Search Documents

By D. R. Tesarik, F. M. Jones, J. B. Seymour

As part of safety and stability studies at three underground mines in the United States, researchers installed earth pressure cells and embedment strain gauges in cemented rockfill to measure stress and strain changes as mining progressed and the rockfill was loaded. Data from these instruments were used to calculate the in situ modulus of the rockfill for two of the mines. A three-dimensional numerical model of a cemented rockfill cap was validated with data from extensometers anchored in the mine roof and sill; this model was then used to estimate deformation modulus at the third mine because the earth pressure cells and embedment strain gauges recorded negligible changes. Rockfill binder used at these mines ranged from 4 to 8 per cent of the dry components by weight, the water-to-cement ratio was from 0.42 to1.0, and the largest aggregate size in the three mixes ranged from 5 to12 cm (2 to 4.7 in). The range of the calculated in situ deformation modulus values was large, but as expected, it was bracketed by modulus values for cemented tailings and roller-compacted concrete with similar cement contents and water-to-cement ratios. Dans le cadre d’études sur la sécurité et la stabilité de trois mines souterraines situées aux États-Unis, les chercheurs ont installé des palpeurs de pression des terres et des extensomètres d’encastrement dans les remblais cimentés afin de mesurer les variations relatives à l’effort et à la déformation des terrains durant l’exploitation minière et le chargement du remblai. Les données recueillies à l’aide de ces instruments ont servi au calcul du module in situ du remblai dans deux de ces mines. Le modèle numérique tridimensionnel de la semelle d’un remblai cimenté a été validé à partir des données recueillies par les extensomètres ancrés dans la voûte et dans la semelle de ces mines; ce modèle a ensuite été utilisé pour estimer le module de déformation à la troisième mine, étant donné que les palpeurs de pression des terres et les tensiomètres enfouis avaient relevés des variations négligeables. La matière d’agrégation de l’enrochement utilisée dans ces mines comportait entre 4 % et 8 % des composantes sèches par poids; le rapport eau-ciment se situait entre 0,42 et 1,0; et la taille des agrégats les plus gros dans ces trois mélanges était de 5 cm à 12 cm (2 po à 4,7 po). L’écart entre les valeurs calculées des modules de déformation in situ était grand, mais comme on s’y attendait, cet écart a été compensé par les valeurs modulaires des résidus cimentés et du béton tassé au rouleau avec des teneurs en ciment et des rapports eau-ciment semblables. Als Teil der Sicherheits- und Stabilitätsstudien an drei Bergwerken in den Vereinigten Staaten von Amerika installierten Forscher Erddruckgeber und Einbindungsdehnungsmesser in zementierter Steinschüttung, um Spannungs- und Dehnungsveränderungen während der fortlaufenden Bergarbeiten und der Belastung der Steinschüttung zu messen. Daten von diesen Instrumenten wurden dazu verwendet, das In-Situ-Modul der Steinschüt-ung für zwei Gruben zu berechnen. Ein dreidimensionales numerisches Modell einer zementierten Steinschüttungsschwelle wurde mit den Daten von den im Grubendach und in der Schwelle verankerten Extensometern validiert; dieses Modell wurde dann dazu eingesetzt, um das Deformationsmodul in der dritten Grube zu schätzen, da die Erddruckgeber und Einbindungsdehnungsmesser nur geringfügige Messabweichungen feststellten. Das in diesen Gruben verwendete Steinschüttungsbindemittel variierte zwischen vier und acht Prozent an Trockenkomponenten nach Gewicht, der Wasser-Zementfaktor betrug zwischen 0,42 und 1,0 und die größte Zuschlagstoff-größe in den drei Mischungen schwankte zwischen fünf und zwölf Zentimetern. Die Reichweite der berechneten Werte des In-Situ-Deformationsmoduls fiel etwas breit aus, aber es fand erwartungsgemäß eine Klammerung der Modulwerte zwischen den Zemen-trückständen und dem durch Walzen verdichteten Beton mit ähnlichem Zementanteil und Wasser-Zementfaktor statt.

