Search Documents

By H. Harzer

Statistics Canada record s indicate that in recent years 70 to 80% of the entire Canadian coal production originated from Western Canadian mines, in which about 55 to 65% of the coals are bituminous. Until recently, less than 20% of the latter were extracted by underground methods , the remainder being surface-mined. However, it is estimated that within the foreseeable future up to 80 or 90% will have to be gained by underground techniques. Although Western Canadian coal resources are considerable, they are unfortunately locked in severely distorted, steeply pitching and faulted seams of variable thickness. Consequently, their economic extraction poses serious engineering problems. One possible solution to the problems is to apply hydromechanical methods to underground mining. This is a well-proven method shown to be economically viable under Western Canadian conditions. This paper endeavours to widen the scope of published data on hydraulic coal mining and is based on practical engineering and cost data gathered through contacts with West German designers and operators of hydraulic mines.

Jan 1, 1978

By Paul Clark

Generation - Profile l 9,726 megawatts (MW) of capacity l 46,877 gigawatt hours (GWh) produced at an average plant availability of 88.4% l 47 facilities in four geographies: Canada; the U.S.; Mexico; and Australia l Fuel mix of coal (62%), gas (26%), hydro and renewables (12%) l 23.2 million tonnes of coal mined l 47.0 million gigajoules (GJ) of gas consumed

May 1, 2004

By Staff

Introduction As the Sherritt Gordon property is still in the development stage, . it is rather difficult to write a proper account of the mining methods and milling practice that will be used. While the general scheme of operation will remain the same, there will undoubtedly be many minor changes to meet special conditions which we cannot forsee at the present time. Most of the work accomplished to date has followed the usual routine of preliminary development in the Canadian North. However, we have learned a few things which might be of use to others operating under similar conditions. The most important of these is the saving in power cost made possible by the use of Diesels as against steam power when using wood fuel, and the movement of freight by tractors when rail transportation is not available. Location The property i6 located about 90 miles north of The Pas, or 40 miles northeast of the Flin Flon mine. A branch line from Cranberry Portage, on the?C. N. railway, between Flin Flon and The Pas, connects the property with the outside.

Jan 1, 1930

By R. D. Lindsay

"Pamour Porcupine Mines, Limited is involved in the mining, milling and primary refining of various gold, gold - copper and refractory gold ores. Pamour operates five mines in the Porcupine Mining District of Ontario, and two 2,550 t/d milling facilities.Both metallurgical facilities use conventional cyanidation technology including zinc cementation for precipitation of gold and silver from solution. The precipitation process, as applied to clarified leach solutions (less than 1 ppm suspended solids) at Pamour is called the Merrill - Crowe process. Precipitates from both milling operations are treated at Pamour's Area Refinery. Schumacher precipitates, unlike Pamour No. 1, require an ''Acid Treatment Stage"" prior to refining to remove the high contained copper. This is accomplished by leaching the precipitates initiallv with sulphuric acid to remove zinc and then with sulphuric acid and manganese dioxide to dissolve copper. Refining procedures after ''Acid Treatment"" are essentially the same for both precipitates.The following considerations highlight the basic principals applied to refining cyanidation precipitates at Pamour, including:"

Jan 1, 1986

By P. R. Geoffoy, T. Koulomzine

"The discovery of the Mogador deposit concealed by 100 feet of overburden was the result of combined application of geological reasoning, ground geophysical surveys, studies of glacial float and extensive diamond drilling. The ground was acquired because it lay on the projected intersection of the Manville and Laflamme River faults. Systematic ground prospecting led to discovery of mineralized floats. A first unsuccessful exploration campaign lasted several years and consisted of 137 drill holes.In 1951 the boulder nests were reexamined and an associat'on of the mineralized float with boulders of a granodiorite, unknown in outcrops of the district, was established. Consequently, ground magnetic surveys were extended and re-interpreted, and a large anomaly interpreted as corresponding to a batholith was outlined. The existence of the batholith was immediately confirmed by drilling and the Mogador deposit discovered in third hole of new drilling programme in a zone of fractured volcanics paralleling southern contact of batholith.The Mogador deposit is a complex replacement of silicified volcanics by pyrite, pyrrhotite, sphalerite, chalcopyrite and galena carrying values in silver and gold. A total of 1,230,000 tons has been indicated, most of it now classified as fully developed proven ore."

