Search Documents

By William J. McDonough

Advanced materials are polymers, metals, and ceramics fabricated as intermaterial compounds, alloys, or composites. The resultant components have higher strength-to-density ratios, greater hardness and wear resistance, and one or more superior thermal, electrical, or optical properties when compared with traditional materials. Advanced materials, the basis for many of today's emerging technologies, offer savings in total energy consumption, improved performance at reasonable cost, and less dependence on imports of strategic and critical mineral resources.

Jan 1, 1992

By A. Lewis, J. Zachwieja, M. Widell, P. Zhou, W. W. Geissler, M. Svensson, A. Movahedi, H. Nordberg

Flotation collectors for sulfide minerals has been traditionally based on xanthate, thiophosphate, thiophosphinate and thiocarbamate, all derived from sulfur chemistry. Tecflote™ is a new family of patented collectors based on nitrile chemistry which can supplement or replace thiol collectors, depending on the ore types. A steep grade-recovery curve typical of Tecflote™ collectors was observed when using Tecflote™ as the main collector for the rougher and cleaner steps allowing a better recovery compared to current thiol collectors while maintaining the desired grade. Additional recovery increase has also been observed by the addition of scavenger steps using Tecflote™ collector in combination with current thiol-based collector. The selectivity seen in the lab is transferred to full scale trial and is clearly seen in the rough flotation where the increase in the rough concentrate grade of 5% after pumping Tecflote S11 directly into the tank cell. The mechanisms for Tecflote’s selectivity towards sulfides are currently under investigation and will be discussed. Results of TOF-SIMS analysis will be presented, demonstrating the collector’s selective affinity to different mineral surfaces in flotation. INTRODUCTION The history of collectors used today started in 1882 when Zeise first made xanthates. It was first used in flotation in 1925 – Cornelius Keller’s first patent (Fuerstenau, Jameson, Yoon, 2007). Between 1928 and 1930 American Cyanamid filed 7 patents for dithiophosphate, including flotation and chemical synthesis of the reagent, the first of which was filed by Christmann in 1928 (Christmann, 1933). Synthesize of thionocarbamates for mineral flotation was filed in 1954, by Dow Chemical Company (Harris, 1954). Now that the head grades have been declining over the last decades the need to find more selective collectors to extract difficult and complex ores has pushed the industry to look at different chemistries. Thiol collectors standard to the industry rely on the sulfur in the collector molecule to bond to the mineral surface. The electronic property of this group is modified by the adjacent chemical groups, such as additional S, P or N have the effect of changing the selectivity of the collector (Wills & Finch, 2016). In the case of xanthate the length of the hydrophobic group also has an effect on the selectivity with some minerals such that the ethyl xanthate is more selective against pyrite and pyrrhotite than the long chain xanthates (Wills & Finch, 2016).

Jan 1, 2019

By Miklos D. G. Salamon

If all stratifications are horizontal, the computation of surface deformation induced by coal mining involves the prediction of roof and floor convergence and then the transfer of the effects of this relative displacement to the surface through the use of the appropriate influence functions. A laminated model, in the form of a quasi- continuum, provides a simple means of computing the approximate convergence distribution and leads to the Gaussian distribution as the influence function. The ideas presented in this paper represent a subtle but fundamental generalization of the influence function Method. It is postulated that the influence of a small area of extraction is proportional to the roof and floor convergence and not to the thickness extracted. This difference in definition removes many conceptual difficulties associated with the influence function method. To demonstrate the utility of the model, the surface disturbances induced by the extraction of a parallel sided long panel are derived. Formulae giving subsidence, tilt, horizontal displacement and strain are given.

Jan 1, 1989

By T F. Guerin

Explorationn and mining have shown to cause significant impacts to the terrestrial and marine environment. Current mining and exploration techniques are outlined in the light of their potential to impact upon the environment, ie negligibly, negatively or positively. A profile of five Australian-based gold producers is presented. The development of protocols to specifically deal with the highly regulated and ever changing, mining and environmental legislation. demonstrates mining companies can successfully opcrationalise the concept of sustainable development.