Jan 1, 2003

By Mr P. W. J. van Rensburg

SOUTH AFRICAN NATIONAL COMMITTEE ON TUNNELLING In 1970, the South African Institution of Civil Engineers, the South African Institute of Mining and Metallurgy, the South African Institute of Mechanical Engineers, and the Geological Society of South Africa held an international conference on tunnelling, known as Tuncon 1970. SUID-AFRIKAANSE NASIONALE TONNELBOUKOMITEE In 1970 het die Suid-Afrikaanse Instituut van Siviele Ingenieurs, die Suid-Afrikaanse Instituut vir Mynbou en Metallurgie, die Suid-Afrikaanse Instituut van Meganiese Ingenieurs en Die Geologiese Vereniging van Suid-Afrika 'n internasionale konferensie in verband met tonnelbou gehou, wat bekend gestaan het as Tonkon 1970.

Jan 5, 1974

By H. W. J. P. Neomagus, R. K. K. Mbaya, J. R. Bunt, N. T. Leokaoke, N. W. Makgobelele

Silicon Smelters consumes more than 80000 t/a of wood-derived charcoal as carbonaceous reductant in the production of silicon metal. More than 10% of this material is discarded as fines (<6 mm) generated due to abrasion during processing. Charcoal fine residues (<650 μm) and polyvinyl alcohol (PVA) binder were used in this study to produce mechanically strong charcoal briquettes for metallurgical application as carbonaceous reductant. The PVA binder was added in mass percentages of 1, 3, and 5 wt% to the charcoal fines. The compressive strength, abrasion resistance index (ARI), drop shatter resistance (SRI), and water resistance index (WRI) were measured as functions of curing for up to 7 days under atmospheric conditions, and the results compared with metallurgical grade coarse charcoal. The ash content of the produced briquettes was found to be high (6.6–8.0%) compared with the coarse charcoal (1–3%). The 3 and 5 wt% PVA-bound briquettes were found to be the strongest, with compressive strengths of 40 and 115 kg/cm2 respectively, with WRI values of 75 and 73% respectively. The produced briquettes were found to have lower ARI and SRI values compared to the coarse charcoal. Future work should include beneficiation of the fine charcoal discards prior to briquetting, and an increase in binder addition to above 6 wt% to improve the ARI and SRIn.

May 1, 2021

By Siyabonga Malevu

Chemical Initiatives? Umbogintwini plant is the production facility of Chemical Initiatives? business. Umbogintwini?s J Plant manufactures sulphuric acid. The plant was designed and built by Simon Carves, and was commissioned in 1974. The plant was designed to produce 500 tons/day of Sulphuric acid (H2SO4) at maximum rates. The Sulphuric acid manufacturing is through the famous contact process whereby liquid Sulphur is injected through dried air in a burner operating at 1000 °C to form sulphur dioxide (10.5% SO2). The SO2 gas is then cooled in waste heat boiler no. 1 before being fed to a four pass converter which provides 99.5% SO2 conversion to sulphur trioxide (SO3). The SO3 gas is the absorbed by 98.5% H2SO4 through the inter-pass & final tower to make more concentrated acid and dilute it with water back to 98.5% H2SO4 in acid pump tanks and dispatched to storage tanks. The manufactured Sulphuric acid is supplied to a variety of industrial manufacturing customers includes Pulp & Paper industry, Mining industry, Chemical manufacturing industry etc.

