Search Documents

By T. Fraszczak, U. A. Peuker, T. Mütze, O. Ortlepp

Dolomite is a calcium carbonate sedimentary rock that can be found all over the world. In its calcined form it is employed for water treatment or as an additive in iron production. Calcined dolomite is produced at the Wünschendorfer Dolomitwerk GmbH in shaft furnaces (kilns). Because of an expansion of the mined deposit, significantly higher extraction costs were expected. Therefore, the existing upgrading processes for the kiln stone fraction had to be adapted and improved. This paper presents a process optimisation which allows for an increase of the yield of calcined dolomite by 10 % due to a redesign of the crusher circuit and by an additional 5 % due to a comprehensive characterisation of the kiln stone fraction itself. Here the interdependency between the pressure drop in the furnace during calcination and the size distribution of furnace stones was used to increase the amount of fine size fractions in the furnace feed without deterioration of the calcination process. Keywords: Dolomite, crushing circuits, kiln stone production, flowability, calcination

Jan 1, 2020

By X. H. Li, Q. Zhang, X. Fei

Bauxite residue known as red mud (RM) is a by-product produced in massive quantities during alumina production by the Bayer process with a utilisation rate of less than 5%. A large amount of RM accumulated and produced continuously has had a seriously adverse impact on the surrounding ecological environment. The application of RM in building materials is considered to be the most effective and thorough way to make RM harmless and recycle resources for the reason that adding RM to concrete as a mineral admixture could not only consume a lot of RM, but also save cement and other energy-consuming industrial products. In this paper, the adaptability to cement and aggregate of RM was studied. The results showed that the compressive strength and flexural strength of concrete using ordinary Portland cement, slag Portland cement or fly ash Portland cement as cementing material showed different trends with the increase of the amount of RM. The influence rules of RM on the compressive strength of Portland cement, slag Portland cement and fly ash Portland cement concrete were similar, whether for silicate aggregate or carbonate aggregate. RM has a negative correlation to the flexural strength of silicate aggregate-ordinary Portland cement concrete, but a positive correlation to silicate aggregate-slag Portland cement, silicate aggregate-fly ash Portland Cement. RM promoted the formation of calcium carbonate crystals and inhibited the formation of ettringite and calcium hydroxide crystals in the matrix while ordinary Portland cement, Portland cement and fly ash Portland cement were used as cementing materials. This study provided support for the use of RM in concrete, the reduction of solid waste storage, and the saving of high energy consumption cement as well. Keywords: Red mud, cement, aggregate, adaptability, mechanical properties, mineral composition

Jan 1, 2020

By J. H. deur Potgieter

This paper, 'A review of the biological treatment of cyanide-bearing waste water' discusses the necessity for the treatment of cyanide-bearing waste water with a view to the avoidance of environmental pollution, and the limitations of the available chemical and physical processes are referred to briefly. The sources of cyanide-bearing waste waters are mentioned. The mechanisms of production and utilization of cyanide by fungi and bacteria are discussed. The work done in connection with the biological removal and destruction of cyanide is summarized, the successes achieved are described, and the relevant processes are listed. In conclusion, some advantages of biological processes for the removal of cyanide are mentioned.

Jan 1, 1991

1. Recent books D. K. Hsiao, D. S. Kerr, and S. E. Madnick. Computer security. New York, Academic Press, 1979.276 pp. $18. W. C. J. van Rensburg and S. Bambrick. Economics of the world's mineral industries. Isando, McGrawHill, 1979. R18,95. Soviet metallurgical research 1973-1977. Vo!. 1. Subject index and author index (1963-1972). Vo!. 2. Chronological listing of titles with full bibliographical information (1960-1972). London, Scientific Information Consultants Limited (661 Finchley Road, London NW2 2HN). £24 per set. W. Hoosen. Miners' dictionary. London, Institution of Mining and Metallurgy, 1979. (Reprint.) £11 (£9 for members). G. J. Pitt and G. R. Millward. Coal and modern coalprocessing: an introduction. New York, Academic Press, 1979. 224 pp. $18. D. Stephenson. Rockfill in hydraulic engineering. Amsterdam, Elsevier, 1979. 228 pp. U.S. $45, D.fl.90. 2. NIM reports Report no. 2015 The preparation of synthetic standards for use in instrumental neutron-activation analysis. Report no. 2029 The commissioning of a 5 kW inductively coupled plasma unit for use with a 3,4-metre Ebert spectrograph. Report no. 2032 The Cancer Project: a summary of the computer-aided operation of a 48 MV.A ferrochromium furnace. Report no. 2036 The determination of thallium in ores, concentrates, and metals. Report no. 2040 A solid-state constant-current power unit for the magnetic analyser of the MS702R mass spectrometer. Report no. 2044 The separation and determination of anions by ion chromatography. Computer congress In October 1980, Japan and Australia are hosting the 8th World Computer Congress. This Congress is a triennial event conducted under the sponsorship of the International Federation for Information Processing. INFACON 80 The Second International Ferro-Alloys Congress, organized by IPFEO (Institute of Western European Ferro-alloy Producers), is to be held in Lausanne, Switzerland, on 13th to 16th October, 1980.

