Search Documents

By J. R. Ross

Recovery of uranium from slightly alkaline mine water, available in the Ambrosia Lake district of New Mexico, was studied using countercurrent ion exchange columns developed by the Bureau of Mines. Approximately 5 million gallons of mine water containing 9 to 12 ppm U308 was treated by ion exchange using a 14-inch-diameter absorption column composed of five or six compartments each 4 feet deep. Uranium recoveries averaged in excess of 98 percent at solution flows ranging from 15 to 25 gallons per square foot per minute and resin loadings up to 3.6 pounds of U.08 per cubic foot. In subsequent tests, loaded resin was continuously eluted in a countercurrent elution column with a diameter of 4 inches and containing a bed of resin 9 feet deep. The resin was eluted to a residual loading of less than 0.06 pound of U305 per cubic foot, at a resin-retention time of 224 minutes, using only 1.9 volumes of 1.1 M NaCl-0.05 M NaHCO3 solution per volume of resin. Compared with existing ion exchange practices for recovering uranium from mine waters in the Ambrosia Lake district of New Mexico, use of these improved ion exchange contactors would reduce ion exchange resin requirements at least 70 percent and allow further substantial reductions in capital and operating costs.

Jan 1, 1971

By David Dardick

Tround International Inc. is developing rock excavation and drilling devices which utilize a simple patented mechanism for firing frangible projectiles. This system launches a salvo of three projectiles with every shot in automatic sequence. Studies conducted by Physics International Inc. have demonstrated that firing projectiles into hard rock such as granite creates fragmentation which is much faster and cheaper than conventional drilling and blasting. The Tround salvo approach enhances this further by a controlled stresswave interaction created by a slight time difference during impact of the individual projectiles. The University of Maryland is conducting additional studies to optimize these parameters.

Jan 1, 1981

By D. Olsen, S. Cole, J. Strid, G. Colzani

This paper focuses on the underground tunnel work at the Hollywood Water Quality Improvement Project (HWQIP) in Los Angeles, CA. The HWQIP is being constructed to provide a water distribution system to bypass the existing Hollywood Reservoir System, which supplies drinking water for 500,000 people. The major project features include, a 2.9-meter diameter 1,829 meter long bypass tunnel, a 1.8-meterdiameter 366 meter long utility tunnel, 3 jack and bore tunnels, two 136 million liters underground circumferentially wrapped pre-stressed concrete water storage tanks, associated piping, and mechanical facilities. The physical project location coupled with strong community involvement and stringent environmental concerns was a considerable driving force for this project located in the Cahuenga Pass area of the Hollywood Hills north of Los Angeles, CA.

Jan 1, 2001

By C. E. Wood

A special appropriation made by Congress in July 1940 provided funds for the investigation of methods for recovering manganese from low-grade [ ] domestic deposits. These funds were assigned to the United States Department of the Interior, Bureau of Mines. A committee, identified as the Technologic Committee on manganese of the National Research Council, National Academy of Sciences, was appointed to recommend the allocation of the funds for investigation of the more promising projects.

Jan 1, 1942

By C. E. Wood

A special appropriation made by Congress in July 1940 provided funds for the investigation of methods for recovering manganese from low-grade [ ] domestic deposits. These funds were assigned to the United States Department of the Interior, Bureau of Mines. A committee, identified as the Technologic Committee on Manganese of the National Research Council, National Academy of Sciences, was appointed to recommend the allocation of the funds for investigation of the more promising projects.

Jan 1, 1942

By Michael B. Gilbert

The Woodbury L-73 Tunnel involved the design and construction of a 96-inch tunnel driven through 8,080 lf of very difficult ground conditions. Anticipated ground and groundwater conditions consisted of potentially flowing silty sand with cobbles and boulders, mixed face of sand and sandstone and full face of the St. Peter Sandstone. Actual conditions were similar, although the quantities did change from bid quantities. This paper presents the approach used for development of the GBR regarding risk management. The means of arriving at a fair compensation for variances from the baseline values to address the actual encountered tunneling behavior of the soil, boulder count and its effect on production rates are presented.