Jan 1, 2009

By Siyabonga Malevu

Chemical Initiatives? Umbogintwini plant is the production facility of Chemical Initiatives? business. Umbogintwini?s J Plant manufactures sulphuric acid. The plant was designed and built by Simon Carves, and was commissioned in 1974. The plant was designed to produce 500 tons/day of Sulphuric acid (H2SO4) at maximum rates. The Sulphuric acid manufacturing is through the famous contact process whereby liquid Sulphur is injected through dried air in a burner operating at 1000 °C to form sulphur dioxide (10.5% SO2). The SO2 gas is then cooled in waste heat boiler no.1 before being fed to a four pass converter which provides 99.5% SO2 conversion to sulphur trioxide (SO3). The SO3 gas is the absorbed by 98.5% H2SO4 through the inter-pass & final tower to make more concentrated acid and dilute it with water back to 98.5% H2SO4 in acid pump tanks and dispatched to storage tanks. The manufactured Sulphuric acid is supplied to a variety of industrial manufacturing customers includes Pulp & Paper industry, Mining industry, Chemical manufacturing industry etc. During the 1st quarter of the year 2007, Chemical Initiatives undertook a study to up rate the sulphuric acid plant output by 10% (i.e. from 500 tpd to 550 tpd).

Jan 1, 2009

By Y. F. Bulgakov, Y. V. Melnikova, V. S. Zakharov

A new technology of atmosphere in inertization of fire section with the help of gazeous nitrogen is presented in the report. This technology is based on membrane air subdivision into two streams, concentrated with nitrogen (up to 99%) and with oxygen correspondently with subsequent giving them into the place of fire. This technology belongs to environmentally friendly ones and it has a great number of technical, mobile and economic advantages comparing with the rest of well-known methods of fire extinguishing. This technology application in Ukrainian coal mines allowed to reduce the member of isolated places of fire at the expense of their extinguishing efficiency.

Jan 1, 2003

By Frank Johnson

Between 2000 and 2006, platinum production from the South African mines expanded from 206 to 307 tonnes (DME, 2007). Most of this additional metal has come from traditional ?narrow? reef stoping, generally taken to mean stoping in working places with a mining height of less than 1,5 metres. It is well known that narrow-reef stoping presents safety, technological and ergonometric challenges (Pickering, 2007). In planning for the expansion, which is still continuing, the platinum mining industry realized that it could not simply continue with traditional methods of narrow-reef mining. Particular issues identified were: ? High labour-intensivity: caused by use of hand-held rock drilling machines, labour-intensive support installation and stope cleaning; ? Dependence on rock-drillers: this occupation is no longer an attractive one and there is a reducing flow of new recruits; ? Safety: most of the work is performed close to the new faces, where there is the greatest exposure to the hazards of falling rock.

Jan 1, 2008

By S. Mohanta, I. D. Behera, B. Sahoo

"Run-of-mine coal contains particles of different sizes with different specific gravities, and when this coal is crushed, the amount of material present in a particular density class changes. This alters the washability characteristics of the coal, which affects the quantity, quality, and separation efficiency of the gravity-based coal washing process. The degree of difficulty in washing a typical coal at a particular specific gravity depends mostly on the amount of material occurring within ±0.1 specific gravity range, which is known as ‘near-gravity material’ at that particular specific gravity of separation. In this paper, two numerical indices, namely ‘near-gravity material index’ and ‘index of washability’, are used to quantify the distribution of near-gravity material in different density classes and to evaluate the degree of difficulty involved in the washing process. The results of this preliminary investigation indicate the uniform distribution of near-gravity material in all density classes for finer size fractions, whereas for coarser size fractions more near-gravity material is present in the lower density classes, making the washing process more difficult at a lower specific gravity of separation. IntroductionThe prime objective of coal beneficiation is to remove physical impurities as effectively and economically as possible. The beneficiation process includes various operations on the asmined coal to make it more suitable for enduse application without destroying the physical identity of the coal. There are several coal beneficiation processes, but gravity-based separators remain the most efficient unit operation for removing the undesirable gangue material from run-of-mine coal. These separators exploit the difference in density between coal particles and gangue particles to effect a separation. The feed is introduced into an aqueous suspension of ultrafine magnetite with a particular density. The feed particles with a relative density less than that of the suspension (clean coal) float to the top surface of the suspension, whereas particles denser than the suspension density (gangue material) sink to the bottom. When the difference in density between the particle and the aqueous suspension is large, the separation is easy, but when this difference is less the separation becomes much more difficult since the settling velocity of the particles is very low. This lower settling velocity increases the probability that particles that should report to floats report to sinks, and vice versa, hence increasing the amount of misplaced material. Therefore, the degree of difficulty in beneficiating a typical coal at a particular specific gravity depends on the amount of material occurring within ±0.1 specific gravity range. This is known as ‘neargravity’ material, also termed ‘near-dense’ material, at that particular specific gravity of separation."

