Search Documents

By H. Wilton Clark

"IntroductionTHE CANADIAN use of short-period delay-action detonators in coal shooting has been carried on for about two years, mostly in British Columbia, and this is a preliminary report on progress to date. Entire coal faces are being shot successfully with one application of electric current.The electric blasting cap came into use about the beginning of the century. The low-tension electric cap, the type most commonly used, consists essentially of a metal tube containing an initiating explosive. Two wires lead into the end of the cap and are connected inside the cap with a short 'bridge wire .of very high resistance. This •bridge wire is buried in a match-head of a readily ignitable powder composition. When current goes through the lead wires, the bridge wire becomes extremely hot and sets• off the match-head which, in turn, ignites the powder just below it in the tube. This explosion sets off the main charge of explosive. Thus, by connecting a group of caps to a source of electric .current, a number of charges could be exploded simultaneously. This immediately became of great value to mine and quarry operators. Explosives could now be used to break up large masses of material at one time, as against the older, slow method .of blasting small amounts with single charges.The next step was to develop a delay detonator which would allow charges of explosive to fire one after the other, one or two seconds apart. Such detonators allowed first blasts to relieve some rock burden before the next charge fired, giving the second charge an easier task in forcing out more rock, and so on for the rest of the series of charges."

Jan 1, 1953

By Kevin P. Plucknett, Z. Memarrashidi

"In the current work, factors influencing the corrosion mechanisms of TiC and Ti(C,N) based cermets are reviewed. Cermets were typically prepared with 30 vol.% of metal binder, in the form of various in-situ reaction-formed Ni3Al alloys. Commercial WC-Co hardmetals were also examined as baseline materials. The assessment of corrosion involved a variety of electrochemical measurements, including open circuit potential and potentiodynamic polarisation. The corrosion potential and current density were determined, following Tafel extrapolation, allowing estimation of the corrosion rates. Post-corrosion characterisation involved scanning electron microscopy analysis and associated energy dispersive X-ray spectroscopy of the sample surfaces. It is demonstrated that the primary corrosion mechanism for this type of cermet is dissolution of the metallic phase during oxidation attack, and thus this response can be expected to increase with the amount of binder in the cermet, although degradation can be subtly affected by composition (i.e. alloy composition, C:N ratio, impurities in the ceramic phase, etc.) and test procedure (i.e. aerated vs. de-aerated electrolytes). It was observed that addition of N content into the ceramic phase is beneficial to the corrosion characteristics of TiC based cermets, through significant refinement in the grain size of the hard phase. Similarly, elimination of impurities, such as W in selected TiC powders, also improves the corrosion resistance.INTRODUCTION Cermets are prepared using the combination of a hard, high elastic modulus ceramic phase with a ductile, high toughness metallic binder. This pairing of hard and ductile components ensures wide application of cermets in demanding wear environments. These materials are consequently used industrially in both bulk and coating form. The most common example of such a composite system is based on the use of tungsten carbide with a cobalt-based binder (WC-Co), which has been widely examined over the past 80 years. However, while WC-Co has been shown to exhibit an excellent combination of high strength and wear resistance, the corrosion and high temperature properties of this material are relatively poor. In addition, WC-Co possesses a high density (~13–14 g/cm3), which makes it a less desirable option when the component mass is a design factor (i.e. use in aerospace). In particular, the aqueous corrosion response of WC-Co limits its use in wear environments where combined corrosive degradation may occur (i.e. tribo-corrosion scenarios). Alternate cermet systems are therefore being actively developed due to these performance limitations."