Jan 1, 1960

By Rob Sloan, Simon Yu, Rob Robison, Mark Schmidt

"In 2000-2009, Highland Valley Copper (HVC) tested new generation 660 mm cyclones supplied by various manufacturers in an aim to replace existing first generation 762 mm cyclones without success. Due to plant infrastructure limitations, new generation larger (838 and 800 mm) cyclones were not feasible. In 2010, an approach of testing hybrid 800 mm diameter cyclones was initiated by HVC. The hybrid cyclone consists of an 800 mm cyclone upper head section and the use of existing 762 mm cyclone conical sections. Three hybrid 800 mm cyclones were engineered and fabricated, targeting a throughput of 850-950 mtph and were installed in the E line cyclone cluster. Since starting operation on September 20, 2011, three hybrid 800 mm cyclones have been running at combined throughput ranges of 750 to 1050 mtph. Based on plant Daily Met Reports, the test hybrid cyclones demonstrated a decrease in misplacement of coarse copper bearing material to the cyclone overflow and better cyclone efficiency when compared to the existing 762 mm cyclones at the same throughput. The hybrid 800 mm cyclones also demonstrated significantly higher capacity per unit when compared to the existing cyclones. Based on the improvement demonstrated in the full plant trials, HVC decided to install the new hybrid 800 mm cyclones in all five grinding lines starting in July, 2012. A more detailed discussion of the full plant trials and initial results of the first complete retrofit of E line will be presented. INTRODUCTIONHighland Valley Copper Partnership (HVC) is Canada’s largest base metals mine and one of the world’s largest producers of Cu-in-concentrate. The mine, located in the central interior of British Columbia, is owned (97.5% interest) and operated by Teck Resources Ltd. In 2011, HVC produced about 210 million lbs. of Cu and 8 million lbs. of Mo. HVC’s Mill Modernization Project (MOP), which was budgeted for $475 M, is currently under intensive construction and is scheduled for commissioning in Q1 2014. The following description was valid at the time of writing this paper.The operation has been expanded a number of times since the startup of the original Lornex mill in 1972. The plant started up with two 9.75 m (32 foot) diameter primary SAG mills. It was expanded in 1981 with the addition of a 10.36 m (34 foot) diameter SAG mill. In 1988, the Highmont concentrator grinding mills and flotation section were moved and attached to the Lornex mill site. This added two10.36 m (34 foot) diameter AG primary mills to the Highland mill. This brought the total number of primary mills to five referred to as Line A, B, C, D and E: three SAG mills (A, B and C) each with two ball mills in parallel and two AG mills (D and E) each with one ball mill. Each AG mill line is equipped with one short head pebble crusher. Ball mill circuits are classified using 8 clusters of ten Linatex 762 mm cyclones to reach a target P80 330 micron (equivalent 43% +100 mesh), before the cyclone overflow product advances to the bulk flotation circuit."

Jan 1, 2013

The uphole bench extraction strategy at EKJV Management Pty Ltd?s Raleigh Mine, requires simultaneous horizontal and vertical exposure of paste filled stopes. In order to prevent excessive ore dilution, the paste fill must be of sufficient strength to prevent failure during exposure. A numerical modelling methodology has been developed to accurately simulate the initial stress distribution within paste filled stopes, together with the strain-softening loading response of paste fill material. Due to the narrow orebody width and high deformation behaviour of the host rock mass, high closure strains are likely to cause a stiff, brittle fill material to undergo crushing failure upon exposure. The stability of paste fill exposures at the Raleigh Mine was determined by conducting a series of three-dimensional numerical models that incorporate the extraction, filling and exposure sequence of paste filled stopes. Stability charts for 2.5 m and 3.5 m wide simultaneous horizontal and vertical exposures have been derived based upon the numerical modelling results. Implementation of the stability charts has proved successful in limiting the amount of ore dilution from paste fill and provides a basis to optimize paste fill cementation and stability throughout the life of the mine.