Jan 1, 2016

Foamed cement packs offer a viable alternative to conventional timber or other forms of packs for permanent underground support. These packs comprise steel mesh and hoop containment with an outer bag for the grout; woven, laminated polypropylene fabric being ideal for the purpose. The grout is supplied in 25kg bags and fed into a purpose ? designed foam placer machine which delivers the foamed grout directly to the packs from 60 metre long delivery hose. Foamed cement grout as a fill material offers attractive properties for support packs, in summary these are: Variable Grout Strength Grout strength is controlled by the grout density being delivered from the placer machine. This can be changed by the machine settings. Strength Development Fast rate of strength development is possible so that support is available quickly. Pack yield The foamed grouts are compressible so that yielding of the grout pack can be achieved without loss of support. Rate of Filling Three sizes of placer machine are available, these use one, two, or three 25kg bags per minute of grout, pack filling time is therefore a matter of minutes, a typical 0.75m diameter pack x 1.2m high taking some 17 minutes to fill. Tests in a 1000 tonne press have confirmed that the above characteristics can be achieved with foamed cement packs at acceptable cost. This will be illustrated in the paper with experience to date.

Jan 1, 2008

By W. V. Mutler

Present day capital costs are analyzed for a 2,000 metric tonne per day (MTPD) pyrite burning plant and compared with a sulphur burning plant of the same capacity. Power, raw material and steam production rates are then compared for the two facility types. A sensitivity analysis is conducted to highlight the impact changing sulphur, pyrite, capital and operating costs have on the relative economics of these feeds. Technological improvement effects on capital cost and energy recovery are also discussed. Besides the steam produced from the burning of pure sulphur or pyrite, plants using an advanced form of heat recovery can produce up to 10 bar steam using heat from acid formation. The quantity depends on the overall water balance which is influenced by such factors as gas strength and product acid concentration. Modern materials and innovative process design also improve the ability to increase the high pressure steam from the roaster boiler in pyrite plants above the traditional 1.25 kg of superheated steam per kg of acid produced.

