Search Documents

By Dingwu Feng, Jannie S. J. van Devente

"The effect of ultrasonication on reactions at solid/liquid interfaces was investigated in two slurry systems, i.e. gold cyanidation and geopolymerisation. The kinetics of gold extraction were significantly enhanced and the cyanide consumption was reduced in the cyanidation of a pyrite concentrate using ultrasonication, probably due to the prevention of leaching passivation, the improvement of the dissolution of the gold host sulphides and the oxidation of soluble sulphides to sulphate. The effectiveness for ultrasonication was improved with the injection of oxygen and the addition of dithiophosphate through enhancing the formation of the oxidation radicals and selectively inducing cavitation bubbles directly at the sulphide interfaces. Ultrasonically enhanced cyanidation could render currently uneconomic deposits viable for extraction by improved cavitation efficiency with the aid of surfactants.Ultrasonication increased the compressive strength of the formed geopolymers through accelerating the dissolution of the Al-Si materials, strengthening the bonds at the solid particle/gel phase interfaces, enhancing the polycondensation process and improving the formation of semi-crystalline to crystalline phases. The use of power ultrasound will yield high-performance geopolymer materials."

Jan 1, 2003

By Darryel Boucher, Raymond Langlois, Neil Rowson, Kristian Waters

The Knelson Concentrator is a centrifugal gravity concentrator composed of a high speed rotating bowl into which a mineral slurry is fed. The rotational motion creates a centrifugal acceleration up to an equivalent of 200 G. Under this acceleration, particles enter fluidised riffles along the side of the bowl, with the fluidisation allowing for the substitution of dense material for less dense. The separation mechanism is not fully understood and questions remain on the optimal residence time, slurry feed parameters and bowl surface profile to achieve a better separation. The positron emission particle tracking (PEPT) technique has been applied to record the motion of a -1700+1180 µm particle of a quartz-gold matrix, labelled with 18F radioisotope while it undergoes concentration inside a 3" laboratory scale Knelson Concentrator (KC-MD3) operated at 60 G. The slurry used was composed of quartz and magnetite. Particle trajectories during the first stage of the concentration process where the heavier particles centrifuge through the increasingly dense slurry towards the riffles of the bowl are shown with respect to time. This work reveals new information on particle motion inside the Knelson Concentrator and the results will be used for validation of developed separation model as well as optimisation of a centrifugal concentrator’s performance.

Jan 1, 2014

By E. V. Bratygin, E. G. Dmitrieva

The aim of the research was to study the thermodynamic characteristics of high-temperature processing of ilmenite concentrate deposits "Central" in a neutral and oxidizing atmosphere, as well as its interaction with alkaline additives. The research was conducted using a scanning colonoscopy on thermogravimetrical analyzer NETZSCH STA 449 F3. A sample of the test material weighing 10 mg was placed in a crucible and heated at a rate of 10 °C/min to 1200 °C in argon or air. Studies have been conducted pure ilmenite concentrate and its mixtures with 5 % and 12.5% of sodium carbonate. The results of the analysis of the thermogravimetric curves it was found that the recovery of the concentrate carbon will come from ulvospinel, not pseudobrookite, and the reaction recovery is possible at temperatures above 900°C. While removing produced in the decay ilmenorutile of iron oxides in an inactive form, for example, iron (III) oxide, it is possible to reduce the quantity of the solution of ilmenite formed during the restoration of the melt anosovite. The analysis of data obtained during heating of ilmenite concentrate with sodium carbonate in concentrations of 5 and 12.5% transition pseudobrookite in ulvospinel is missing, it just breaks down into hematite and titanium oxide, which, in turn, react with N?2??3. It should be noted that increasing the concentration of sodium carbonate in the sample contributes to more complete interaction of iron oxides and N?2??3 with formation of ferrites of sodium. This can ensure full recovery of iron oxides in the concentrate, which is part of secondary ilmenite can not be dissolved in the melt formed by the lower oxides of titanium. In addition, the increase in the content of soda in the mixture significantly reduces the temperature of the initial melting point of the slag and facilitates the coagulation of metallic iron.The obtained results were used for laboratory studies of the solid-phase sintering of briquettes from ilmenite concentrate with additives of sodium carbonate and a reducing – coal, as well as for the development of technological mode of solid-phase sintering of the concentrate with the aim of obtaining product recovery with a titanium dioxide content of more than 75 %.