May 1, 2007

By D. Gendzwill, N. Martin

"In early 1987, the Patience Lake potash mine near Saskatoon, Saskatchewan, was closed due to uncontrollable floodingWater inflows were first encountered during routine mining in 1975 at the south boundary of the mine lease. Underground grouting and construction of bulkheads limited the flo but did not completely stop it. Subsequent seismic surveys showed that the mine had approached the edge of a large collapse structure in which the salt and potash had been partly dissolved and removed by groundwater.In 1986, the small flow into the mine started to grow. Despite renewed grouting, the flood increased and outstripped pump capacity. The grouting program temporarily slowed the inflow but was unable to stop it. Eventually, from seismic and drilling evidence, it became clear that the water source was an extensive system of vertical fractures which would be impossible to seal by drilling and grouting from underground. A new plan to install 14 bulkheads underground would have sealed the water source from the rest of the mine but the construction program could not be completed before rapidly increasing inflow threatened to fill the mine. The underground mine was closed and a new solution mine started in 1988."

Jan 1, 1996

By G. E. Agar, W. B. Kipkie, R. A. Tenbergen

"This paper describes the successful pilot plant testing of a flowsheet, developed at INCO Ltd.'s J.Roy Gordon Research Laboratory (JRGRL), for improved separation of the constituent minerals in a bulk copper nickel concentrate.The flowsheet utilized the fact that xanthate concentration on the mineral surfaces is the most important variable affecting the high lime separation and that reduction of the xanthate concentration could be effected by an oxidative conditioning stage.When the adsorbed xanthate was reduced to a suitably low level, chalcopyrite and pyrrhotite could be floated to leave a high grade nickel concentrate as the residue. Sodium cyanide was added to the froth product to depress pyrrhotite and any remaining pentlandite. The temporary depression of chalcopyrite by the sodium cyanide was overcome by introducing a conditioning step following cyanide addition. The advantages of the flowsheet; improved copper-nickel separation, operation without heating of the pulp, production of both high grade nickel concentrate ( 29. 5% Ni, . 26% Cu) and copper concentrate ( <O. 5% Ni, 30% Cu) were all realized."

Jan 1, 1984

By A. G. Doll

"This paper expands the SAG mill survey database published by the Author at Procemin 2013. The new database includes 49 published SAG/AG mill surveys and includes mills from all over the world. The paper will compare the survey database to SAG mill models by Austin, Morrell and Hogg & Fuerstenau with the purpose of demonstrating the degree of fit of the models to surveys and validating any empirical “fitting factors” used in the models.SAG mill power draw models are used in mill design and grinding circuit modelling to predict how much power will be consumed by a particular mill geometry and operating configuration. The importance of conducting surveys suited to model calibration will be highlighted because the review of literature shows that survey information important to modelling is often missing or omitted. A recommendation for the collection of data during a mill survey is presented, along with some assumptions used by the Author in the absence of certain data. The benefit to mining companies of publishing their survey data, and thereby allowing modellers to improve their model calibration, is discussed.The comparison of models requires a discussion of the measurement of power in a mill drive system as the models use slightly different position in the electrical network for ""where power is measured"". The benchmarking of models against plant operations requires a similar discussion of power measurement."

Jan 1, 2016

By S. H. Ward

An account of a new method of investigating the electrical .properties J the earth&apos;s crust is presented. The method, called AFMAG, employs, as a source, natural alternating magnetic fields of audio and sub-audio frequencies. Measurements of the distortion of these fields caused by geological features are made with the aid of search coil detectors at several discrete frequencies. Many results of field surveys made with the method are presented and they illustrate its advantages and limitations when applied to the search for massive sulphide mineralization. The advantages far outweigh the limitations and in fact indicate that a major breakthrough in geophysical exploration technique and instrumentation has been made.

