Search Documents

By A. P. Liu

Semi-industrial test on fine products of Meishan dressing plant was carried out with type RP80/25 high pressure roller mill produced by Homburg Corporation of Germany, and the influences of such factors as energy consumption, water containing, throughput and circulating load on rolling effect were investigated. Closed circuit experiment result showed that Meishan iron ore could be suitable for powder grinding with high pressure roller mill, and energy consumption of the operation was declined by 25%~30%, which was favorable for energy-saving, increasing production efficiency and improving grinding effects. According to above experimental results, this paper put forward the technical proposal of application of high pressure roller mill in Meishan, and pointed out some technical problems which needed to be settled urgently in technology disposal.

Jan 1, 2014

By B. Vasanthakumar, H. Ravishankar, S. Subramanian, J. Braun

The flotation of sphalerite and galena in the presence of intra- and extra-cellular components isolated from Bacillus circulans before and after adaptation to the chosen minerals has been studied. Based on various biochemical treatments, the key biomolecule primarily responsible for the flotation of sphalerite has been identified as DNA, which functions as a bio-collector. A noteworthy finding is the considerably higher flotation recovery of sphalerite obtained in the presence of single stranded DNA (79.8%) vis-à-vis double stranded DNA (50.2%). Selective flotation tests using the soluble fraction obtained after thermolysis treatment highlight that sphalerite-adapted cells yield a higher selectivity index (S. I.) of 31.2 compared to galena-adapted (S.I. 4.3) or unadapted (S.I. 12.2) cells. During bacterial adaptation to the above chosen minerals, the quantitative and qualitative changes in the surface potential, surface morphology and cell wall components have been monitored. The prior adaptation of the bacteria to sphalerite results in the secretion of a higher amount of proteins, eDNA and phosphate, whereas adaptation to galena leads to a higher amount of polysaccharide, uronic acid and acetylated sugar, vis-à-vis the unadapted bacteria. A significant observation is that the bacteria undergo a change in morphology from rod to sphere as a strategy to resist metal toxicity during adaptation to galena. Interestingly, this phenomenon is not observed during bacterial adaptation to sphalerite. This morphological transition has been shown to involve changes in crucial cell wall components as well as changes in the levels of expression of bacterial cytoskeleton element mreB gene involved in the maintenance of the rod shape. The sequence of B.circulans mreB gene has been identified using Polymerase Chain Reaction (PCR) followed by DNA sequencing.

Jan 1, 2014

By Priyanka Dhar, Kurt Aasly, Hanumantha Rao Kota, Hassan Bouzahzah, Maria Thornhill

The interest in investigating the processing characteristics of mineral deposits in Norway has seen an upsurge in the last decade. One of the major areas of interest is a huge copper deposit, operated by NUSSIR ASA located in the Repparfjord Tectonic Window in the caledonides of west Finnmark. This study reports analysis of ore from the deposit for development and modifications in the flotation flowsheet for the NUSSIR ASA copper ore. The mineralogical characterization for the ore sample was achived by optical microscopy and Zeiss automated mineralogy while grinding characteristics were tested using Bond Index tests. The results confirmed the presence of Cu minerals in the form of chalcocite, chalcopyrite and bornite in the samples, which are mainly liberated in the – 105 µm size range. The majority of non-liberated copper sulphides associated with silica and the carbonates varies from 3 to 28 percent in the –250 µm samples . It is also observed that the copper minerals are uniformly distributed in all size ranges. Selective flotation of NUSSIR copper ore was performed in different size fractions with a motive to identify the correct liberation size and thus to obtain a copper concentrate meeting the quality requirements. The flotation experiments are essentially performed in two stages: the rougher and the cleaner stage. Mass balance calculations were performed showing that approximately 88 percent of copper can be obtained at the end of the process. Ultimately, overall circuit copper recoveries ranged between 83.5 to 88.1 % with a concentrate grade of 35 to 48 % Cu.