Jan 1, 1992

By J. N. Van der Merwe

Due to the approaching depletion of reserves in the Witbank Coalfield, and the fact that the Waterberg Coalfield is as yet under developed, there is increasing pressure to extend the lives of the operating coal mines in the Witbank Coalfield. One potential source of coal is the old pillars, often small and at shallow depth, that were not left with secondary extraction in mind. At face value, some of these pillars appear to be suitable for secondary mining due to their high safety factors. However, it is known that over time, these pillars have scaled and the current sizes are smaller than the as-mined dimensions. It is also known that at shallow depth, the overburden is often less likely to fail during secondary mining, resulting in high abutment loads on the unmined pillars. The paper proposes a systematic method to pre-evaluate those old pillars for the possibility of stooping. The method consists of elements of fundamental methods and newly developed technology. In essence, it revolves around using empirical methods to estimate current pillar dimensions, followed by numerical modelling to investigate the probability of progressive pillar failure and then fundamental methods to determine the limits of applicability of the numerical model.

Jan 1, 2012

Industrial minerals by definition are minerals used as part of an industrial process and usually are one of a number of components, eg finely ground Limestone is an extender in the manufacture of paint. They are normally non-metallic and non-fuel, but like all generalisations there are a number of exceptions. Take rutile û a source of titanium, a metal and also the raw material in the manufacture of titanium dioxide pigment. Industrial minerals under this general definition include construction and agricultural minerals. They are included in the same grouping, principally because their sources are similar and in many cases the raw material, example limestone, can be multi-functional. Calcium carbonate raw materials such as limestone, are used in a wide range of applications from industry as an inert filler, to agriculture as a 'lime' source and to construction and as an important component in the manufacture of cement. As far as this paper is concerned I will avoid discussing the agricultural or construction applications, including burnt lime production.

Jan 1, 1985

horizontal-type classifier prior to charging into a blastfurnace.

Apr 1, 1995

The Kalgoorlie Tailings Retreatment Project (or "Kaltails") involves the reclamation and retreatment of approximately 50 million tonnes of gold tailing situated on the Golden Mile at Kalgoorlie, Western Australia. Tailing is reclaimed and retreated at the rate of 42 million tonnes per annum. The project is a Joint Venture between Poseidon Limited and Gold Corporation, with Poseidon being the major participant (90%) and manager of the operation through its wholly owned subsidiary Kaltails Mining Services Pty Ltd. The marginal nature of the tailing retreatment project dictated that a detailed feasibility study be undertaken. Extensive sampling and metallurgical testing of the tailing permitted the development of an optimum economic processing route. A sensitivity analysis undertaken as part of the feasibility study indicated the project to be very sensitive to gold price and unit operating cost variations, and relatively insensitive to capital cost variations.

Jan 1, 1990

By S. J. Page, R. A. Jankowski, J. A. Organiscak

The U.S. Bureau of Mines investigated the relationship of bituminous coal seam parameters and the amount of airborne respirable dust generated at longwalls. Dust and coal samples were obtained from 20 longwalls operating in geographically representative coalfields throughout the United States. Statistical analyses of coal seam parameters and airborne respirable dust measurements indicate a likely causal relationship between seam type and respirable dust. Low-ash, high-volatile coal seams were associated with higher airborne respirable dust levels. A negative linear correlation (significant at the 95-pct confidence level) was observed between the seam's ash content and airborne respirable dust, explaining up to 18 pct (R2 = 0.18) of headgate dust level variation and up to 15 pct of tailgate dust level variation. Volatile matter was found to have a positive linear correlation with tailgate dust level, explaining 16 pct of the variation. Further data examination indicates that these relationships with dust are most likely nonlinear, because of improved R2 values over the linear correlations. However, a notable portion of longwall dust production is influenced by other operational parameters, so additional research under more controlled conditions is needed to determine the seam's causative functions.