Jan 1, 2017

By E. Gervais

"In today's marketplace, heavy competition between materials is the norm. This is particularly true f or the base metals, which are being increasingly challenged by new or improved materials in all traditional applications. Current usage of base metals results from a combination of a metal's intrinsic properties, and technology. The future of the base metal industry rests with innovative, high-quality product development, its ability to take advantage of the results of worldwide, massive material R&D investments, and with the dynamism and effectiveness of its market development programs.The ZA casting alloys program is an illustration of the zinc industry’s efforts to protect and expand its market position in the casting field through state-of -the-art technological developments. The market potential f or these advanced engineering alloys is substantial, and their impact on traditional zinc die casting alloy consumption is particuarly important. The ZA alloys, in offering increased performance through zinc castings produced at low cost and by a wide range of moulding processes, have unlocked a multitude of new end-use applications.Following a review of the development of ZA alloys, of their key properties and of their performance characteristics, the numerous challenges that the alloys present to the zinc industry and to the R&D community are discussed.IntroductionZinc is anodic to steel and has a low, uniform rat e of corrosion; it has a low melting point, can be cast with precision , and is readily finished. In addition to its use in protecting steel and in the production of a wide range of castings, zinc is employed : (1) to produce brass, high-strength aluminum alloys and magnesium die casting alloys, (2) in the wrought state for coinage and in building products, particularly as roofing materials , and (3) as an oxide, in the rubber industry, in ceramics, glass, cosmetics, pharmaceutical products and as the starting materials for many chemicals.Zinc die castings are produced with accuracy at high speed, at low cost, are easily finished and have excel1ent mechnical properties . Car fuel economy, changes in automobile styling, competition from other materials, increased sophistication of design and miniaturization have all led to a dramatic change in the volume of zinc consumed for die-casting applications. This has been particularly notable in the United States. Throughout the 19505 and the I960s, casting was the fastest growing major use of zinc; it was firmly established, accounting for 35% of the total zinc consumption(1), By 1983, the volume of zinc being purchased for casting applications had dropped to less than 20% of all zinc consumed in the United States. In the western world(2), consumption for zinc casting application s is currently at about 15%; being nearly equal to the zinc consumed by the brass industry. Coating applications dominate with a consumption of more than 40% of the total market."

Jan 1, 1987

By A. H. Lang

Introduction The recent uranium discovery at Theano point, lake Superior, is probably a rediscovery of the first reported Canadian uranium occurrence. A description of material from the original discovery was published in 1847 by J. L. LeConte, and many attempts have been made to relocate the deposit. Such attempts have in the past been unsuccessful because of vagueness in the original description of the locality. Besides being a prospect that seems to merit development work, the Camray discovery is important because it reaffirms the occurrence of pitchblende in the eastern part of the Precambrian shield. Much staking followed the announcement of the discovery, and some additional finds have been reported. Location The Camray discovery is at the shore of Theano point, lake Superior, about seventy miles north of Sault Ste. Marie (see Figure 1). It is in township 29, range XIV, district of Algoma. The showing is two miles from Highway No. 17, and is reached by a rough trail that leaves the highway at mileage 72.9 from Sault Ste. Marie. There are no towns of any size nearer than Sault Ste. Marie.

Jan 1, 1949

By E. L. C. Martins, M. J. Nicol, D. Majuste, A. D. Souza

The effects of organic compounds on the current efficiency (CE), morphology, crystal structure and mechanical properties of the metal deposited during the electrowinning of zinc are described. A flotation collector and lubricating oil were selected based on observations made during the industrial production of zinc from silicate ores, in Brazil. The analysis by Fourier transform infrared spectroscopy of these compounds, which may be present in minor amounts in the electrolyte solution, indicated the presence of a polar amine group in the collector, while the lubricating oil is a non-polar compound. The average CE value obtained from organic-free industrial solution was 91.15 ± 0.26 %. The CE dropped to 54.35 ± 0.73 % in the presence of 100 mg·L-1 of collector in the solution, and a negative effect was also observed in the presence of similar amounts of oil (88.84 ± 0.61 %). The characterization of the deposits by scanning electron microscopy and X-ray diffraction revealed the formation of pores in deposits obtained from solutions containing the oil, while a different growth pattern (perpendicular zinc platelets) was identified when the flotation collector was added to the industrial solution. In the presence of these contaminants in the solution, guided-bend tests revealed that the deposits have a higher resistance to deformation, but lower ductility, properties that may affect the performance of the stripping stage. As a result of this work, simple control and optimization actions were applied in the industrial plant, which resulted in important improvements in the electrowinning process.

Jan 1, 2014

By A. P. LeBis

This article attempts to relate the concept of utility to the risk involved when only a small number of projects (compared to their probability of occurrence) are accessible to a firm and to quantify utility when other financial and physical parameters are known.

