Search Documents

By C. A. Pickles

Microwaves are being applied industrially in a number of fields and possess a number of potential advantages that could be applied in extractive metallurgy. Microwave heating has a number of unique characteristics, which distinguish it from the conventional heating methods. In microwave heating, the absorption of energy occurs at the molecular or atomic level and therefore the heat is generated within the material itself. In conventional heating, the exterior temperature is usually higher than the interior, but with microwave heating, the temperature gradient is inverted and thus the interior temperature can be much higher than that of the surface. The energy densities in microwave systems can be relatively high and this in combination with the low thermal conductivities of oxide ores, can lead to very high internal heating rates. In this research, the application of microwave energy for the reduction of a nickeliferous silicate laterite ore has been investigated. The real and imaginary permittivities are the two fundamental properties which determine the microwave absorption characteristics of a material and these were measured for the ore, both with and without carbon additions using the cavity perturbation technique. The microwave heating and reduction experiments were performed in a 0 to 2 kW CTC microwave system. The effects of power input, processing time, sample mass and charcoal additions on the microwave absorption were investigated. Then reduction experiments were performed and the nickel grade of the magnetic concentrate and the nickel recovery in the concentrate were determined.

Jan 1, 2005

By Namavari. H., M. Ashouri, M. R. Sarhadi, S. H. Mansouri, A. Sarrafi

The splash phenomenon and its effective parameters in metallurgical converters have been studied thoroughly for decades. The detailed studies of processes such as tuyere blockage, wave formation during air injection, entrapped phases, and also processes which control the formation of bubbles in viscous fluids are not feasible yet. In this research, we have used a converter-shaped vessel made of flexi-glass. Water and oil have been used as matte and slag phases respectively. The effective operational factors responsible for creation of splashing have been studied such as air flow rate, tuyere angles, depth of tuyere submergence, tuyere blockage, density and viscosity of liquids, liquids heights, etc. The results have been found as follows: the amount of splashing increases slowly as air flow rate increases. However, as the air flow rate reaches a critical value (depending on the physical specification of converter) the amount of splashing rises sharply, because the flow of air inside the liquid changes from bubbling into a jet stream; and most of the splashed materials are in the form of filaments instead of droplets. Changing tuyere angle from horizontal towards vertical position will increase the turbulence level on the fluid surface and causes an increase in the amount of splashing. The effect of tuyere submergence is related to the converter opening angle. As the converter opening angle is shifted towards the hood position, the amount of tuyere submergence and splashing will increase. As density of the liquid increases, the number of droplets splashing increases with a decrease in drop size. Therefore, the total amount of splashing decreases. However, as viscosity of the liquid increases, the splashing material increases due to the changes in the splashed material from droplet shape into filament form. The height of liquid inside the converter, depending on the relative height of heavy phase and light phase, is an important parameter regarding splashing. As the relative height of heavy phase to light phase increases the splashing will decrease. The tuyere blockage will cause the pressure in the inlet manifold to increase; and in real cases will increase the splashing. Finally, we have development a model based on dimensional analysis to relate the above parameters in order to calculate the amount of splashed material.

Jan 1, 2007

By L O. Montpetit

The economics of the asbestos mining industry of Canada, and the physical and chemical characteristics of asbestos fibre, as well as exploration, mining, milling and quality control methods, have been described by several authors in the past few years. The scope of this presentation is to survey the application of asbestos fibres in the major product groups of the construction industry in North America. Principal categories considered include flooring materials, asbestos-cement pipes and building products, high-temperature insulation, textiles, saturated asbestos felts and asphalt com pounds. During 1962, the asbestos mining industry of Canada produced an estimated 1.3 million tons of chrysotile fibre grades, and production capacity is expanding. The market demand for chrysotile fibre, on this continent, has been in the order of 50 per cent of the production volume. The asbestos industry is dependent for growth on the construction industry. Product research is active in finding new uses for asbestos fibre; some of the new developments are presented, including the use of short-fibre asbestos grades for extending the life of asphalt pavement.

