Search Documents

By D. Potter

In 1990, Freeport Exploration began regional reconnaissance exploration programs in Irian Jaya, the easternmost province of the republic of Indonesia (Fig. 1). Irian Jaya occupies the western half of the island of New Guinea. Freeport was awarded an initial contract of work that totaled 2.6 million hm2 (6.4 million acres). The company was subsequently awarded additional concessions that added 1 million hm2 (2.5 million acres). The concessions require work commitments and periodic relinquishments. Due to these relinquishments, Freeport’s current land position totals 1.9 million hm2 (4.7 million acres). Freeport began the exploration program to locate additional Grasberg deposits, the largest deposit in the Ertsberg district. But the company recognized that other types of deposits could be present in the largely unexplored area of Irian Jaya.

Jan 1, 1999

By D. Olsen, S. Cole, J. Strid, G. Colzani

This paper focuses on the underground tunnel work at the Hollywood Water Quality Improvement Project (HWQIP) in Los Angeles, CA. The HWQIP is being constructed to provide a water distribution system to bypass the existing Hollywood Reservoir System, which supplies drinking water for 500,000 people. The major project features include, a 2.9-meter diameter 1,829 meter long bypass tunnel, a 1.8-meterdiameter 366 meter long utility tunnel, 3 jack and bore tunnels, two 136 million liters underground circumferentially wrapped pre-stressed concrete water storage tanks, associated piping, and mechanical facilities. The physical project location coupled with strong community involvement and stringent environmental concerns was a considerable driving force for this project located in the Cahuenga Pass area of the Hollywood Hills north of Los Angeles, CA.

Jan 1, 2001

By Kanchan Mondal, Gopi Bylapudi, Anand Bhagwat

Corrosion of steel roof support systems can cause potential premature failure of the support, thus adversely affecting the excavation stability and rock-related safety. An in-house corrosion test system was designed and developed to test full-length roof bolts for material performance based on tensile load capacity and strength under different corrosive conditions found underground. The roof bolts tested are also used to identify the possible corrosion mechanisms that influenced the bolts’ performance over time. Initially, the most commonly used bolt material in the USA, the ASTM A615 grade 60 steel roof bolts, was tested with and without stresses in a simulated underground coal mining environment for approximately 6 months, and the results are discussed. Localized corrosion forms such as crevice and pitting were mainly observed after testing. The stressed and unstressed roof bolts with and without threads that were tested in alkaline coal mine corrosive environment for 6 months passed their load-bearing capacity as per ASTM F432 test standards. From the results, it is concluded that this test protocol could be applicable to test the material performance of different roof bolt metallurgies and coatings with desired modifications to the proposed methodology for the specific underground mine environment. This paper mainly discusses the test system and protocol and shortcomings of the system and makes recommendations based on the observations and results.

By Kanchan Mondal, Gopi Bylapudi, Anand Bhagwat

Corrosion of steel roof support systems can cause potential premature failure of the support, thus adversely affecting the excavation stability and rock-related safety. An in-house corrosion test system was designed and developed to test full-length roof bolts for material performance based on tensile load capacity and strength under different corrosive conditions found underground. The roof bolts tested are also used to identify the possible corrosion mechanisms that influenced the bolts’ performance over time. Initially, the most commonly used bolt material in the USA, the ASTM A615 grade 60 steel roof bolts, was tested with and without stresses in a simulated underground coal mining environment for approximately 6 months, and the results are discussed. Localized corrosion forms such as crevice and pitting were mainly observed after testing. The stressed and unstressed roof bolts with and without threads that were tested in alkaline coal mine corrosive environment for 6 months passed their load-bearing capacity as per ASTM F432 test standards. From the results, it is concluded that this test protocol could be applicable to test the material performance of different roof bolt metallurgies and coatings with desired modifications to the proposed methodology for the specific underground mine environment. This paper mainly discusses the test system and protocol and shortcomings of the system and makes recommendations based on the observations and results.