Jan 1, 1978

By V. Baboudjian, R. J. Geren, J. Thiriar

"The electrolytic tankhouse at CCR was recognized by management as lagging behind modem refineries in terms of productivity, energy efficiency and controls. The operation was also burdened by high maintenance costs of cells, floors and electrolyte recirculation systems.A bench marking program was started in 1986 to evaluate processes and other technology by visiting major copper refineries in North America, Europe and Japan. The basic principles necessary to optimize the operation were defined, and a program calledCCR 2000 was prepared for approval of the necessary capital investments.This paper describes the results obtained to date and outlines the remaining work to complete the modernization program, in particular, the control of electrolytes, the elimination of the Baltimore groove and studies to modernize the stripping operation or adopt permanent cathode technology.IntroductionThe CCR Refinery of Noranda Copper Smelting and Refining (Noranda Minerals Inc.) , in Montreal East, is one of the world 's largest custom copper and precious metal refineries with a capacity to refine 350000 tonnes of copper per year. The silver refinery, which treats the copper tankhouse anode slime, foreign slime and precious metal ingots, produces 800 000 kg of silver, 26 000 kg of gold and 3800 kg of platinum-palladium concentrate annually. Copper anodes are received from the Horne Smelter at Rouyn-Noranda, Quebec, and Mines Gaspe Division in Murdochville, Quebec. CCR also refines anodes from Hudson Bay Mining and Smelting Co. Ltd. in FIin Flon, Manitoba, and remelts anode scrap along with blister and purchased copper scrap ."

Jan 1, 1993

By A. Kapoor, L. Morin, S. Mortazavi, P. Béedard, Gould. W. D., A. Kuiper

The degradation of thiocyanate in a simulated gold mill effluent was studied using a laboratory scale rotating biological contactor (RBC). Complete SCN- removal was obtained at temperatures of 8 and 12°C, and a hydraulic retention time of approximately 3.3 h. The NH4+ produced by thiocyanate hydrolysis was oxidized by nitrifying bacteria to NO2 and NO3-. The HS- produced by thiocyanate hydrolysis was chemically and biologically oxidized to elemental S, which was subsequently biologically oxidized to sulfate. Incomplete sulfur oxidation occurred in the RBC, particularly at 8°C and elemental sulfur deposition was observed on the RBC disks. The RBC feed exhibited toxicity to rainbow trout but the RBC was effective in removing the acute toxicity of thiocyanate.

Jan 1, 2005

By S. J. Laskowski

In potash ore flotation, carried out in NaCI-KCI saturated brine (about 6-7 molar KC1 and NaCI solution), long-chain primary amines are used as flotation collectors. Long-chain primary amines are poorly soluble in water and their solubility further decreases at high electrolyte concentration. For ionic surfactants there is a characteristic temperature (Krafft Point, KP) below which their solubility is too low for micellization. In a previous study, the effect of pH on the KP of dodecylammonium chloride in water was determined [Q. Dai and J.S. Laskowski, Langmuir, 7, 1361-1365 (1991)]. This paper deals with the effect of electrolyte concentration on the KP of dodecylammonium chloride. The derived theoretical relationship between the KP and the critical micelle concentration (CMC) for dodecylamine can be used to calculate the KP for electrolyte concentrations of up to 0.5 mol/L (about 8% NaCI-KCI brine). A simple experimental procedure for the determination of the KP for higher electrolyte concentrations is also described. The results show that the Krafft point of dodecylamine increases from about 17-18°C (in distilled water) to about 80°C at 16% brine saturation.

Jan 1, 2006

By M. S. Badollet

"DURING the past five years, production of asbestos fibers has increased in all countries that list asbestos as one of their mineral resources. Despite the many small mines that have been opened in Canada, United States, Mexico, South America, Italy, South Africa, Australia, Yugoslavia, and Rhodesia, the supply still does not meet the demand. It is estimated that total 1952 world production of asbestos fibers of all varieties approximated 1,600,000 tons, with Canada supplying 966,382 tons (I), or 60 per cent of all fiber mined.Asbestos fiber brokers continually are offering odd-lot samples of chrysotile, amosite, crocidolite, tremolite, and anthophyllite fibers to manufacturers, •quoting fantastic prices for tonnages •varying from just a few to 50 or more in a month. In many cases, the samples are not properly graded and contain quantities of rock impurities and finely ground dust.When vendors submit samples of asbestos fibers, the manufacturer should consider• them in terms of price, quality, quantity, and as possible substitutes for fibers currently used in his products.Grading of these odd-lot fibers in most cases has been poorly done, with resultant non-uniform fiber lengths. In some instances, a number of miscellaneous lots of fibers have been .blended for sale. This blending produces a fiber that is difficult for the manufacturer to accept as a substitute for the well-standardized Canadian fibers."