Jan 1, 1980

By L. Kühnel, H. Lieberwirth

Confined bed comminution in High Pressure Grinding Rollers (HPGR) and Vertical Roller Mills (VRM) is gaining substantial attention in many applications. Previously used mainly for milling coal or construction materials, HPGR and VRM have started to complement or even replace tumbling mills in ore beneficiation. Materials like coal or clinker are relatively homogenous, however, in comparison to metal ores and wall rocks. This characteristic poses a new challenge to the confined bed comminution but also an opportunity. Fuerstenau and Abouzeid have investigated the selectivity in comminution of a mixture of particles of different strength in a particle bed. The median particle size and particle size distribution (PSD) of the two constituents used were kept constant. Only the proportion of the two constituents was modified. The competence of a material is, however, also a function of particle size. Smaller particles tend to be more competent than larger ones of the same material. If selective comminution is applied on ores, this size influence has to be understood. The paper presents research results on this topic based on experimental investigations with model materials as well as with natural particles, which were stressed in a piston-die press. It appeared that the comminution result depends substantially on the material characteristics and the composition of the mixture. Conclusions will be drawn for the application in future applications of selective comminution in mineral processing. Keywords: Confined bed comminution, HPGR, VRM, piston die press, particle size

Jan 1, 2020

THE THIRD INTERNATIONAL GEOCHEMICAL EXPLORATION SYMPOSIUM (Summary Account) This Symposium, co-sponsored by the Canadian Institute of Mining and Metallurgy and the Society of Economic Geologists, was held in Toronto, Canada in April, 1970. Over 700 delegates attended from 26 countries. Ninety papers were presented at the symposium and another 18 papers were read by title. The programme included: An Opening Session, Five General Sessions, a session on Remote Sensing Methods, a session on Geochemical Prospecting for Petroleum and Natural Gas, a session on Primary Halos and Lithogeochemical Methods, and a session on Statistics and Evaluation of Geochemical Data. The delegates were welcomed by Dr J. M. Harrison, President of the Canadian Institute of Mining and Metallurgy and Dr C. H. Smith, Regional Vice-President, North America of the Society of Economic Geologists. Dr D. R. Derry of Toronto delivered the opening address to the Symposium entitled 'Geochemistry-the link between ore genesis and exploration'. Dr Derry considered the various hypotheses on the origin of economic mineral deposits and expressed his belief that the next ten years will show evidence of an increased proportion of ore bodies that owe their origin, at some stage in time, to supergene agencies. He stressed that 'there are no sharp divisions between processes that form and destroy ore bodies at or near surface and those that form or destroy them at a depth of 20 kilometres in the earth's crust. The more we understand about the migration and concentration of metals the more accurately we can apply this knowledge to searching for unknown concentrations, whether at rock surface or at depth. To learn more about these processes of ore genesis we must rely on geochemical studies co-ordinated with field observations'. The five general sessions included accounts of progress in geochemical prospecting in different countries of the world, case histories describing the application of soil, stream sediment, geobotanical and biogeochemical techniques, papers on the behaviour of different elements under varied environmental conditions, discussions on analytical methods and the use of stable isotopes in mineral exploration. It is anticipated that the proceedings of the Symposium will be published late in 1970 or early in 1971 as a Special Volume of The Canadian Institute of Mining and Metallurgy. All registrants at the Symposium will receive a copy of this publication and copies will be available for purchase. At a special meeting called during the Symposium, charter members of the Association of Exploration Geochemists approved a constitution and elected an interim Council which will organize procedure and formulate policy during the coming year. The interim president of the Association is J. Alan Coope, Newmont Mining Corporation of Canada Limited, Toronto, Canada. More information on the constitution and membership in the Association will be distributed to learned societies and technical magazines in the near future. Membership will be open to exploration geochemists in all countries of the world. SOUTH AFRICAN COUNCIL FOR PROFESSIONAL ENGINEERS Report on Registration The Professional Engineers Act (Act 81 of 1968) came into force on the 14th February, 1969. At the time it was recognised that the success of the Act would depend in large measure on the extent to which engineers in South Africa would become registered professional engineers in terms of the provisions of the Act. The promulgation of the Act and its provisions relevant to registration were the subject of considerable publicity during 1969. This has resulted in a rate of application for registration far beyond the capacity of the very active committees set up for this purpose by the South African Council for Professional Engineers (SACPE). To give some idea of the task before these committees and before SACPE itself, which must ratify each case,

