Search Documents

By I. Hilerio

Chromium Nitride (CrN) thin films were deposited on AISI steel 316 substrates by means of the reactive magnetron sputtering method. CrN films were produced under two different conditions. In the first one, the substrate was heated by a DC source. For the second coating a negative substrate bias voltage was applied. X ray diffraction, quantitative energy dispersion and scanning electron microscope were employed to characterize the two different phases, their chemical composition as well as their microstructure. In addition, a microhardness test was carried out. The results show that a better phase formation of CrN thin films was achieved when a heating source was present (first case). Both coatings presented homogeneous surface. Their compositions show differences even when the gases flowing are the same in composition. Regarding to the hardness test results, there can be found a higher value when using a heating source.

Jan 1, 2009

By Jing Lin, Yuan Xu, Qingcai Liu, Dengfu Cheng

"Smelting reduction technology has been developed greatly in recent years. But one of the key problems for this technology is about the refractory that used as lining material in the molten bath. Investigation and test shown that corrosion rate of refractory was much higher and the corrosion mechanism was much more complexity in the molten bath of smelting reduction with iron bath than that of the blast furnace and rotary furnace technology [l-5]. The corrosion behavior and corrosion rate of Al2OrC-ZrO2 series refractory in the melt of smelting reduction with iron bath have been studied by rotary immersion and quasi-static immersion test in this paper. The major factors that affect the interaction between the melt and refractory were investigated. The test results shown that the corrosion rate of AI2O 3-C-ZrO2 series refractory decreased with the ZrO2 increasing when ZrO2 content was from 3% to 10%. Ferrous oxides content, relative moving speed between the melt and refractory and temperature of the molten bath were the important factors that affect the corrosion rate. But the ferrous oxides concentration was the most important one. The corrosion rate was increased as a linear relation with the rising of ferrous oxides content of the melt. The corrosion rate in the quasi-static immersion was much less than that of the dynamic immersion (rotary immersion) for the Al2O 3-CZrO2 series refractory in the same testing condition. The corrosion mechanism of Al2OrC-ZrO2 series refractory is: graphite oxidized in advance, then interaction between the constituents of refractory and melt taken place and deteriorate layer of refractory and new compounds were formed, the properties of refractory was changed.IntroductionSmelting reduction with iron bath is a typical technology [3, 4, 6]. The obvious features of the melt for smelting reduction technology with iron bath are much higher ferrous oxides and much more complexity melt composition and structure than that of the blast furnace technology [2, 5-8]. The properties of the melt were changed dynamicilly and constantly in reduction process. On the other hand, the behavior of the melt depends on the activity and the reduction rate of ferrous oxides in the molten bath[9]. Because of the high concentration of ferrous oxides in slag and high reduction rate in the molten bath, the corrosion behavior and corrosion mechanism of the refractory lining by melt are an important factor in development of the technology of smelting reduction with iron bath. Up to now, improving refractory quality to anti-corrosion of melt and developing high quality and long term refractory used as the lining refractory materials in the molten bath of the final reduction furnace are also the most important questions for developing smelting reduction technology."

Jan 1, 2000

By Thomas M. Harris

To avoid the escalating cost of disposal of metals-containing wastewater and residues, new wastewater treatments will focus on the recovery of the metals. A combination of ion exchange and electrowinning can produce water suitable for discharge and relatively pure metals. The use of a chelating resin can enhance the selectivity of both the removal process and the elution of metals from the resin. A new, simple method of preparing a variety of chelating resins is being developed. The materials produced by this method exhibit interesting, as well as potentially useful, elution behavior. The performance of one test resin is described.

Jan 1, 1992

By Adrien Antenen, Didier Villette

CITRON has developed a new process for the recycling of hydroxide sludge, household batteries, catalysts, automobile shredding residues, grinding sludge and other metal containing organic and inorganic waste. A pilot plant with a capacity of 1,000 tons per year has started operations in April 1998. In August 1999, an industrial plant became operational with an initial treatment capacity of 23,000 tons.