Jan 1, 2009

The annual general meeting of the Branch was held at the St. Helena Club on Thursday, August 21, 1969. Mr J. G. Kirchner (Chairman) was in the Chair. Also present were Mr R. C. J. Goode, President of the S.A. Institute of Mining and Metallurgy; Nine Members: Messrs N. A. Honnet, W. R. Lawrie, J. N. Saunders, D. D. Waterman (Committee Members), M. G. Cullen, G. C. P. Labuschagne, H. A. G. Slater, I. G. Thomas, T. Zadkin and Nine Associate Members: Messrs R. Campbell, D. E. Couperthwaite, T. M. Espach, J. M. Ferguson, G. W. Futcher, A. G. C. Merson, E. R. Penny, R. B. Sutherland, J. W. van den Munckhof and One Visitor: Mr D. J. McLaren. The Chairman declared the meeting open and, on behalf of the Branch, thanked the President for coming from Johannesburg to attend. MINUTES OF THE PREVIOUSGENERALMEETING As the Minutes of the General Meeting held on June 18, 1969 had not yet been published in the Journal, the Chairman moved that their adoption and the discussion thereof be deferred to the next General Meeting. This motion was adopted unanimously. CHAIRMAN&apos;S ANNUAL REPORT 1968/69 At Mr Kirchner&apos;s request, Mr. R. C. J. Goode took the Chair during the presentation of the Chairman&apos;s Annual Report. (This report was published in the August 1969 issue of the Journal.) OFFICE BEARERS AND COMMITTEE MEMBERS FOR THE YEAR 1969/70 The Chairman announced that the outgoing Committee had elected the following office bearers for the coming year: Chairman: N. A. Honnet; Vice-Chairman: J. N. Saunders; Immediate Past Chairman: J. G. Kirchner. The Chairman then read a letter from the scrutineers reporting that the following had been elected to the Committee: M. S. Grobler, W. R. Lawrie, L. O. W. Leimer, A. T. Lewis, R. S. Pearson, T. Zadkin. The Chairman thanked the scrutineers for their services, and congratulated Messrs Lawrie, Leimer and Zadkin on their re-election and Messrs Grobler, Lewis and Pearson on their election to the Committee. The Chairman announced that he had heard, with regret, that Mr. T. Zadkin would be leaving the O.F.S. at the end of August, 1969. Mr Zadkin had served on the Committee continuously since the inception of the O.F.S. Branch and records showed that he had only failed to attend three General Meetings in over nine years. The Chairman expressed the gratitude of the Branch for Mr Zadkin&apos;s invaluable services to the Institute, congratulated him on his well earned promotion and wished him well in his new position. INDUCTION OF CHAIRMAN The Chairman introduced Mr N. A. Honnet to the meeting by briefly outlining his past career and, after congratulating him on his election, called upon him to take the Chair. In congratulating the out-going Chairman on a very successful term of office, Mr Honnet said that due to the absence of many Committee Members for a large portion of the year Mr Kirchner had carried a heavy burden, and he moved a vote of thanks and appreciation for Mr Kirchner&apos;s efforts. This was carried unanimously. GENERAL BUSINESS There were no points raised under this heading. MINING AND METALLURGICAL CONGRESS The Chairman called on Mr W. R. Lawrie to give his talk on aspects of the Mining and Metallurgical Congress recently held in Britain. This presentation was illustrated with photographic slides and proved of great interest to Members. Mr D. D. Waterman proposed a vote of thanks to Mr Lawrie and the Chairman then asked Mr R. C. J. Goode to contribute to Mr Lawrie&apos;s address. Mr Goode thanked Mr Kirchner for his efforts during his very successful term of office and congratulated the in-coming Chairman and Vice-Chairman on their election. He then gave a brief talk on aspects of the Congress not dealt with in Mr Lawrie&apos;s address. These included the industry&apos;s requirements of graduates, the necessity of their rapid advancement and the desirability of sending such young men to attend future Congresses. Mr Goode announced that two symposiums will be sponsored by the Institute next year, one on Tunnelling and the other on Open Cast Workings.

By Raphael Banda

1 Initiating Systems ? a definition An initiation system is a combination of explosive devices and component accessories specifically designed to convey a signal and initiate an explosive charge from a safe distance. In the use of explosives, the initiating system performs the functions of transmission and control of the firing signal to each explosive charge. As functional groups, initiating systems may be considered as: Starters Those which provide the initial signal to start the blasting process. Surface systems Products which provide transmission of the starter signal and delay timing (if any) across the surface of the blast outside the blast hole. In-hole systems Products which provide the signal transmission, delay timing (if any) and the initial explosives energy in the blast hole.1 2 Different types of Initiating Systems The initiation systems commonly used in Sub Saharan Africa are: ? Detonating cord and detonating relay systems ? Capped fuse and igniter cord systems ? Shock tube non electric systems ? Electric systems ? Electronic detonators 3 Overview of Electronic Delay Detonator Technology Conventional detonators use pyrotechnic delay elements and the variation of the actual delay periods is at best approximately 1% the nominal delay. The lack of guaranteed precision common to all pyrotechnic systems enhances the likelihood of negative environmental blasting effects.3 For example, take a 500 ms in hole delay. In conventional detonators this means that 95 % of shots fire within 10 ms of the mean. i.e. a window of 20 ms. Taking a fixed interval between shots of 25 ms, with a range of ± 3 ms, a very ragged firing pattern could be expected which in practice would result in non uniform fragmentation.