NOTICE The Institute has received requests for copies of Uranium in South Africa', Vols. 1 and 2, but is unable to supply, as all copies have been sold out. If any members have copies they wish to dispose of it would be appreciated if they would contact the Secretary, P.O. Box 1183, Johannesburg. Telephone 834-1271.

By C. O. Esterhuysen, J. P. Deetlefs, C. A. Wessels

The productivity indices of the Republic of South Africa compare poorly with those of its competitors in the rest of the world. The theory of productivity is relatively simple, and various models are available to demonstrate this. The problem is how to apply the theory in practice and to convert it into a practical management system that will guarantee results. The secret lies in a management approach that aims at a continuous improvement in achievement and that involves the entire work force down to the lowest level in the process. Good management systems ensuring the necessary attention to, among others, management by objectives, finance, personnel, maintenance, planning, and control are a prerequisite for continued improvement and staff involvement. The net result of such an approach is described by the term performance management, which encompasses the total integration of al a company's management systems.

Jan 1, 1989

By H. -U. Lim, C. -H. Kim

The sixth underground pumped powerhouse cavern is under construction now in Korea. For the stability analysis of the five underground powerhouses, finite element method was used. For this analysis, in-situ rock stresses were measured by overcoring method and horizontal to vertical stress ratio was calculated 1.07-1.32 at four sites. Rock mass strength and elasticity were assumed from intact rock properties. The ratio of elasticity of rock mass was 0.16-0.55 of intact rock core elasticity. In general, elasto-plasticity with Mohr-Coulomb failure criterion was applied and the input cohesion and internal friction angle were approximately 0.12-0.22, 0.6-0.87 of intact rock strength parameters, respectively. Der sechste Untergrund-gepumpt-Powerhouse-Cavern ist jetzt im Bau in Korea. Für die vergan-gene Stabilitätsanalyse des fünf unterirdischen Powerhouses in Gebrauch wurde ein begrenztess Elementsmethode benutzt. Für die Analyse wurden In-Situ Felsenspannungen von overcoring Methode gemessen und Horizontale zu senkrechtem Spannungsverhältnis waren als 1.07-1.32 an vier Stellen kalkuliert. Felsenmassenkraft und Elastizität wurden von unversehrtem Felsenei-gentümern angenommen. Das Verhältnis der Elastizität von Felsenmasse war 0.16-0.55 von un-versehrter Felsenkernelastizität. Im allgemeinen wurde Elasto-Plasticity mit Ausfallskriterium des Mohr-Coulombs verwendet. Die Eingabebindekraft und die innere Reibungswinkel waren unge-fähr 0.12-0.22, 0.6-0.87 von unversehrtem Felsenkraftsparametern, jeweilig. En Coree, la sixieme centrale souterraine de la pompe d'accumulation dans la caverne est en construction. La methode d'element fini a ete utilisee pour analyser la stabilite de cinq dernieres centrales en service. Dans cette analyse, la reaction de la roche sur place etait mesuree par la methode d'overcoring et celle du rapport horizontal-vertical etait calculee de 1.07-1.32 en quatre places. L'intensite et l'elasticite de la masse de roche ont ete estimees de la roche intacte. Quant a l'elastic-ite, sa masse de roche etait 0.16-0.55 fois que celle de la roche intacte. En general, elasto-plasticite avec le critere de defaut Mohr-Coulomb etait utilisee et sa cohesion d'energie et son angle de friction interieure etaient supposees respectivement 0.12-0.22, 0.6-0.87 fois que la parametre de l'intensite de roche intacte.

Jan 1, 2003

By A. Dienenthal

"The casthouse floor has always been one of the most dangerous working places on a blast furnace or a ferro-alloy/nonferrous furnace. Apart from working in an atmosphere including toxic gases, fumes, and dust, the workers have to perform hard and heavy manual work close to runners and ladles filled with hot liquid metal and slag.Before the invention and installation of tapping equipment the tap-holes were opened and closed manually. Opening was done by means of steel bars and sledgehammers, whereas the tap-hole was closed by repeatedly ramming small amounts of clay or refractory material into the tap-hole, again with the help of long, heavy bars. In addition, on blast furnaces the blast had to be stopped, since it was impossible to close the tap-hole properly against the blast furnace pressure. This stoppage of the blast resulted in regular losses of production. Around 1900 a major change in technology occurred. Samuel W. Vaughen, superintendent of the blast furnace department of the Cambria Iron company at Johnstown, Pennsylvania (USA), invented the first clay gun in 1895 (Wiley, 1896) (Figure 1)."

