Search Documents

By W. J. Grose

The Embankment Place office development over the platforms of Charing Cross Railway Station in London has presented many interesting and unusual problems to the engineers involved with the project. The main structure is supported on widely-spaced columns which penetrate the station platforms and underlying vaults, calling for high capacity foundations built in severely restricted spaces. Hand-dug underreamed piles were chosen. Whilst a conventional design approach was taken to size the piles, a detailed appraisal of ground movements was made to explore the effects of the new building loads on the existing foundations, not only beyond the site perimeter but also those amongst the new foundations. Before construction of the pile proper could take place, it was necessary to sink a caisson through the upper unstable and water-bearing soils. This being identified as a high-risk item, a full-scale trial was carried out prior to embarking on the main works. The twenty-one hand-dug piles were 2.5m diameter, over 30m deep and belled out to between 4.5m and 6.6m.

Jan 1, 1989

By Yajie Wang

High horizontal stress and its adverse effects on longwall gate entries have been witnessed in many US coal mines for the past years. It can cause cutter roofs and leads to roof falls either in the headgate or tailgate entries depending on the relative orientation of the panel to the maximum principal horizontal stress. Underground observations have shown that if the maximum principal horizontal stress is perpendicular to the panel entries, the roof is in the worst condition and if the maximum principal horizontal stress is parallel to the entries, the entry is in the best condition. However, little has been done about the high horizontal stress effects on panel entries subject to different orientations of high horizontal stress. In order to design a longwall panel and control the roof effectively, the redistribution and concentration of high horizontal stress field must be fully understood. Using 3-D finite element analysis, this paper presents the high horizontal stress redistribution and concentration for a retreat longwall face with different orientations of high horizontal stress. Based on the results, possible roof failures for different orientations of high horizontal stress are analyzed. A panel design criterion is recommended.

Jan 1, 1996

By Siavoljub D. Maksimovic

The Bureau of Mines, through a cooperative agreement with Duquesne Light Co. of Pennsylvania, field tested a method of using pneumatic stowing of crushed limestone to construct seals in long-abandoned mine openings that were part of an active mine closed shortly before sealing. A total of 13 openings at 11 sites were backfilled. In pneumatic stowing, material is conveyed through a pipeline and into the mine opening under low air pressure. The stowing equipment consists of a power sup-ply, a blower, a feeder to inject material into the pipeline, and a nozzle for directing the placement. Material is ejected from the nozzle at high velocity, creating a high-compaction fill upon impact. The fill material used was well-graded limestone aggregate up to 1-1/2 inches in diameter, with sufficient fines. This fill was modified at five locations by the addition of portland cement, expansive cement, and/or bentonite. The pneumatic stowing method is safer and faster than conventional methods, is cost competitive, and eliminates or reduces the exposure of workers to possible hazards since the nozzle can be kept outside the mine opening. The equipment is mobile, but some modifications in the technique would improve performance. The technique was used at remote locations where other methods could not be used without disturbing the environment.

Jan 1, 1982

By R. A. Halatchev

A risk model for assessment of the uncertainty in the forecasts of the planned profit is developed. It is based on the selling price of the metal recovered from the ore and the production per shift of the excavators. These two critical variables characterise the economic and technical aspects of the mining venture. Time-series methodology is used to describe the behaviour of the economic variable, which improves the adequacy of the modelling. A hypothetical open-pit gold mine is used to illustrate the application of the model. Results obtained show that the model is a good alternative to sensitivity analysis in taking account of the stochastic character of the price of the metal recovered from the excavated ore and the production per shift of the excavators used. The model can be extended by the inclusion of new variables that have a probabilistic nature

