Search Documents

By Richard J. Hartman

Current design practice is to select steel sheet piling sections using sufficient section modulus and yield strength to resist the calculated bending moment. Thus, section modulus is the only property of the sheet pile cross section used in the selection process. Full scale laboratory testing documented that section modulus alone is insufficient to predict the strength of sheet piling. During testing, sheet pile sections with equivalent section modulus exhibited as much as 75 percent difference in load resisting capacity. Analytical study following the testing established that, in addition to the traditional longitudinal (vertical) stress in sheet piling, transverse (horizontal) stresses are also present. Transverse stresses reduce the ability of the sheet piling to function in the intended manner. It was found that transverse stresses result from the pressure applied by soil and water and that the capacity of the sheet piling diminishes with increased pressure. All sheet piling is subject to this behavior. This paper describes the testing and the results and establishes that a problem exists. A two dimensional procedure is described that assists in evaluating transverse stresses and their effect on sheet pile capacity. A method of creating design aids for use by engineers is illustrated.

Jan 1, 2006

By Liqun Liang

Various nondestructive testing (NDT) inspection methods are available to evaluate the structural integrity of cast-in-place shafts. The widely used methods include Cross Hole Sonic Logging Testing and Low Strain Testing. Due to its advantages such as low cost, easy operation, quickness and flexibility (no need to plan ahead and prepare inspection tubes or other devices), Low Strain Test is frequently specified in quality assurance programs of many countries or when doubts arise as to the integrity of the finished shafts/piles. The method is well suited for small to middle sized shafts. However it is an indirect NDT testing method and has certain limitations. Data interpretation requires proper training, experience and judgment and, therefore, inconsistent conclusions and reporting may be provided by different testers. To avoid or reduce such inconsistencies, it is best to follow a standardized data interpretation and record classification system. In this paper, a new classification method is presented with examples. A step-by-step data evaluation and interpretation procedure is proposed with examples of real cases to help understand the LST data. The paper also makes recommendations for measures to be taken when anomalies are detected in tested production piles.

Jan 1, 2011

By Jilai Xue

Fe-Ni alloys can be used as raw material in making stainless steel. Laterite nickel ore is one of mineral resources for producing nickel alloys. In this work, the laterite ore after dehydration at 800 °C and the anthracite as reducing agent were mixed for pre-reduction at 900 °C, and then reduced to form Fe-Ni alloys at 1550-1620 °C through carbon-thermal reduction process. A high Ni-content alloy component in the metallurgical mixture can be formed through pre-reduction. Better separation of the resulting metals from the slag is found with lower Ni-content alloys produced or higher temperatures during reduction. An effective processing of Fe-Ni alloys needs further understanding of the process fundamentals and optimizing of the process parameters.

Jan 1, 2010

By Michael McVay

The use of augered cast-in-place piles has seen tremendous growth under commerical structures in the past twenty years. Problems with vibration, soil densification and/or heave associated with driven piles do not occur with properly installed augered piles. Augered cast-in-place piles were originally constructed (1950s) with diameters of .31 m (12 in.) and lengths up to 6.1 m (20 ft); however with the advent of better drilling equipment, diameters varying from .41m(16 in.)to .61 m (24 in.) and typical depths ranging from 18.3 m (60 ft) to 24.4 m (80 ft) are achievable. Reinforcement may vary from a single high strength rebar (Grade 60) at the top of the pile to a continuous steel cage depending on loading (compression, tension-uplift, and lateral). Typical axial design loads (compression) for a single augered cast-in-place pile are in the 445 kN (50 tons) to 890 kN (100 tons) range.