Jan 1, 2014

By S. Langea, H. Lieberwirth

Impact crushers are common machines in comminution plants. Their high size-reduction ratio and relatively simple design, make them a preferred tool even when subjected to harsh wear, and producing a large quantity of fines in some applications. Until now the alignment of the operational parameters was an operator’s responsibility. Due to the random process characteristic this is mostly done based on empirical values and sensor data, such as power consumption. This paper describes a new approach for online process monitoring of the horizontal-shaft-impact crusher. The application of robust, low-cost acceleration sensors enables the permanent observation of the process characteristics. The operational and evaluation methods are determined on the basis of experiments. Subsequently the recorded measurements are analysed in regards of throughput, rotational speed and product particle size distribution. Occurring signal characteristics are described based on physical and technical principles. The measured data of the acceleration sensors at varying operation conditions provide insight in the course of process. The accurate utilisation yields the determination of the preferential process conditions providing the best balance between the pros and cons of an impact crusher. Both the experimental method and the data processing is discussed from a scientific perspective, displaying a completely new approach for the operation of impact crushers. Keywords: Impact crusher, acceleration sensors, data processing, particle size

Jan 1, 2020

1. New books Specialty steels and hard materials, edited by N. R. Comins and J. B. Clark. Oxford, Pergamon, 1983.482 pp. Hardcover £55.50. Papers presented at an international conference on advances in flow measurement techniques, edited by H. S. Stephens and B. Jarvis. BHRA Fluid Engineering (Cranfield, Bedford, MK43 OAJ, England), 1982. £36. Papers presented at Fourth European Conference on Mixing, edited by H. S. Stephens and D. Goodes. BHRA Fluid Engineering (Cranfield, Bedford, MK43 OAJ, England), 1982. £36. Papers presented at an international conference on hydrocyclones, edited by H. S. Stephens and G. Priestley. BHRA Fluid Engineering (Cranfield, Bedford, MK43, OAJ, England), 1982. 248 pp. £27. Controlled atmospheres for heat treatment, by R. Nemenyi. Oxford, Pergamon, 1983. 225 pp. Hardcover 20, flexicover £7.50. Electrochemical techniques in corrosion testing and research, edited by J. S. Scully. Oxford, Pergamon, 1983. 150 pp. Flexicover £9.45 2. Book reviews Off highway truck haulage, by the Newman Combined Group. Parkvine (Victoria), Australasian Institute of Mining and Metanurgy, 1982. Reviewer: B. J. Vorster Elsevier's mineral and rock table, compiled by P. Lof. Reviewer: A. Wedepohl Field geologists' manual, by B. A. Berkman. Monograph Series No. 9, Australasian Institute of Mining and Metanurgy, 1982.295 pp. Reviewer: R. A. G. Cuipers 3. Mintek reports Report M56 A computer programme for the evaluation of process routes in the production of ferrochromium. Report M61 An atomic-absorption programme for the Apple 11 Plus computer. Report M63 A general-purpose data logger. Report M65 A preliminary survey of the corrosivity of water in gold mines. Report M66 A review of corrosion inhibitors: theory and practice. Report M67 The determination of total cyanide in solutions containing uranium and gold. Report M68 The suitability of Doppler flowmeters for use in the minerals-processing industry. Report M70 The preparation and certification of two reference materials of South African manganese ore. Report M78 A n evaluation of the Leeds laboratory-scale flotation cell. Report M79 The determination, by X-ray-fluorescence spectrometry, of gold and uranium on resin. Report M80 The installation and commissioning of a Siemens SRS200 sequential X-ray-fluorescence spectrometer. Report M81 The application of the inductively coupled plasma system to the simultaneous determination of precious metals. Open-pit and strip mines The South African Institute of Mining and Metallurgy and the Mining Alumni Society of the University of Pretoria are organizing an International Conference on The Planning and Operation of Open Pit and Strip Mines in Pretoria from 9th to 13th April, 1984. Other Institutes co-sponsoring the Conference are The Canadian Institute of Mining and Metallurgy, The Institution of Mining and Metallurgy, and The Society of Mining Engineers of AIME.