By Tom Dettweiler, Robina Sharpe, Wright. Michael

The International Seabed Authority and a number of countries have or are in the process of developing environmental impact assessment guidelines and legislation for seafloor mineral development. The formal decision to grant a project an environmental permit is based on an environmental and social impact assessment (ESIA), culminating in an environmental impact statement (EIS). The EIS needs to be supported by sufficient data upon which an assessment of impacts can be made and mitigation measures developed. Given the remote locations of many seafloor prospects, collection of sufficient environmental data to inform an EIS is often a difficult, expensive and lengthy process.

Sep 1, 2014

By Nilabjendu Ghosh, Satyendra Kumar Singh, Gautam Banerjee, Harshit Agrawal

High-production methods like longwall mining with hydraulic powered supports are necessary to increase underground coal production in India. Longwall mining had a mixed success record for Indian geo-mining conditions. In this paper, an analysis is presented to optimally design an array of chain pillars in multi-seam longwall mining panels in the deepest coal mine in India. The study found that a chain pillar of 80-m width and 195-m length is necessary for long-term stability without any reinforcement. It was also observed that an optimum chain pillar can be designed by providing suitable side reinforcement (side bolting) which will reduce the chain pillar dimensions to 55-m width and 160-m length. Optimum design of chain pillars will reduce the coal locked up in these chain pillars by ~ 77%. This will also reduce the gestation period of longwall mining panel development. This paper also evaluates the maximum tensile subsidence strain induced at the surface and finds that the values are within the safe working limit of 3 mm/m. Thus, this paper finds direct application in the design of future multi-seam retreating longwall mining panels in Indian geo-mining conditions.

By Nilabjendu Ghosh, Satyendra Kumar Singh, Gautam Banerjee, Harshit Agrawal

High-production methods like longwall mining with hydraulic powered supports are necessary to increase underground coal production in India. Longwall mining had a mixed success record for Indian geo-mining conditions. In this paper, an analysis is presented to optimally design an array of chain pillars in multi-seam longwall mining panels in the deepest coal mine in India. The study found that a chain pillar of 80-m width and 195-m length is necessary for long-term stability without any reinforcement. It was also observed that an optimum chain pillar can be designed by providing suitable side reinforcement (side bolting) which will reduce the chain pillar dimensions to 55-m width and 160-m length. Optimum design of chain pillars will reduce the coal locked up in these chain pillars by ~ 77%. This will also reduce the gestation period of longwall mining panel development. This paper also evaluates the maximum tensile subsidence strain induced at the surface and finds that the values are within the safe working limit of 3 mm/m. Thus, this paper finds direct application in the design of future multi-seam retreating longwall mining panels in Indian geo-mining conditions.

The following is a summary of some of the companies that were exhibiting their products and services at MINExpo INTERNATIONAL 2000. Atlas Copco develops, manufactures and markets rock drilling tools, tunneling and mining equipment, and surface and geotechnical drilling equipment. The company provides a line of drilling products, including production drilling rigs, rock reinforcement bolts and rock drills. Atlas Copco’s Boomer is a series of high-capacity drill rigs that provides economy, production capacity and reliability

Jan 1, 2000

By T. Wang

A new generated NaNO3 ? NaNO2 ? KNO3 ternary thermal energy storage system which has low melting point as 124°C and high specific heat capacity was studied for the short and long?term thermal stability by using the Thermogravimetric Analyzer (TGA). Based on the actual working condition of molten salt in solar two, the simulated cyclic thermal stability measurement was also conducted. The ternary system demonstrates excellent short ? term thermal stability and thermal reliability after cyclic heating and cooling processes. However, in the long ? term as well as the simulated cyclic stability measurement, large amount of weight loss was observed. Moreover, the stepwise long ? term isothermal study reveals that below 440°C the weight change is minimal and this temperature is viewed as the upper limit temperature of thermal stability for this ternary system. To determine the lost phases at high temperature above the upper thermal stability limit, techniques such as XRD and SEM are used to compare the condition of the salt mixture before and after the long ? term thermal stability study. On the basis of the comparison, it can be concluded that the major weight loss was due to the decomposition of sodium nitrite.