Jan 1, 1992

"AQUILA Mining Systems Ltd. is a Canadian company that designs and develops monitoring, control and navigation systems for the surface and underground mining industries. In 1992, AQUILA Mining Systems began the development of technology for monitoring, controlling and positioning mobile mining equipment. In 1993, AQUILA completed its first field test with GPS receivers onboard ablasthole drill, and thus demonstrated the viability and strategic relevance of this technology in surface mining. Since then, AQUILA has installed GPS-based technology on drills and shovels in several Canadian mines. This paper will review the development of these systems and discussthe benefits the mining industry could realise through their production implementation."

Jan 1, 1997

By S. G. Ozkan

An investigation was carried out into the effect of physical parameters, such as particle size of the sample, residence time, solid/liquid ratio and impeller speed in the flotation cell, on the solubility in soft tap-water of colemanite (calcium-bearing borate) from Emet, in Turkey. Solubility increased steadily with residence time from 5 to 20 min but only minimally thereafter. There was a similar increase with impeller speed from 500 to 1 500 rev/min, beyond which a solubility of around 1.05 g/l was again established. There was a slight decline in solubility as the solid/liquid ratio was increased from 1 to 30%, with stable values around 1.05 g/l at a 20% ratio, while a sharp decrease was observed with decrease in size down to the -20 micrometre fraction. The effect of solubility should be taken into account if the application of a wet-processing method is being considered for the ore, while it can also result in losses of material during handling and storage

Jun 21, 1905

By A. McGarr

The shear stress t that can be sustained by the rock mass in the environs of a mining-induced earthquake controls the near-fault peak ground velocity v of that event according to v=0.25(ß/G)t, where ß is the shear wave speed and G is the modulus of rigidity. To estimate t at mining depths, I review the results of four studies involving Witwatersrand tremors that relate to the bulk shear strength. The first and most general analysis uses the common assumptions that the seismogenic crust is pervasively faulted, has hydrostatic pore pressure before mining, and an extensional stress state that is close to failure. Mining operations reduce the pore pressure to zero within the mine and redistribute the stresses such that, in localized regions, the state of stress is again at the point of failure. Laboratory friction experiments can be used to estimate t in the zero-pore-pressure regime. Second, model calculations of states of stress in the vicinity of mining at about 3 km depth indicated the shear stress available to cause faulting near the centre of a distribution of induced earthquakes. Third, laboratory experiments combined with microscopic analyses of fault gouge from the rupture zone of a mining-induced event provided an estimate of the average shear stress acting on the fault to cause this earthquake at a depth of 2 km. Fourth, moment tensors determined for mining-induced earthquakes usually show substantial implosive components, from which it is straightforward to estimate t. These four different analyses yield estimates of t that fall in the range 30to 61 MPa which implies that near-fault particle velocities could be as high as about 1.5 m/s. To the extent that the causative fault ruptures previously intact rock, both t and v, in localized regions, could be several times higher than 61 MPa and 1.5 m/s.

Jan 1, 2002

By E. Chin

The only economically significant mineral exploited in Banglades - during 1981 was natural gas. Nitrogenous fertilizer production was important to the agricultural sector and was totally dependent on the natural gas for fuel and raw material. Domestic cement plants were also fu pled by natural gas. The flat river-delta terrain for most of Bangladesh makes the potential for discovering major mineral deposits poor. No large deposits of metal ores have been found and only in the small hilly southeastern section of the country is there even much chance of finding any. Heavy mineral sand deposits may eventually be exploited along the Chittagong coastline. There is a good potential for crude oil discoveries. The Bangladesh economy has been heavi¬ly subsidized by billions of dollars of foreign aid since the country's inception. A World Bank report recommended total aid needs of over $2.6 billion in fiscal year (FY) 1980-81. It received commitments for barely over one-half that amount.