Jan 1, 1983

By J. T. M. Amphlett, C. A. Sharrad, M. D. Ogden, R. I. Foster

"A renewed interest in nuclear power around the world in order to reduce greenhouse gas emissions is going to increase demand for uranium as fuel. This will result in more uranium being mined, which will in turn increase associated environmental pressures, such as fresh water use. A move to lower quality waters containing impurities such as chloride would help alleviate these pressures. In this work, we determined the uptake characteristics of weakly basic anion exchange resin Ps-EDA towards uranium from saline solutions in a dynamic flow column. Breakthrough curves were produced, with suppression of uptake being observed for chloride concentrations above 5 g L-1. Calculated resin saturation capacities at zero and 5 g L-1 chloride are comparable with literature values for strong-base anion exchange resins, and exceed those published for weak-base resins up to 20 g L-1 chloride. Data has been fitted to multiple breakthrough models, with the modified dose-response model most effectively predicting uranium recovery. The results show that the ethylenediamine functionality could be suitable for use in future uranium processing flow sheets where a high-saline lixiviant is used. IntroductionIon exchange (IX) is a key technology in the uranium mining industry and is well established for the extraction of uranium from both acidic and alkaline leach liquors (Edwards and Oliver, 2000). It was first employed in 1952 at the West Rand mine in South Africa (Ford, 1993; Taylor, 2016). H2SO4 and Na2CO3 are the most commonly employed lixiviants used to solubilize uranium in acidic and alkaline leach conditions respectively. The chemistry of these systems causes uranium to form anionic sulphate or carbonate complexes, which can be taken advantage of by anion exchange resins.Another major technology for the extraction and purification of uranium from leach liquors is solvent extraction (SX). This technique involves the extraction of uranium from the aqueous phase into an immiscible organic layer. Although this is a commonly used method, there are major drawbacks to it, including the use of large volumes of flammable solvents, solvent loss, phase disengagement, third phase formation, and the production of problematic degradation products (Veliscek-Carolan, 2016). These problems can be circumvented through the use of IX resins."

Dec 1, 2018

By DeVerle P. Harris, David E. Euresty

"Potential metal supply refers to metals to be produced from as yet unknown deposits. Naturally, to measure potential supply requires, among other things, inference to the number of deposits, their tonnage, and their grade Thus, probability distributions were constructed for each 400-square mile cell in Northern Sonora, Mexico. A computer system was developed that simulated the occurrence of deposits for each cell, exploration for the deposits, and their exploitation. Evaluation was performed for each deposit by discounted cash flow analysis.An objective of this study was to explore the effect of the transportation network and required road or railroad construction upon potential supply. Consequently, the evaluation system was designed to consider the spatial location of a simulated deposit to the existing transportation network and the market destination. The construction of linkages to connect the deposit to existing transportation arteries as well as the carrying of the concentrates to the intended market were simulated. in terms of cost. The selection of the path took into account the existing terrain. This was done by digitizing topographical maps and representing the topography of the area by an orthogonal grid of elevations. The optimum route was selected by dynamic programming, meeting a prescribed gradient constraint. The potential supply of each cell was determined, allowing for the infrastructure effect."

Jan 1, 2014

By E. Matinde

Human beings have been dependent on metals and alloys for livelihoods since time immemorial. In fact, there is irrefutable evidence that successful ancient civilizations achieved supremacy over their environments through the mastery of metals and alloys (Miller, 1995; Mtetwa, 2022). Over time, metals and alloys have evolved to become ubiquitous engineering materials indispensable to mankind, with applications in industrial and residential infrastructure, agriculture, energy generation and storage, transportation and communication systems, and manufacturing, among others (Elshkaki et al., 2018; Watari et al., 2021). Population growth, technological developments, and increase in urbanization and industrialization are all intricately linked to the intensity of use of metals and alloys. With up to 5 billion people estimated to live in urban areas by 2030 (Armstrong, 2009), the demand for metals and alloys will inevitably increase in order to satisfy the increased demand for infrastructure, machinery, and other human needs (Elshkaki et al., 2018; Watari et al., 2021). According to LePan (2022), urbanization and growth of mega-cities will increase the demand for metals and alloys, such as nickel, steel, aluminium, and copper by 116%, 50%, 57%, and 26%, respectively, between 2019 and 2035. Naturally, the production of metals and alloys from natural ores, secondary resources, and/or a combination of both, to meet this increased demand will invariably lead to the increase in generation of deleterious emissions in the form of wastes. In fact, mining and metallurgical wastes currently constitute the world’s largest anthropogenic streams by mass, often containing a high concentration of elements and compounds that can cause potential damage to natural ecosystems and humans (Hudson-Edwards et al., 2011; Lottermoser, 2011; Matinde et al., 2018; Seetharaman et al., 2022). Obviously, society’s heavy reliance on new mineral resources to drive the emerging energy transition entails that the legacy of these waste streams will continue unabated for the near-foreseeable future. The scarcity of high-grade mineral reserves, coupled with deliberate efforts to solve the anthropogenic circularity conundrum, therefore introduces a high level of urgency in the metal extraction industry to develop nascent and more eco-friendly processes and technologies. Integrating circular economy principles based on intentional configurations of circular industrial ecosystems in order to maintain the value of materials and resources in the economy for as long as possible is widely accepted as a practical approach to mitigating the negative externalities imposed by