Jan 1, 2012

By Jonathan Baggett, Nino Ripepi, Amin Abbasi, Richard Bishop, Juan Monsalve, John Hole

This work focuses on the operational and safety issues associated with karst voids in large opening underground mines. Issues include water inrush, structural instability, and engineering uncertainty in these environments. Coupled with the fracturing prevalent in folded sedimentary rocks, karst voids are complex and challenging ground-control risks. Traditional methods of predicting karst void locations, such as probe drilling, are impeded by the inconsistent spatial distribution and variable sizes of the features as reported by Li et al. (J Rock Mechan Geotech Eng:232–242, 2010) and Hassan et al. (Procedia Chem 19:737–742, 2016). Ground-penetrating radar (GPR) is a geophysical technique that transmits radio waves into a medium and subsequently detects reflected waves via a receiver. The travel time and energy of received signals are then processed and interpreted. The difference in conductivity and dielectric permittivity between limestone and open karst cavities causes strong reflections. GPR is frequently used as a geophysical surveying technique in several industries; however, there is a lack of published research on underground mining GPR applications as reported by Zhao et al. (2015a; Geophys J Int:62–71, 2015b) and Eskelinen and Pellinen (Constr Build Mater:888–898, 2018). The purpose of this work is to demonstrate the use of GPR in an underground stone mine and to discuss the importance of karst void detection ahead of mining.

By Georgene Renner, William R. Yernberg, Steve Kral

ABB offers complete electrical revamps of mining shovels with ac or dc drives, drive control, frequency converters with insular gate bi-polar transistor technology, intelligent control packages and visualization. Many of the world’s shovel excavators and draglines (walking excavators) were built in the1980s. After 15 to 20 years of round-the clock operation in openpit mines, these machines start to feel their age. Electrical parts are particularly vulnerable. Their performance deteriorates and availability and productivity fall. Even with regular ser-vice and maintenance, a machine of this age will accumulate 400 hours of unscheduled downtime a year. The need for a replacement becomes pressing, but the expense is often prohibitive.

Jan 1, 2005

By A. T. Iannacchione

From 1990 to 1996, 16 states reported 92 injuries from falls of roof, rib or face in the more than 90 underground stone mines in the United States (Fig.1). Missouri, Pennsylvania and Kentucky accounted for 48% of the total number of injuries (Fig. 2). Of this total, 11 miners were killed. Of the 11 fatalities, 10, or 91%, were associated with unrecognized loose or failed rock within the roof beam. Additionally, unrecognized roof beam failures resulted in a majority of the falls of ground injuries occurring in underground US stone mines from1990 to 1996. This number is not large in magnitude. But a workforce of fewer than 2,000 miners makes for a high fatal-accident rate. The severity of the typical fall-of-ground injury is, in general, very high. About three-fifths of all roof, face and rib fall injuries were designated by the US Mine Safety and Health Administration (MSHA) as some kind of lost time accident. MSHA assigns each accident a severity value from one to six. A one represents a fatality, a two, a permanent disability and three, a lost time accident (Fig. 3).

Jan 1, 2000

By T. Rasmussen, T. G. Jørgensen, T. Fischer, R. K. McLimans, C. Knudsen, D. Frei

Ilmenite-bearing paleo-beach deposits were discovered in Jylland, Denmark using a combination of Ground Penetrating Radar (GPR), portable X-ray fluorescence (XMET), bulk XRF analyses, Computer Controlled Scanning Electron Microscopy (CCSEM), and wire line logging. The Miocene-age paleo-beach deposits are located below a thin Quaternary cover in a region of very moderate relief and essentially no outcrop demanding unique approaches in exploration. Initially, an isopach map of the Quaternary is prepared from existing water well data. A geological model for likely occurrence of Miocene paleo-beach deposits is generated and the coincidence of thin Quaternary cover and potential paleo-beach deposits define targets for detailed exploration. The defined targets are traversed with GPR to identify paleo-beach structures which are then used to define a drilling program. This methodology located a paleo-barrier island at the Vorslunde location with more than 10% ilmenite in the sand. During the drilling process, the TiO2 and heavy mineral contents of the sand were logged every meter with a portable XRF unit (XMET) and subsequently calibrated more accurately by comparison to bulk XRF and CCSEM analyses for selected samples. The bulk XRF data also provided more complete compositional information. Insitu determination of geology, heavy mineral abundance, and corroboration of the XRF logging was done using wire line logs, a combination of spectral gamma and induction conductivity logs. Detailed characteristics (abundance, grain size, shape) and chemical composition of minerals was determined by the GEUS CCSEM methodology (Frei et al, this vol.). The average weight percent TiO2 for all Ti-minerals is 62%, 60% excluding rutile. That elevated TiO2 content (>> ilmenite stoichiometric value, ca. 50 %) indicates that ilmenite experienced an iron-leaching environment. The source of the sand deposit was investigated by dating contained zircon. The results show that the likely sources of zircon are in southern Norway and southwestern Sweden with common zircon ages of ca 1100 Ma. and 1500 Ma.