Jan 1, 2008

By Sune Eriksson, Stig Peterssonsune, Christer Fridfeldt

"Boliden Metal Corporation has developed a technique to treat complex copper concentrates containing large amounts of lead, zinc, arsenic, antimony and bismuth which cannot be treated in conventional smelters due to the impurities.Tests were carried out to treat such complex copper concentrates in the TBRC. They were performed in a pilot-plant TBRC with charges of 5 tons. These tests resulted in a new method to treat complex copper raw materials and produce a blister copper low in impurities. The background and data from the test work are presented as well as a flowsheet for a full-scale process.IntroductionThe Ronnskar Works is situated on the coast of the Gulf of Bothnia, 40 miles east of the Boliden Mine. Smelting began at Ronnskar in 1930 to process the complex ore extracted from the Boliden Mine. The Ronnskar Works has subsequently developed into a relatively integrated smelting plant.Copper and lead sulphide concentrates from Boliden's own mines as well as purchased copper raw materials are processed. The main products are refined copper and lead, but full utilization of the raw material also yields other metals and some metallurgical and chemical by-products. The products include gold, silver, zinc clinker, white arsenic, arsenic salts and arsenic metal , selenium and selenium compounds, nickel sulphates, sulphuric acid and liquid sulphur dioxide."

Jan 1, 1981

By E. L. Garton

Michigan is becoming one of the important oil-producing States of the country. The amount of crude oil produced within its boundaries has increased from only 4,000 barrels in 19253/ to nearly 16 million barrels in 19935.4/ The Bureau of Mines method of crude-oil analysis and classification-indicates that the oils from the several producing fields are predominantly paraffin-intermediate-base, wax-bearing crudes. In general, they will yield 25 to 35 percent of highly paraffinic gasoline and about the t- me amount of kerosene and gas-oil combined, 7.2 to 15 percent of lubricating oil stock, and 20 percent of residuum with a carbon residue or about 6 to 7 percent. In addition, there appears to be some correlation between certain properties of the crude oils and both the geographical location and geological structure of the oil-producing areas within the State. These general conclusions are based on the analytical data presented in this report, which is one of a series of papers that record the general characteristics of crude oil from the many producing fields of the United States. This report discusses briefly the oil fields of Michigan and the characteristics of the crude oils produced from them. The analyses of 15 samples are given. These samples were obtained from 13 fields in 9 counties in the lower peninsula and represent crude oils produced from the Berea sandstone, Upper Traverse and Traverse limestones, and the

Jan 1, 1937

By George T. Faust

The petrographer engaged in examining the products resulting from the beneficiation of ores, and rock minerals is constantly required to develop new means acid methods of assaying microscopically the results of such operations. From time to time investigators have published descriptions of apparatus that have aided in solving problems in processes of physical separation. Thus, in 1919, Coghill and Bonardi 3/ published a paper covering the application of the binocular microscope and camera lucida to the microscopic analysis of pulverized ores. Similar work has been published by Schneiderhohn 4/ Schwartz 5/, and Head and his associates 6/, 7/, 8/. The present paper goes further and considers application of the polarizing comparison-microscope to problems directly concerned with mineral dressing where it is desirable to compare analogous products, and in addition it suggests new uses in various related fields. This work was conducted under the cooperative agreements of the Southern Experiment Station of the Federal Bureau of Mines and the University of Alabama.

Jan 1, 1940

By G. W. Jones

During the course of an investigation by the Bureau of Mines into the causes, behavior, and control of anthracite-mine fires, it was observed that the carbon monoxide disappeared from a sealed fire area much more rapidly than could be explained on the basis of leakage of gases. Two suggestions were offered for this high rate of disappearance: (1) That the carbon monoxide, was oxidized at temperatures below 150° C. by either the anthracite or its ash (tests on many anthracites have shown that at temperatures above 150° C. carbon monoxide is liberated in the oxidation products when air is passed through it); (2) that the carbon monoxide was oxidized by micro-organisms present in the sealed area.

Jan 1, 1939

By H. Razavizadeh

The recovery of copper from oxide ores containing from 2% to 4.1% acid-soluble copper from the Sarcheshmeh mine in Kerman province of Iran was investigated by agitation leaching in sulfuric acid media. Quartz, as a major constituent, and malachite, as the major copper mineral, were identified in the ore by X-ray diffraction (XRD) and microscopic studies. A series of leaching experiments on the ore was performed over a concentration range of 10 to 20 g/L and temperatures from 15° to 50°C for a maximum of 3 hours. An initial high dissolution of copper was followed by a very slow reaction. By increasing acid concentration and temperature, the dissolution rate of copper was accelerated. However, by increasing acid concentration, the acid consumption of ores was also increased. Surface morphology of solid residues at various leaching times was examined with a scanning electron microscope (SEM). All SEM micrographs of the partially reacted particles displayed a needle structure. The kinetic studies showed that the malachite dissolution rate could be modeled in two stages. About 85% of the malachite dissolution occurred in Stage 1, while the remaining 15% occurred in Stage 2. The data obtained for the leaching kinetics indicate that the dissolution for Stage 1 was a diffusion-controlled reaction with an activation energy of about 20.6 kJ/mole, and the dissolution for the Stag 2 was a chemical-controlled reaction with an activation energy of about 87.6 kJ/mole.