Jan 1, 1963

By K. Delbeke

Within the framework of the EU Existing Substance (93/793/EEC) and REACH regulations EC/1907/2006), the copper industry initiated in 2000 a comprehensive Voluntary Risk Assessment of copper and several copper compounds. The Italian Government's Istituto Superiore di Sanità, reviewed the process and reports on behalf of the European Commission. Copper exposure levels to man and the environment from production of copper anodes and cathodes, copper powders and copper chemicals as well as fabrication and use of semi-fabrication products and down stream user products were collected across Europe. Environmental and human health effects data were obtained from literature as well as novel research programs and used to deduct safe threshold

Jan 1, 2007

By N. H. J. Freire, D. Majuste

In this paper, the effects of some organic compounds on the current efficiency, cell voltage and specific energy consumption during nickel electrowinning, and on the deposit features (morphology, crystallographic orientation and nanohardness) were described. The organics tested here (extractant, diluent, flocculant, lubricating oil and acid mist suppressant) are currently used in industrial plants. The results indicated that only the flocculant and acid mist suppressant exhibit relevant negative impacts on the current efficiency and energy consumption. The current efficiency dropped from 93.6 % (organic-free solutions) to 86.0 % and to 92.8% in electrolytes containing 100 mg.L-1 of acid mist suppressant and flocculant, respectively. At this concentration, their addition to the electrolyte led to increases of the specific energy consumption in the order of 18 % (acid mist supressant) and 2 % (flocculant). Cyclic voltammetry showed that Ni nucleation occurs at more negative potentials at 50 and 100 mg.L-1 of these organics in the electrolyte, thus indicating an inhibition of the deposition process. The deposit quality decreased at the higher concentration of all organics, when more hydrogen pitting was observed. The acid mist suppressant caused delamination of the Ni deposit at 50 and 100 mg.L-1. The addition of 100 mg.L-1 of flocculant and acid mist suppressant to the electrolyte increased the nanohardness of the deposit around 31 and 72%, respectively. The increase in Ni deposit hardness may lead to a decrease in the material ductility, thereby affecting the stripping and cutting of Ni sheets. Our findings may be helpful since strong adverse effect of some organics that may be present in the electrolyte were identified, thus the industry can control and optimize the organic´s dosage in the corresponding operations.

Jan 1, 2016

By John C. Wilmot, Robert E. Brewer, Royce J. Smith

In March 2003, Phelps Dodge started up an innovative pressure leach facility for processing copper concentrates at the Bagdad mine in Arizona. This paper describes the development of the concentrate leaching plant at Bagdad and the operational results from start up to present. Optimization efforts and an approach to mineralogical modeling of the concentrate to calculate oxygen utilization are also presented.

Jan 1, 2004

In 2009 Newmont Mining Corporation?s annual global spend on grinding media reached $94M USD, having doubled in the five years since 2004. The major contributing factor to the spend escalation during this period was unit consumable price, with total media consumption also rising as a function of annual ore tonnes milled. In an effort to better understand and manage the growth of this expenditure a significant supply chain management program was implemented. This was complemented by a series of technical initiatives focussed on grinding media specifications, quality management and the prediction of grinding media wear rate as a function of physical ore characteristics. This paper discusses the methodology and outcomes of these activities.

Jan 1, 2012

By A. Danaei, A. McLean, M. Barati, C. Ravindran

"The aluminum industry generates about 90 million tonnes of red mud each year. Previous research shows it could be utilized as a refining flux with a high capacity to absorb phosphorus and sulphur from hot metal in the steel industry. The present study was undertaken to evaluate the melting properties of such fluxes, as it affects the effectiveness of the flux. The results show that the melting behavior of red mud is strongly affected by lime addition and the characteristic melting/softening temperatures reach minimum VALUES (at 32.7 wt% CaO. From these findings, a correlation was established between melting behavior and optical basicity. This allows one to adjust the composition of the flux based on the process requirements. INTRODUCTIONThe aluminum industry generates about 90 million tonnes of bauxite residues each year. This residue is usually red in color because it contains a substantial amount of iron oxide. The red mud, as it is called, is a solid waste with a high concentration of sodium oxide, high pH (10 to 13), and high alkalinity, and thus is harmful to many forms of life. Traditionally, the material is stored in large tailings ponds within the plant’s vicinity (Power, Grafe, & Klauber, 2009). Development of solutions for safe disposal or preferably using this residue for other industrial processes or applications could help restore polluted locations and eliminate a negative impact on the environment (Haake, 1988; Power et al., 2009; Yan & Xuegong, 2010).The mineralogy and chemical composition of red mud depends on the quality of the bauxite and refining process parameters. In general, it consists of iron oxide (Fe2O3), aluminum oxide (Al2O3), titanium oxide (TiO2), sodium oxide (Na2O), silicon oxide (SiO2), and calcium oxide (CaO) (Power et al., 2009). Like most ores and soils, bauxite can contain trace quantities of metals such as arsenic, beryllium, cadmium, chromium, lead, manganese, mercury, nickel, and naturally-occurring radioactive materials, such as thorium and uranium. Most of these trace elements stay in the residue (Power et al., 2009)."