Dec 1, 1996

By McLeod RL

The Tolukuma gold-silver prospect is located approximately 100km N of Port Moresby in the Central Province of Papua New Guinea (PNG). Epithermal "adularia-sericite" style mineralisation crops out over 1200m within an en echelon quartz veined zone 1 to lOm wide. At a 4g/t cut-off grade, a geological resource of approximately 1.47Mt @ 13.77g/t Au is indicated from 38 diamond drill holes completed since discovery by Newmont Pty Ltd in September 1986. At a regional scale, Tolukuma miner- alisation appears localised in a dilatant zone at the intersection of a 1150 magnetic structure, and the western margin of a N-S trending graben which is filled by a Pliocene volcanic complex contemporaneous with the Mt Davidson Volcanics 30km to the W. A l0km diameter circular Landsat feature, which may reflect magma emplacement at depth, occurs immediately N of Tolukuma and nearby mineralisation. Mineralisation at Tolukuma occurs in sub-vertical quartz veins at, or adjacent to the faulted contact between Pliocene basic and intermediate volcanics/intrusives, and quartz mica schists and phyllites of the Cretaceous Kagi Metamorphics. Most veins display evidence of multiple episodes of brecciation and textures indicative of cyclic boiling, including crustiform rhythmic banding and quartz pseudomorphs after platy calcite.

Jan 1, 1991

By W. A. Heitbrink, J. D. Ashley, R. E. Gresh, J. A. Organiscak, A. B. Cecala

Many different types of mobile equipment used in surface coal mining utilize enclosed cabs to protect equipment operators. The overburden removal process is extremely dusty and can cause excessive exposure to respirable dust, especially crystalline silica. After equipment is used for years, many components of the enclosure deteriorate and its effectiveness is greatly reduced. This report discusses a cooperative research study performed on an Ingersoll Rand DM45E surface drill, retrofitted with a new Sigma pressurization and filtration system. Respirable dust concentrations were substantially reduced from 0.64 mg/m3 during pre-testing to 0.05 mg/m3 during post-testing with the new system, representing a 92% reduction in dust levels in the drill cab. This new system appears to be a very well-built and sturdy device, well-suited for the mining industry.

Jan 1, 2002

By Vinay Kumar Agrawal, Rama Nath Praharaj

IMFA Group is the largest producer of Charge chrome not only in India but also in Asia. This Group has plants situated at Therubali and at Choudwar. They also have a Thermal power plant at Choudwar which not only caters to the power requirement of Choudwar plant but also supplies power to Therubali. The plants are fed for Chromite ore through the captive mines namely Nuasahi Chromite mines (40.47 Ha) , Bangur Chromite mines(37.34Ha), Sukinda chromite mines (116.76 Ha), Mahagiri Chromite Mine(73.777 Ha) and Chingudipal Chromite mines (26.62 Ha). Nuasahi Chromite Mine, which is situated in Keonjhar district, is an underground mine and is based upon best technological advancements in the industry. The underground mining operation is certified under ISO-9002, ISO-14001and OHSAS 18001. This not only shows the concern for the quality, environment but also for the health of the employees. The Nuashahi is the first chromite mine to backfill the opencast excavations created during the last 50 years and carry out the production from underground area below the opencast workings. This paper deals with the state of art technology of sub-level open stopping in thin ore bodies. The under-ground mine openings was started in the year 1997. In next four years the production of chromite from underground was started.(2001). At present the mine is in a good shape with several running stopes. Today it is producing around 10,000 Mt per month of chromite. The development of the mine is carried out with an average of 200 mtr per month of tunneling. The mine is having a mechanical ventilator having a capacity of24000 M3 per hour at 50mm water gauge, thus feeding sufficient air for the persons working in underground. The mine is being dewatered through a most modern positive suction sump, having a capacity of 500 cum and operated with 120 HP pumps. After commissioning of this sump in the year 2003, the mine has taken a quantum jump in production with remarkable saving in power consumption.

Jan 1, 2007

By Madsen I. C, Langberg D. E

Recent advances in X-ray diffraction (XRD) technology have made it possible to conduct powder XRD measurements on samples at high temperatures during reaction. State-of-the-art detectors are now capable of rapidly acquiring diffraction patterns across a wide angular range (typically 120"20) enabling phase transformation rates to be measured directly during sample reaction. In this study, the phase transformations during the reduction of hematite to metallic iron by five per cent hydro ºen in nitrogen gas mixtures, were measured in situ between 500 - 700 C. Complete X-ray diffraction patterns were acquired within 15 seconds every one minute, enabling direct measurement of the transient phase abundances during the reaction. The data were quantitatively analysed by the Rietveld method to yield the abundances of hematite, magnetite, wustite and metallic iron, as functions of time during the reduction process. A first-order reactions-in-series model was proposed, and the reaction rate constants and activation energy were determined from the time-dependent phase abundance data.