Jan 1, 2018

By Peter Scales, Ricardo Jeldres, Fernando Concha, Pedro Toledo, Shane Usher, Anthony Stickland

The impact of several electrolytes present in seawater on the rheological properties of flocculated mineral suspensions was assessed using the creep test. Flocculated suspensions were obtained by adding polymer flocculant to a cylinder of mineral suspension and aggregating the suspension using the plunger method. The suspension was allowed to sediment and the supernatant liquid decanted prior to tests for the viscoelastic properties of the resulting sediment. The solid used was alumina AKP-30 both, below and above the isoelectric point. The polymer used was AN934SH, an anionic flocculant with high molecular weight. Salts analyzed were MgCl2, CaCl2 and NaCl, known as water structure makers, and KI and KCl, known as water structure breakers. A high salt concentration of 0.5 M was used to approach the ionic strength of seawater. For both pH’s studied, the sediments demonstrated a viscoelastic non-linear behavior observed as a non-linear relationship between yield strain and applied stress. In the absence of flocculant, it was observed that the viscosity and yield stress of a suspension increase in the presence of structure maker salts for the case of both silica suspensions and alumina suspensions. These results were explained using hypernetted chain statistical mechanics models describing the interaction of ions with solvated surfaces. In contrast, with the presence of flocculant, the shear yield strain of alumina suspensions increases with the breaker character of the salts, however, this result has been explained by an extension of the results from the models. The work has significant implications for the flocculation of mineral suspensions in the presence of seawater.

Jan 1, 2014

By V. P. Yakushkin, B. S. Ksenofontov

"Multistage model designed and used for more detailed description of floatation process. The study develops a new model of flotation kinetics description. It defines flotation as process that consists of several stages: air bubbles and particles are separate, air bubbles and particles form a raising aggregate, aggregate raises to froth layer. This description significantly differs from commonly used model, which is much simplified. The multistage model gives an in-depth description and considers different aspects of flotation. Experimental approval of the new model resulted in its accuracy.The model is to be used for description of all flotation processes’ kinetics of wastewater treatment. It helps in accurate designing of flotation treatment plants and may be used for further research of flotation process. Columnar flotation installation was designed by using multistage model. This installation consists of new tubular aerators with special ejectors, froth pressing system as well as unit of thin-layering lighting to catch microflotocomplex “particle – bubble”. Usage of tubular aerators allowed to aerate the overall volume of pulp. Due to use of special ejectors with longer mixing camera we state higher volume of small-sized floto-active bubbles. Use of multistage model allowed to optimize and get higher technological results of potash salts enrichment. Tests were conducted on centrifuges-floatation installation system. Meanwhile, froth concentrate contained mainly thin hydrophobic particles sized circa 0,1 mm. As a result we set that during floatation cleaning process of froth concentrate 95-98% of chloride potassium (KCI) is derived from foam.The final product satisfies production quality. Columnar floatation installation productivity was 17 – 21 m3/m2h, which is a high technological result. Columnar floatation installation is one of the best examples of concentrating equipment using nearly all technological indices."

