Search Documents

By P. Foster, A. Burton

Over the past decade there has been a great deal of research into the use of virtual reality (VR) and computer graphics in the mining industry. Much of this has led to developed applications including training simulators and accident re-construction. One other area where there is considerable potential for virtual reality is that of mining ergonomics. This paper identifies those common ergonomic limitations associated with mining equipment that can be effectively modelled using VR techniques. From this, two simple models have been developed namely (i)remote control continuous miner operation and (ii) free steered vehicle sightlines, which demonstrate the practical use of VR in this area.

Jan 1, 2003

By Syd S. Peng

Mountaintop removal (MTR) mining started in West Virginia nearly 30 years ago. This surface mining method can extract multiple coal seams as thin as a few inches in whole and minimum rock dilution in very steep mountainous terrain. MTR is highly efficient, even if coal seams are in close proximity and small in a real extent. Consequently, MTR has been widely used in the Central Appalachian coalfield (mainly Kentucky, Tennessee, Virginia and West Virginia) with great success. In that respect, there has been no demand for research and little scientific research has been performed to investigate its impact on the surrounding area. During the past two years, however, the debate over MTR mining has grown quickly and has become very intense. This article describes chronologically issues raised by various parties, legal actions, impacts on mining permit applications and research projects developed to address the issues.

Jan 1, 2000

By H. Y. Sohn, Hang Goo Kim

Computer simulations were carried out using calcium ferrite slags containing 25 wt% CaO, and the results compared with those obtained using fayalite slags. There was little difference in overall elimination of Pb and Bi, but elimination of Sb and As was much lower with calcium ferrite slag. When calcium ferrite slag is used only in the converting stage and fayalite slag in the smelting stage, as in the Mitsubishi process, the contents of Sb and As in the blister copper can be kept to reasonable levels. This allows advantage to be taken of the considerably higher iron oxide-holding capacity of calcium ferrite slag than of fayalite slag at the high oxygen potential under converting conditions, thus preventing precipitation of magnetite. Satisfactory agreement was obtained between predicted values and observed data from a Mitsubishi converter

Jun 18, 1905

By M. R. Saharan

A brief overview of rockburst control measures is presented. The paper then elaborates on one key rockburst control measure, which is known as destress blasting. A historical background of the technique is presented in order to understand different aspects of its field application. The publication enumerates key aspects of the technique as being used in practice in South Africa and North America. The paper also presents an analysis of three case studies in order to demonstrate difficulties associated with the field application of distress blasting in hard rock mines.

Jan 1, 2006

By David J. White

The decreasing availability of land in urban areas, and the increasing demand for urban development is leading to the construction of taller and heavier buildings at increasingly marginal sites. Such structures usually require founding at depth and modern construction methods are making the economics of piled foundations ever more attractive (Salgado, 1995). However, the urban environment is not suited to pile driving. Conventional dynamic installation techniques (i.e. drop hammer or vibro-piling) induce vibrations and settlement in a zone close to the pile, and cause noise and dust pollution. Damage to existing structures resulting from pile driving vibrations is not uncommon (Tomlinson, 1986).

Jan 1, 2000

THOSE who dabble in mining are no exception to the general rule that persons who know a little of a subject are apt to think that they know all about it. Some colour may be lent to the belief that anyone may succeed in mining when we hear stories ofsuccessful diggers and others who have accidentally dropped on to something good through no foresight on their part; but we seldom hear the contra account of the far larger number who fail. Those who go more thoroughly into the subject, and take up mining as a profession, know very well that it is not one that can be carried out successfully by rule of thumb, but when they point this out to the public they are credited with trying to make it a closed profession; and outsiders are for ever trying to find out the "trade secrets," at the same time spurning the main one, which is hard study, experience, and the ability to apply their knowledge. The average mining man is not rich. When he amasses a fortune it is generally through speculation rather than professional work, thought no doubt his technical knowledge may have assisted...

Jan 1, 1910

By S. K. Gilman

Zircon (ZrSiO4) sand production of about 1.1 Mt/a(1.2 million stpy) predominates the global supply of zirconium minerals. Baddeleyite (ZrO2) contributes less than 1 percent of supply. Zircon is almost exclusively produced as a co-product from the mining of titanium minerals, mainly from mineralized beach sands. In 2004, there were a number of new projects under consideration that were more dependent on zircon revenue than for titanium minerals. This reflected sustained higher zircon prices and forecast ongoing supply shortages in the absence of major new discoveries.