Jan 1, 2018

By A. Zangooi

Frothers play major roles in flotation through interaction at the air/water interface. A method of determining frother adsorption density (coverage), i.e., the number of molecules per unit of interfacial area of bubble surface, is introduced. The technique is based on mass balancing the frother around a continuously operated bubble column. The mass balance requires collection of bubbles before they burst. The column design and operating procedure is reviewed, and some preliminary results discussed. Keywords: flotation, colorimetric frother analysis technique, frother mass balance, coverage

Sep 1, 2012

By M. J. Lottering

Gold deposits in South Africa are invariably associated with uranium bearing minerals. Although it is low grade uranium by international standards, averaging around 0.3 kg U3O8 per ton of ore, recovery of uranium as a by-product improves the overall economics of gold extraction. Moreover, the current high uranium prices as well as increased demand due to renewed interest in nuclear power provide significant incentives for dedicated uranium production. An understanding of the uranium leaching response to changes in operating conditions is an important first step to-wards optimisation of uranium recoveries. In South African acid leaching plants, uranium dissolutions higher than 90% are difficult to achieve, and the chemical origin of this limit is not clear. To study leaching behaviour, an important consideration is the mineralogical characteristics of the ores. Typically, a diagnostic leaching approach can be followed. In this paper, a mineralogy-leachability explanation is presented to rationalise the difficulty in exceeding 90% dissolution from low grade uranium ores on the basis of a simple diagnostic leaching method. It was found that brannerite was the main reason for the existence of a dissolution limit in Witwatersrand ore and that chemical liberation was more effective to increase end dissolution compared to physical liberation. The findings from these investigations will form guidelines for developing economically viable flow sheets for improved uranium recovery, at least in a South African (Witwatersrand) context.

Jan 1, 2014

By M. Chettibi

The interaction and galena flotation with xanthenes and dexanthogen regularities have been de-fined. So, using thermodynamic method of analysis, the thermodynamic stability of [galena - xanthenes - water] system and the behavior of lead xanthenes surface state in solution were devised. Thus, results of cared out calculations and experimental investigation completely coincide with-out depending on witch product of sulfur oxidation is formed in the solution. In additional, was obtained quantitative physico-chemical models for the necessary xanthenes concentration of lead sul-fide complete flotation in the tuning fork of: at ?? values from 7.0 up to 9.0 (or at the formation of lead carbonate PbCO3 ) and at ?? values from 9.0 up to 12 (or at the formation of lead hydro carbonate Pb3(OH)2(CO3)2 Physico-chemical models derived can be used as the criteria for functional units of automation systems to control and regulate the flotation process in mineral processing plants.

Jan 1, 2014

By I Brum

Brazil and Colombia have large reserves of coal, those reserves in Brazil are located predominantly in the south and Colombia the main reserves are located in the north. Despite the relative ease of exploitation, these resources have been underestimated as a source of energy. Currently, these countries are developing projects and partnerships aiming to qualify this mineral resource, adding quality to the final product of the processing plants. In this scenario the processing of Brazilian and Colombian coal in flotation columns appears as a promising alternative, having been successful in mineral systems containing fine particles This paper aims to study the overall process of column flotation for a specific Brazilian coal and a specific Colombian coal. The material used in this study consists of fine coal from Brazil (Copelmi) and Colombia (Cerrejon). The objective is to recover carbonaceous matter and reduce the ash and contaminants grade. The two coals were floated using a negative bias in a 5 cm diameter conventional flotation column of 5 m high. Flotation parameter investigated included air velocity in the range 0.6 to 1.5 cm/s. For all runs, a constant negative bias of -0.25 cm/s and a pulp concentration of 8% w/w were used. For Cerrejón coal, 300 g/ton of frother and 907 g/ton of collector was used, whereas for Copelmi coal, 600 g/ton of frother and 1815 g/ton of collector was employed. The frother was a commercial Aerofroth 65 (AF65), whereas the collector was Kerosene. For the Colombian coal, in general, yield, organic recovery, ash recovery and water recovery decreased with the increasing air rate. However, for Brazilian coal the air rate had no significant effect. For Colombian coal, the highest yield (60% w/w) and organic recovery (69% w/w) were obtained at the lowest air rate (0,6 cm/s). Keywords: negative bias, column flotation, coal