Jan 1, 2018

By Kremena Dedelyanova, Tsvetan Damyanov, Nikolay Hristov, Evgeni Kostadinov, Lubomir Kuzev

"Spherical grinding media (balls) are the most widely used media for comminution of ores by grinding. One way to optimize the grinding process in a tumbling mill is associated with the development and testing of a new media shape. By modelling simulation study of the behaviour of two types of grinding media (balls and tetraballpebs) in the grinding process was conducted to determine the possible advantages of the new media shape. Tetraballpebs are in the shape of tetrahedrons with spherical convex walls. D305 mm and L305 mm Bond ball mill sizes were used in the experiment. They are modelled milling tetraballpebs bodies corresponding by weight to five ball sizes, namely ¾, 7/8, 1, 1¼ and 1½ inches which form the grinding media used in a Bond ball mill. They are cast steel grinding bodies. Studies carried out with both types of grinding media include equal number of milling bodies of the same weight and volume. Having thus ensured a uniform mass of the grinding media and the same number of milling bodies, all other conditions and process parameters being identical, conclusions can be drawn about the influence of the grinding media shape on the grinding process. Compared to steel balls, the tetraballpebs used in laboratory tests carried out in closed cycle by Bond ball mill and the study of the rate of grinding gave five to six per cent higher yield of a control size of minus 0.1 mm. Measurements of the Bond ball mill power consumption demonstrated that tetraballpebs grinding media achieved energy saving of 4.7 per cent for the production of one gram of the control size of minus 0.1 mm."

Jan 1, 2014

By Brian Lindner, Lidia Auret, Niel Knoblauch

In this paper, a fault detection and identification framework based on feature extraction and topology extraction methods is proposed, and evaluated on a simulated base metals refinery high pressure leaching process. Feature extraction methods included linear and kernel principal component analysis, while process topology information was extracted with linear cross-correlation, partial cross-correlation and transfer entropy. Connectivity maps were constructed to identify possible fault propagation paths to aid root cause analysis. The results indicate that process topology can enhance the fault identification capability of data-based process monitoring methods. The study of the considered base metals refinery pressure leaching process is ongoing, with future work including the creation of a fault library which would lead to further critical evaluation of the proposed fault detection and identification framework.

Jan 1, 2014

By V. V. Morozov, I. S. Barmin, A. V. Tugolukov, V. V. Polivanskaya

"It was presents the results of research on improving reagent regime and scheme of enrichment of slime classes of Apatite-Staffelite ores and tailings stockpile of Kovdorsky enrichment plant. It was investigated the regularities of flocculation in the processes of thickening and selective flotation apatite-bearing ores. It was established character of the influence of flotation reagents on the flocculation process. It was shown that the sodium silicate and soda ash have a stabilizing effect by thickening of sludges. Neonol and oleic acid have a coagulating or flocculating effect. It was tested the new regime flotation, involving an initial conditioning with using of reagent - dispersants before feeding the pulp into the flotation and subsequent conditioning with reagents having a coagulating effect. The flowsheet and reagent regime for enrichment of fine-grained tailings stockpiled was developed, which providing production of standard apatite concentrate and increasing the recovery of valuable components. There are presented results of the research of activities of strong organic surfactant on solubility of colloidal form fatty acid collector and aggregate stability of fine minerals in the process of thickening and flotation. Surfactants such as Neonol have been investigated for increasing the activity of the collectors. When using the process of thickening sludge fraction with flocculant Praestol 2540 and stadial conditioning of sludge were obtained concentrates containing up to 38.1% P2O5 at recovery. INTRODUCTION A feature of the Apatite-Staffelite ores of the Kovdorsky deposit is the presence of a large number of fine mineral particles and a reduced hardness of phosphate minerals (Beloborodov et al., 2010, Tugolukov et al., 2012). Formed in the ore-preparation process, sludges are lost with a discharge in the thickening operation. Sludge is characterized by an increased content of phosphorus pentoxide (P2O5). Losses of P2O5 at enrichment of the stale tailings of Kovdorsky GOK reach 14.0%. The high losses of P2O5 caused a profound study of the behavior of thin apatite classes under conditions of thickening and flotation."