Jan 1, 2005

By B. J. Moore

The Bureau of Mines has estimated helium resources of the United States at 727 billion cubic feet as of January 1, 1979. These resources are divided into four categories in decreasing degrees of assurance of their existence: (1) Helium in storage and in measured natural gas reserves, 185 billion cubic feet; (2) helium in indicated natural gas resources, 150 billion cubic feet; (3) helium In hypothetical natural gas resources, 186 billion cubic feet; and (4) helium in speculative natural gas resources that makes up the remaining 206 billion cubic feet. The identified helium reserves, which are made up of that in measured and indicated natural gas categories, are further divided into depleting, non- depleting, and stored classifications. The depleting resources are those that are associated with natural gasfields that are, or will be, produced for the natural gas they contain. All of the helium in undiscovered natural gas resources are included in this classification. These depleting resources comprise 600 billion cubic feet of the total resource base. The nondepleting helium resources are estimted tototal 88 billion cubic feet. There is 39 billion cubic feet of helium in storage in Cliffside gasfield near Amarillo, Tex.

Jan 1, 1980

By L Spencer, H Zwingmann, I Graham, D Cendon, B Kelly, D Burkett, F Lau, P Lennox

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The Kulumadau deposit represents an intermediate-sulfidation epithermal gold deposit (3.8 Mt at 2.3 g/t, Ag:Au = 1). Mineralisation is primarily confined to hydrothermal breccias within pre-existing fault zones, where it is disseminated throughout a hydrothermal matrix comprising chlorite-quartz-adularia-illite-I/S clays-calcite-pyrite. The host sequence represents numerous mid-Miocene pyroclastic flow eruptions within a tectonically active emergent shallow marine to subaerial depositional setting. Subsequent growth faulting was responsible for debris avalanches, which were subsequently cut by reverse faults. Faults were exploited by hydrothermal fluids, with the heightened porosity at the juncture between faults and debris material facilitating boiling of the ore constituents. Fluid inclusion studies suggest that fluid mixing between meteoric fluids and magmatic fluids, accompanied by boiling, were the primary mechanisms for gold deposition. The occurrence of anhydrite/gypsum as late-stage veins and their sulfur and oxygen isotopic values indicate post-mineralisation mixing of sea water with hydrothermal fluids.CITATION:Burkett, D, Graham, I, Spencer, L, Lennox, P, Cohen, D, Zwingmann, H, Lau, F, Kelly, B and Cendon, D, 2015. The Kulumadau epithermal breccia-hosted gold deposit, Woodlark Island, Papua New Guinea, in Proceedings PACRIM 2015 Congress, pp 205–212 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By R. K. Linn

The New Idria Mining and Chemical Co. owns and operates the New Idria mine in southern San Benito County, Calif. During 1957-59, the New Idria mine was the largest producer of mercury in the United States and its alltime production of over a half-million flasks was exceeded only by one mine. It is one of the oldest and most consistent producers in California. With the exception of 1921-22, the mine has an annual production of mercury dating back to 1854. This paper by the Federal Bureau of Mines describes the exploration, development, mining, and furnacing of mercury ore at the New Idria mine. Figure 1 is a view of the furnace plant of the New Idria mine. The purpose of this report is to promote the development and conservation of our mineral resources by dissemination of technological information on mining and processing procedures, and related practices at operating mines.

Jan 1, 1961

By J. Wagner, P. Eger

Although lifetime estimates for sulfate reduction based on total substrate carbon typically range from 20 to 30 years, field and laboratory experiments showed that rates of sulfate reduction decreased over time as readily available organic material was consumed. When the rate of acid input exceeded the rate of sulfate reduction, alkalinity was removed from the substrate, pH decreased and metals increased. Output pH increased from 4 to over 6 after the system was shut down for several weeks and the rate of acid input was reduced. Successful long term treatment requires a design based on the input pH and the long-term organic decomposition rate.