Sep 1, 2012

By T. Tumidajski

The purpose of the separation processes in coal processing is obtaining products of certain ash contents. In the most of cases it is assumed that the separation process is described by one, selected parameter, which usually is grain size or material density. The separation may be described by means of statistical distributions of random variables, what allows forecasting the separation results of certain enrichment method. There are very well known the applications of approximations of Tromp separation curves or distribution functions of Erasmus, Meloy or Weibull. It is necessary to say that if the fitness of the approximation more suitable, then the characteristics of the process itself is also better. In purpose of obtaining more appropriate results, these methods were modified by application the mathematical functions, as i.e. hyperbolic tangens function. Furthermore, on the basis of empirical data, so-called interpolations may be performed in purpose of getting more appropriate results of approximation. One of the most known techniques of interpolation is Hughes method. This method for interpolating standard data involves breaking down each interval into a number of smaller sub-intervals. The results of such one-dimensional approach not always contain the full in-formation of the searched distribution. It happens because such interpretation of the problem is not completely correct. In practice, the separation process depends not only on the one parameter (i.e. grain size), but also on many other features characterizing certain material (i.e. its density). It seems then that in some cases the application of multidimensional grain characteristics distributions will be more appropriate. In this paper, the technique of joining the distributions of grain size and density by means of so-called Morgenstern distributions is shown. The general form of these distributions is as following:

Jan 1, 2014

By M. M. Kulkarni1

Kaolin clay is used as a filler and pigment in various applications such as paper, paint, rubber, plastics, adhesives, ink and ceramics etc. Major mineral content in crude kaolin clay is kaolinite along with some accessory minerals as quartz, hematite, mica, feldspar, anatase, rutile, illemnite etc. The Fe and Ti bearing minerals play very important role in determining quality of the kaolin, as these minerals impart yellow, pink or darker color to the white kaolin. Conventional beneficiation methods used in kaolin processing are de-gritting, classification and sodium dithionite bleaching, which improves the optical properties of kaolin, wherein reduction of color imparting constituents such as Fe2O3 and TiO2 is marginal. In the present study, these coloring impurities are separated using selective adsorption of water-soluble polymers. Degritted kaolin samples after passing through 45 micron sieve is used in the study for selective flocculation by polyacrylamide based polymers. The effect of pH, zeta potential, and polymer dose on the reduction of impurities is studied. Analytical tools such as XRF, XRD, SEM, and TEM techniques are utilized and results are discussed in detail.

Sep 1, 2012

By Ming’an Wei, Chuanyao Sun, Zhenguo Song, Zengwen Dou, Yangge Zhu

"The effects of pH value and dissolved oxygen(DO) in the pulp to the Eh and flotation recovery of pyrite were investigated using potential online detection system. The effects of DO on the Eh and flotation recovery were tested which DO changed from 0.5mg/L to 19.5mg/L in six different pH buffer flotation systems (pH: 4.00, 5.62, 6.86, 9.18, 10.01 and 10.96 respectively). Results of potential detected online demonstrated that the pyrite electrode has nearly the same response to potential as with platinum electrode for the FeS2-xanthate-H2O flotation system under the study conditions. Pulp potential and recovery of pyrite were remarkably influenced by pH, both of them decreased with the increasing of pH and, especially, sharp decreased after pH above 9. As the concentration of DO was increased, the Eh was also increased in all the six different buffer solution, while the flotation recovery was decreased. And the amplitude of variation for Eh was not obvious in acidic and neutral solutions, but on the contrary, the change for flotation recovery was remarkable in neutral and alkaline conditions. This may indicate that the flotation of pyrite will be deteriorated in alkaline and high DO concentration conditions."