Jan 1, 2018

By B. McFadzean, P. E. Ngoepe, P. P. Mkhonto, J. Taguta

The adsorption of heterocyclic collectors such 2-mercaptobenzothiazole (MBT), 2-mercaptobenzoxazole (MBO), 2-mercaptobenzimidazole (MBI) and their derivatives on pyrite form a basis in understanding the flotation reactivity that may be applicable in a wide range of sulphide minerals. This study uses a computational and experimental approach to determine the heat of adsorption of MBT, MBO, MBI and modified MBT collectors onto pyrite surfaces. Computational calculations found that the adsorption energies were in the order: MBO > MBI > MBT. The heterocyclic collectors were adsorbed in their thiolate form on the surface. In the case of the pyrite (100) surface, the MBT adsorbed through the exocyclic sulphur atom, while MBO and MBI adsorbed through the exocyclic sulphur and N atoms onto the 5-coordinated Fe atom. The (111) surface was found to be more reactive and different adsorption mechanisms were predicted, where the MBT exocyclic sulphur atom bridged on the 5- coordinated Fe and surface 2-coordinated sulphur atoms, while the N atom adsorbed on the 5-coordinated Fe atom. In the case of MBO and MBI, dissociation of the exocyclic sulphur atom from the collector occurred with subsequent interaction with the surface 5-cordinated Fe and 2-coordinated S atoms. This resulted in the collector carbon atom adsorbing on the surface 2-coordinated S atom, while the N atom adsorbed on the 5-coordinated Fe atom. The adsorption of the modified MBT was found to be more exothermic than the MBT, which showed that introduction of a –CS2 group on the exocyclic sulphur atom improved the affinity of MBT on the surface, and was thus a better flotation collector. The computational results were supported by experimental enthalpy of adsorption measurements and microflotation tests. The chemistry of the heterocyclic thioamides is complicated by the fact that they can exist in a number of tautomeric and ionic forms at different pH’s. This is discussed in relation to the flotation and calorimetric data.

Jan 1, 2018

By Wei Zhang, Jinhong Zhang

"In froth flotation, the adsorption of collector on mineral surface is critical for a successful flotation process. In present work, an atomic force microscopy (AFM) has been applied to study the adsorption of potassium amyl xanthate (PAX) on copper sulfides, i.e., chalcopyrite, chalcocite and bornite. The in-situ collected AFM images show that PAX adsorbs on chalcopyrite mainly in the form of oily dixanthogen; while it strongly adsorbs on chalcocite and bornite in the form of insoluble metal xanthate, which binds strongly with the mineral surface. The information obtained from the AFM study shed lights on the collectivity and therefore the selection of specific collector for different copper sulfide minerals in industrial practice.INTRODUCTIONFroth flotation, which treats the highest throughput in mining industry and produces the maximum economic outcome of any surface chemistry process, has been widely applied for the concentration of copper sulfide minerals, i.e., chalcopyrite, chalcocite and bornite. In flotation, collectors are added into the pulp (mixture of water and fine-grained minerals) to selectively adsorb onto the target mineral and render its surface with high hydrophobicity, which is generally beneficial for a strong mineral-bubble attachment and thus a high flotation recovery. Therefore, the adsorption of collector on mineral surface is vital for a successful flotation process and it has been studied by applying various surface analysis techniques, such as IR (Infrared Spectroscopy), CV (Cyclic Voltammetry) and XPS (X-ray Photoelectron Spectroscopy). (Poling, 1963; Allison et al., 1972; Mielczarski et al., 1984; Leppinen et al., 1989; Kartio et al., 1996) These studies have revealed a lot of information, such as the reaction, product and mechanism, of the adsorption of chemicals on mineral surface. It is also of great interest to directly get the image of adsorbed collectors on mineral surface changing with pulp chemistry, such as pH, redox potential, ionic strength and chemical’s dosage."