Jan 1, 1997

By Gavin Ritson, Chris Ward

"The oil sands industry is still fairly young with the first viable oil sand operation having been started in Alberta in 1960. Since then numerous modifications and improvements have been tried and implemented. The current process makes use of high velocity pumping of oil sands slurry with hot water (hydrotransport) to achieve separation of bitumen from the sand.A number of the oil sands processes have been adapted from unit operations that are used in mineral processing, such as crushing, screening, flotation, cycloning and thickening. This paper outlines a typical oil sands process flowsheet and investigates the differences and similarities in technologies and costs to other mineral processing industries. It also considers the very large throughputs required, and presents some of the difficulties and challenges currently faced by the industry as a result of high demand for oil and environmental pressures.INTRODUCTIONOil sands (also known as tar sands) deposits are found throughout the world. The Athabasca Oil Sands deposit in Aberta is the largest of these. Oil sands consist of a mixture of crude bitumen (a semi-solid form of crude oil), silica sand, clay minerals, and water. The Athabasca, Peace River and Cold Lake deposits cover 141,000 square kilometers and contain about 1.7 trillion barrels (270×109 m3) of bitumen in-place, comparable in magnitude to the world's total proven reserves of conventional oil"

Jan 1, 2009

For the past four years, the Department of Mining Engineering at the University of Kentucky has conducted a validation study of the CFD Fluent code, by comparing its results against mining-related benchmark experimental data provided by NIOSH?s Pittsburgh Research Laboratory. This particular study is dedicated to the effect of machine-mounted dust scrubbers on the performance of face ventilation systems using extended-cut mining with a blowing curtain.

Jan 1, 2009

In 2002 the authors updated the MFire model developed by the US Bureau of Mines. MineFire, developed by Mine Ventilation Services, Inc. (MVS), uses the MFire model to perform mine fire simulations on typical mine ventilation networks. The MineFire program is capable of producing visual schematics and other analysis tools for input and output of the MFire model. The MFire model, however, was limited to 500 branches and 10 fans. This paper discusses the newly modified MFire model that is now capable of modeling over 5000 branches and over 400 fans among other expansions and improvements. Given the long history and proven track record of MFire, the expansion did not modify the core calculation methods or results. This paper focuses on a general discussion of the MFire program and issues encountered in expansion of the algorithm. An example large network with simulation results is discussed.

Jan 1, 2011

By Henry Rawdon

THE following note describing the behavior of copper under rather unusual conditions is offered here for its suggestiveness rather than as a complete study of the question. The examinations described were made because of a request for information concerning the embrittlement of copper when heated in a molten salt bath (sodium chloride) for the purpose of cleaning it, as well as for softening it. It is well known that metals may be rendered very brittle by electrolytic action, in aqueous solutions, in all probability by the action of nascent hydrogen, and it was suspected that perhaps the embrittlement of the copper by means of the molten salt was produced in a somewhat similar manner. It was found that the copper was in contact with iron (or steel) while immersed in the molten salt, through the occasional use of an iron stirring rod, iron forceps for handling the pieces, and an iron pot for containing the fused salt. In the electrochemical potential series iron and copper stand some distance apart, copper being electronegative to the iron. Assuming that the two metals bear a similar relation to each other, when immersed in a bath of molten salt, as they do in an aqueous solution, they would be expected to form a galvanic couple, the copper being the cathode. By this means the copper might be embrittled, as often happens in aqueous solutions, by the action of the liberated hydrogen. In this case, however, the embrittlement must be attributed to some other agent than hydrogen. To demonstrate how copper may be embrittled under these conditions, two small rods, one of copper and the other of mild steel, approximately 3/8 in. (9.5 mm.) in diameter, were immersed in a bath of sodium chloride that had been heated somewhat above its fusion point (melting point of sodium chloride is 819° C.) and an electromotive force of approximately 6 volts from a storage battery was impressed upon the system. The copper was made the cathode and the action was continued for