Jan 1, 1953

By Beatrice Pierre, Juan Carrasco

Altonorte began as a concentrate roasting operation in 1988 under the name of Refimet. In 1993, a copper smelter was built with a design capacity of 203,000 tonnes per annum of concentrate. Since 2001, many technological advances have been made in Altonorte, where the biggest Noranda Reactor in the world is installed being the first Noranda Reactor reaching above one million tonnes of copper concentrates processed per annum. In 2013, Altonorte was acquired by Glencore. Recently due to various new environmental regulations in Chile, Altonorte has evolved to new standards of operation in order to reach the vision of becoming a World Class Smelter. This paper describes the path followed to improve safety, environmental performance, process capacity, reliability, and productivity. The foundation for the growth and success in Altonorte is our People. Employee engagement and branding of our cultural journey is what allows Altonorte to face the future with the certainty of becoming a World Class Smelter. INTRODUCTION Altonorte is located in Antofagasta, the mining capital in the north of Chile and is the last smelter built in Chile practically completed with second hand equipment. The biggest technological change in Altonorte occurred during the phase 3 expansion in 2003, where the old Reverberatory furnace was shut down and replaced by the biggest Noranda Reactor installed in the world. The vessel measures 5.3 m × 26m. ºAdditionally, this project contemplated a new rotary dryer, three (3) new Peirce Smith converters, new anode furnaces and a new Acid plant. The nominal capacity was to treat 816.000 tons of new concentrate per year. In 2008, a new expansion phase was implemented where a new double absorption acid plant replaced the oldest acid plant. Bottlenecks such as blowing capacity and oxygen availability were solved installing a new air blower and a new contract was negotiated with our oxygen supplier to increase oxygen availability up to 683 tpd. This improvement defined the current nominal capacity of 1.100.000 ton of new concentrate per year. Current process description All concentrates are received by trucks directly from domestic mines or from the Antofagasta international port in cases of imported concentrates; the concentrate warehouse has a capacity of 25 kt where the blend is prepared to feed the smelter.

Jan 1, 2019

By Scott A. Trebilcock

Nautilus Minerals Inc the world?s leader in exploration and development of deep ocean mineral resources is today focused on the recovery of high grade copper-gold from in seafloor massive sulphide mineralization. These mineralized belts, analogous to land based volcanogenic massive sulphides (VMS) deposits are located near tectonic plate boundaries of the Western Pacific and around the world. Nautilus; first development project is Solwara 1 located in benign waters in Papua New Guinea. Since 2006 the company has completed detailed environmental and geological studies at Solwara 1, culminating in a number of world firsts, including the first Environmental Permit for a deep ocean mineral project and the first NI 43-101 compliant seafloor massive sulphide resource statement. Nautilus has relied heavily on proven deepwater technologies from the oil and gas industry in the design of the first mineral extraction system. Pipeline trenching units, workclass ROVs, deepwater production risers and drill cutting removal systems will all be adapted at Solwara 1. Key contractors to the project have all been selected for their deepwater experience, creativity and determination to launch this new industry. Innovation is at the forefront of Nautilus? success to date. This paper gives an overview of the Solwara 1 development and describes the exploration and production technologies adapted for seafloor mineral extraction.