Sep 1, 2024

By D. Sethuram, P. G. Koppad, S. Iyengar, R. Shobha

TiB2 and CeO2 particle-reinforced Al6061 hybrid composites were manufactured using stir casting and hot rolling techniques. The base alloy and composites were hot-rolled at 500ºC and a 50% reduction was achieved through 12 passes. The effect of varying TiB2 and CeO2 particle additions on the microstructure and mechanical properties of the Al6061 matrix was studied. Scanning electron microscopy showed uniform dispersion of both the reinforcements, with good interfacial bonding. Microhardness and tensile properties like yield and tensile strength were found to be higher for hybrid composite with 2.5% TiB2 and 2.5% CeO2 compared to Al6061 alloy and other hybrid composites. The increased tensile strength is attributed to good dispersion and interfacial bonding between the particles and Al6061 matrix. Fracture analysis using a scanning electron microscope revealed ductile fracture for the Al6061 alloy and mixed characteristics of ductile-brittle fracture for hybrid composites

Oct 1, 2021

By C. J. Liebenberg

This paper focuses on the application of ion exchange technology for the recovery of copper from a leach solution originating from a heap bioleach in which base metals are leached from a low-grade ore that bears platinum group metals. Screening tests indicated that Dow XUS43605 has high selectivity for copper over the other metals in the solution, namely nickel, iron, cobalt, zinc, manganese, and aluminium. Batch adsorption kinetic experiments showed that copper adsorption equilibrium is attained at a fast rate. The kinetics of adsorption increased as the temperature was increased from 25°C to 60°C due to the decrease in solution viscosity and the subsequent improved intra-particle mass diffusion. Single-component Langmuir and Freundlich isotherm models were fitted to the batch copper adsorption equilibrium data, and a maximum copper capacity of 26 g/l was observed for Dow XUS43605. The effects of flow rate, temperature, pH, and initial metal concentration on the dynamic recovery of copper were investigated in fixed-bed columns, and it was determined that temperature and flow rate had the most significant impacts on the loading of copper on the resin at copper breakthrough. A 36% increase in copper loading at breakthrough was observed when the temperature was increased from 25°C to 60°C. Finally, it was determined that a split elution is possible by using different concentrations of H2S04 to first elute co-loaded nickel from the resin, followed by the elution of copper.

Jan 1, 2013

By N. Theron, R. F. Meeser

The global emphasis on conserving energy resources has led to the adoption of hybrid power systems in vehicles. Optimally applied, hybrid systems can save up to 40% on fuel costs. To optimally manage a hybrid vehicle's energy flow it is necessary to know, in real time, all the energy requirements to complete a given route. The energy consumption depends mainly on the vehicle mass, speed profile, and route topography. Of these, the topographic profile is the one factor that is only route-dependent and not influenced by the vehicle or driving styles. The heading vs. distance profile is also an example of a route characteristic not influenced by the vehicle or driving style. In this study the topographic and heading profiles are used to identify routes, and are easily measured by means of digital barometric pressure and compass sensors. Correlations between the current route and previously travelled/stored routes are performed based on their topographic and heading profiles in a point-by-point manner. Above-ground tests were first performed using a road vehicle and six routes to evaluate the system. The system consistently and correctly identified a 20 km route within the first 4 km. It also proved to function correctly in underground tests through the implementation of an instrumented hand-held surveyor's wheel. This system finds direct practical application in optimizing the energy management of an underground hybrid locomotive used by the mining industry in South Africa, but can also be of benefit in applications where route identification is required and using GPS is not feasible.