Jan 2, 1920

Drill cores from Section 62, New Broken Hill Consolidated Ltd., were used to study the petrology of rocks associated with the zinc lode. The distribution of the rock types in relation to the lode structure was determined. The distribution of the gahnite-bearing rocks was shown to be only partly conformable with the structure.It was concluded that large scale metasomatism was not widespread, that the rocks associated with the lode (except, perhaps, the quartz-gahnite-garnet rocks) were formed by metamorphism of sediments, and that rocks and lode were contemporaneously metamorphosed.INTRODUCTIONThis investigation was undertaken in order to study the rock types associated with the zinc lode of the Broken Hill orebody, and their relationship to the structure of the ore horizons. The work was confined almost entirely to the laboratory, and is therefore limited in its scope. It is hoped, however, that the information gained may throw some new light on the genesis of the lode.Certain inferences which are drawn from this work are at variance with the ideas of a number of earlier workers.In particular, the idea of large scale metasomatism developing many of the rocks associated with the lode, especially those containing manganese, is questioned. On the contrary, the rocks associated with the lode are more simply explained as highly metamorphosed sediments, in some cases modified by water introduced from surrounding rocks into zones of strong folding and faulting. As a corollary, a metamorphicsedimentary origin for the lode material, either as a concentrated sulphide deposit, or somewhat disseminated...

Jan 1, 1961

By J. Andrew Cornier, Mike Cooper

"Upon successful completion of the AG/SAG Mill project (Cooper et al., 2001) the Brunswick Mine concentrator was configured with single line processing through the AG/SAG mill, followed by two parallel ball mill and flotation circuits. The Stage Grinding project was undertaken to utilize a pre-flotation stage on the AG/SAG mill primary cyclone overflow and simplify the flowsheet by consolidating the two ball mill and flotation circuits, resulting in single line processing fi-om AG/SAG mill to final concentrate. Concurrently, the reclaim water supply capacity was increased to enable flotation cleaning at lower percent solids.Benefits from the Stage Grinding project include revenue enhancement from increased zinc grade and recovery combined with additional lead recovery. Further benefits included a reduction in the number of process pumps, reduction in loss associated with spillage to sumps and process simplification through efficient use of equipment layout.The Stage Grinding project was implemented in six phases over a period of seven months in 2000. Each phase was commissioned during scheduled concentrator shopdays with minimal additional downtime required. One year after project approval the Stage Grinding project was completed at a total cost of $1 1.8 million.INTRODUCTIONThe Noranda Inc. Brunswick Mine, located near Bathurst, New Brunswick, is one of the world’s largest leadzinc mines. Milling of ore began in 1964 from the No. 12 orebody, with an expansion in 1966 to accommodate ore fkom the No. 6 open pit located several kilometers away. In 1980 the pit was exhausted and the concentrator rationalized to accept a design feed rate of 10,500 tomes per day from the No. 12 mine. In excess of 100 million tomes have been milled to date, representing over three-quarters of the known reserve. The concentrator employs differential froth flotation to produce lead, zinc, copper and leauzinc bulk concentrates. The ore is massive sulphide, with approximately 20% valuable minerals, 60% pyrite and 20% silicates."

Jan 1, 2002

By L. Yuan, A. C. Smith

To provide insights for the optimization of ventilation systems for U.S. underground coal mines facing both methane control and spontaneous combustion issues, a computational fluid dynamics (CFD) study was conducted to model the potential for spontaneous heating in longwall gob areas. A two longwall panel district using a bleeder ventilation system with a stationary longwall face was simulated. The permeability and porosity profiles for the longwall gob were generated from a geotechnical model and were used as inputs for the CFD modeling. In this study, the effect of methane emissions from the mined coal seam, including the longwall face and overlying rider seam reservoirs on the gob gas distribution was considered. The spontaneous heating is modeled as the low-temperature oxidation of coal in the gob using kinetic data obtained from previous laboratory-scale spontaneous-combustion studies. Unsteady state simulations were conducted, and the effects of the coal’s apparent activation energy and reaction surface area on the spontaneous heating process were also examined.1