Jan 1, 1983

An intensely sheared and mineralized zone occurs in the quartz dolerite greenstone (or younger greenstone) mass on the western limb of the Kalgoorlie syncline. This zone comprises the western part of the Golden Mile and has produced the greater part of the 33,000,000 oz of gold produced to date from the main mining belts. A study of the general geological and structural features suggests that the lode shear system will continue southward on a pitch similar to that of the main syncline. Although payable ore has been found recently further to the south, the expectation of large quantities extending southward from the present mining areas is problematical.INTRODUCTIONUntil the late 1930's the principal mining activities in the western lode system were centred on three major ore-shoots formed on the No. 4, No. 3 and to a lesser extent on the No. 2 lode shears (Fig. 1). With the gradual reduction of grade in depth on these main ore shoots, increasing attention was paid to the "Minor Lode" system of lode shears known to exist in the same area. A large quantity of payable ore was found on these "Minor Lodes" particularly in the central part of the mining area. In recent years more attention has been given to exploration in a southerly direction.ROCK TYPES AND STRUCTURESThe western system occurs on the western flank of a dragfolded, south pitching syncline. The rock succession consists of Black Flag sediments overlying the younger greenstone horizon which overlies the fine grained older greenstone horizon. The axis of the syncline is regarded as a tight infold of the overlying Black Flag sediments. This infold has been faulted and intruded by albite porphyry resulting in the formation of a composite body of slates...

Jan 1, 1964

THE Yallourn chimney has aroused interest, as it is, for the time being, the tallest structural erection in Australia. Its height was not decided on, however, with the object of breaking records, but is purely incidental to the purpose which it serves. Theboiler plant at the briquetting works (first instalment) consists of five Babcock and Wilcox land-type water-tube boilers, each of 4510 sq ft. heating su:r£ace and 225 sq. ft. grate area in the form of step grates. Four boilers will normally produce 73,000 lb. of steam per hour at a gauge pressure of 265 lb. and a temperature of 6500 F., the fifth boiler being a reserve. Each boiler will consume about 100 tons of Yallourn coal per 24 hours. Provision is made for future installation of economizers, should it be found desirable. Designing for this condition, and allowing for a waste gas temperature of 3500 F. and an air temperature exceeding 1000 it was found necessary to have a draft of about 1.3 in. (water gauge) at the base of the chimney, and to deal with about 2000 cub. ft. of gases per second. Estimates were made of the cost of providing the necessary draught by means of fans and by means of a tall chill).ney. The annual charges of the two methods differed only slightly, and the tall chimney wasselected as being the more general practice in briquetting factories.Estimates were prepared for brick and concrete chiIlllleys. Yallourn bricks at that time were hand-made, and, while very suitable for domestic work, were not capable of withstanding high compressive stresses. The chimney design to suit these bricks thus required to be on very ample lines, resulting in high cost. Machine-made bricks from Melbourne would cost about £5 10s. per thousand on the site, with extra for radials, so that high cost again resulted. On the score...

Jan 1, 1924

By Frank Callanan

The Ameristar Casino expansion project included the design and construction of a 25-story hotel and 9-story parking structure expansion. The site is located in a floodplain on the banks of the Missouri River in Saint Charles, Missouri, where the underlying soils are potentially liquefiable. The geotechnical engineer performed subsurface exploration and analysis, which included site-specific seismic response and liquefaction, and provided geotechnical design recommendations. In the event of an earthquake, post-liquefaction settlement was calculated to be approximately 14 inches. Additional project constraints included wetlands protection, construction adjacent to the existing facility, flood protection and river bank stability. Because of the liquefaction issue, the geotechnical engineer consulted with a specialty geotechnical contractor on ground improvement methods. This consultation led to a proposal to eliminate deep foundations from the design and support the structures on shallow and mat foundations. The geotechnical engineer assisted the design team with foundation design analysis and value engineering assessments. Together with the project team, the geotechnical engineer used the data to evaluate foundation options and construction methods to overcome the site challenges and concluded that ground improvement was the optimum course of action. Because of the nature of the site constraints, a number of ground improvement methods were needed. The geotechnical engineer evaluated the methods proposed by the geotechnical contractor and provided the technical specifications for the ground improvement bid package, which included vibro-compaction, compaction grouting and micropiles. The ground improvement allowed for the use of shallow foundations (mat and spread footings), which provided the client with significant time and cost savings over the deep foundation alternatives.