Jan 1, 2005

By Tim O’Neil

Caterpillar has introduced its 5090B front shovel, to work with 40 to 70 st (36 to 63 t) trucks. The new unit replaces Cat’s 5080 hydraulic excavator. The 5090B offers more engine horsepower, higher flow, greater digging forces, higher swing torque, faster swing speed and more drawbar pull than its predecessor. It can also handle larger bucket sizes than the previous model. These improvements enhance productivity and make the 5090B a high-volume material handler for hard rock and aggregates producers.

Jan 1, 2003

By William H. Langer

Large amounts of limestone fines co-produced during the processing of crushed lime-stone may be useful in the sequestration of carbon dioxide (CO2). Accelerated weathering of limestone (AWL) is proposed as a low-tech method to capture and sequester CO2 from fossil fuel-fired power plants and other point sources such as cement manufacturing. AWL reactants are readily available, inexpensive and environmentally benign. Waste CO2 is hydrated with water to produce carbonic acid. This reacts with and is neutralized by limestone fines, thus converting CO2 gas to dissolved calcium bicarbonate. AWL waste products can be disposed of in the ocean. Feasibility requires access to an inexpensive source of limestone and to seawater, thus limiting AWL facilities to within about 10 km (6 miles) of the coastline. The majority of U.S. coastal power-generating facilities are within economical transport distance of limestone resources. AWL presents opportunities for collaborative efforts among the crushed stone industry, electrical utilities, cement manufacturers and research scientists. There is a concern that CO2 generated from human activities is contributing to climatic and environmental changes. Approximately one-third of anthropogenic CO2 emissions come from burning fossil fuels to generate electricity. Each power plant is capable of emitting several million tons of CO2 annually. A variety of other industrial processes, such as cement manufacture, oil refining, and iron and steel production, also emit large amounts of CO2. The level of atmospheric CO2 can be reduced by capturing CO2 from point-source emissions and storing or sequestering it in isolation from the atmosphere (U.S. Department of Energy, 2003). In 1999, G.H. Rau and K. Caldeira proposed a geochemistry-based method that is referred to as accelerated weathering of limestone (AWL) in a paper titled ?Accelerating carbonate dissolution to sequester carbon dioxide in the ocean ? geochemical implications.?

Jan 1, 2009

One of the most common critical areas of longwall mining in terms of ground stability are the gateroad and bleeder entries. These critical entries provide much-needed safe access for miners and allow for adequate ventilation required for dilution of hazardous airborne contaminants and must remain open during mining of a multi-panel district. This paper focuses on the stability of the longwall entries subjected to a single abutment load such as bleeders, first tailgate, and last headgate. First tailgate and last headgate are also referred to as blind headgates and tailgates. A study of a longwall district through conditions mapping, support evaluations, and numerical modeling was conducted and evaluated by researchers from the National Institute for Occupational Safety and Health (NIOSH). The condition mapping and support evaluations were performed on entries that spanned the previous five years of mining and relied on a diverse selection of supports to maintain the functionality of the entry. Numerical modeling was also conducted to evaluate various support types with further investigation and comparison to the condition mapping. The study demonstrated the importance of the abutment load decay versus distance from the gob edge, the potential for a reduction in material handling related injuries, as well as optimal usage of secondary and standing support.