Jan 1, 2008

By Eugene H. Skinner

This Bureau of Mines report describes the fieldwork and subsequent analysis to determine physical properties, stress distribution, and several aspects of rock behavior as a necessary evaluation for a typical mine opening. All work was done at a test site on the 3300 level, Crescent mine, Coeur d'Alene mining district, Idaho. Free field stress beyond the influence of the opening was also determined. Conventional overcore technique with the three-component borehole deformation gage developed by the Bureau of Mines was used in three drill holes. Three field verification tests were performed using a gage newly developed by the Spokane Mining Research Center in an approach herein termed "initial deformation method." Use of this method validated that aspect of overcore theory which predicts that similar deformation effect occurs in the wall rock around the perimeter of an opening in rock under stress. Also described are all drilling procedures and performances. Physical property determinations were made on rock samples obtained from the three overcore drill holes. Twelve physical properties with a total of [532] values were obtained at various drill hole orientations and depths. Exhaustive statistical tests were utilized in the analysis of these physical properties. Further elaborated are statistical inferences based on these analyses. Extensive analysis and interpretation of Crescent mine geology are also described.

Jan 1, 1974

By A. D. Davis, J. L. Sorensen, C. J. Webb

Environmental impacts from acidic mine drainage are growing national concerns that are particularly acute in the headwaters of the Rocky Mountain region. In the Black Hills of South Dakota, approximately one thousand mines are inactive or abandoned, most of them in the headwaters of major drainages. This paper examines the Bear Butte Creek basin, a heavily mineralized watershed with significant historical mining impacts and a surface gold mine permitted in 1997. The watershed loses its surface discharge to swallow holes in the karstic Madison Limestone. The integrity of the aquatic ecosystem was monitored with a suite of sitespecific bio-indicators. Stream surveys covered the entire reach of Bear Butte Creek from near its headwaters to the swallow holes in the Madison aquifer. Data from the stream surveys, water-quality sampling, and bio-indicator surveys clearly showed that water-quality impacts are limited mainly to Strawberry Creek and to the area of Bear Butte Creek near and downstream of the town of Galena.

Jan 1, 1999

By Leigh J. Wardle

This paper describes a numerical method for calculating the three¬-dimensional stresses and displacements induced by tabular excavations in a rock mass consisting of parallel layers of distinct material properties. The method is based on the superposition of numerical solutions for elementary displacement discontinuities in a parallel layered rock mass. The method can be used to analyse complicated excavation layouts such as those encountered in room-and-pillar or longwall mining. The method can automatically take into account the effect of the earth's surface. The method offers an economic and efficient solution to stress analysis problems which cannot be adequately modelled using two¬-dimensional methods and for which the expense of three-dimensional finite element or general boundary element analysis cannot be justified.

Jan 1, 1984

By David M. Langlais, Krystle Pelham

"Explosives used in blasting operations, natural and anthropogenic sources such as septic systems,fertilizers, and decomposing vegetation can potentially contaminate groundwater with nitrate in thevicinity of construction sites and make identification of blasting impacts difficult. Blasting operationsfor a private construction project in Windham, New Hampshire were indicated as the source of water quality impacts to private drinking water wells prompting the New Hampshire Department ofTransportation (NHDOT) to implement a proactive approach to limit the potential for impacts fromblasting for ongoing NHDOT projects. NHDOT has developed a baseline drinking water monitoringprogram designed to detect potential impacts and to ensure alternative drinking water is providedthroughout the construction phase of projects. In 2013, the U.S. Geological Survey (USGS) andNHDOT began a study to determine the source and fate of nitrogen compounds near blasting sites using a combination of isotopic, time series, geochemical, hydrologic, and geologic data. Approximately 1.75 million cubic yards (1.33 cubic meters) of rock were removed by blasting in several locations for roadway construction at a major highway construction site in southern New Hampshire."