May 1, 2010

By P. A. Riveros

This paper describes the leaching of the common copper minerals tennantite (Cu12As4S13), tetrahedrite (Cu12Sb4S13) and enargite (Cu3AsS4) in acidic media using Fe(SO4)1.5, FeC13 or 02 as oxidizing agents. At temperatures <100°C, tennantite dissolves slowly in Fe(SO4)1.5-H2SO4 media, and the rate is directly proportional to the area of the sized tennantite. The rate increases sharply with increasing temperature and the apparent activation energy is 69 kJ/mol. Increasing Fe(SO4)1.5 concentrations slightly increase the tennantite leaching rate. The kinetics of dissolution of disks of synthetic iron-bearing tetrahedrite in Fe(SO4)1.5-H2SO4 media are linear; the leaching rates are slow but increase significantly with increasing temperature, with an apparent activation energy of 120 kJ/mol. The dissolution of sized particles of natural Ag-bearing tetrahedrite in FeC13- HC1 solutions proceeds according to the shrinking core model, and both Cu and Ag dissolve at about the same rate, provided that the total chloride concentration of the solution is sufficiently high to solubilize the AgC1 reaction product. The leaching rates are slow, and the apparent activation energy is 116 kJ/mol. The addition of sulphate ions to the FeC13-HC1 system reduces the tetrahedrite leaching rate to values similar to those realized in the Fe(SO4)1.5-H2SO4 system. At <100°C, enargite dissolves slowly in either Fe(SO4)1.5 or FeC13 media, and the dissolution rate obeys the shrinking core model. The rate increases with increasing temperature and the apparent activation energies are 50-64 kJ/mol. The rate increases slightly with increasing FeC13 concentrations in 0.3 M HC1 media. The leaching of enargite at elevated temperatures and pressures was also investigated. Potentially useful leaching rates are achieved above 170°C, at which temperature sulphate, rather than sulphur, is produced. Lower temperatures (130-160°C) lead to fast initial leaching rates, but the dissolution of the enargite is incomplete because of the coating of the enargite particles by elemental sulphur.

Jan 1, 2007

By S. Shrestha

Magnesium-based alloys are of growing interest for many industrial applications due to their favourable strength-to-weight ratio and excellent castability. Mass reduction has advantages in many industrial sectors for example, in automotive, a reduction in mass improves fuel economy and can lead to more efficient mechanical systems by reducing the weight of moving parts like wheels, gears, pistons. However, the relatively poor corrosion and wear resistance limits the use of magnesium and its alloys in many potential applications. The patented Keronite® plasma electrolytic oxidation (PEO) process enables manufacturers to overcome such problems and, in its latest generation equipment has been developed to industrial realisation for high volume production. This paper presents microstructural characteristics and corrosion performance of two most widely used high pressure die-cast magnesium alloys AZ91D and AM6OB with a duplex corrosion protection coating system that comprised a thin Keronite pre-treatment followed by a subsequent automotive grade final powder coat.

Jan 1, 2006

By Leon J. Perrier

The paper describes the equipment in use, haulage grades, road conditions, tire sizes, tire performance and related problems. Various types of failures and causes, corrective action taken, tire records and reporting for control are also discussed.

Jan 1, 1977

By H. Lazreg

This paper presents an evaluation of surface resistivity techniques as a tool for delineating salt-water intrusion in Shippegan, N.B. The study consisted of resistivity profiling, resistivity soundings and a limited number of induced polarization soundings in selected areas in the Province of New Brunwick. The results from resistivity profiling indicate that when seawater intrusion occurs in a sandstone formation the resistivity contrast is sufficiently large to allow a precise delineation of the intrusion. A formula is then derived to convert resistivity values to chloride concentration in the "cone of intrusion". The results from resistivity soundings showed that shaly formations may have resistivities as low as seawater-contaminated sandstone. An indeterminacy has resulted from this resistivity overlap. A limited number of IP soundings were performed in an effort to resolve it. The results showed that IP can be of appreciable help in resistivity interpretation.