Jan 1, 2000

By R. Leiby

Prior to March 1992, the only component of the lead acid battery that was not recycled by East Penn Manufacturing Company was the sulfuric acid electrolyte. This acid was unusable in new batteries because the iron level was found to exceed new product specifications. The development of a liquid ion exchange process to remove the iron from the acid allows East Penn to currently recover over three million gallons of sulfuric acid annually. The process is based upon the use of an iron selective liquid ion exchange material or solvent to extract iron from the sulfuric acid electrolyte followed by regeneration of the solvent. Equilibrium and kinetic data for the extraction and regeneration steps were collected in order to scale up the process to commercial scale. An electrochemical process for the treatment of the acid used in the regeneration step was, also developed which significantly reduces the volume of strip acid required in the process.

Jan 1, 1995

By Ma Lijuan, Zhang Yubing, Wang Bo, Sun Huilan

The effect of lime ratio on phase composition and alumina leaching property of MgO-contained calcium aluminate clinker were investigated by analytical reagent, the XRD analysis of its mechanism was discussed. The results showed that: when the sintering temperature was 1350 ℃, C/A was 1.4, A/S was 1.3 and the content of MgO was 4%, the increase of the C/A promoted the formation of C12A7 and restrained the formation of Q-phase. The alumina-leaching ratio of the clinker (A/S was 1.3) was increased from 74.33% to 91.34% when the content of CaO was 5.21%.

Jan 1, 2015

By M. Potesser

In the primary and secondary copper industry the anode furnace is the most important process step in the refining procedure to reach an enhancement in value and quality of the copper by a selective oxidation and reduction. By combining the advantages of the conventional tilting hearth anode furnace and the benefits of the drum type anode furnace a new aggregate was developed and patented. The cross-section of the furnace is elliptical and the whole unit is tiltable. During the melting period, the contact surface between the burners and the bath or the scarp is enlarged - an increased energy input is the consequence. For the refining period the furnace is rotated, whereby a high bath level is guaranteed. Due to the longer residence time of the gas in the copper melt, not only the gas consumption is reduced but also the efficiency/quality of the refining process is improved. This investigation shows a metallurgical comparison between the new anode furnace concept with the elliptical profile/cross section and the conventional, tiltable hearth anode furnace as well as the drum type anode furnace. The CFD modeling of the currents in these different furnaces delivered helpful data to compare the geometry of the different furnaces. The investigation covered the refining of blister copper from primary metallurgy, from secondary metallurgy as well as from a mixture of both copper melts. The paper underlines the possibilities for a reduction of the tap-to-tap time and for an increase in production capacity, which can be achieved by applying the new furnace concept in comparison to the conventional furnaces.

Jan 1, 2006

By B. Ozturk, K. Ito, R. J. Fruehan

"A simulation model for bath smelting processes for the production of iron was developed which predicts the coal, flux, ore, and oxygen consumptions and the off gas volume, temperature and composition. The model is comprehensive in that it takes into account all of the important variables including coal composition, metal composition, ore composition, slag basicity, post combustion ratio, (PCR), prereduction degree (PRO), heat transfer coefficient (HTC) , flux, scrap charge, and heat losses. Four basic cases were considered: I. 30% PRO-50% PCR; II. 90% PRO-O% PCR; III. 60% PRO-30% PCR; and IV. 0% PRO-50% PCR. Several different coals were considered and a sensitivity analysis of the critical variables was performed. The model also estimates the sulfur content of the metal. The major conclusions included:1. Post combustion significantly reduces coal consumption but above 20% PCR little reduction of FeO to Fe can be performed with the off gas.2. Prereducing to FeO (Case I) and having as much post combustion as consistent with good heat transfer is an attractive process. This process only requires a simple pre reducer, uses less coal, and is relatively insensitive to the type of coal used.3. High off gas temperatures may pose a potential problem. The off gas temperature can be reduced by using an 02-Air mixture for post combustion, limiting post combustion or adding water to the gas.4. The use of CaC03 in place of CaO or of supplemental electricity does not appear attractive.5. The melting unit is theoretically an energy efficient scrap melter. For Case I using 200 kg of scrap as part of the charge the coal consumption decreases by about 80 kg.6. With PCR > 30% the FeO content of the slag is expected to be 2-5%, and the metal will not be saturated with carbon. These factors and the increased sulfur load since coal is the fuel indicate the sulfur content of the metal may exceed 0.25%"