Jan 26, 2023

The September General Meeting of the Institute was held in Kelvin House, Johannesburg, on 16th September, 1970, at 3.00 p.m. Mr V. C. Robinson (President) was in the Chair. There were also present one hundred and eighteen Fellows, including Dr J. M. Bereza, H. P. Carlisle, R. J. C. Goode, Dr J. P. Hugo, P. Lambooy, Prof R. P. Plewman, W. W. Malan, Dr J. T. McIntyre, Dr M. D. G. Salamon, L. W. P. Van den Bosch, P. A. von Wielligh (Council Members), A. Bain, G. P. Bennet, D. L. Carson, G. L. H. Diering, M. E. E. Douglas, F. A. B. Fouche, R. Fourie, A. R. C. Fowler, E. B. Gordon, J. S. Hay, G. H. Henderson, S. D. Hill, A. C. Hofmeyr, J. M. Jacobs, A. F. Lee, D. G. Malan, L. J. Prince, W. G. Pyne-Mercier, A. H. Mokken, Dr W. S. Rapson, R. R. Richardson, H. V. Solomon, C. G. Sowry, G. G. Stanley, G. R. Still, D. L. Starkey, D. L. Taylor, E. W. Thiel, I. E. Van Aswegan, M. van Ryneve1d Steyn, N. B. Vinson, H. Wheeler, Dr A. Whillier, R. A .Wilson, C. F. Ziervogel. Forty-two Members including R. C. Bertram, F. Collier, G. C. Currie, O. Davel, J. M. Gosnell, A. Hazell, Dr N. C. Joughin, F. Kleinschmidt, D. Love, R. B. Macgillivray, D. Mather, R. D. R. Munro, R. S. Pearson, J. J. Peisl, T. J. Pole, A. J. Rossouw, R. G. B. Skirving, G. S. Schwartz, K. Stee1e, H. A. G. Slater, A. Taylor, B. A. Thomas, P. L. Vaughan, D. T. Watt, W. Wilson. Nineteen Associates including R. K. Briggs, S. I. Du Preez, P. G. Gaylard, P. H. Hartslief, W. M. Mackay, A. D. Ross. Three Students: V. S. Care, R. J. Drummond, P. J. Pretorius. Thirty-one Visitors including C. P. S. Barnard, D. W. Bosch, M. Bain G. L. Brown, G. D. Behrens, C. Coetzer, D. M. Gilbart-Smith, R. L. Man, Dr G. J. Stander, M. W. L. Steinobel, R. H. E. Thorpe, T. D. van Wyk, P. H. van Zyl, E. Vereecken, J. J. H. Viljoen. Secretary, D. C. Visser. Total present: 215. OBITUARIES The President: "It is my sad duty to announce the death of the following: Bruce Donaldson Crawford, Fellow, who joined the Institute in 1951 and passed away on 29th April, 1970. Donald Joseph Powrie, Life Fellow, who joined the Institute in 1935 and passed away on 22nd July, 1970. As a mark of respect to the memory of the deceased and in sympathy with the bereaved I would ask you all to rise and observe a few moments' silence." MEMBERSHIP The President: "I have much pleasure in announcing that the names of the under-mentioned candidates, having been published in accordance with By-Law 5.2.2, Council has elected them to membership of the Institute in the following grades: Associate: WiIliam Norman Carter. Students: Roman Michael Dabrowski, Sean George Dean Eaton, Alan Philip Stonham Howard, Anton du Preez Roos, Richard Harold Tourle. MEMBERS TRANSFERRED TO A HIGHER GRADE From Graduate to Member: Terrance Alexander Ward. From Associate to Member: Bernard Andre Thomas. "I welcome the newly elected members to the Institute and congratulate the members who had been transferred to a higher grade." CO-OPTION The President: "I wish to advise members that, in terms of clause 3.9 of the Constitution, Mc. H. P. Carlisle had been co-opted to serve on Council." PAPERS FOR PRESENTATION The President: "We have two papers today, and I am first going to call on Dr Stander the Head of the Water Division of the C.S.I.R., who IS well known to many of you for his work and talks on pollution, who has had more than a little to do with this industry, and who has been I would say, of the greatest possible assistance to the mining industry in overcoming the problems of pollution which are so prevalent in industry of this nature. He, Mr Henzen and Mr Funke have written this paper, 'The disposal of polluted effluents from mining, metallurgical and metal-finishing industries, their effects on receiving water and remedial measures.' This is the Water Year, as you know, and it is most appropriate that we should have such an authority to talk to us on this very important topic. I now have much pleasure in asking Dr Stander to introduce his paper." After the presentation of the paper the President said, "Gentlemen, I am sure that you would like me on your behalf, to thank Dr Stander very sincerely for a paper which I think has enabled us to get a completely new slant on the Water Year. There are many people who have put their finger on this campaign and said, it is all a gimmick. There are others-I suppose notably some of the bridge clubs which operate on week-day afternoons in Parkview-who seem to think that this is a quick way of getting early rain. Of course, it is not. This is a most important paper which we have had given to us this afternoon. You probably found it here when you arrived and have not read it-I was very lucky to be able to read it last night, and there is an awful lot of meat in it. For as long as I have been associated with mining in any way, there has been a problem of polluted effluent-of effluents carrying a mineral load from mining, and I think Dr Stander is absolutely right-and, of course, the Commission is right when they say that this is not merely the problem of mine management or mine owners-this is a problem which affects every single human being in this country.

