence in the building industry in the 20th century. Piles and micropiles made possible to erect thousands of civil structures around the world, changing quintessentially the urban and rural landscapes. Especially in urban areas, the ongoing development requires not only new infrastructure, but also to increase the capacity and/or to extend the serviceability of existing structures (buildings, bridges, etc.). Factors such as the change of use of existing facilities or the requirement to comply with updated building regulations confront Civil Engineers with the question, whether to tear down and build new structures, or to reinforce the existing structures from their foundations. Micropiling has enabled designers to come up with technical feasible solutions to retrofit the existing deep foundations, making the structural reinforcement a real option, even under considerable changes in the loading conditions. The following article presents an overview of an intervention project, where micropiles were designed to reinforce the original pile foundation of an existing building, enabling it to be reused with a different structural function. This paper will focus mainly on the analysis of the interaction between the existing piles and the reinforcing micropiles, especially in terms of settlements’ compatibility. Finally, the adopted solution, with its correspondent design considerations and execution process will be presented.

Jan 1, 2018

By Timothy J. Rohrbacher

This report presents results from an ongoing U.S. Bureau of Mines study defining domestic coal reserves. Examinations of five 7 ½ -minute central Appalachian quadrangles have been completed to date. Only 26.4%, 5.0%, 6.5%, 8.2%, and 4.2% at the coal resources remaining in the Matewan, Boltsfork, and Hoskinston, KY; Vansant, VA; and Beckley, WV quadrangles, respectively, constitute economically recoverable reserves. An evaluation of the coal mining industry's impact on the economy of Pike County, KY, wherein the Matewan quadrangle is located, was also completed in order to provide a basic understanding of the influence of coal mining on the local economy. Results show that coal mining is the only major income producing industry in Pike County, accounting for about 46% of the county's income, and 21% of the total available employment, in the base year 1990. If similar results are found in subsequent investigations, a strong argument can be made that traditional coal producing regions may soon be experiencing resource depletion problems far greater and much sooner than previously thought. This will affect not only the coal industry but, given the obvious dependence of Pike County's economy on its coal mining industry, the entire social and economic infrastructure of large areas.

Jan 1, 1994

By D. L. Murr, J. R. Jensen

Testing was conducted on a Minnesota Iron Ore concentrate with Cook Clay as a binder using compressive sheer mixing to enhance the performance of the agglomeration mechanism. The testing was conducted on a bench scale at the Midland Research Center the summer of 2004. Results of the test program will be presented that shows the impact of compressive sheer mixing had on the strength achieve in a green ball.

Jan 1, 2006

By J. D. Potts

Dust surveys were conducted at six underground coal mines to determine if deep-cutting practices expose face workers to higher levels of respirable dust. The surveyed mines were able to successfully mine deep cuts without significantly increasing the dust exposures of face workers. For exhausting face ventilation, field data indicate that scrubber airflow is the most important factor for controlling dust. Data collected for this study indicate that 20-mesh screens should be cleaned for every 40 ft of advance because 22% of the deep cuts surveyed for this study experienced a 20% to 35% decrease in scrubber airflow over the course of the cut. For blowing face ventilation, field data and past research indicate that dust control is aided by maintaining a proper curtain-to-scrubber airflow ratio of 1.0 (measured before scrubber activation) as well as a curtain setback distance that allows the miner operator to stand at the mouth of the curtain for the entire cut. Dust levels on the bolting faces did not appear to be affected by the longer cycles associated with deep-cut mining when good ventilation practices were used.

Jan 1, 2011

By Lawrence P. Goldfarb

This paper presents the results of the geotechnical investigation for the repair of the Fashion Island Boulevard Bridge, Bridge No. 350160, in San Mateo, California. The concrete, precast girder bridge suffered considerable damage during the Loma Prieta earthquake. The existing 36-inch, precast, prestressed concrete piles cracked and spalled at their tops. Based on analyses performed by Biggs Cardosa Associates, structural engineers, the piles did not have sufficient strength and ductility to resist the dead plus seismic loads specified in the Caltrans "Bridge Design Specifications". Additional support for the bridge was needed and the repair strategy consisted of installing large diameter pipe piles at the existing bent and abutment locations. This paper describes the geotechnical engineering analysis and design decisions for the large diameter pile design.