Jan 1, 2012

By R. M. Graves, C. B. McKenzie, D. Barbour, D. W. Desnoyers

"Abstract -The prospective Tulks volcanic belt hosts five significant massive sulfide deposits, Tulks Prospect, Tulks East, Jack's Pond, Daniel's Pond and Victoria Mine, as well as numerous showings and indications throughout its 70 km outcrop length. Regionally, the 498 Ma sequence consists dominantly of felsic pyroclastic rocks and flows with interbedded mafic volcanic units and fine­ grained sediments, commonly graphitic. Contemporaneous granitoid rocks occur in the south half of the belt. Rocks usually display a strong NE-SW, steeply dipping, penetrative foliation and other shear-related high-strain fabrics. Facing directions are normally northwest, although there is local evidence of folding. Sulfide bodies and their alteration systems are deformed and shape-modified in the style of ambient strain.The Tulks, Tulks East and Jack's Pond prospects appear to occupy a similar stratigraphic level, on or near the contact between a thick felsic pile and an overlying broad, conductive package of graphitic sedimentary rocks. AU are pyritic deposits with well-developed footwall alteration systems. The Tulks prospect comprises four polymetallic lenses totalling 750 000 t. Three lenses constituting more than 6 000 000 t of sulfide mineralization are indicated at Tulks East but only the 210 000 t ""B"" lens contains significant base metals. Jack's Pond consists of a very extensive, zoned alteration complex in which four lenses of massive to semi-rnassive pyrite + chalcopyrite are known.The central part of the system, characterized by Mg chlorite and carbonate, is enveloped by pervasive sericitization and capped by intensely silicified and pyritized volcanics. The sulfide lenses are interpreted as part of the footwall zone and are beneath that part of the system most likely to host polymetallic massive sulfides.Daniel's Pond differs from the other prospects in such fundamental ways as metal content, associated alteration and structural setting. The deposit comprises strongly tectonized, Ag-rich, Zn-Pb mineralization distinguished by a pronounced Ba-As-Sb signature. Mineralization is confined to a narrow, north-south high-strain zone which separates unstrained mafic volcanic rocks to the east from well-foliated felsic rocks. The deposit Jacks an extensive alteration halo and at its north end is associated with a lens of barren, undeformed massive pyrite.The Victoria Mine deposit, the most cupriferous of the five, is related to a moderately dipping structure that separates well-foliated Tulks volcanic rocks from an overlying, Jess deformed volcanic­ sedimentary sequence that may be as young as 462 Ma. The structure is also the locus of black chlorite, dolomite and quartz alteration. Structurally remobilized precursor sulfide mineralization is one possible source for the deposit."

Jan 1, 1993

By E. Viljamaa

In this research, earlier developed information integration method and novel web technologies are applied to intensify infrastructure construction process control. The applied method uses semantic methods to integrate scattered information that is later on exploited by process management using state-of-the-art web technologies. The applied method and web technologies not only improve the process management situation awareness by integrated up-todate multi-source process data but also provide platform independent access and visualization tool for process data. Utilization of such technologies potentially lead on cost savings, make processes safer and also more environmentally friendly. The integration method also enables intelligent queries to the integrated data making possible to use machine based inferring to the data.

Aug 1, 2013

By C. H. van Eendenburg

"Installation of a 3.6 km long raw coal conveyor in the Balmer open pit was undertaken to improve over-all haulage efficiency. This paper covers the rationale behind this project, system design and construction aspects and initial operating experiences. The majority of the construction work was performed by our own personnel. Where feasible, used equipment was installed to reduce capital cost and facilitate a tight construction schedule.BackgroundWestar Mining Ltd's Balmer Mine is located in the British Columbia Rockies, just outside of the town of Sparwood in the southeastern corner of British Columbia. The open pit mine, which has been in operation since 1969, currently produces about 6 million clean tonnes of coal per year, mostly for the metallurgical coal export market. Run-of-mine coal tonnages total between 9 and 9.5 million annually and waste removal volumes exceed 30 million bank cubic metres.The mine is a truck/shovel operation; loading equipment includes nine electric shovels, five front-end loaders and a hydraulic backhoe. The truck fleet consists of 40 units of 154-tonne, 181-tonne and 315-tonne capacity. The newer 154-tonne trucks are used for coal haulage for which they have been equipped , with tailgates to maximize their coal carrying capacity."