Jan 1, 1958

By Benedetto Corain

The production and dispersion of metal nanoclusters onto inorganic supports and amorphous carbon rest on well consolidated technologies belonging to the realm of industrial catalysis and of basic catalysis research (1). In spite of the existence of a variety of specific synthetic strategies, their very rationale relies on three main approaches i. e.: A: precursors of both the metal nanoparticles and of the relevant supports (or the support itself) are intimately mixed (even let to react) at ambient conditions and then thermo-reduced according to very controlled protocols (2); B: precursors of metal nanoclusters are let to be adsorbed onto suitable supports from the gas or liquid phase and subsequently thermally decomposed (3); C: metastable size-controlled metal nanoclusters are previously generated in a liquid medium and subsequently transferred onto pre-formed support particles (4). The production and dispersion of metal nanoclusters onto organic soluble supports is also a rather well documented academic praxis (5, 6, 7, 8) able to provide e.g. size-controlled Au0 nanoclusters of 4.4±1.7 nm (5). Our group started in 1997 developing (9) an innovative approach to the synthesis of metal nanoclusters dispersed inside insoluble, albeit accessible (see below) mechanically robust gel-type resins (10), which procedure was tested so far on palladium metal. Metal ions are previously dispersed upon ion-exchange inside of the polymer framework, followed by chemical reduction and by the aggregation of born metal atoms into nanoclusters, the size of which is templated (11, 12) by the three-dimensional intercommunicating meshes that build up the overall polymer framework (Figure 1).

Oct 1, 2003

By Ted J. Williams

Underhand cut and fill mining methods are used at the Lucky Friday, Stillwater, and Galena mines in the western US in an effort to safely mine in difficult ground conditions and as a primary mining method where access below the ore is limited. The method has evolved at each mine to meet the unique situations associated with their milling procedure and mine layout. Details of the operational aspects of the backfilling and mining cycles at each mine are presented in this paper, accompanied by a summary of the mechanical properties of the backfill and its in-situ geomechanical behavior.

May 1, 2007

By P. Radziszewski

"The comminution energy curve is a profoundly simple graphical technique that displays detailed operating efficiency information for industrial comminution processes. The database underlying the methodology has recently more than doubled, to now contain a substantial fraction of the international comminution output (1.7 billion tonnes of rock per year) across more than 8 major commodities. This increase has deepened the analytical capabilities and effectiveness for assessing comminution circuit performance in relation to comparable operating mines. This paper will explore how the energy curve methodology can be used to examine the ability of stirred mill technologies to increase efficiency.Specifically, this paper explores how the energy curves methodology can be used to present energy efficiency gains achieved at three mines employing a stirred mill technology under different duties. The first of these cases studies was conducted by Rosa (2014) who compared the performance of two ball mills operating in parallel with a Vertimill in the regrinding circuit at the Samarco Iron project in South East Brazil. The Vertimill was found to achieve the same product specification while consuming 40% less energy. Brissette (2010) investigated the impact of grinding media on the performance of both ball mills and Vertimills. The energy savings achieved varied from 10% to 40% for the ball mills and 30% to 60% for the Vertimills. Lastly, Bergerman (2012) investigated the operating conditions of the Sossego regrind circuit from 2006 to 2011 against design specifications and laboratory testing. The operating work index of this circuit varied from 5.2 kWh/t to 44 kWh/t over this 5 year period. The full suite of energy curves"

Jan 1, 2016

By D. Eastick, S. Hardcastle

"Over the last few years, a multi-faceted feasibility study has been evaluating the introduction of hydrogen fuel cell-powered equipment into underground mines to replaced diesel engine-powered equipment. The analysis has shown that under normal operating conditions fuel cells could at the very least be an environmental and health benefit by eliminating combustion engines and their unwanted by-products. However, they could also generate significant reductions in the amount of ventilation a mine needs to supply when compared to dieselized operations; this would further decrease a mine’s energy consumption, its associated greenhouse gas impact, and also reduce a mine’s significant ventilation-associated costs. Fuel cell-powered equipment also has the advantage of lower noise and heat production compared to its equivalent diesel-powered counterpart.The degree to which fuel cells can generate ventilation benefits in underground mines depends upon a number of operational parameters and mine specific qualifiers such as current ventilation control or management, mine depth, inherent dust conditions, and minimum velocity requirements.However, another major consideration in the introduction of fuel cells in underground mines will be the safety requirements associated with diluting and removing the potentially explosive hydrogen in the event of a gas leak. In outside surface applications, it is possible to use dispersion, buoyancy, time, and lack of ignition sources as mitigating factors in deriving a low risk of an explosion. However, in underground operations, these factors change, and dispersion and buoyancy are limited; time may not be available and, in non-coal mines, ignition sources are not typically controlled. When a hydrogen leak occurs, the availability of sufficient ventilation to dilute and effectively remove the gas will be critical. Consequently, ventilation may be the prime risk controlling factor. In this paper, the authors evaluate the potential benefits of replacing diesel engines with fuel cells in powered production equipment, discuss the mitigating qualifiers that could limit ventilation savings, and evaluate solutions to retain and maintain an additional ventilation capacity in the event of an emergency situation, such as a hydrogen leak from the fuel cell stack or its distribution system."