Jan 1, 1988

By Wenya Du, Qingbo Yu, Peng Li, Qin Qin

"A new heat recovery system is proposed. This system uses the endothermic heat of gasification reaction instead of sensible heat to recover the energy of molten blast furnace slag. The gasification technological parameter in molten blast furnace was calculated and the exergy of the system was analyzed. The gasification reactions were studied kinetically by the isothermal thermogravimetry using STA409PC thermal analyzer. The results showed that, according to different gasification agent, this system can produce syngas with different C-H ratio. The exergy efficiency of this system is high and its internal exergy loss rate is about 11%. This method can bring huge economic and environmental benefits which are important to the survival and sustainable development of iron-steel enterprises. The molten BF slag acts as not only thermal media but also good catalyst. The kinetic parameters on gasification reaction with different types of coal used differ from each other.IntroductionEnergy consumption in the iron-making process is about 50%~60% of the total energy input. The blast furnace is very important in the iron & steel process. So energy conservation and emission reduction about blast furnace is very important. In recent years, in order to recovery energy, many new technologies such as TRT (Top gas pressure Recovery Turbine) and CCPP (Combined Cycle Power Plant) were used in iron-making. But the energy of molten blast furnace (BF) slag has only been used limitedly so far.Molten BF (Blast Furnace) slag is the byproduct of iron-making at the high temperatures range from 1723 to 1923K, and has a large amount of sensible heat remaining. The yield of molten BF slag is about 300 kg per ton of pig iron. In conventional processes, molten BF slag is quenched rapidly using a large amount of water to produce a glassy-granulated slag. The quenching slag must be dried before it can be used in cement manufacture. During the process, a large amount of water was consumed and the energy of molten slag can not be recovered. At the same time, it causes environmental pollution problems. So the critical problems of the process are not only energy recovery of molten slag and reducing emission of H2S and SO2, but also guaranteeing the subsequent use value of slag. For this propose, many new technologies were investigated to recover the thermal energy of molten slag. The promising methods are dry granulation [1-4] and reforming of methane [5-9]. The method, utilization of reaction heat instead of latent heat and sensible heat, is quite attractive from viewpoints of energy storage without heat loss, and makes a connection to other industry. But both of them are in laboratory. In this paper, coal gasification in molten BF slag was used to recover the energy of molten BF slag. The gasification technological parameter in molten BF was calculated and the exergy of the system was analyzed. The gasification reactions were studied kinetically by the isothermal thermogravimetry using STA409PC thermal analyzer."

Jan 1, 2011

By Satu Strömberg

Four different nickel concentrates were oxidized in a laboratory scale laminar flow furnace in simulated flash smelting conditions. The major nickel- and iron-bearing minerals in the con- centrates were pentlandite, violarite, gersdorffite, and pyrite and pyrrhotite, respectively. Thermal decomposition, ignition and oxidation behavior of nickel and iron sulfides were examined by using optical and scanning electron microscopy. General reactivity of the concentrates was monitored with sulfur removal which was most effective in violarite-based concentrate. Pentlandite-concentrates needed higher experimental temperatures for complete desulfurization and gersdorffite-based concentrate contained 5 - 10 % of the original sulfur even in the most oxidizing conditions studied (1 100°C, 50 vol-% 02). The reactivity of the iron minerals was found to depend on the other minerals present in the concentrate. In this paper, the observed re- action products and mineralogical changes are presented and preliminary conclusions of possible reaction mechanisms of nickel-bearing minerals are discussed.

Jan 1, 1997

By Ling-yun Yi, Yuan-bo Zhang, Bing Hu, Zhu-Cheng Huang, Zhen-yuan Liao

"Nucleation and growth mechanism of iron crystal grain in coal-based shaft furnace direct reduction process by microwave heating were investigated by optical microscope, scanning electron microscope and EDX. The results indicate that microwave has selectivity on various minerals which absorb microwaves. The high temperature in certain area of pellets and thermal stress on the interface of minerals are formed, results in the wustite grain smashed along the joints, and iron crystal grains turned out a spherical shape obviously. The iron crystal nucleus is formed firstly at the edge of wustite, on the interface between grains and in the holes in pellets, and grows gradually while reduction carries on from surface layer to inner core. Microwave heating promotes the rate of transportation and accumulation of the iron crystal grain, increases growth rate of iron crystal grain and contributes to formation of dense iron-jointed crystal texture eventually.IntroductionMicrowave energy as a new energy, which selectively heating materials through internal energy dissipation, has the advantages of heating uniformity, high thermal efficiency, fast heating, clean and pollution-free compared to conventional heating motheds. Microwave energy also has obvious superiority in increasing productivity. Thus, it has been widely used in many areas, including electronics, food processing, chemical, medicine, environmental protection, and family life etc [1]. As a rapidly developed green metallurgical method, microwave heating also has been widely recognized by areas of grinding, pretreatment, pre-reduction, drying, furnacing, metal extraction, and waste materials processing and utilization. Some research achievements are gradually putting into practice, showing great potential in chemical and metallurgical industry [2-3]."