Jan 1, 2001

By D. M. Doyle

"In this paper I will summarized the Falconbridge Nickel Mines1) energy costs and consumption data by fuel, process, cost centre and estimate our future costs and consumption patterns 2) detail the distribution of electrical energy 3) distribution of other forms of energy 4) describe present and planned energy conservation schemes; and 5) discuss economic justification and responsibility.There is sufficient material in this presentation to warrant several technical papers, however we felt that an overview of all our data and endeavors on the subject, would be most beneficial to those companies formulating energy conservation plans. The data briefly referred to in this slide presentation can be found in the technical paper.Over a five year period, total energy costs will vary between $63 and $94 MM depending on the future rate of energy cost escalation. An unrealistic 32% reduction in energy consumption is required to hold our own in the years ahead whereas an attainable 10°;, reduction in energy consumption would save $9 MM over this five year period.Total energy consumption, tonnage of ore delivered to plants and their ration BTU’s per ton of ore, are graphed for the years 1973 through 1976 and forecasted for the 1980’s. In 1974 we along with other member companies of the Mining Association, determined our purchased energy per ton consumption rate and set, as our goal, a 20% reduction by 1980. The dotted lines calculated from the energy audit, based on 1976 data shows there is a potential for a 10% increase in energy per ton. This could result from a lower than forecasted mining rate and operation of the new roasting, electric furnace and acid recovery facilities installed for environmental considerations at designed capacity."

Jan 1, 1978

By Warren L. J

The effectiveness of shear-flocculation as a method for upgrading simple mixtures of ultrafine (1-11 \lm) scheelite and garnet was evaluated. Statistical methods were used in the design and analysis of the main test program.The stirrer speed, stirring time, and initial weight ratio were all found to have significant effects on both the recovery and grade of the floes produced. The particle sizes also had an effect on the final grade. There were several important interactions between factors which also affected the results. Optimum conditions for shear-flocculation were established, and under these conditions about 80 per cent of the scheelite could be recovered at a grade which depended on the composition of the starting mixture. Starting with mixtures containing 10 and 50 per cent scheelite, the best final grades were between 20 and 50 per cent and between 70 and 90 per cent respectively, the actual value depending on the particular combination of particle sizes.

Jan 1, 1977

By Wawa Jaka Sungkawa, Slamet Rachman Jaka, Tom Dermody

Nowadays, with such a focus on environmental protection, surface mining activities have come under pressure to ensure their activities do not adversely affect the local surroundings. As part of the extractive process, blasting activities are an integral part of a mining company’s operational cycle. Consequently achieving beneficial blast results while complying with environmental requirements has become a key focus. This especially is the case when firing blasts within close proximity of residents where additional control measures need to be implemented to control vibration. One case where this occurs in Indonesia is in the Paringin Pit, one of the operational areas of the company's. The pit has complex geological conditions and is surrounded by several residential areas. Between 2014 to 2017 there were 12 cases of ground vibration exceedance due to blasting. As part of a continuous improvement project the company's targeted minimizing the vibration exceedance in this area. A project was undertaken to research and develop a method to confidently predict vibration. It was decided that the scaled distance formulas were not adequate to predict vibration when using non-electric detonators, as accurate wave propagation could not be achieved. The problem is how to manage of complex geology condition related with wave propagation in ground vibration control. Geological condition mapping with specific spatial range can and combine with Signature Hole Analysis be a solution to make wave propagation easier to accommodate in ground vibration control. With this new approach geological condition mapping with specific spatial range was produced that would minimize vibration while ensuring beneficial blast results. Introducing the new prediction produced nil cases of vibration exceedance in 2018 and beyond and proved that the Signature Hole Analysis in specific spatial range of geological condition is the preferred method to optimize blast result and maintain vibration control.

Flue dust from the sintering of base metal sulphides was leached to remove cadmium and arsenic. Leach liquor contained cadmium, zinc and small amounts of other base metals as chlorides. Results are reported of the use of a cation exchange resin Zeocarb 225 to separate the base metals from the arsenic. The resin was eluted with sodium chloride or sulphate to give a solution of relatively concentrated cadmium suitable for recovery by zinc cementation. The limited solubility of sodium sulphate presented some practical problems which were investigated. Another problem was the precipitation of lead sulphate in the resin during elution.INTRODUCTIONWhen lead-zinc sulphides are sintered prior to smelting, the gases passing to the flue are mainly uncondensable but contain a certain proportion of sublimates and dust particles which deposit in the flue or are carried, after condensation in the gas stream, to some form of dust extraction equipment.The recovered dust is a complex mixture of base metal sulphates, sulphites, sulphides, chlorides and oxides, the composition depending on the original concentrates. A large proportion of the cadmium and some of the arsenic originally in the concentrates finds its way to this flue dust, the treatment of which can be a convenient means of removing these elements and controlling their concentrations in the main lead-zinc smelter circuit. However, disposing of this material represents an appreciable waste of base metals as well as a serious toxicity hazard.Sulphide Corporation Pty. Ltd. was faced with this problem in planning the flow sheet of the new lead-zinc smelter at Cockle Creek, N.S.W. From a test run carried out on a pilot plant at Avonmouth, U.K., using a mixture of lead and zinc concentrates, a sample of dust was obtained for...