Jan 1, 2007

By Chris Bennett, Glen Kosick

"Process modeling and equipment sizing procedures for SAG circuits has advanced significantly over the past two decades. However, no matter how exact the hardness tests, models and scale-up calculations, if the ore samples being used for design do not accurately represent the orebody then major design errors can be encountered. This paper will describe a hardness testing method for identiQing the power requirement profile of an orebody, to an extent that design errors due to poor sampling can be greatly reduced or avoided altogether. It will provide some insight into the magnitude of hardness variability that can be encountered in an orebody. Finally, the paper will preview how detailed hardness distribution data can be incorporated into mine block models, to optimize SAG circuit design for an orebody, both fi-om a capital investment and throughput point of view.INTRODUCTIONIt has long been known that many SAG/AG' circuits experience wide swings in throughput. These throughput variations are almost always of a magnitude not anticipated in the plant design; consequently, they are detrimental to the expected return on investment for the mining companies. It is clear that the throughput swings are mainly caused by changes in ore hardness. In 1993, in an attempt to address this problem, MinnovEX began investigating the possibility of using a small scale SAG test (2 kg charge) to predict SAG power requirements from drill core samples. The objectives of the small scale test were to enable mining companies to do many more SAG hardness tests than currently undertaken for a particular orebody. To make this possible, the SAG tests had to use a minimal amount of sample, be cost effective, and give acceptable accuracy in the prediction of SAG power. If this small scale SAG test proved accurate, then the high sampling frequency would yield results that approach the true hardness distribution of an orebody. This hardness distribution could then be used to derive the distribution and variability of specific energy required throughout the complete orebody. This specific energy (kWh/t) can be thought of as the power required to grind one tonne of ore per hour (kW/tph) to a specified size. Once the true distribution of power requirement throughout the whole orebody is understood, the grinding circuit design team can make an informed decision regarding the hardness value that is most appropriate for sizing the SAG equipment. Throughput losses due to hardness variation could be deliberately planned for or avoided altogether (a capital cost decision)."

Jan 1, 1999

By J. Shibata, N. Murayama, H. Yamamoto

As one of effective usages of wastes discharged in the non-ferrous metal industry, the syntheses of AlPO4-5 and hydrotalcite were carried out using aluminium dross as a raw material. AlPO4-5 is an aluminium phosphate condensate with properties of zeolitic materials and large pore size. Hydrotalcite is an inorganic anion exchanger and has a layered structure of complex hydroxide. They were synthesized in an autoclave at high temperature and pressure. Various physical properties such as crystal structure, surface texture, and specific surface area were measured. AlPO4-5 can be synthesized from aluminium dross under hydrothermal conditions at 180°C-200°C, and 3h. At the same time, AlPO4-34 and non-porous AlPO4 were also formed as by-products. The crystals of AlPO4-5 have a hexagonal structure. Lt is desirable to heat the reaction product at around 550 °C to remove tri-ethyl amine. The specific surface areas of the reaction product before and after heat treatment at 550°C were 17.9m2/g and 358m2/g, respectively. Hydrotalcite can be obtained by a co-precipitation method from the aluminium dross and waste MgCl2 solution discharged in the aluminium regeneration process. Small amounts of SiO2, Al2O3, and Fe2O3 remain in the reaction product as an impurity component. The interlayer distance of the obtained reaction product is about 0.3 nm. Hydrotalcite changes to Mg-Al oxide during calcination at 500 °C for 3h, and then hydrotalcite is formed again by a rehydration operation. The physical properties of the reaction products obtained from the wastes were very similar to those from fresh reagents.