Jan 1, 1999

By T. F. Anstett

The Bureau of Mines estimated the potential availability of tungsten from 57 mines and deposits in 19 market economy countries. The tungsten resources of China and the U.S.S.R. were also estimated. This resulted from an evaluation of tonnage-cost relationships indicating the quantity of tungsten available as ammonium paratungstate (APT), artificial and natural scheelite, and ferrotungsten at various average total costs of production including 0- and 15-pct rates of return on invested capital. The evaluated deposits contain 1.2 million metric tons (t) of recoverable WO3, of which approximately 52,000 t of AEYT can be produced at the January 1983 market price of $5.37/lb, 89,000 t of natural and artificial scheelite at a market price of $3.63/lb, and 1,700 t of ferrotungsten at $5.61/lb of tungsten. An annual availability analysis indicates that by the early 1990's new deposit discoveries, development of known prospects, or expansions of producing mines will be necessary to meet projected tungsten demand.

Jan 1, 1985

By Véronique Falmagne

The mining sequence at Noranda?s Bell-Allard mine calls for two mining fronts retreating toward a central pillar known as the Retreat Zone between pyramids A and C. It is clear from numerical modeling and rock mass characterization that the induced stress level in the pillar will exceed the rock mass capacity. A mining plan was developed including the re-dimensioniong of stopes in the Retreat Zone, additional ground support and instrumentation in order to ensure the safety of the workforce and to maximize ore recovery while minimizing production delays. The mining strategy consists in allowing the rock mass to fracture and fail progressively while maintaining control of the existing openings with the appropriate support. A systematic analysis of rockbursting and caving hazards was conducted for all accesses and stopes in order to plan ground support and instrumentation needs.

May 1, 2003

By Pound J. R

THIS mine, which is the property of the S. and M. Syndicate, London, is located at Moina, in North-West Tasmania, 18 miles from Stavertorr railway station and 36 miles from Devonport. There are metalled roads from both of these places, and, althoughhilly, these are good for team or motor traffic. Mails and passengers are provided for by a tri-weekly coach service from Sheffield, a railway town, distant 23 miles. The Moina mining field is situated on a main spur between the Forth and Iris Rivers, andat an elevation ranging from about 500 ft. above sea-level at the Forth River to 2400 ft. at the All Nations mine. The elevation at the mine office of the S. and M. mine is 1900 ft. The average annual rainfall, as recorded for the past eight years, is. 68 in.This inclildes, however, a couple of years during which the rainfall was much above normal, and taken over a longer period 60 in. would be nearer the average.

Jan 1, 1919

By Patrick E. Durnal

A joint venture of Ben C. Gerwick Inc., Sverdrup (now Jacobs) and DMJM (now DMJM Harris) designed the $779 mill seismic upgrade of the Richmond - San Rafael Bridge over the San Pablo Bay in the San Francisco Bay Area and provided construction support to Caltrans. Construction of the marine foundation retrofit was completed by a joint venture of Tudor Saliba/Tidewater/Koch-Skanska and their subcontractors: Pomeroy Precast Construction, AGRA Foundations, Dutra Construction and Vortex Divers. Construction management and inspection was performed by Caltrans with support of various consultants.

Jan 1, 2013

By Steve Kral

MINExpo INTERNATIONL 2000 was a good place for companies to introduce new products, technologies and services to the mining industry. Caterpillar took that a step further. The company hosted a one-day preview of its mining products at its Tinaja Hills Training and Demonstration Center near Tucson, AZ. About 30 members of the trade press spent the day at Tinaja Hills before heading on to Las Vegas for MINExpo INTERNATIONAL 2000. Dozens of Caterpillar professionals provided the editors with a first-hand look at Caterpillar’s mining trucks, loaders, excavators, road graders, water trucks and engines. In addition, these Cat experts explained the intricacies of each piece of equipment, the latest technology that led their improvement and their value to the company’s mining customers.