Jan 1, 2009

Autogenous-Carrier Effect and Gangue Influence in Fine Particle Flotation of Ilmenite/Titanaugite System

Sep 13, 2010

By S M Richardson, A W McNeill, J B. Gemmell

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The Hellyer, Fossey, Que River and Mount Charter volcanic-hosted massive sulfide (VHMS) deposits occur within the Que-Hellyer volcanics of the Mount Read volcanics, Tasmania. These deposits occur along a 6 km strike length and are hosted by the same stratigraphic unit. We use a combination of whole-rock geochemistry, short wavelength infrared (SWIR) spectrometry, laser ablation inductively coupled plasma mass spectrometry (LA-ICP-MS) analyses and compiled historic whole-rock geochemical data to develop district-scale vectors towards VHMS mineralisation.Strongly sericite and K-feldspar altered rocks concentrate along a linear trend from Hellyer, through Que River, to Mount Charter. Ishikawa alteration index values and whole-rock major and trace element concentrations provide exploration vectors towards mineralisation on a regional scale as significant enrichment and depletion trends. On a deposit scale, composition variations in white mica (sericite alteration), chlorite and K-feldspar are observed and reflected in whole-rock geochemical variations. Regional SWIR data from drill core support the prevalence of phengitic mica and high-Mg chlorite within footwall alteration halos and highlight the main upflow zones of hydrothermal fluids in the VHMS district. The combined use of regional whole-rock geochemistry, SWIR and mineral chemistry is an effective way to highlight prospective areas for VHMS mineralisation in a mature exploration province.CITATION:Wu, S, Gemmell, J B, McNeill, A W and Richardson, S M, 2015. Exploration implications from variations in whole-rock and mineral chemistry around the volcanic-hosted massive sulfide deposits of the Que-Hellyer volcanics, Tasmania, Australia , in Proceedings PACRIM 2015 Congress, pp 85–90 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

Atlas Copco Construction and Mining Australia identified a number of issues in regard to the skill levels, labour turnover and productivity of our service technicians. In 1994 we were experiencing a labour turnover rate of 42 per cent per annum amongst our technicians. Exit interviews were held with each individual and one of the major areas of dissatisfaction was the degree of product training provided on our equipment, compared to what is required to be competent across the range of our products. These tradespersons were prepared to accept the reduced remuneration that an OEM offers, for the benefit of comprehensive, professional training that, in theory, could be provided. The truth is that we were achieving approximately 40 per cent of our target for training hours because of the demands of field service, pre-deliveries, etc. So, the summary was the same as the industry was experiencing at that time because of skilled labour shortages, production demands, etc people were employed and thrown in at the deep end. A recipe for failure that will be successful every time.

Jan 1, 1998

By Wittenberg J. C, Reid A. F

A method is described for the rapid and effective production of polished section mounts of ore and mineral particulates to the standards required for automated image analysis. This requires mounting without segregation of particles by mass or density, and it is also preferable to avoid having particles in contact so that they can be recognised as individuals. To achieve this, the particle samples are first split to an appropriate degree in a rotary riffle, and the sub-sample mechanically diluted and thoroughly mixed with an inert filler of the same size range as the particles. Just sufficient epoxy resin is added to make the mixture fluid. During setting, the ore particles are mechanically supported by the inert filler particles, thus maintaining the particles in a random three-dimensional distribution. A rapid two-stage grinding process, based on the successive use of 600 mesh silicon carbide and 1200 mesh (10 um) corundum on cast iron plates, is followed by three stages of mechanical diamond polishing on cloth laps. Hand polishing is entirely avoided, as is the use of papers.

Jan 1, 1984