Jan 1, 1960

By Felix A. Vogel

Rutile concentrate, used in the manufacture of welding rode, smoke-screen chemicals, and alloys, is being produced by the Titanium Alloy Co. of Arkansas at its mine and. mill in Magnet Cove. The company estimates a substantial reserve of recoverable rutile. This is a new operation, and production figures are not known. Previous operations had stripped the placer material, leaving the underlying mineralized zone. INTRODUCTION This report describes the mining and milling; operations of the Titanium Alloy Co. of Arkansas. The property was examined by the author on March 4, 1942, and subsequent dates. J. A. Wood, general manager, was very helpful in supplying information.

Jan 1, 1944

By Alastair Grogan

In October of 2002, the author was retained by Public Works and Government Services Canada, on behalf of the Department of National Defense, to design, construct and test the effectiveness of a bubble curtain system at an underwater demolition range, near Victoria, BC. The purpose of the bubble curtain was to reduce the potential for fish mortalities at the site. This paper presents some of the elements of the design, along with the results of overpressure monitoring during blasting and compares the results of fish mortality and animal behaviors with and without the bubble curtain in operation.

Jan 1, 2005

Enhancement of Energy Efficiency in Fine Grinding of Copper Sulfide Minerals Using a Pilot-Scale Stirred Media Mill - IsaMill The mineral liberation size of run of mine ores has dramatically reduced over recent years. As a result, the demand for fine grinding which is the most energy-intensive form of grinding has markedly increased in the minerals industry. Furthermore, the fine grinding costs increase exponentially with decreasing product particle size. As a result of the increased energy requirement for fine grinding, it is desirable to optimise fine grinding processes such as stirred media milling (ie IsaMill) to enhance energy efficiency, throughput and the product fineness. In the present study, the influence of slurry rheology, grinding media type and grinding media-to-feed size ratio on energy efficiency in a pilot-scale IsaMill was investigated under certain industrially relevant pulp processing conditions. It was shown that a critical rheological state existed, below which the energy required to achieve an 80 per cent passing (ie P80) 20 ¦m product size was unaffected by shear rheology (ie apparent viscosity and shear yield stress) whilst above which the grinding energy required increased dramatically with increasing shear rheology. Colorado River sand (3.35 mm) showed higher energy efficiency than MT1 ceramic media (2.5 mm) for a target P80 of 20 ¦m in the solids concentration range of 38 to 55 per cent by weight, but the former experienced more than four times the wear rate of the later. The high wear rate of the Colorado River sand may be due to its much lower hardness. For feeds with an 80 per cent passing (ie F80) 70 to 110 ¦m, 2.0 or 2.5 mm MT1 media appeared to be more energy efficient than 3.5 mm MT1 media whilst a media-to-feed size ratio of 41 to 53 is applicable for ~50 ¦m (ie F80) feeds for efficient grinding.

Sep 13, 2010

By Thomas W. Camm

This study was done to evaluate the costs of various dumping operations at waste and spoil piles. It has been theorized that accidents associated with dumping operations might be reduced by short-dumping rather than edge-dumping, but many operators have been reluctant to use short-dumping because they believe it is not as cost effective as edge-dumping. To evaluate this perception, researchers at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health reviewed the costs of various dumping methods at waste and spoil piles. The study found that overall cost differences between the two methods were not significant in most cases. However, while overall cost differences between the two methods appear small, capital costs could be more significant when short-dumping if numerous dump sites are used concurrently. The choice of which method to use should be based on considerations of the safety of dozer and truck operators.

Jan 1, 2000

By Jozef F. Zurawski

River Des Peres Foul water Interceptor (Skinker–McCausland Tunnel) is a gravity sewer tunnel constructed to eliminate dry sewage overflows during high river stages and to improve the wastewater collection and treatment. The original 78-inch (2m)finished diameter Skinker-McCausland Tunnel started as a 21,500 feet (6.5km)interceptor with 13 work, drop and access shafts. The tunnel constructions included soft ground, mixed face and rock tunneling in karst formation with maximum overburden of 175 feet (53m). Due to the success of the project, the tunnel alignment was extended another13,361 feet (4.1 km) and 7 new structures by negotiating two additional segments with the contractor and the designers.

Jan 1, 2001