Jan 1, 1990

By James W. Cameron

DESPITE the fact that, after oxygen and silicon, aluminum is the most abundant and widely distributed element in the earth's crust, it is, commercially, a modern metal. Attempts were made by Sir Humphrey Davy and other chemists to decompose alumina, the oxide, into its elements, but with unsatisfactory results, and it was not until 1827 that Wohler succeeded for the first time in isolating the metal in pure form. Some thirty years later, commercial production of aluminum was started in a plant near Alais, France, using a process developed by Deville which was a modification of that of Wohler. It was not, however, until around 1886 that possibilities of low-cost production were realized. Hall and Heroult discovered, independently, the now famous process for extraction of aluminum by the electrolysis of alumina (Al,O,) dissolved in fused cryolite. This discovery, with its subsequent effect in reducing the price of the metal, was perhaps the greatest single factor contributing to the remarkable growth of the aluminum industry. But only in the years following the Great War did aluminum begin to attain equal importance in many fields with other non-ferrous metals. Numerous factors, political and economic, in the past decade have had a profound effect on the industrial history of the metal. At present, systematic substitution of aluminum for other base-metals is proceeding at a rapid rate in such countries as Germany and Italy with a view towards 'economic self-sufficiency'. Quite naturally, ?the economic depression started extensive research and experiment in various industries in an attempt to improve efficiencies and lower costs. Partial answers have been found in the extended use of aluminum and its alloys. Even against the background of tremendous technological advance that has marked the past fifty years, the rise of the aluminum industry must necessarily stand out conspicuously.

Jan 1, 1939

By C. George Miller

"As the influence of governments has become more widely felt, the use of research techniques to analyze policy has increased. Mineral economics, as one of the foundations of mineral policy research, has grown accordingly. Policy research and analysis has been carried out within governments, university departments and the private sector. Each of these institutional environments has characteristics which influence the topics of study, the approach, the methodology and the output of the research. A brief survey of recent research activities provides illustrations of trends and developments occurring within this organizational framework.A radically different organization, the independent research institute, has begun to make an impact on policy research in recent years, and will have an increasing importance in the future. Combining certain features of the traditional research organizations, it nevertheless has important differences which are essential to its effective functioning. An overview of the formation, goals, organization and operation of one such institute is presented."

Jan 1, 1976

By D. S. Salonine

Aluminum alloys offer a wide range of capability with a unique combination of advantages that makes them the materials of choice for numerous products and markets. One of the most important applications is their use as the primary structure and outer envelope in aerospace vehicles. Wide and thorough studies on hot working and microstructure evolution of aluminum alloys have been made in Russia. The most important appear to be: - introducing the structure diagrams in strain rate - temperature coordinates which show areas of different microstructures (non-recrystallized, recrystallized, and mixed) after the hot deformation and the following heat-treatment for common aluminum alloys (Yu.M. Vainblat); - studying the press-effect ("structural effect" by V.I. Dobatkin); - learning the influence of hot worked substructure on aging mechanisms; conducting researches on press heat-treatment. These works allowed a deeper understanding and a better control of the mechanical behavior of aluminum products. Comparisons are made to equivalent developments in Europe and America.

Jan 1, 2004

By R. A. Crouse

The Tanco pegmatite at Bernie Lake, in the Lac du Bonnet mining district of southeastern Manitoba, is a unique deposit of Li, Rb, Cs and Ta, with substantial reserves of Be and several industrial minerals. This paper summarizes the present state of understanding the regional geology, structural setting, zoning, mineralogy and geochemistry of the pegmatite, and the mining and ore-processing methods used in its exploitation.

Jan 1, 1979

By Maurice Lauzon

"Aerial surveys of the open pits have been conducted regularly at Lake Asbestos of Quebec, Ltd. -a subsidiary of American Smelting and Re-fining Company -since 1958. Ground controls are supplied by Lake Asbestos, and a topographic map of the pits at a scale of 1 in. to 50 ft., with 2-foot contour intervals, is obtained by aerial photography. The information from the topographic map is then transferred by the Lake Asbestos engineering staff to sections from which the volumes removed are calculated. Considering the size and complexity of the operation, this system has proved to be the cheapest, fastest and most accurate way of determining the quantities of rock and overburden removed. More than 11,000,000 tons of ore and waste are mined each year in three different pits. Further-more, the nature, shape and extent of the orebodies make it necessary to mine on many (up to eight) benches of a pit during a single year. In addition, there are sections of the pits where it is impossible or un-safe to survey the crest of some benches by standard ground methods. For these reasons, the tonnages obtained by truck count are checked and adjusted by aerial survey. These surveys are now taking place every six months. With this system, it is possible for a two-man surveying crew to look after all field work in the mine area."