Jan 1, 1972

By M. G. Mena, M. S. Mena-Junio

Silver (Ag) filler is the most attractive choice among all the conductive fillers of die attach materials for the attachment of silicon devices because of its balanced properties and relatively low cost. However, a major problem of silver is that it electrochemically migrates in the presence of moisture and applied bias. In microelectronic devices, silver migration can occur between adjacent conductors/electrodes, which leads to the formation of dendrites and eventually results in short-circuit failure. In order to assess the reliability of these conductive fillers, an investigation for two types of Agfilled die attach materials was done using the water drop test at room temperature and using a 1000 hour temperature-humidity-bias (THB) test under 85 ºC and 85% RH conditions. Four different bias/voltages and six different electrode distance spacing were used. Both dendrite and cloud/lace-like growths were observed as a result of the electrochemical migration of silver, Water drop test results revealed that increasing the applied bias/voltage and decreasing electrode spacing causes migration to occur faster, thus resulting into shorter time to fail (TTF). It was also observed that the growth rate of the dendrites from the cathode increased linearly as the dendrite approached the anode, probably due to a combination of increased ion availability and electric field. A minimum applied bias of 3 volts was required for migration to occur in Epoxy A as compared to 2 volts for Epoxy C. The higher migration voltage requirement for Epoxy A was attributed to the higher volume resistivity of the said epoxy. In addition to the minimum voltage requirement, it was observed that a minimum electric field of about 1 volt/mm is required for migration to occur. The 1000 hour THB testing did not result into any failures. It is surmised that the presence of condensed moisture is another requirement for migration. Such condition is not present during the THB testing.

Jan 1, 2012

By Tom Gaines, G. S. Brant, J. G. Debanne

"AbstractThe Bonnie Glen oil field, one of Canada's largest, lies about fifty miles southwest of Edmonton, Alberta. One hundred and thirty-eight wells have been completed in this field since its discovery in January, 1952. Five different procedures have been used in completing the producing wells.The reservoir is an Upper Devonian biohermal reef with good porosity and uniformly high permeability. The top of the reef is quite flat but the flanks slope at angles approaching 20 degrees from the horizontal. The reservoir has a gas cap with a maximum thickness of 400 feet, an oil column of 300 feet, and a :porcus aquifer of over 300 feet. The reservoir pressure is now 2,400 pounds per square inch gauge at datum ( -4100 M.S.L.).Because of the high permeability and the high •pressure, lost circulation and resultant blowouts are a particular hazard in drilling at Bonnie :Glen field. To reduce the dangers of blowouts, it is general practice to run casing to the top of the reef. If the reef is encountered 'high' it was usual practice to run a liner and perforate for completion. Wells penetrating the •reef below the gas/oil interface were either completed in open hole or through casing perforated opposite the oil pay, with the former method more frequently used. Eight wells were completed by the Humble-Otis permanent-type completion, and recently five high wells were completed open hole with the gas •cap exposed. This latter completion, 'tubing submergence', has proved highly satisfactory thus far.The open-hole type of completion is cheaper than the liner perforation method and results in better well performance. More experimentation and data are needed before the tubing submergence method can be recommended unqualifiedly. but all evidence thus far favours its use in reef reservoirs."

Jan 1, 1955

By G. Hamel

The LCL&L process (Low Caustic Leaching & Liming) is a patented hydrometallurgical route developed by Rio Tinto Alcan (RTA) to economically process spent pot lining (SPL) generated by aluminum cells. The three resulting end-products (carbonaceous, fluorinated and caustic liquor) are inert and have valorization possibilities. An industrial size pilot plant located in Saguenay (Quebec) was inaugurated in mid-2008 to demonstrate and optimize the technology. This paper describes characteristics of the LCL&L process and the experience acquired by RTA since the plant&apos;s start-up, including ramp-up capacity and technology challenges that were overcome. Possible end-products valorization methods are also presented. The carbonaceous end-product can be separated into carbon and brick rich fractions and used as either alternative fuel, reducing agents, or as raw material for third party processes. The development of a conversion process for the fluorinated end-product would allow its reuse as a substitute to fluorspar mineral for aluminum fluoride production. Finally concentrated caustic liquor is already valorized at the nearby RTA Vaudreuil alumina refinery.

Jan 1, 2011

By Jarrett. K. M.

Nobody has, as yet, made a perfect machine. Therefore, when a machine is operating and functioning as it is designed to do, there is always some vibration present. This is easily and simply measurable with present-day equipment and any increase in the amount of vibration will indicate a potential failure. When an increase is noted, vibration analysis can pinpoint the cause of the potential failure and remedial action can be taken before an unscheduled shutdown is necessary or a breakdown occurs.

Jan 1, 1972