Jan 1, 2016

By T Hughes

Upward pressure on all mining operations is coming from the triple bottom line. To some extent this is being offset by the rise in mineral prices, but this may or may not continue. The other serious issue facing all companies is the replacement of economic reserves as exploration levels over the past decade continued to decline in line with falling mineral prices. In order to underpin the sustainability of the mining industry it is necessary to continue to reduce cost, reduce the mine environmental footprint, whilst increasing community benefit. At the same time it is imperative that we increase the economic reserves. The highest risk is in adding new mineral discoveries as the strike rate for economic discovery decreases. Gekko Systems Pty Ltd recognises that the most simple and risk averse route to increasing economic reserves is to reduce cut-off grade in the mine, thereby bringing formerly uneconomic reserves into the economic category. We have been developing a new process flow sheet which embodies the triple bottom line and the issue of economic replacement of reserves. This paper describes this flow sheet and presents four examples where this concept is/can be applied to bring about triple bottom line benefits. Sustainability can only be assured if we are the ones in control of our environment, costs and reserves.

Jan 1, 2007

Terramin Australia LimitedÆs Angas Lead and Zinc Mine operates in the unique and picturesque environment of Adelaide Hills, 60 km South East of the Adelaide city centre itself. The mine was granted approval for construction by the South Australian Government in April 2007 and the Process Plant was constructed and commissioned in July 2008. This paper outlines the background to the plant design and the approval process given the close proximity to the local town of Strathalbyn, with a major focus on the commissioning learnings from the Concentrator startup for future reference and a review of the operational performance of the Concentrator throughout the first year of successful production versus design and expectations.

Jan 1, 2009

The principle activities of the Explosives Research Laboratory from July 1, 1961 to June 30, 1962, are described briefly in part 1. Part 2 gives short abstracts of publications that appeared during fiscal year 1962; in general, the research reported in these publications antedates the report period. Part 3 gives the results of an investigation which, although too limited to warrant separate publication, merits presentation in some detail because of current interest in ammonium nitrate-fuel oil compositions.

Jan 1, 1964

By Irving Palmer

DURING the past 15 years in this country there have been few additions to the literature of lead smelting. After the consolidation of the principal smelting companies at the beginning of this period it became the policy of the larger company not to permit the publication of details in regard to many of its metallurgical processes. This led to similar action on the part of some of its competitors. The result, of course, was a decided decrease in the number of papers written upon the practical side of the subject. Even upon the theoretical side the contributions have been few. It would seem that the industry as a whole has suffered from this general unwillingness to exchange information. While it is true that a given company is entitled to the reward that may come from its own development of a new process, it is also true that a still greater reward might be the result of a free exchange of ideas with other plants. This principle has been recognized for a long time in other metallurgical industries, notably those engaged in the smelting of iron and the manufacture of steel. It is pleasing to note that the leading lead-smelting company has very recently decided to modify its policy of secrecy, and to permit the publication of papers covering some details of its metallurgical methods. The statement has been made that there has been but little progress in lead smelting during the period just referred to. This impression is due in part to the scarcity of papers written on the subject. There has been, it is true, some discussion of the new sintering processes, but with little reference to detail, and to the effect that blast roasting has had upon the industry as a whole. In spite of the prevailing belief, it may be said that lead smelting, in common with other metallurgical industries, has made steady and substantial progress. It is the purpose of the present paper to discuss briefly some features of the industry as it is now conducted, with special reference to the blast-furnace practice in the larger silver-lead smelting plants of the United States and Mexico.

Jan 7, 1914

By H. P. Greenwald

Cooperation between the Bureau of Mines of the United States Department of the Interior and the Safety in Mines Research Board of Great Britain dates from 1924. It has been intimate and has involved exchange of personnel and. equipment as well as information. Correlation of divergent results obtained in large-scale tests of the explosibility3/ of coal dusts made in the respective countries was one of the first problems to be studied. The purpose of this paper is to show to what extent such correlation has been achieved. COMPARISON OF TEST METHODS The first research accomplished Jointly by the two organizations was a comparison of large-scale methods of determining the explosibility of coal dust. Large samples of coal were exchanged and subjected to test in the Bureau's Experimental coal mine and in the Board's steel gallery, 38 inches

Jan 1, 1939