Jan 1, 2018

By Richter, E. Charikinya

"Mineral processing unit models require information on particulate properties such as particle size, solids flowrate and mineralogical composition to model their operations. Process models that describe the separation process can be classified based on the level of information required from the ore, i.e. the feed stream to the separating unit. The most comprehensive level of mineral processing models is the particle-based modelling approach. Particle based modelling describes a modelling approach where mineral composition, mineral liberation and textural information of particles making up the process streams is used in modelling. The advantage of this approach is that all model streams carry particle level information (size, liberation, shape). This information is obtained by applying automated mineralogy techniques such as Quantitative Evaluation of Minerals by Scanning Electron Microscopy (QEMSCAN) analysis which provide accurate and detailed information on process stream particle properties. Currently the use of liberation information in modelling and simulation is rare, due to the limited number of separation models that liberation data as input. The objective of this study is to develop a particle based model for a dry magnetic separator, where mineralogical information is used directly to simulate a dry magnetic separator operation. Magnetic separation tests were carried out on high, medium and low grade magnetite ores using a laboratory magnetic separator. Streams from the separator were sampled and sized for chemical and liberation analyses. A sized mass and elemental balance around the magnetic separator was carried out. The elemental assays of each stream were converted to mineral quantities and a sized mineral balance was done. QEMSCAN measured liberation data was reconciled to the mineral balance based on mineral quantities obtained from chemical assays. This was followed by the development of a particle based model that calculates the trajectory of a single particle based on its mineral composition and textural properties. The model was tested on experimental data and was able to predict the effect of variation in process feed stream mineralogical attributes (liberation, grade, particle size) on magnetic separation performance. Results of this study highlight the benefits of the particle based modelling approach. INTRODUCTION The extraction of mineral values from ore requires liberation of the value minerals from the gangue followed by their separation. Liberation is achieved by size reduction operations (Desmond, 2008; Fuerstenau and Abouzeid, 2002). Separation of gangue material from value mineral takes place in various mineral upgrading stages such as classification, magnetic separation and flotation. In these concentration stages value minerals are separated from gangue minerals based on the physical properties of the ore particles making up the feed such as size, liberation, volume of magnetic material and density. The success of separation is related to the liberation of the feed particles, the performance of the separation technology applied, as well as the inherent characteristics of the feed material (Leißner et al., 2013)."

Jan 1, 2018

By F. Karakas

Water based paint formulations consist of some industrial minerals with quantities varying from 20 to 50 %. Quality of paint is directly related to these minerals used as pigment or filler in the production. Titanium dioxide is the most important and expensive pigment in paint formulations. Other minerals such as calcite and calcined kaolin are used as filler and mainly as a substitute for TiO2. Consequently, particle-particle interactions including adsorption, coating and size distribution of pigment mixture directly affects the paint quality. In the present paper, a new type of pigment mixture for possible use in architectural water based paints was developed through grinding. The effect of different types of grinding methods on physical properties of TiO2 and calcite mixture and the quality of paint produced by these mixtures have been revealed. Three different types of mills; conventional ball mill, vibratory ball mill and high-speed attritor were used for grinding of TiO2 and calcite. Viscosity, zeta potential and particle size distributions were used to characterize the pigment mixtures obtained upon grinding. The quality of paint was evaluated by standards based on both wet and dry paints such as viscosity, density, opacity and gloss. The paint produced with the pigment mixtures prepared in vibratory ball mill and high speed attritor showed improvement in physical properties particularly in the distribution and dispersion of mineral particles. Keywords: grinding, pigment, paint, TiO2, calcite

Sep 1, 2012

By Felipe Sepulveda, Edelmira Gálvez, Luis Cisternas

"In mineral processing, the recovery and/or concentration of the value components cannot occur in one operational stage, therefore requiring the use of separation circuits based on several flotation stages. The components to be separated are typically distributed at different concentrations and different particle sizes, resulting in different levels of recovery. Typically, more than one value component must be selectively removed by exploiting the differences in the components’ floatability at different pH values, pulp potential and particle size. Several methods for the design of these circuits are available in the literature, but comparatively few studies present circuit analysis tools or address the design of a multiple-product flotation circuit. In this study, global sensitivity analysis was used to analyze a flotation circuit with several products, such as copper, lead and zinc. This analysis was based on the Eureka mine concentrator plant. The analysis was performed for each of the sections of the circuit as an overall evaluation of the circuit. The Sobol’ method and the correlation method were used to evaluate the Eureka mine concentrator plant using the SimLab 2.2 software."