Jan 1, 2014

By M. Saghaeian, R. Hejazi, L. Hosseini

The specific surface area (Blain value) of iron ore concentrate entering the pelletizing plant is one of the characteristics most effective on the overall performance of the plant such as producing harder pellets, decreasing additives consumption, and decreasing energy consumption. Therefore, preparing the feed entering pelletizing plant is required. The iron concentrate entering Ardakan pelletizing plant located in Yazd province, Iran bears relatively low Blain value (approx. 1600 cm2/g) which necessitates one stage of regrinding so as to increase the Blain value to more than 1800 cm2/g. Studies were conducted and results showed that HPGR is the best regrinding equipment for increasing specific surface area. Conducting pilot plant tests on the concentrate sample revealed that specific throughput is 181 to 263 ts/hm3 and specific energy consumption is 1.6kWh to 2.2 kWh. Pilot tests also showed that one stage of grinding results in 407 cm2/g to 553 cm2/g increase in specific surface area. Based on these results, diameter of rolls, length of rolls, power consumption and grinding force were calculated to be 1.3 m, 0.9 m, 1276 kW and 13800 kN, respectively. Therefore, an HPGR with a roll diameter of 1.52 m, roll width of 1.1 m, power of 1660 kWh and a capacity of 500 t/h has been selected and implemented in Ardakan pelletizing plant. Industrial performance of HPGR and its effects on the plant study results show that limestone and bentonite consumption has reduced about 60% and 30%, respectively. Total Fe of the final pellet has increased from 65.5-65.7% to 66.2%. Cold compressive strength (CCS) and porosity of final pellets are approximately 292 kg/pl and 20.4, which are in the acceptable range.

Jan 1, 2014

By H. R. Manouchehri

The importance of the grinding environment and its effect on sulphide minerals flotation behavior has been known for many years. The grinding environment may play a role in controlling fine and coarse particle flotation along with dissociation of different chemical species in grinding environment. Dissociation of different chemical species and ions within the process water may result from changing the grinding environment. The mining and mineral processing industry undertakes activities that may impact on water resources. These include use and storage of chemical storm-water management, process water management, mine dewatering and management of tailings. In mineral flotation understanding and controlling water quality is paramount important not only because of its effect on flotation but also with respect to control the quality of the water which is released to the environment. Releasing of different anionic and/or cationic chemical species in the process water results from the interactions among different mineral within the ore, process water, and the milling environment. In fact grinding mill acts as an electrochemical reactor which affects the flotation performances of different value minerals as well as the quality of the tailing products. An increasing in antimony content in process/discharge water at Boliden?s Tara processing plant in Ireland to above limitation level was reported in April 2010 which needed to be controlled. An increase up to 6 times of the permitted level was reported which needed an immediate action to control due to environmental considerations. Therefore attempts were made to detect why this higher amount of Sb is released and how to control and minimize its release to the process/reclaim water. This paper discusses how/why Sb content in process/reclaim water was increased by changing the mill electrochemistry and the strategies were taken into considerations to control it. Different strategies, including electrochemical controlling of the milling section, Fenton process, using Bauxsol in treating the process water, etc., have been considered and tested which are described herein. All strategies taken into consideration for solving the problem were successful which indicated good understanding of the issue and good decision making. Furthermore, for each solution the capital and operational costs were roughly estimated. Accordingly, the Sb content in process/discharge water was controlled to a value lower than allowed limitation, i.e., 1 ppm. Keywords: antimony, water contamination, mill electrochemistry, ag milling, grinding media, eh-ph, sulfide minerals, fenton process, bauxsol, lime addition