Jan 1, 2004

By Nicholas Macrae Steven

Abstract - The Shaba-type Luamata Cu-Co(-Ni) deposit (11°50_S, 24°28_E) is located in a tectonic slice of Katangan Roan Supergroup (Mines Group) sedimentary rocks, surrounded by younger Kundelungu Supergroup lithologies in the external fold and thrust belt of the Lufilian Arc. Luamata is a classic central African copper clearing in dense woodland, visible as a tonal botanical anomaly on Landsat imagery. Supergene Cu-Co mineralization (especially malachite and subordinate chalcocite, digenite, covellite, and copper and cobalt oxides) and, probably hypogene, bornite, and chalcopyrite are hosted by altered, but essentially unmetamorphosed, moderately dipping, dolostones and dolomitic shales. Alteration products include talcose dolomite, sericite rocks and intense silicification and brecciation. Friable yellow shale is best mineralized with cobalt (up to 0.43 wt%), whereas, highest copper grades occur in brecciated, silicified shale (up to 13.5 wt% CuO). Soil copper and cobalt contents are up to 2.2 and 0.6 wt%, respectively. A newly identified nickel zone (where soil contents exceed 0.1 wt% Ni) fringes the Cu-Co deposit. Polymictic, matrix-supported breccias with a calcareous matrix that underlie the Cu-Co deposit are interpreted to be fluidization breccias related to thrust tectonics and the emplacement of the Mines Group slice. Although small compared to the Kolwezi district Shaba deposits in the Democratic Republic of the Congo, Luamata exhibits all the classic features of an ore deposit type (with low calcite contents), whose high metal concentrations could potentially be very profitably exploited by low-cost opencast mining and hydrometallurgical recovery methods.

Jan 1, 2000

By Tony Robles

"A new process is disclosed for the recovery of gold and/or silver values from activated carbon wherein they are adsorbed as cyanide complexes. A unique chemistry allows the new process to use mill process water containing an inexpensive, non-hazardous compound as the eluant. The new process has an elution period of 5 hours at 98°C. The gold in the eluant can be recovered by electrowinning or zinc precipitation. The new elution process is simple, reliable, and provides an eluted carbon that may not require thermal regeneration before reuse. Retrofitting the new process to existing processes such as Zadra, Anglo, and others will not require significant capital expenditures.IntroductionThe efficient and reliable elution process for gold/silver from activated carbon is a very important process in the gold mining industry. The most common techniques for elution of gold cyanide from activated carbon are the Zadra and Anglo procedures.Specialized elution techniques like the Micron and Acetonitrile processes have not been commercialized to significant extent probably due to relatively complex unit operations and expensive reagents.Important functions of the gold recovery circuit are:Efficiently recover gold/silver from the loaded carbon.Carbon is in good condition for reuse for optimum recovery.The pregnant solution is amenable to electrowinning or zinc precipitation to recover gold/silver from the solution.The whole process to be simple and short to reduce gold inventories.Present Elution ProcessesTable 1 shows some carbon elution processes that are available today. The two main elution processes used in the industry are: (1) the Zadra process, in which hot cyanide solution is circulated through an elution column and electrowinning cells; and (2) the Anglo American Research Laboratory (Anglo) process, consisting of a pretreatment step with caustic cyanide solution, followed by elution with deionized water."

Jan 1, 2000

By Paul Billingsley

NICKEL Plate mountain coincides closely with that portion of the Hedley mining district which is of economic interest. From it has come almost the entire past production, and the active mines of the present epoch, Nickel Plate-Sunnyside and Hedley Mascot, lie in a compact group near its summit. The Hedley district, which is 210 miles due east of Vancouver, is situated in the Okanagan range of southern British Columbia, where this rather gentle uplift is deeply dissected by the canyons of the Similkameen and its tributaries. The region is essentially part of the Interior Plateau of the Province (Figure 1), but is adjacent to easterly elements of the Coast Range. The Similkameen canyon, 4,000 feet in depth and frequently less than 4 miles from rim to rim, traverses the district from northwest to southeast. The deepest and narrowest portion of the canyon lies between Hedley and Keremeos, 18 miles to the southeast. At Hedley, an important tributary, Twenty Mile creek, enters from the north in a bold canyon, making a focus of unusually rugged topography. Nickel Plate mountain occupies the sector to the east of this junction (see Figure 2) and its flanks are ringed by the cliffs of Twenty Mile canyon on the west and by those of the Similkameen canyon on the south. On the east, it slopes gently to the hanging valley of Eighteen Mile creek, and on the north, with only slight loss of elevation, it merges into the moderately hilly surface of the plateau.

Jan 1, 1941