By Brian Hart, Hong Zhong, Liuyin Xia, Kyle Douglas

"The application of hydroxamic acid as flotation collectors is fast becoming of significant interest for the selective flotation of oxide minerals along with upgrading oxidised based metal ores and minerals. In the hydroxamate molecule, both O and N atoms in the -CONHOH group are identified as coordination atoms in many complexes and their characteristic structure determines the strength of the chelation complex between the hydroxamate and metal ion. The chelating performance of hydroxamates with transition metals including Cu, Ni, Zn, Fe, Cr, Mn and Co, the alkaline-earth metals (Be, Ca) and heavy metal (Pb) has been studied. Cytec has developed and patented a range of alkyl hydroxamates as flotation collectors for oxidised base metal sulphides, metal oxide minerals and precious metals. This paper introduces two new structures of hydroxamate collectors (Cyclohexyl and 4-tert-butylbenzoyl hydroxamates) and evaluates their characteristics relative to alkyl and benzoyl hydroxamates. Laboratory small-scale flotation tests were conducted with ilmenite and wolframite. The use of 4-tert-butyl benzoyl hydroxamate resulted in a best flotation performance for ilmenite. A relatively low cyclohexyl hydroxamate dosage was required in the flotation of wolframite to obtain comparable results to the alkyl and benzoyl hydroxamates. It is also shown a significantly improved flotation performance with 4-tertbutyl benzoyl hydroxamate in the flotation of ilmenite plant ore in comparison to the oleic acid or fatty acid collectors typically used for ilmenite flotation.INTRODUCTIONHydroxamic acid has been reported as an effective collector in small-scale flotation tests for a wide variety of oxide minerals and ores including copper (Lee et al., 1998, Lee et al., 2009), iron (Quast, 2000), tin (Sreenivas and Padmanabhan, 2002; Wu and Zhu, 2006), tungsten (Marinakis and Kelsall, 1987; Xia et al.,2004), and rare earth metal minerals (Ren et al., 1997; Pradip and Fuerstenau, 1991; Assis et al., 1996; Pavez et al., 1996; Zheng et al., 1996; Chen et al.,2005).As part of our previous research project, a selected suite of hydroxamic acid collectors including fatty, aromatic and modified hydroxamates (naphthoyl, cyclohexyl, benzoyl, octyl, 4-tert-butyl benzoyl, salicylic hydroxamates) were tested in order to examine their potential for recovery and selectivity of rare earth minerals. In these tests it was shown that the flotation performance with the hydroxamate collectors was significantly better than the phosphoric acid collectors on no slimes removed samples (Brian, et al., 2014; Liuyin, et al., 2014 and unpublished internal technical reports). Furthermore the tests revealed that for most of the hydroxamate reagents tested, their dosage requirements to achieve recoveries at the same levels was less than that for the phosphoric acid collectors. Recovery of both La and Ce was significantly better for the salicylic hydroxamate and that Nb, Y and Zr recovery were favoured by the octyl and benzoyl hydroxamates (Brian, et al., 2014; Liuyin, et al., 2014). Comparison among the hydroxamate collectors showed that the flotation and recovery performance of cyclohexyl (CHH) and 4-tert-butyl benzoyl (TBH) was not as good as the other hydroxamates for rare earth recovery."

Jan 1, 2015

By S. E. Phillipson

Underground mine mapping is a critical component of understanding the controls on ground instability. Many relatively localized examples of ground failure are associated with geologic features, such as faults, joints, compaction zones, or sedimentological transition zones. In contrast, long-running, directional roof falls are associated with regionally directed horizontal stress fields, which are induced by tectonic plate interactions in the earth?s crust. When stress-related features are distinguished from geological features, underground mapping can be an effective method for inferring the direction of horizontal stress at individual mines. Comparisons with data compiled in the World Stress Map confirm that underground mapping can be a valid method for determining the orientation of maximum principal horizontal stress at a variety of scales, ranging from individual mines to an entire mining district or coal basin. Comparisons are presented between the maximum horizontal stress directions inferred by MSHA?s Roof Control Division through underground mapping and the azimuths of maximum horizontal stress in the World Stress Map database for North America?s Pennsylvanian-aged Appalachian, Illinois, Black Warrior, and Arkoma Basin coal fields. The comparison indicates that azimuths are similar for both data sets, even where variations in the direction of horizontal stress are present. It is interpreted that inconsistencies in direction are attributable to near-surface affects such as deeply incised stream valleys, or to fault zones that represent heterogeneities in the crust.