Sep 1, 2012

By W. M. Zeng

A mixed culture of moderately thermophilic microorganisms was enriched from Acid Mine Drainage (AMD) samples collected from several chalcopyrite mines in China,which can leach copper from chalcopyrite effectively. Its tolerance to chalcopyrite was brought up to 80 g/L after being adapted to gradually increased concentrations of chalcopyrite. The effects of several leaching variables on copper recovery in Stirred Tank Reactor had been investigated. The ore contained chalcopyrite (62.2%) and galena (25.6%) as the main sulfide minerals. The results of the tests show that it is possible, operating at 8% of pulp density to attain copper extraction of 75% in 44 days. The leaching rate of chalcopyrite tends to increase with the dissolution of total iron. Microscopic counts of microorganisms in the solution tend to be higher at low pH range. Furthermore, the analyses of leached residues indicate that the passivation of this chalcopyrite is mainly due to the formation of a mass of jarosite and anglesite (about 48.3% and 21.7% in residue respectively), other than elemental sulphur layer. The bacterial community composition was analyzed by using amplified ribosomal DNA restriction analysis (ARDRA). Two moderately thermophilic bacteria species were identified as Leptospi-rillum ferriphilum and Acidithiobacillus caldus, with different proportion in the bio-pulp, 67% and 33%, respectively.

Jan 1, 2014

By Mingfei He, Xianyang Qiu, Hongling Wang, Yude Gao, Qingbo Meng, Xiaoping Xu, Hao Bu, Guosheng Wang

"By the “HGMS-gravity separation-Flotation” combined technology, a Ta-Nb-Sn concentrates with the grades of Ta2O5 10.00%, Nb2O5 9.13% and Sn 42.62% at the recovery of 44.73% , 9.13% and 14.62% respectively , a Li concentrate with Li2O 3.11% at the recovery of 51.83% and a feldspar product are obtained. All the value elements are recovered. INTRODUCTION Tantalum and niobium widely used in electronics, atomic energy, aerospace and chemical industries with the advantages of high melting point, good ductility, low vapor pressure, strong corrosion resistance and high thermal conductivity are important strategic resources which occupy a special position in rare metals (Crockettand, 1993; GAO and Zou, 2004; LI and HUANG, 2012). China's tantalum and niobium resources are poor, and most of them are low grade, fine grain size, complex composition, and polymetallic associated with refractory mineral resources (GAO and Qiu,2013; Liang and Li, 2016). The Yifeng Lion Ore containing lithium and other rare metals (tantalum, niobium and tin) is an important lithium polymetallic deposit in China Jangxi province. While extensive previous studies have settled on the recovery of lithium minerals by flotation only for the extremely low grade of Ta, Nb and Sn. The regular gravity concentration is used, and the recovery of tantalum niobium is low. This paper sets out to investigate a combined flowsheet of “high gradient magnetic separation (HGMS),-gravity separation-flotation” to effectively comprehensively recover the Li, Ta, Nb, Sn and the feldspar resources in the Yifeng Lion Ore.ORE PROPERTIES Chemical analysis The run of mine comes from Jiangxi Yifeng Lion ore. The main elements of the ore chemical analysis results shows in Table 1. From Table 1, the grades of lithium and rubidium are relatively high, but the grades of tantalum and niobium are lower than the industrial grade; feldspar with high content of potassium and sodium and low content of iron can be used as high-quality ceramic raw materials."

Jan 1, 2018

By Jyotirmoy Sarma

The surface-active agent, like sodium humate, in the present systems produces a very stable suspension. Saline water up to 15% is used as a flocculating agent for recovery of water from the dispersed phase containing 1% solid. The recovered water in the presence of humate at different concentrations (0.05-0.2%) and at pH 8 also produces a stable dispersed phase of iron ore fines and tailings. The beneficiation techniques adopted in the present systems can increase ~ 2-3% iron value in the concentrate of iron ore fine, however, for tailings the increase in iron value is not observed. Keywords: beneficiation, flocculation, iron ore fines, tailings, saline water, surface-active agent