Jan 1, 2000

By Robert A. Field

Static-Load Piledriving systems utilize hydraulic push to advance piles into the ground. Dynamic systems (ie. hammers and vibratory equipment) utilize impact, or vibration, to advance the piles. Static-Load systems are most commonly utilized in situations where noise or vibration would adversely affect the people, structures or equipment located near the site. Static-Load technology is most advantageous in situations where vibration, noise or access constraints make it difficult, risky or disruptive to utilize conventional piledriving systems.

Jan 1, 1995

By Bernard Jones

LTUG ? A meeting of many mining companies that are using large tires ? Introduction of the mines and size ? Companies go over their usage of tires and performance ? As a group we discuss how the manufactures are doing with supplies and performance (who's running what sizes and manufactures they are using) ? The mine's best practices they use (which ones work for them and which ones don't) ? Where the mines see themselves going in the future ? What type of tire management the mines have in place

May 1, 2009

Theories of ore genesis. have both practical and philosophical application-practical in that they influence our search for new ore bodies; philosophical in that they provide a test for our theories of petrogenesis-and our ingenuity.For example, the theory of granitization requires an explanation of ore genesis compatible with the general concepts of granitization.Our understanding of some processes of ore formation, such as supergene enrichment, or the formation of residual lateritic iron ores, is so complete as to permit of nq controversy.For other ores, like the oolitic iron ores of England and France, and elsewhere, or the segregations of chromite or ilmenite in basic igneous rocks, the broad principles are generally agreed on; dispute is limited to details of process.But for a wide range of ore deposits there is no such agreement. Completely incompatible hypotheses are advanced to explain' identical facts, and we have difficulty in finding new facts or criteria that will distinguish unambiguously between them.In thinking about such ores, a co:n;venient starting point is provided by Schneiderhohn's (1953) fourfold division of ore deposits:1. The secondary hydrothermal ore deposits occurring in Mesozoic-Neozoic cover strata of Europe.2. The "regenerated" younger ore deposits in Alpine type mountain chains.3. Post-Cambrian primary hydrothermal ore deposits.4. Ore deposits of the PreCambrian shields.To these we may add a fifth group:5. Stratigraphically controlled sulphide deposits.

Jan 1, 1956

By H. Maleki

As mining continues toward deeper reserves in thick western US coal fields, the control of mining induced-seismicity has become a priority in many operations in Utah, Colorado, and Wyoming. Gradual floor heave, common in many coal mines, has historically not been a safety issue. However recent occurrences of sudden floor heave accompanied with seismicity in a few deep mines have fueled this investigation. The focus is to identify and study the mechanisms resulting in sudden heaving of the mine floor in western U.S. deep coal mines through analytical calculations and back analyses of an actual event in a cooperative mine. Based on review of available data in three mines, underground observations and back analyses of an actual event, the authors have identified the following contributing factors (1) presence of stiff stratigraphic units and thick seams mined at depths exceeding 1000-ft (2) presence of geological discontinuities reducing the in-situ strength of the coal with calculated factor of safety near 1 for the mine floor (3) mining approaching areas of higher than normal stress gradient associated with previous mining or structural anomalies or surface topographic highs and (4) an additional source of energy triggering sudden failure such as periodic caving or slip along geological discontinuities. Preliminary examination of seismic data for the actual event in the cooperative mine and underground observations excluded fault slip at the mining horizon as the triggering mechanism but highlighted the significance of weak, anisotropic strata conditions near the intersection of two faults.