Jan 1, 2011

By H. Kung, T. R. Jervis, M. Nastasi, T. E. Mitchell

"A systematic study of the structure-mechanical properties relationship is reported for nanolayered composites of MoSh-SiC, Mo-MoSh, Mo-MoShNx, MoSi2-MoSi2Nx, and Mo-MoShMoSi2Nx (x=3-4) synthesised by sputtering techniques. These composites have been studied by nano-indentation and cross-sectional TEM as a function of annealing temperature. As-deposited layers are amorphous except for Mo. With increasing annealing temperature, first MoSh and then SiC crystallize, while the hardness progressively increases until the layers start to spheroidize and grain growth sets in at 900ºC. For the case of Mo-MoSi2, the layers react and the composite deteriorates rapidly. However, MoSi2Nx remains amorphous up to 1000ºC, suggesting that it could act as a diffusion barrier between Mo and MoSi2. In fact the Mo. MoSi2Nx, MoSi2-MoSi2Nx and Mo-MoSi2-MoSi2Nx nanolayers are found to remain stable up to such temperatures. IntroductionMolybdenum dislicide, MoSh, is a potential matrix material for high temperature structural composites due to its high melting point and good oxidation resistance at elevated temperature [1]. The two major drawbacks for structural applications are inadequate high temperature strength and poor low temperature ductility. Silicon Carbide (SiC) being hard and thermally compatible with most ceramics and intermetallic compounds, has been found to be suitable for second phase reinforcement in various structural applications and, in particular, the addition of SiC whiskers improves the high temperature yield strength of MoSi2 [2]. While most of the research in MoSb-SiC composites has been on the particulate form of SiC, laminated composites may offer unique properties. It has been shown that synthetic multilayers with alternating layers of metal and/or compounds may exhibit interesting mechanical properties [3]. Enhancement in mechanical properties by decreasing the wavelength of multilayer spacing has been studied extensively. In general, two types of strengthening have been proposed: (1) Hall-Petch strengthening [4,5], where the strength increase is inversely proportional to the square root of the layer thickness; (2) Koehler modulus strengthening [6], which increases with modulus difference and decreasing layer thickness. In the present study, we have performed a systematic study of the relationship between strength and structure in a number of different nanolayered systems based on MoSh. Layer thicknesses have been varied and their nanostructures have been varied by heat treatment. Previous work on MoSi2-SiC is summarized [7]. In an attempt to improve fracture toughness, MoSh-Mo nanolayered materials have been prepared but are found to react and deteriorate. Previous work has shown that nitrided MoSi2 (MoSi2Nx with x=3-4) is highly stable [8] and so nanolayered composites of MoSi2-MoSi2Nx and Mo-MoSi2-MoSi2Nx have been prepared to assess the' stability and mechanical properties of these composites. Preliminary results are presented."

Jan 1, 1994

By Michael J. McGuire

Rostoker, Inc. has developed a process to smelt solid hazardous/non-hazardous inorganic wastes. Near seven hundred experiments were performed. Actual industrial wastes as well as reagent grade chemicals were used. By mixing a multiplicity of these wastes to proper formulations, then furnacing them, it was determined that saleable end products could be reclaimed; metal, fume and slag. The slag, due to its siliceous structure was tested to be leach resistant (40 CFR). This formed the essence of our patent, #5,180,421 "Method and Apparatus for Recovering Useful Products from Waste Streams". What is unique is that a HTMR (High Temperature Metal Recovery) process has been developed that can treat a multiplicity of wastes within the same furnace. The discussion will include a list of waste streams we have treated, details of proper waste formulation and experimental results.