Sep 1, 2012

By Q. J. Liu

The flotation circuit and the reagents of the all-sliming flotation about low grade and hard operation on zinc oxide ore are researched in the paper. The results indicated that there are many types of zinc minerals in this ore, and the composition is very complex. They include hemimorphite, smithsonite, hydrozincite and so on. The ore is seriously sliming. In light of the ore properties, three kinds of flowsheets have tested. They are gravity concentration (cleaning tables), flotation, combined process of gravity concentration and flotation. The test showed that the recovery of zinc is only 17.08% in the gravity separation. In combined process of gravity separation and flotation, the recovery of zinc concentrate is close to 70%. But the flow-sheet is complex and hard to control in the production. The floatation circuit is feasible. In the test, it pay attention to investigate the new combined reagent which is used in selective all?sliming flotation process. The effects of slime are eliminated by the multi-loop treatment of middling. In flotation, the final recovery of concentrate is 88.76%; the grade is 29.50%. The recovery of physical ore is 93%; and the recovery of -10mm fraction is more than 65%.

Jan 1, 2014

By Z. B. Pan

The innovative point of this new technology can be described that under normal pressure and 70°C, using a new combined activating and oxidizing agent, the minerals bearing arsenic and organic carbon are oxidized effectively. This technology can be applied in commercial scale. The high carbon and arsenic bearing gold ore is taken from Gansu, where hundreds of tons gold deposit. The ore has 0.51% of arsenic and 1.75% of carbon (1.07% of organic carbon). The gold occurs mainly in native with particle size 0.02~0.6 mm and a few are enwrapped by pyrite and arsenopyrite. The traditional cyanide leaching process gains a very low gold leaching rate with only 5%. Through systemic experimental study, the technological flowsheet of flotation process for concentrating gold, then pre-treating the gold concentrate followed by cyanide leaching the gold concentrate are used. With 4.92 g/t gold of head sample, the gold concentrate with 46.52g/t gold grade and 96.53% gold recovery is gained by flotation process. Followed by pre-treatment for 6 hours, the gold concentrate is leached with cyanide after filtration and washing. The total gold leaching rate is up to 95.44%.

Jan 1, 2014

By Y. F. Hou

This paper reports the results of the study of the influences of concentration and modulus of sodium potassium silicate solution (Na-K activator) and curing mode on the phase composition, mi-crostructure and strength development in the geopolymers prepared using Class F fly ash. X-ray dif-fraction (XRD), Fourier transform infrared spectroscopy (FTIR) and MAS NMR are utilized in this study. It shows that the compressive strength increases while sodium potassium silicate solution modulus increases, but when modulus exceeds 1.7, the compressive strength decreases, and it decreases markedly while modulus is greater than 2.0. The compressive strength improves with increase of sodium potassium silicate solution concentration. When the concentration is 36%, the compressive strength reaches the maximum. Elevated temperature can increase the strength of samples synthesized using sodium potassium silicate solution with 32% concentration and modulus 1.2. Compared to the strength of the sample cured at 50?, the strength of the samples cured at 65? and 80? are higher at 1 day and 3 days, but when cured at 80?, strength is smaller than that cured at 50? for 7 days. When temperature is too high, too long curing time will decrease the strength. Long precuring at room temperature before application of heat is beneficial for strength development, and there is about 10%~50% increase in strength of the samples cured at 1 day precuring and 2 days elevated temperature as compared to the strengths of the samples cured for 3 days at elevated temperature or cured for 28 days at room temperature. The main product of reaction in the geopolymeric material is amorphous alkali aluminosilicate gel.

Jan 1, 2014

By Robin J. Batterham

The Bologna Process started in 1999 with a declaration signed by ministers from most European countries. As of 2012, the Bologna Process now has 47 participating countries (EHEA 2012). Overall, the Bologna process has demonstrably changed higher education in many countries to allow for considerably more flexibility in course offerings. Keywords: bologna model, education

Sep 1, 2012

By Arkady Senchenko

At present, there are different traditional and modern methods for ore grindability evaluation. The correct and rational approach to sampling, testing methods and mill sizing enables one to design a workable technology. This paper contains TOMS institute experience in different grinding indices determination over the last 7 years (SAG Design Test, BWi, CWi, RWi, and other). Mill sizing examples and circuits modeling for the projects in Russia and Kazakhstan are considered. Keywords: ore grindability, SAG Design Test

Sep 1, 2012