Jan 1, 2014

By Francisca San Martín, Martin Rudolph, Willy Kracht, Tomás Vargas

It has been shown that bacteria Acidithiobacillus ferrooxidans can be used to depress pyrite in seawater flotation at natural pH, which opens the possibility for its use as an alternative to lime to depress pyrite in copper sulfide flotation. In order to have a better understanding of the mechanisms involved in pyrite depression with A. ferrooxidans, an exploratory experimental campaign was carried out, including attachment density and contact angle measurements, and the effect of adding bacteria before or after collector. Biodepression of pyrite improves when increasing pH from 3 to 8, with a decrease in recovery from 92% to 36%. This increase in depressing capability is accompanied by an increase in attachment density, from 2.58×108 bacteria/g to 1.99×109 bacteria/g at pH 3 and 8, respectively, suggesting that the mechanism of depression is related to the attachment of bacteria to the pyrite surface. It was observed that the conditioning sequence with collector and bacteria influences the biodepression capacity of A. ferrooxidans. Having as a reference a value of pyrite recovery equal to 97%, when using only xanthate in seawater flotation at pH 8, the effect of both conditioning with bacteria-followed-by-xanthate and xanthate-followed-by-bacteria were assessed. When bacteria were added before the collector, the recovery of pyrite decreased to 36%. On the other hand, when bacteria were added after collector, the recovery was 64%, showing that biodepression of pyrite with Acidithiobacillus ferrooxidans is more efficient when the conditioning is carried out first with bacteria. The contact angle values show that there is little effect of the second component added to the system, i.e., if pyrite is first conditioned with bacteria, the contact angle does not change significantly once the xanthate is added (bacteria-followed-by-xanthate). The same was observed when the conditioning sequence was xanthate-followed-by-bacteria.

Jan 1, 2018

By Rolf Lauten, Yongjun Peng, Yufan Mu

"Biopolymers, produced from cellulosic biomass, have promising prospects of application as depressants in mineral processing. In this study, three different types of biopolymers (i.e., DP-1775, DP-1777 and DP-1778) were used to study the effect of polymer structure on flotation of un-activated pyrite, copper activated pyrite and chalcopyrite. It was found that the depressing effect of DP-1775 and DP-1778 was much stronger than that of DP-1777, and pyrite was depressed to a greater content than chalcopyrite with the same biopolymer at the same dosage. The biopolymer concentration played a vital role in determining the degree of depression. For each biopolymer, the higher the concentration, the greater the minerals were depressed. The mechanism underpinning the depressing effect of these biopolymers was explored in this paper. The concentration of biopolymers could determine the properties of the adsorption layer and the confirmation of biopolymer chains on mineral surfaces. The biopolymer molecules may aggregate when polymer concentration was over a critical value. Molecular weight and functional groups of biopolymers were the key factors characterizing the depressing capability of different biopolymers. Differences between the tested biopolymers and features of the adsorbed layer might account for the observed trends in ability to depress pyrite and chalcopyrite flotation. The greater depressing effect of biopolymers on pyrite over chalcopyrite might result from the preferential adsorption of biopolymers on pyrite over chalcopyrite."