Jan 1, 1994

By N. Shi, T. C. Lowe, S. J. Zhou, M. L. Lovato, Y. T. Zhu, J. A. Valdez, W. R. Blumenthal, M. G. Stout

"A major problem of short-fiber composites is that the interfaces between the fiber and matrix become a limiting factor in improving mechanical properties such as strength. For a short fiber, a strong interface is desired to effectively transfer load from matrix to fiber, thus reducing the ineffective fiber length. However, a strong interface will make it difficult to relieve fiber stress concentration in front of an approaching crack. Stress concentrations result in fiber breakage. We report in this paper an innovative approach to overcome this problem: reinforcement morphology design. Short-fibers with enlarged ends are processed and used to reinforce a polyester matrix. The initial results show that the bone-shaped short-fibers produce a composite with significantly higher strength than can be attained with conventional short, straight fibers.IntroductionThese interfaces between the fiber and the matrix in short-fiber composites play a critical role and, in many cases, become a limiting factor in improving such mechanical properties as strength and toughness of the composites (1-4). For a short fiber, a strong interface is desired to effectively transfer load from matrix to fiber. A stronger interface can reduce the ineffective length at both ends of the fiber and, therefore, can increase the effective length that carries load (5-9). However, with a strong interface it is difficult to relieve fiber stress concentration -in front of an approaching crack; and such stress concentration can result in fiber breakage (10, 11). This effect is particularly severe for ceramic matrix composites, because of their low matrix toughness and lack of plasticity. Even for a composite with a highly ductile matrix, such as plastics, too strong an interface may still cause successive adjacent fiber breakage and subsequently reduce composite toughness (1, 11). On the other hand, a weak interface significantly decreases the fiber load-carrying length due to ineffective load transfer and complete fiber interfacial debonding and pullout during loading. A compromise in the interfacial bond strength will also compromise the load-carrying potential of short fibers."

Jan 1, 1998

By Carlos Ortiz

The Huelva Flash Smelting Furnace was commissioned in September 1975. The Smelter and the Acid Plant were expanded in 1995 to their present capacity of 300,000 tpa new copper equivalent and one million tonnes of concentrate per year. During these years of operational experience, most of the initial practices have been reviewed, process control has drastically improved and main process equipment has been modernised. The fourth Flash Furnace campaign lasted 9 years (1995-2004) during which 8 million tonnes of concentrate were smelted. Increasing sulphur content in concentrates and new environmental requirements imply new challenges for smelters to keep production and operation costs down. This paper is an overview of the modifications and improvements carried out in the 2007 general shutdown in Smelter and Acid Plants. Al

Jan 1, 2008

By M. El Ganaoui, P. Bontoux

"A computational model to investigate solid/liquid phase change transitions for binary alloy under directional solidification is presented. Conservation equations are developed by using an homogeneous formulation. A second order accuracy method of time and space based on finite volume approximation has been evaluated by comparing results to spectral solution for time-dependent solutal convection developping in a melted alloy. For extended model to solid/liquid interface effects time amplification of solutal perturbation injected near the interface is described before considering solutal convection is melt.IntroductionThe enthalpy method gives a front fixing approach for energy equation without introducing coordinate transformation. The interfare position is recovered a posteriori [1]. A number of authors have extended this approach so as to include the convection phenomena within the two phase 'mushy region' [2, 3, 4, 5, 6].We have developed a time-dependent enthalpy-porosity formulation for directional solidification [4, 6, 8]. The interaction between solid and liquid phases is modelised by a Darcien type force in the phase change area. The behaviour of the melt is similar with the flow of an incompressible fluid in a porous medium. This force is proportional to the relative phase velocity. It corresponds to a damping force depending on the anisotropic permeability of the 'mushy zone'. The permeability depends on the liquid fraction and on the size of·solidification microstructures. An informative discussion of a new slant on the general approach of continuum mechanics needed to analyze the formation of mushy zone is given in [12]. The method is extended to the presence of species diffusion: the solutal Stefan condition which expresses the solute incorporation or rejection across the interface is accounted implicitly in a species equation valid in all the domain [14, 15]."