Jan 1, 1967

By D. R. Pyke, R. S. Middleton

"Three main types of base metal sulphide mineralization are present in the Timmins area:(1) -Massive and stringer-type copper-zinc deposits occurring mainly in pyroclastic rocks, as typified by the mines of Kam-Kotia, Jameland and Canadian Jamieson, or within or close to possible breccia pipes as shown by the Genex and Kidd Creek mines. With the exception of the Kidd Creek mine, all of these orebodies occur northwest of Timmins (Kamiskotia area) and appear to lie within or close to a major center of volcanic activity characterized by a thick accumulation of felsic pyroclastic rocks and subordinate epizonal intrusions. The margins of the rhyolitic pile are interfingered with mafic volcanics; overlying sedi-ments mark the termination of a vol-canic cycle. The copper-zinc deposits in the Kamiskotia area are confined to a particular stratigraphic unit. Ore-bearing solutions were probably derived from the intrusive complex of the volcanic pile.(2) -Porphyry copper deposit of the Mcintyre mine. The deposit occurs in a quarz porphyry intrusion related to the volcanism in the area (Hurst, 1936). Mineralization was probably introduced at the time of intrusion, and subsequently redistributed within the porphyry during deformation. (3) -Massive and disseminated nickel mineralization, associated with serpentinized alpine-type ultramafic intrusions, as shown by the Alexo, McWatters, Hart, Inco and Texmont deposits. The nickel mineralization occurs at or near contacts of the serpentinites with felsic or mafic volcanics, or sulphide-bearing iron formations. The nickel deposits south of Timmins are confined to a particular stratigraphic unit along the margins of domical-shaped structures which appear to outline former volcanic centers. Sulphurization as pro-posed by Naldrett (1966) appears to be a workable hypothesis for the formation of some of the deposits."

Jan 1, 1971

By L. L. Sirois

Because segments of the Canadian mineral-based economy are dependent totally or in part on foreign sources of certain minerals, their well-being may well be affected by inability to obtain these minerals. Where such dependency exists, it is therefore important that contingency plans be available to counteract possible price increases or lack of supplies by means of technology, developed well in advance of any pending crisis . Canada is vulnerable to possible future real or artificial shortages of certain foreign-produced mineral commodities, and science and technology can provide information for the development of policies for counteracting efforts by foreign exporters to control prices or limit supplies.

Jan 1, 1977

By A. J. Naldrett

"Sulphurization of peridotite, that is 'to say reaction between sulphur from an external source and iron and nickel in the silicate minerals of the peridotite or in partially consolidated magma, is believed to be the me-chanism by which the small iron-nickel sulphide deposits associated with the ultrabasic rocks of the Porcupine district have formed.The pyrrhotite-pentlandite ore at the Alexo mine, Dundonald township, is localized by a shear that closely follows the lower contact of a peridotite lens. In the past, to account for this orebody, the magmatic segregation hypothesis has been advanced on the basis of textural evidence and the presence of the sulphides at the base of the lens. The nickel sulphide de-posits of the Porcupine, however, are not characteristically found along the basal contacts of bodies of peridotite. Furthermore, this study has shown that textures formerly thought indicative of magmatic segregation have been formed in certain deposits by the selective replacement of silicates by sulphides.At the Alexo mine, very minor amounts of pentlandite and heazle-woodite (Ni3S2) occur in the peridot-ite hanging wall adjacent to the ore. These sulphides are interpreted as having formed by sulphurization, the sulphur involved coming from the pyrrhotite-pentla.ndite ore emplaced along the shear. This reaction aureole raises the question of the role of sulphurization in the formation of the main mass of the sulphide ore. The very localized equilibrium that has been found to exist between sulphides and silicates in deposits throughout the area, the results of nineteen sulphur isotope determinations, and the abundance of pyrite and pyrrhotite in the volcanic country rocks of the Porcupine indicate that these deposits were formed by sulphurization rather than magmatic segregation."

Jan 1, 1966

By S. A. Luciani

"In 1957, an asbestos orebody was discovered in the northern sector of the Ungava Peninsula of the Province of Quebec, an area now identified as Asbestos Hill. The deposit is situated on a plateau 1700 feet above sea level and 42 miles inland from Hudson Strait. It is a bleak, iso. lated location of typical arctic environment. Fifteen years were to pass before the first shipment of ungraded fibre was made in 1972. These years we1•e occupied with field surveys and investigations, diamond drilling, engineering design, evaluation of investment and operating costs, and construction. The problems normally associated with mine development were further complicated by location, isolation, and the extreme cold and permanently frozen ground of the arctic regions. Unique to an isolated arctic operation are the organization of support facilities and services, procurement and retention of personnel, construction of access roads and airports, and scheduling of product out and supplies in during the short summer period of sea navigation."

Jan 1, 1976