Jan 1, 1993

By D. L. King, C. D. Rubert, R. W. Christy, B. A. Schepman

R. W. Christy (Manager of Sales, Sanitary Engineering Equipment, Link-Belt Co.) and C.D. Rubert (Barrett, Haentjens & Co.) — Messrs. King and Schepman have presented an excellent paper which outlines the general practice in the design of thickener mechanisms. Lifting devices, controls, special applications and underflow pumping arrangements have been reviewed in detail. Pumping arrangements were illustrated which eliminate the need for an expensive tunnel beneath the thickener floor. Most of those illustrated have the common feature of a relatively long underflow suction line extending from the hopper floor to the pump located on the bridge at the periphery of the tank. The authors limit these arrangements to comparatively dilute or thin slurrys. It is implied that dense and coarse concentrates, which are difficult to pump, cannot be handled unless a tunnel is constructed. Fig. 1 shows an underflow pump arrangement which negates the need for a tunnel but which permits the operator to convey a heavy dense slurry. The pump is mounted directly on the fixed hoist platform and the impeller is located at the base of the steel center column. Priming water is not needed. The column

Jan 1, 1963

By J. Allan Tice

In the past fifteen to twenty years, the use of drilled piers to support high capacities in coastal plain deposits has become more and more common. With improved construction techniques and better understanding of pier behavior, drilled shafts with capacities of 200 to 500 tons are not unusual. The purpose of this presentation is to review several drilled pier installations from North Carolina to north-east Florida as a means of illustrating the different types of design concepts and installation techniques which are presently being used. ACKNOWLEDGEMENTS The information in this presentation was obtained from work performed by many individuals and companies. The section on limestone socket caissons in South Carolina is an abridged version of a paper prepared by Rob Smith and Neil Gilbert of Law Engineering's Charlotte, North Carolina office, and is used with permission. The section on pier installation in northeast Florida is an abridged version of a paper prepared by Kirk Mcintosh, Tom McDaniel, and Randy Knott of Law Engineering's Jacksonville, Florida office, reprinted here with permission. Additional data discussed in this presentation has been obtained from Farr Foundation Company, McKinney Drilling Company, and Peterson Drilling Company.

Jan 1, 1988

By Ramin Motamed, Joseph A. W. Toth

Evaluation of the capacity of large-diameter drilled shafts using current load test methods present challenges when considering the magnitude of loads required to fully mobilize their capacities. Often, these full scale tests do not fully mobilize the capacity through side resistance. Therefore, the need for innovative solutions to extrapolate side resistance and interpret nominal capacity are of key interest. In this study, we evaluate three methodologies for extrapolating unit side resistance based on bi-directional load test data. Fellenius (2001) presented these methods for interpretation of pile capacity using static load tests. Our interpretations are based on the evaluation of 116 load tests. Unit side resistance was calculated and reviewed for each load test and categorized using three criteria of mobilization; (A) full, (B) partial and (C) linear. This study specifically focuses on load tests that showed fully mobilized unit side resistance behavior (Criteria A). The three methodologies were applied assuming Criteria (A) load tests were mobilized to 50% of their measured values. Subsequent comparisons of each extrapolation were then compared against the full measured values for each test and generally showed good agreement. INTRODUCTION It is widely accepted that conducting load tests such as standard top-down tests or bi-directional (i.e. O- cell) tests can help designers understand load-settlement behavior and the nominal resistance of drilled shaft foundations. These load testing methods provide the advantage of confirming design assumptions as well as improving the reliability of the foundation design. The potential cost savings from the application of these methods for mid to large size projects is self-evident. For example, in a recent project in Northern Nevada, an O-cell test on a 6.9 ft diameter, 114.8 ft length drilled shaft imposed an initial cost of $125k to the project, resulting in a 15% reduction on the total foundation cost; equivalent to $1.3 million in overall savings (Pease, 2014). However, the costs of implementing such methods on smaller projects can be prohibitively expensive (Hagerty et al, 2016). Despite the clear advantages of drilled shaft load testing, the current practice is not without limitations. Performing load tests on large-diameter drilled shafts with high capacities is a challenge considering the significant loads required to fully mobilize the capacity of such foundations. In some cases, the feasibility of these tests is impractical because the associated initial cost is not guaranteed to outweigh the final savings. As a result, large scale load tests are sometimes ruled out from the design phase of projects. Furthermore, in the majority of load tests the magnitude of loads applied are specifically selected to not approach failure, so the shafts can be used in the future foundation system (i.e. production shafts). This practice of field testing restricts our knowledge of the true capacity of the drilled shaft at failure; hence the nominal resistance remains unknown.