Jan 1, 2009

Modelling and simulation are important aspects of flotation research, which may assist in the design of new circuits and the optimisation of existing ones. Flotation research in the AMIRA P9 project has developed a methodology for flotation plant modelling based on determination of cell (pulp) characteristics. froth characteristics, and ore floatability (using floatability components). The implementation of this methodology requires the determination of ore floatability, to which end a small flotation pilot plant known as the Floatability Characterisation Test Rig (FCTR) has been designed and then built and kindly made available to the AMIRA P9 project by Baker Process. The FCTR has a 2 tph capacity and consists of six 130 litre rougher/scavenger cells and six 50 litre cleaner/recleaner cells. The Mintek FloatStar pulp level control system is used to control the pulp level in all cells. A number of experimental procedures have been developed for using the FCTR to obtain the data required for the P9 flotation models. These procedures include how to determine the floatability parameters, Pi and mi, the bubble surface area flux, Sb, the mean residence of the pulp in the cell, t, water recovery. Rw, froth zone recovery, Rf, and the degree of entrainment, ENT. The flexibility of the FCTR allows it to be used in numerous flotation studies such as stream characterisation, reagent testing, grinding experiments, power studies, oxidation studies, and scale-up and simulation studies. This paper will describe the design and operation of the FCTR and the procedures that will be used to obtain data from the rig for modelling purposes.

Jan 1, 2000

By John E. Urosek, Dennis A. Beiter, William J. Francart

In This Chapter [Designing bleeder systems Examining and maintaining bleeder systems Evaluating bleeder system effectiveness] INTRODUCTION Bleeder systems are that part of the mine ventilation network used to ventilate pillared areas in underground coal mines. Pillared areas are those in which pillars have been wholly or partially removed, including the areas where coal has been extracted by longwall mining. Bleeder systems protect miners from the hazards associated with methane and other gases, dusts and fumes, and oxygen deficiency that may occur in these mined-out areas. Effective bleeder systems control the air passing through the area and continuously dilute and move any methane-air mixtures and other gases, dusts, and fumes from the worked-out area away from active workings and into a return air course or to the surface of the mine. A bleeder system includes the pillared area (including the internal airflow paths), bleeder entries, bleeder connections, and all associated ventilation control devices that control the air passing through the pillared area. Bleeder entries are special air courses designed and maintained as part of the mine ventilation system. [This chapter focuses on the design, examination, maintenance, and evaluation of bleeder systems in underground coal mines.] The history of coal mine explosions in the United States is a reminder of the importance of adequate ventilation. Some of those disasters were the result of inadequately ventilated pillared areas. The importance of developing bleeder systems to ventilate these pillared areas and evaluating the bleeder system’s effectiveness is reflected in present-day federal regulations. For more information on bleeder systems, see Tisdale [1996] and Urosek and Francart [2002].

Jan 6, 2006

By Nolan Eckroade, Nigel Pereira

Wireless electronic blasting systems are a new technology that enable truly wireless initiation through rock, air and water. This is achieved using low frequency magnetic induction waves to wirelessly send a firing command to groups of in-hole primers. Fully wireless initiation not only removes the limitations imposed by a wired connection to each primer in a blast, but also enables users to alter the paradigm of conventional mining techniques to advance operational productivity and reduce personnel exposure to high-risk activities. While initially deployed in underground applications, wireless electronic blasting is now being used in the open cut environment. To capture the early impacts in surface mining operations, case studies conducted at three surface mines evaluated blasts utilizing a wireless electronic blasting system against baseline blasts using conventional, wired initiation systems. The purpose of this paper is to outline the specific learnings associated with wireless electronic blasting in surface mining to date. The paper will include references to these specific case studies as well as benefits realized and applications for the future.