Jan 1, 2005

By W. V. Mutler

Present day capital costs are analyzed for a 2,000 metric tonne per day (MTPD) pyrite burning plant and compared with a sulphur burning plant of the same capacity. Power, raw material and steam production rates are then compared for the two facility types. A sensitivity analysis is conducted to highlight the impact changing sulphur, pyrite, capital and operating costs have on the relative economics of these feeds. Technological improvement effects on capital cost and energy recovery are also discussed. Besides the steam produced from the burning of pure sulphur or pyrite, plants using an advanced form of heat recovery can produce up to 10 bar steam using heat from acid formation. The quantity depends on the overall water balance which is influenced by such factors as gas strength and product acid concentration. Modern materials and innovative process design also improve the ability to increase the high pressure steam from the roaster boiler in pyrite plants above the traditional 1.25 kg of superheated steam per kg of acid produced.

Jan 1, 2009

By C. G. Anderson

Throughout the world, there are many orebodies or materials which have significant value but also contain arsenic, antimony, and mercury. As regulations on the transport, exposure, disposition and emission of these elements have become more stringent; it has become increasingly more difficult to derive the values from the resources. This paper outlines the fundamentals of alkaline sulfide hydrometallurgy and its successful application to arsenic, antimony and mercury bearing ores, concentrates, by-products, and other materials.

Jan 1, 2008

By H. Griesel

The overall supply of platinum is forecast to rise more than the demand, and market deficit will narrow somewhat, but is still substantial at about 480 000 ounces. Because of this deficit, the price of platinum is expected to remain high, not taking into account the impetus from funds and speculators. With this strong demand for platinum and the high price, platinum producers still need to initiate projects to not only sustain current production, but also expand output into the high demand. However, the rise in the platinum price does not entirely offset the drop in revenue due to the strong rand. Consequently, in the current economic environment, executives and managers are under extreme pressure to initiate only the highest yielding projects and implementing them successfully. During the initiation phase of a project, the cost of changing concepts is the least, and strategic project decisions are the most important. It is during this phase that the most value can be added to a project, therefore requiring inputs from highly skilled, creative and experienced people. This paper will discuss thought processes and paradigms during the initiation of projects that will assist project owners in the selection and initiation of successful and profitable projects. The project initiation process will also be discussed outlining selection models, risk analyses and funding considerations.

Jan 1, 2004

By L. Robles-Stefoni

"Multiple-point simulation (MPS) methods have been developed over the last decade as a means of reproducing complex geological patterns while generating stochastic simulations. Some geological spatial configurations are complex, such as the spatial geometries and patterns of diamondbearing kimberlite pipes and their internal facies controlling diamond quality and distribution.Two MPS methods were tested for modelling the geology of a diamond pipe located at the Ekati mine, NT, Canada. These are the single normal equation simulation algorithm SNESIM, which captures different patterns from a training image (TI), and the filter simulation algorithm FILTERSIM, which classifies the patterns founded on the TI. Both methods were tested in the stochastic simulation of a four-category geology model: crater, diatreme, xenoliths, and host rock. Soft information about the location of host rock was also used. The validation of the simulation results shows a reasonable reproduction of the geometry and data proportions for all geological units considered; the validation of spatial statistics, however, shows that although simulated realizations from both methods reasonably reproduce the fourth-order spatial statistics of the TI, they do not reproduce well the same spatial statistics of the available data (when this differs from the TI). An interesting observation is that SNESIM better imitated the shape of the pipe, while FILTERSIM yielded a better reproduction of the xenolith bodies. IntroductionThe simulation of geological units poses several technical problems that challenge the capabilities of available geostatistical simulation approaches and their ability to deal with spatial complexity of categorical variables. The spatial geometry of diamondbearing pipes and their internal facies controlling diamond distributions are a specific and well-known difficult modelling problem. The geometry of a kimberlite pipe is typically like an inverted cone (Figure 1); the wider part is known as the crater and is located near the surface, and the narrower, deeper part is known as the diatreme. Xenolith bodies can also be found inside the pipe. A very important contribution to the geological modelling of the contours of the pipe is the measure of uncertainty about the location of the contact between the kimberlite pipe and the host rock."