Jan 1, 2001

By K. Krishnapisharody

The phenomenon of slag droplet formation under the action of gas-stirring in steel ladles has been analyzed with experiments conducted in a thin-slice room-temperature model using water and mineral oils as the working fluids. Visual and video investigations have been performed on the interface behaviour along with measurements of liquid velocities in both phases, using the Particle Image Velocimetry (PIV) technique. The measured velocity data and observations on the interface break-up establish that the droplet formation results primarily from an instability mechanism at the interface.

Jan 1, 2008

By I. Gaballah

Cadmium is toxic to plant, animals and humans. The council directive of the European Communities No 8315 13lEEC has fixed an upper limit of 200 ppb for the release of cadmium in industrial effluents. The conventional method of neutralization/prccipitation ( NIP ) is inefficient to reach this limit. The objective of this study is to test the efficiency of the trees modified bark to remove cadmium cations from industrial effluents after the conventional treatment by NIP. Laboratory scale tests with synthetic solutions show that the cadmium removal depends upon pH and initial concentration. About 99.9 %, 99 % and 96 % of the metal are removed from synthetic solutions containing 10, 100 and 1000 ppm respectively. Pilot plant trials ( 1 m3 ) with an industrial effluent bearing about 500 ppb of cadmium lead to the almost complete elimination of the cadmium ( final concentration is lower than the analytical detection limits < 20 ppb ).

Jan 1, 1994

By Guillermo Rios, Arbizum Cristina, Joa Viflals, Alba Sunyer

"Atlantic Copper is one of the largest copper producers in Europe. Its production facilities are located in Huelva (Spain) and account for the smelting of over one million tpy of concentrates to produce up to 260 ktpy cathodes and 900 ktpy of sulphuric acid. During copper concentrate smelting, the slag coming from the flash furnace and PS converters are treated in an electrical slag cleaning furnace. As a result of the treatment of the off gases from this furnace, approximately 2,000 tpy of a Zn-rich filter cake are produced and are sent to authorized waste managers. This paper describes the characterization of this material and the preliminary results of a new process to recover zinc as a pure zinc hydroxycarbonate while lead is collected as an indium-rich anglesite product. The behavior of impurities (Cd, As, Tl, Sn, Sb, Bi, Cu, Se, Te) in the leaching, solution purification and precipitation steps is also reported.IntroductionThe Atlantic Copper Metallurgical Complex in Huelva (Spain) was commissioned in 1970 with a capacity of 40,000 tpy of copper from concentrate. In 1975, the old blast furnaces were replaced by Outokumpu flash smelting furnace (FSF) technology, and the copper refinery capacity was increased to 108,000 tpy. Between 1994 and 1996, an expansion project was carried out to increase the copper from concentrate and cathodes to 250,000 tpy and 215,000 tpy, respectively. This expansion basically consisted of a new sulphuric acid plant, replacement of the anode furnaces by two 400 t units, redesign of the slag cleaning furnace (SCF), an increase in the electrolytic cells to 1,120 and implementation of ISA permanent cathode technology. Furthermore, a debottlenecking project has led to a capacity of 1,000,000 tpy of fresh concentrate since 1997. Meanwhile between 1995 and 1998, a cathode production rate of 260,000 tpy was reached as a result of a progressive increase in the current density in the refinery."

Jan 1, 2012

By D. B. Dreisinger

The zinc pressure leach process developed by Sherritt Gordon, Ltd. permits the direct leaching of sulphide concentrates according to the overall reaction, ZnS +H,zS04 +402.+ZnS04+H20 +S0 The kinetics of the leach are affected by three rate controlling steps; ( l) oxygen mass transfer from the gas to the leach solution, (2) homogeneous oxidation of ferric ion to ferric ion by dissolved 011.ygen and (3) ferric ion leaching of zinc sulphide in the presence of a sulphur dispersing detergent (lignin sulphonic acid). Fundamental studies have been conducted to identify the factors that influence the kinetics of each individual rate controlling step. Oxygen mass transfer studies have been directed toward optimization of the agitator configuration for solids mixing and gas pumping from the atmosphere above the leach slurry. The rate of ferrous oxidation by molecular oxygen and the rate of zinc sulphide leaching by ferric ion have been studied over a wide range of temperature and solution compositions. The study of zinc sulphide leaching by ferric ion was supplemented by a series of interfacial tension measurements in the liquid sulphur - zinc sulphate solution system. The various kinetic studies have been summarized in terms of the importance of each rate to the performance of the process.

Jan 1, 1990