Jan 1, 2018

By Hudson S. B

With a particular electrode configuration, and a particular combination of electrode voltage and roll speed, a relatively small increase in electrode voltage, or a relatively small decrease in roll speed, resultsin a marked improvement in the separation of zircon from ilmenite. In general, fine minerals can be separated using a higher roll speed, or a lower electrode voltage, than is required to separate coarse minerals. The ionizing electrode should be reasonably close to the point at which mineral is fed on to the roll, and nearer to the roll than the non-ionizing electrode. The optimum conditions for the separation of zircon from ilmenite may not apply for the separation of other non-conductors from other conductors.INTRODUCTIONAlthough the high tension separators used in the Australian beach sand industry are efficient, this efficiency has been gained very largely by a process of trial and error, and not by a systematic study of the effects of changes in the operating variables. The optimum roll speed for a particular electrode position and electrode voltage, and the optimum electrode voltage for a particular roll speed and electrode position, can both be determined quite readily. It is not so simple to determine the optimum electrode position for a particular electrode voltage and roll speed. The reason for this is that the electrode used in high tension separators consists of two parts-an ionizing and a non-ionizing electrode respectively. The angular and radial positions of these electrodes, relative to the feed roll and to each other, affect the behaviour of conductors and non-conductors to varying degrees.

Jan 1, 1962

By John Dean Smith

"In many operations the two most overlooked aspects in the drilling and blasting process is theblast optimization and explosive selection. Often times we find a blast design that seems to work andproduce acceptable results and will use this cut afier cut, even years. When in reality one should never become complacent and should be constantly looking for ways to improve the drilling and blasting operation."

Jan 1, 1995

By [D. N. ] Naresh

During different activities pile installation like pile boring, concreting etc., it is likely that various problems, depending up on site condition may be encountered. There are possibilities that some of the activities if not correctly followed may affect the pile capacity. This paper describes few problems encountered during pile execution at different sites and presents the remedial measures undertaken to overcome them.

Jan 1, 1996

By Huw Williams

It is becoming increasingly common practice to re-use existing foundations for new projects, especially on urban sites where geotechnical conditions are congested. A knowledge of the foundation dimensions and capacity is essential for this to take place, however, as-built records are often non-existent. Non-Destructive evaluation (NDE) is now becoming an important tool in assessing old foundation properties and their potential for re-use. Pile dimensions are also critical in the power industry, when they are supporting transmission towers which need to be upgraded, and may carry additional wind loading. This paper describes the application of various NDE techniques that are available and how they can be used to determine pile length, shape and capacity in difficult site conditions, including foundations under structures.

Jan 1, 2006

As this is the first occasion I have had, and probably will be the only opportunity I shall have, of addressing such a large gathering of members and of student members of the Institute, I desire to- express my very deep appreciation of the honour 'you have paid me in electing me to the office of President for the current year. I realise also that such selection is a tribute to the Company which controls operations here, the centre selected for the annual meeting, but nevertheless there is afforded to the recipient a great deal of pride and of pleasure to hold the highest office in what is, in my opinion, undoubtedly the most important engineering society in Australasia.The past year has witnessed an unprecedented and unparalleled event in the history of the British Empire, and I think that we must all feel a wonderful sense of proud patriotism; the whole world was forced to admire the public calm and the dignity which accompanied the change in our Sovereign Ruler, and great tribute is due to the statesmanship of the Prime Minister, Mr. Baldwin. At this time, we should, I think, place on record our prayer, in common with all his people, that His Majesty, King George the Sixth, may enjoy a long and prosperous reign.The meeting at Port Pirie recalls one who did so much for the advancement of mining and metallurgy, especially in Australia. I refer to the late Mr. Delprat, who, as General Manager of The Broken Hill Proprietary Company Limited, had under his control for many years the smeltery in this centre. As you are aware, he had been elected an honorary member of this Institute, as well as of our sister Institutes in England and in America...

Jan 1, 1937