Jan 1, 2016

By H. Wagner

During the last few years a large number of pillars in different mines were investigated. Pillar conditions were evaluated using subjective, empirical, geophysical and numerical methods. A critical comparison of the different methods showed some interesting coherence. This paper concentrates on experiences using the p-wave velocities as an indicator of pillar conditions. Während den letzten Jahren wurde eine große Anzahl von Bergfesten in verschiedenen Bergwerken auf ihren Zustand hin untersucht. Hierzu wurden subjektive, empirische, geophysikalische sowie numerische Methoden angewandt. Dieser Vortrag beschäftigt sich mit den Erfahrungen beim Einsatz der p-Wellengeschwindigkeit zur Beschreibung des Festenzustandes. Le condition géotechnique d’une grand nombre des piliers des mines souterraines différentes sont examinées ces dernières années. On a appliqué des méthodes subjectives, empiriques, géophysiques et numériques. Ce rapport occupe aux expériences avec l’application de la vélocité des ondes de compression pour tracer le condition des piliers.

Jan 1, 2003

By Sylvie Poirier

Researchers at Natural Resources Canada (NRCan) CANMET Mining and Mineral Sciences Laboratories (CANMET-MMSL) and Mining Technologies International (MTI) have designed and built a hybrid diesel-electric mining loader that is the first of its kind to be developed for underground mines. Diesel equipment is popular because of its mobility and most mining operations are reluctant to replace it with tethered electrical equipment despite the obvious elimination of diesel contaminants and significantly lower heat generation (? 35% of an equivalent diesel). However, a diesel-electric vehicle, being currently evaluated by CANMET-MMSL, could be beneficial. In this unit, a constant load diesel generator feeds batteries which, in turn, powers electrical motors that drive the equipment. In a hybrid diesel-electric unit, the constant load diesel generator can be optimized for minimal emissions and hence lower dilution air requirements. This paper will present the project status and the anticipated benefits for mining operations through the application of this technology.

Jan 1, 2008

Bateman Engineering managed the establishment of a second diamond treatment plant at the Letseng Mine in the Mokhotlong District of northern Lesotho, about 100 km from the town of Buthe Buthe. Letseng Diamonds Proprietary Limited, is owned 70 % by Gem Diamonds and 30 % by the Government of the Kingdom of Lesotho. The second plant, which commenced construction in late 2006, doubled Letseng Mines&apos; hard rock processing capacity from 2.6 million t/yr to 5.2 million t/yr, making it the worlds&apos; seventh largest diamond mine by throughput. Bateman Engineering provided the engineering design, procurement and construction management of the new plant.

Jan 1, 2010

1. OPLEIDING IN INGENIEURSWERK VIR IN G ENIEURS- IN -OPLEID IN G 1.1 llegistrasie as Ingenieur-in-opleiding &apos;n Gegradueerde ingenieur wat in &apos;n eksamen geslaag het wat die Raad erkenl, is registreerpaar as &apos;n ingenieur-in-opleiding kragtens die Wet op Professionele Ingenieurs2. Aansoekvorms kan van die Registrateur verkry word. Mineral processing congress The XIIIth International Mineral Processing Congress is to be held in Warsaw from 4th to 9th June, 1979. Seeing that by products and co-products are becoming of increasing importance in mineral processing operations, the theme of the Congress is to be the &apos;Treatment of Raw Materials with Total Utilization of All Constituents&apos;.

Jan 1, 1979