Jan 1, 2014

By Bruno Michaux, Markus Reuter, Martin Rudolph

"It is relatively well-established in the literature that the flotation of calcium minerals using fatty acids as collector is very sensitive to the process water composition. In particular, hard waters have often been reported to strongly reduce the target mineral recoveries due to the formation of insoluble compounds such as calcium and / or magnesium dioleate, thus reducing the amount of collector available for adsorption onto the mineral surface. In this study, the flotation of a fluorite pre-concentrate was performed with tall oil, an industrial collector essentially containing fatty acids. The tests were performed in a variety of synthetic waters to simulate multiple degrees of water hardness, and to differentiate the role of magnesium and calcium ions on the flotation performance. The flotation tests revealed that, under the studied conditions, a significant difference between flotation in calcium-rich and magnesium-rich waters was observed, suggesting strong ion-specific effects in the system. Specifically, calcium-rich waters slightly improved the fluorite recovery, whereas magnesium-rich waters caused a decrease in recovery by as much as 20%. This paper is focused on the flotation kinetics aspect of the system. This approach highlighted the interesting finding that calcium ions did not simply increase the fluorite recovery, but also significantly increased its flotation kinetics. The magnesium ions, on the other hand, had the exact opposite effect.INTRODUCTIONAs the mining industry is facing an increasing number of issues related to its fresh water consumption, the idea of using alternative water sources for mineral beneficiation is gaining significant momentum. As a result, a proper understanding of the role of water chemistry in flotation is becoming more and more urgent, leading to an increasing number of studies on this topic."

Jan 1, 2018

By I. Silin, H. Wotruba, J. Huben, A. Ognyanova

"With increasing shortage of raw materials, the beneficiation of ultra-fine ores will play a larger role in the near future. Many established process technologies do not yield satisfactory separation results for ultra-fine materials. Without selectivity, high-grade concentrates cannot be produced. The material at hand is a taconite which had to be ground to d(90) = 25 µm to guarantee liberation of the iron oxides. The comminution was done by High Pressure Grinding Roll (HPGR) and resulted in smooth surfaces and clear grain boundaries. This is an indication of selective grinding and mineral liberation. Further processing steps included selective desliming, magnetic separation as well as reverse flotation. INTRODUCTION During the last centuries, the processing of iron ores became increasingly important. The coarse-grained, so-called lump ores that are ready for direct usage in blast furnaces without further processing are becoming gradually less abundant. The processing of ultra-fine-grained ores, which in addition require a complex ore beneficiation due to the composition of the material, will progressively gain relevance with increasing resource shortages in the future (Arvidson, 2013). The term “ultra-fine” does not hold a precise definition in mineral processing. In this paper, “ultra-fine-grained” ores are defined by the required grind size for full liberation smaller than 20 µm. Many established mineral processing technologies do not yield satisfactory separation results for ultra-fine materials. Thus, they are limited in their application to produce high-grade concentrates suitable for sintering and pelletizing for direct reduction processes. The production of a high-grade iron concentrate (over 68% Fe) with low silica content (under 2.5% SiO2) is possible from both magnetite and hematite containing ore. In addition to the mineral processing technologies (magnetic and gravity separation, flotation), technologies for the liberation of fine-grained iron ores need to be developed and improved. In contrast to the conventional wet grinding circuit by means of tumbling mills, several future trends in dry and wet grinding and regrinding are already in use. These include technologies such as vibration mills (Palla®Mill), stirred media mills (Vertimill®), vertical roller mills (Loesche) and high-pressure grinding rolls (HPGR) (Jankovic, 2015). This study preliminary investigated the mineral processing of a low-grade, ultra-fine-grained, complex iron ore in a laboratory scale after dry grinding by HPGR to 90% < 25 µm without consideration of the grinding, milling, energy and classification cost."