Jan 1, 2009

By R. P. Jensen

This is a sampling of the papers presented at the conference, the proceedings can be bought from the SAIMM Arbitrary Lagrangian Eulerian (ALE) computational techniques allow treatment of gases, liquids and solids in the same simulation. ALE methods include the ability to treat shock waves in gases, liquids and solids and the interaction of shock waves with each other and with media from one of the other categories. ALE codes can also treat explosive detonation and the expansion of the explosive gases and their interaction with air and solids. ALEGRA is a 3-D ALE code that has been developed at Sandia National Laboratories over the past few years. ALEGRA has been applied to a 2-D simulation of presplitting using decoupled explosives in rock blasting with very interesting results. The detonation of the explosive at the bottom of the hole sends a shock wave up the borehole driven by the explosive gas expanding into air. The explosive gas compresses the air against the stemming column where it rebounds and recompresses at the bottom of the borehole. This type of ringing takes several cycles to damp out. The explosively induced expansion of the borehole is also treated by ALEGRA as well as the shock wave imparted to the rock. The presentation of this paper will include several computer animations to aid in understanding this complex phenomenon.

Jan 1, 2000

By K. Najim, D. Hodouin

"The raw ores which are processed in mineral processing plants exhibit very strong variations of their physical and chemical properties. As a consequence, the performances of the comminution and separation processes vary greatly from time to time. Model-based control strategies improve the performance of the plant; however, they require some form of adaptation to cope with the variations of the are properties.This paper deals with the use of adaptive techniques for the control of mineral processes. It begins with a survey on adaptive control algorithms including parameters estimation aspects. Then several examples dealing with crushing, rod, ball, autogenous and semi-autogenous grinding, flotation , drying and calcination processes are reviewed.IntroductionThe operation of the various processes of mineral processing plants (crushing, grinding, flotation, dewatering, etc.) is generally controlled using empirically tuned regulators of constant structure, such as PID controllers. To improve the operation performance, mineral processors try to implement specifically designed controllers, i.e. controllers based on plant dynamic models. Most of the time, these techniques improve the control of the mineral processing installations. However, modelling is a complex procedure because of the problems of measurement and data management, specific to this industry, and because of the variations of the model parameters. In this context model-based control strategies do not always bring the expected improvements or are sometimes discarded and replaced by more conventional techniques .The sources of variation of the dynamic behaviour of mineral processing systems can be classified into three categories: (I) the inherent changes of the raw ore properties (composition, grindability, mineralogical texture, etc.); (2) the process tuning modifications (grinding media loads, number of hydrocyclones, slurry level in flotation cells, agitation speeds, etc.); (3) the feedrate variation of the ore, water, chemical reagents, etc. All these factors change the fundamental properties of the process dynamics such as the grinding or flotation rates and the residence time in the equipment. The simplified linear models which are used to describe the process dynamics are not able to track the complex behaviour of the mineral processing systems when the amplitude of the sources of variation are too large. The mismatch between the model and the plant behaviour is then frequently a cause of model-based controller failures."

Jan 1, 1992

By D Preedy, J K. Claflin, S R. La Brooy

A gold mine in north-eastern Africa has expanded throughput from 5 to 10 Mt/y in recent years. The original carbon regeneration kiln was incapable of achieving required throughput or meeting process conditions to reactivate the carbon due to heavy fouling by high molecular weight frothers and collectors. A new high temperature kiln was required.The design criteria for the carbon reactivation kiln and associated equipment were revised, then implemented in close cooperation with a kiln vender who had previously supplied kilns operating successfully on highly fouled carbon. The result is a whole facility, holistically designed to achieve the technical criteria.The new carbon reactivation facility has been operating since 1 July 2014. What have we learned? What has performed to expectations? What could be done better?This paper presents lessons learnt regarding the design, implementation, operation and maintenance of the Ausenco Carbon Reactivation Kiln. ‘Lessons’ are associated with threats and opportunities (risks) that have that have been realised. The importance of identifying and managing risks for even small straightforward projects is demonstrated.CITATION:Claflin, J K, La Brooy, S R and Preedy, D, 2015. Lessons learnt and performance – installing and commissioning an Ausenco carbon reactivation kiln in Africa, in Proceedings MetPlant 2015, pp 163–174 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 7, 2015