By G. van Aswegen, J. D. Bosman

Gold bearing deposits in the Witwatersrand consist predominantly of narrow tabular conglomerates with quartzite host rock. Extensive mining of these deposits at depth results in significant stresses being induced in the periphery of the tabular excavations. Where remnant pillars are created excessive stresses have resulted in the dynamic failure of the abutments. At the Hartebeestfontein Mine four brittle shear zones have recently been exposed and investigated. For most part, they represent abutment failure into the weaker hangingwall strata, striking parallel to the abutment, dipping towards the stope, with a sense of displacement consistent with closure of the stope from above. These shear zones are similar to those described in various publications by Ortlepp2: they are essentially brittle shear zones characterised by the presence of very finely comminuted ‘rock flour’ on an obviously freshly sheared surface. The angle between the shear zone wall and extension fractures indicate the sense of shear and the intersection of the extension fractures with the shear zone walls define a strong lineation normal to the direction of slip. It is suggested that these structures are referred to as ‘mining induced dynamic brittle shears’. Les gisements d’or du Witwatersrand consistent principalement de conglomérats tabulaires peu épais contenus dans une quartzite mère. Une exploitation poussée de ces gisements en profondeur a pour résultat l’apparition d’importantes contraintes induites à la périphérie des excavations tabulaires. Là où des piliers restants sont créés, des contraintes excessives ont eu pour résultat une rupture dynamique des appuis. Dans la Mine d’Hartebeestfontein, quatre zones fragiles de cisaillement ont été récemment exposées et étudiées. Dans la plupart des cas, elles représentent une rupture des appuis dans les strates moins solides de la paroi suspendue, orientée parallèlement à l’appui, inclinée en direction du chantier d’abattage avec une direction de mouvement consistante avec l’affaissement du toit de la galerie d’abattage. Ces zones de cisaillement sont similaires à celles décrites par Ortlepp2 dans diverses publications: Ce sont essentiellement des zones cisaillement fragiles caractérisées par la présence de « farine de roche » très finement réduite sur une surface évidemment fraîchement cisaillée. L’angle entre la paroi de la zone de cisaillement et les fractures de tension indiquent le sens du cisaillement et l’intersection des fractures de tension avec les parois de la zone de cisaillement définit une forte délinéation perpendiculaire à la direction du glissement. Il est suggéré que l’on se réfère à de telles structures comme des « cisaillements dynamiques fragiles induits par l‘exploitation ». Goldablagerungen im Witwatersrand bestehen überwiegend aus schmalen tabularen Konglomeraten mit Quarzitwirtgestein. Der umfangreiche Abbau dieser Ablagerungen in der Tiefe resultiert in signifikanten Drücken, die auf die Peripherie der tabularen Aushöhlungen wirken. Wo Restpfeiler hergestellt wurden, resultierten exzessive Drücke im dynamischen Versagen der Auflager. In der Hartebeestfontein Grube wurden kürzlich vier spröde Scherzonen freigelegt und untersucht. Zum größten Teil representieren sie Auflagerversagen im Stratum der schwächeren Stollenfirste, parallel zum Auflager verlaufend, in Richtung Abbaustelle abfallend, mit einem gewissen Grad an Verschiebung konsistent mit der Schliessung der Strosse von oben. Diese Scherzonen sind jenen ähnlich, die in den verschiedenen Publikationen von Ortlepp2 beschrieben werden: sie sind im Wesentlichen spröde Scherzonen, charakterisiert durch das Vorhandensein des sehr fein pulverisierten „Gesteinsmehls“ auf einer offensichtlich frisch abgescherten Oberfläche. Der Winkel zwischen der Scherzonenwand und den Bruchverlängerungen deutet die Richtung der Scherung an und die Kreuzung der Bruchverlängerungen mit der Abscherzone grenzt sich gegen eine starke Lineation normal zur Richtung der Lehne ab. Es wird vorgeschlagen, daß diese Strukturen als `vom Abbau verursachte dynamisch spröde Scherungen’ bezeichnet werden.

Jan 1, 2003