Jan 1, 2018

The simulation study on the process of iron ore beneficiation plant of Essar Steel, Kirandul was carried out. The iron ore fines and slimes generated nearby Bailadila mines of NMDC are used as raw materials for this beneficiation plant. The capacity of the plant is 1400 TPH operating in parallel in two streams. The capacity of the plant was utilized about 60% of throughput capacity. To improve the plant capacity as well as quality performance, the simulation study was conducted to detect the bottleneck of the process. The process samples were collected from input and output of each processing unit operation to generate the data base for simulation study at the feed rate of 400 and 500 TPH of iron ore fines in a single stream. The characteristics data i.e., breakage and selection functions were generated using MILLSOFT package for simulation of ball mills. Then MODSIM package was used to evaluate the performance of each unit operation to identify the bottleneck. It was established by a simulation study that the intermediate thickener draws high current when the feed rate is more than 400 TPH due to high torque drawn by rotating rake because of presence of coarse particles in the input stream to thickener. The problem was sorted out by classification of input stream of thickener to remove the coarse particles. Then the process was simulated at its rated capacity, and experimental validation studies at the plant were also conducted at the feed capacity of 600 and 700 TPH by modification of process flowsheet. The experimental data was almost matching with simulated data. Finally, the processing plant is running with full rated capacity without any bottleneck. Keywords: simulation of ball mill, breakage function, selection function, iron ore

Sep 1, 2012

By Diego Mesa, Willy Kracht

Frothers may be classified as weak or strong depending on their ability to produce stable froths, which is related to the amount of water that they transfer from the pulp to the froth. They can also have an effect on the non-selective mechanism of recovery by entrainment, implying that both selectivity and froth stability are, at least to some extent, frother dependent. Solids, on the other hand, also have an effect on froth behaviour. Clays, which are characterized by their small particle size, laminar shape, and high specific surface, tend to report to the froth phase and have an enormous impact on both froth stability and the overall performance of the flotation process. The purpose of this work is to shed light on the effect that different frothers have on the froth behaviour when clays are present. In order to do that, two sets of experiments were conducted using frothers from the families of alcohols and polyglycols. For each test, the equilibrium froth height was measured at different frother concentrations in an agitated machine with an acrylic square-base cell that was 11 cm wide and 25 cm high. The cell was designed in such a way that froth was able to grow without concentrate discharge. In the first set of tests, pure clays such as kaolinite and montmorillonite were used. In the second set, an actual copper sulphide ore with a high content of clays was used as solid phase. The results, expressed as curves of equilibrium froth height against frother dosage, showed a coupled effect of frother-clay on froth behaviour for both sets of experiments. In some cases, the froth grew up until the border of the cell with only a few parts per million of frother. In other cases, the equilibrium froth height varied smoothly with frother dosage. The results suggest that choosing the right frother can be of use for controlling the froth behaviour when dealing with clay-rich froths, using frother dosage as the control variable. The application of these findings at industrial scale are discussed and some recommendations are given.

Jan 1, 2018

By Felipe Henríquez, Daniel Silva

"Traditionally, the implementation of an automated advanced process controller in any mineral processing complex is a challenge, mainly due to the quality of resources and technologies required, the uniqueness of each control solution and the uncertainty of the engineering hours needed to complete the task. Thus, the use of advanced and proven control technology becomes a key factor when deploying the control strategy. However, success would still not be possible without the presence of common sense, process knowledge and fundamental process data. Minera Los Pelambres, taking advantage of such factors and its accumulated process experience, implemented a novel and successful combination of MPC (Multivariable Predictive Control) and advanced control for secondary grinding and regrinding stages at its copper concentrator plant. In both cases, the control objectives are: being capable of processing a variable feed from the upstream process while at the same time avoiding to become a process bottle neck and yet, maintaining an adequate product quality (in terms of size distribution) to the process downstream. Additionally, for the case of the vertical regrinding mill (vertimill), the control system should also be capable of keeping an adequate circulation load and making an efficient use of the available grinding power. In either case, extending hidrocyclones availability while maintaining their performance is a must, since both factors are required for process and maintenance purposes. Thus, the process control problem becomes one with a multi-variable type of process with multiple control objectives to satisfy simultaneously. In trying to solve it, many mineral processing operations have implemented basic or conventional control or even better yet, expert systems. Minera Los Pelambres believes that better and faster results can be achieved using a combination of MPC and advanced control. Such strategy was successfully implemented, reducing considerably process variability while maintaining high throughput and keeping the process well within constraints limits. Their control philosophy, implementation process, main results and their key performance indicators are discussed here."

Jan 1, 2014