By McIntosh A. H, Torlach J. A

Since the last paper on mining methods was presented to the Annual Conference of the Australasian Institute of Mining and Metallurgy in 1:960, numerous advances have been made in drilling and blasting techniques at Mount Morgan. This paper describes the drilling and blasting methods being employed in the open cut. The change over to track mounted percussion drills for all types of primary drilling is almost complete and new techniques such as detergent drilling and pressure loading of ANFO are being applied successfully.

Jan 1, 1965

By Sandeep Kumar Jeripotula, Govinda Raj Mandela, Aruna Manglapady

Dumper operators are frequently exposed to whole body vibration (WBV) in surface mines. Surface mining activities involve the amalgamation of comparatively high intensity of vibration and extended exposure durations. Efficient risk reduction mandates knowing of important phases of a task that poses a threat to health of dumper operators. So far in India very limited studies have been reported on WBV exposure with regard to surface mines. This paper evaluates WBV of dumper operators based on ISO 2631-1:1997 Standards and European Union (EU) Directive 2002 for different phases of job cycle. Six dumpers were considered for this study and the vibration measurements were made for all the four phases of the job cycle by placing the triaxial accelerometer on the operator’s seat-surface and at the seat-back, independently. The findings of the study revealed that the haulage task (loaded travel and empty travel) remains the chief contributor to vibration exposure according to seat-surface and seat-back measurements. Maximum frequency weighted root mean square (RMS) of 1.12 m/s2 and 1.09 m/s2 were reported for empty travel task for seat-surface and seat-back measurements, respectively. For seat-surface measurements based on RMS, Z axis remains as the dominant axis of vibration for all the dumpers during haulage task, whereas for seat-back measurements, the dominant axis varies between X and Y. Exposure action value (EAV) based on RMS has exceeded the threshold value of 0.5 m/s2 for all the dumpers during loaded travel and empty travel for seat-surface as well as for seat-back measurements.

By Gray Mullins

This paper presents results from model and full-scale tests to assess the interface bond between a cast-in-place concrete seal slab and steel H-piles in cofferdams. Three different seal slab placement conditions - fresh water, salt water and bentonite slurry - were evaluated and the results compared against controls where no fluid was displaced by the concrete. Normal pile surfaces were investigated. Additionally, the situation of ?soil caked? piles was also tested. In the model tests, eight 15 cm deep, W6 x 15 sections were used for two different embedment depths of 1.5d and 2d, d being the depth of the section. In the full-scale tests, 16 specimens 35 cm deep (W14 x 90 sections) were tested with the embedment varied between 0.5d-2d. The results show that significant bond stresses developed even in the worst placement condition. Recommendations made for revising current values in specifications have already been implemented by the Florida Department of Transportation.

Jan 1, 2013

By Gabriel Esterhuizen

The room-and-pillar mining method is used extensively in underground limestone mines in the Eastern and Midwestern U.S. The rock mass is typically a near-horizontal, bedded deposit at relatively shallow depth. A survey of 34 mines was conducted in which data on roof spans, rock mass properties and support practices were collected as part of a National Institute for Occupational Safety and Health research project into ground control in limestone mines. The average room width is 13.5 m (44 ft), accommodating large mechanized equipment. The results show that the immediate roof beam can consist of many individual layers and can contain several near-vertical joints. In spite of the room widths, the roof is naturally stable in many mines. Observed roof instabilities can generally be related to excessive horizontal stresses or unfavorable geological structures that cause block fallout or beam failure of the bedded roof rocks. The survey showed that the rock mass quality of the limestone does not vary significantly throughout the Eastern and Midwestern U.S. Roof conditions and the need for support were found to be closely related to the thickness and competence of the first layer of limestone in the roof. The findings highlight the need to identify local geological structures and the roof beam characteristics so that support alternatives can be evaluated. Monitoring and observational technologies that are available for identifying potentially unstable roof are presented, which include: roof characterization using the Rock Fall Risk Index, automated logging of roofbolt hole drilling, microseismic monitoring and displacement monitoring.

Jan 1, 2007