Jan 7, 2020

Inn mining communities throughout the western United States, cows have always been part of the landscape as they graze on surrounding rangelands. Until recently, mining companies regarded these animals as something to be kept off their properties — especially any freshly reclaimed lands. During the last few years, though, this situation has begun to change. Today, cattle can be seen in a handful of mine settings, moving up and down the slopes of mine tailings and waste rock. These animals are being used by several companies to do some of the reclamation work once performed by large earth-moving equipment, mechanical spreaders, rippers and seed drillers. This is because cows can contour slopes more naturally and produce and spread soil nutrients in ways that tractors and ripping machines cannot.

Jan 1, 1999

By Zhenqi Cai

The ongoing Overpeck Valley Parallel Sewer Project of Bergen County Utilities Authority (BCUA), New Jersey, is a US $65 million CSO improvement program to meet a State DEP consent order by 2010. One major program component includes a total of 1.8 km (1.2 mile) long, 1,800 mm (72 in) diameter reinforced concrete pipe (RCP) installed by a Herrenknecht AVND1800AB MTBM. The alignment includes drives through 850 m (2,788 ft) of extremely soft glaciolacustrine varved clay, 980 m (3,214 ft) of loose to medium dense mixed soils containing silty sands, gravels, and boulders, and crosses under the New Jersey Turnpike, US Highway Route 46, and a CSX Railroad Intermodal Yard and a branch mainline. Two types of MTBM cutterheads are being used, one configured for the weak varved clay, and one for the mixed soil conditions. The MTBM is also equipped with a double-steering system consisting of a standard front steering joint and a second trailing steering joint to assist grade control should adequate steering not be achieved by the front primary steering in extremely weak soil conditions. This paper discusses the significant engineering aspects and challenges related to site settings, ground characterization, key MTBM features and performance, and required ground treatment.

By Malcolm Ross

Asbestos crystallizes within rock formations undergoing intense deformation characterized by folding, faulting, shearing, and dilation. Some of these conditions have prevailed during formation of the taconite iron ore deposits in the eastern Mesabi Iron Range of Minnesota. This range includes the Peter Mitchell Taconite Mine at Babbitt, Minnesota. The mine pit is over 8 miles long, up to 1 mile wide. Fifty three samples were collected from 30 sites within areas of the pit where faulting, shearing and folding occur and where fibrous minerals might occur. Eight samples from seven collecting sites contain significant amounts of ferroactinolite amphibole that is partially to completely altered to fibrous ferroactinolite. Two samples from two other sites contain ferroactinolite degraded to ropy masses of fibers consisting mostly of ferrian sepiolite as defined by X-ray diffraction and TEM and SEM X-ray spectral analysis. Samples from five other sites contain unaltered amphiboles, however some of these samples also contain a very small number of fiber bundles composed of mixtures of grunerite, ferroactinolite, and ferrian sepiolite. It is proposed that the alteration of the amphiboles was caused by reaction with water-rich acidic fluids that moved through the mine faults and shear zones. The fibrous amphiboles and ferrian sepiolite collected at the Peter Mitchell Mine composes a tiny fraction of one percent of the total rock mass of this taconite deposit; an even a smaller amount of these mineral fragments enter the ambient air during mining and milling. These fibrous minerals thus do not present a significant health hazard to the miners nor to those non-occupationally exposed. No asbestos of any type was found in the mine pit. © 2007 Elsevier Inc. All rights reserved. Keywords: Taconite; Asbestos; Amphibole; Reserve mining; Tailings; Mesabi iron range; Mineral fibers

Jan 1, 2007

By F. Mielli

Camera systems and video surveillance are usually associated with people and asset protection. However, they can be applied in a mine environment beyond conventional surveillance: For process monitoring, collision avoidance, sizing, flotation cells, conveying systems, blasting, objects and people tracking, thermal profile, and to automatically identify equipment that is missing parts,. Image and video solutions can be driven by better integration of powerful video analytics and cameras systems in automation tools such as process controllers and supervision systems.

Feb 27, 2013