Search Documents

By Fu-Shen Zhang, Mengjun Chen, Jianxin Zhu

"In the present study, different types of cathode ray tube (CRT) glasses were examined by sequential extraction combined with TCLP to provide possible explanations for how Pb and Ba leach out from the waste CRT glasses and to give possible reasons for why they leach out. Sequential extraction results showed that Pb and Ba in the CRT glasses dominanfly presented as the residual fraction. The exchangeable fractions of Pb and Ba were extremely low, less than 0.01 % of the total content, but they were higher than those required by the regulation limits, 5 and 100 mg/L for Pb and Ba, respectively. TCLP tests of the original CRT glasses and CRT glasses residues after each step of sequential extraction demonstrated that the extremely high leaching toxicity of CRT glasses mainly caused by its exchangeable and carbonate fractions of Pb and Ba.IntroductionIn recent years, the amount of cathode ray tube (CRT) contained monitors or TV sets in the market were sharply reduced, since they were substituted by novel and better electronic and electric equipments such as LCD and PDP, leaving huge amount of end-of-life CRTs. 50-85% of the total weight of this kind of computer monitor or a TV set is glass[1,2], which was classified to three categories according to their chemical compositions: black & white glass (BW), color panel glass (CP) and color funnel glass (CF)[3]. In order to provide shielding from X-rays generated during the picture projection process, lead, barium and strontium oxides were used in the glass. In general, a color CRT contains 1.6-3.2 kg of lead . Therefore, these glasses have attracted wide and tense attention due to the potential risk to the environment and human health."

Jan 1, 2011

By K. Verbeken, E. Wettinck, M. Verhaege

Iron (III) can easily and selectively be removed from acidic sulphate solutions with organo-phosphoric acids like Di-2-Ethyl-Hexyl-Phosphoric Acid [D2EHPA]. Stripping of the iron (III) loaded organic, however, is difficult unless highly concentrated inorganic acid solutions are used. In this paper results are shown for the enhanced stripping of iron from loaded D2EHPA by electro-reduction. The loaded solvent is contacted with a 2 M H2SO4 solution, which is continuously recycled in an electrochemical reactor where iron (III) is reduced to iron(II). As iron (II) is not extracted by D2EHPA, the equilibrium for iron (III)- D2EHPA is shifted towards the aqueous iron (Il)-sulphuric acid solution. The electro-reduction unit is a vessel with separated catholyte and anolyte chambers. The catholyte is the actual stripping solution where iron (III) is reduced to iron (II) on a stainless steel electrode. The anolyte is a 2 M H2SO4 solution where oxygen is evolved on a lead alloy electrode. A sintered glass plug separates the compartments. With this unit, enhanced stripping of iron from the solvent is possible under mild acid conditions [2 M H2SO4], and a concentrated ferrous sulphate solution can be obtained. The results shown have mainly been obtained by studying the parameters affecting the electro-reductive stripping of a D2EHPA loaded organic phase in a batch reactor. From an iron (IH)-saturated 20 vol. % D2EHPA solvent containing ~ 12.5 g/1 Fe (III) over 90% of the iron can be stripped in one stage with a 2 M H2SO4 solution at 50°C. It is shown that in this way it should be possible to obtain a concentrated ferrous sulphate solution which can be processed downstream to recover a pure iron product.

Jan 1, 2000

By Carlos Eduardo Gomes de Souza, Luis G. S. Sobral, Paulo A. Medeiros da Silva, Selma G. F. Leite, Renata de B. Lima

"The use of mixed cultures of acidophilus microorganisms that act in different temperature ranges, aims at speeding up the digestion of chalcopyrite, highly refractory sulphide mineral, the major mineral in the flotation concentrate of Caraíba Mining Co., with an attractive processing cost. The concentrate under consideration contains mainly chalcopyrite (CuFeS2) and bornite (Cu5FeS4) with contents of, approximately, 70 and 30%, respectively. It was observed in this study, the performance of consortium of mesophiles, moderate and extreme thermophile microorganisms, in the oxidation of the aforementioned sulphides minerals, evaluating operational parameters such as pH of the leaching solution, the reaction temperature and redox potential, with consequent extraction of 80% of the concentrate copper content within 60 days of bioleaching. Such high copper extraction was achieved in column bioleaching tests.INTRODUCTIONThe solubilization of metals by the application of microorganisms from the mineral ores and the subsequent recovery of metals from solution are referred to as bioleaching (Rohwerder, T et al, 2003). This is an economical method for the recovery of metals from minerals; especially lowgrade ores, overburden, and waste from current mining operations which requires moderate capital investment with operating cost (Watling, 2006).Furthermore, bioleaching is generally more environmentally friendly than conventional metal recovery processes such as concentration and smelting. Those physicochemical metal extraction processes generate sulphur dioxide, a toxic emission that is increasingly the target of regulatory legislation (Stott et al., 2000; Olson et al., 2003). Bioleaching of chalcopyrite is the key industry target. The main problem hindering commercial application of chalcopyrite bioleaching is the slow dissolution rate (Fu et al, 2008).Dissolution of acid-soluble sulphide minerals such as sphalerite, and to a lesser extent chalcopyrite, occurs by a combination of ferric iron and proton attack via the polysulphide pathway (Rohwerder et al., 2003)."

Jan 1, 2008

By Dinabandhu Ghosh

The stability diagram of the ternary system Ti-C-O is drawn in the present work for four temperatures, 1473 K, 1573 K, 1673 K and 1873 K, showing the stability fields of TiC, Ti, TiO, Ti2O3 and TiO2. An analysis of the system reveals that it is not possible to produce Ti in a carbon-saturated system; instead, the stable product is TiC. However, Ti can be an equilibrium product in a carbon-unsaturated system at prohibitively low values of pCO and pCO2; for example, at 1873 K, these limiting values are: pCO = 10-6.76 atm and pCO2 = 10-13.36 atm, which, when exceeded, produce TiC and TiO respectively. The magnesiothermic reduction is examined through the stability diagram (log pO2 vs. 1/T) of the system Ti-Mg-O, drawn for a number of pMg values, presenting the pairwise stability fields such as Mg(l) + Ti(s), Mg(v) + Ti(s), MgO(s) + Ti(s), etc. The diagram shows that magnesium reduction of TiO to Ti is possible only at T < 1641 K with pMg = 1 atm and only at T < 1569 K with pMg = 0.5 atm. An experimental scheme for Mg vapor reduction of TiO2 is proposed in which an argon stream is passed over a Mg(liquid) evaporator at temperature T1 (say, 1234 K); the resulting Ar-Mg mixture at 1 atm is subsequently flown over a bed of TiO2 at temperature T2. A thermodynamic analysis establishes that complete reduction to Ti is possible and that the best results are obtained when T1 = T2.

Jan 1, 2006

By Tracy Morris, Weldon Read, Luis Navarro

"During the leaching of anodic slimes, tellurium dissolves into the leach liquor together with copper and must be removed before the solution is sent to liberator cells for copper recovery. Prior to the installation of autoclaves, tellurium was precipitated using raw slimes that caused a recirculation of tellurium in the leaching circuit. After autoclaves were installed the old leach tanks were converted into tellurium reactors utilizing copper chips, steam and agitation to form a copper telluride precipitate. Tellurium levels of less than 10 rng/L are achieved in a timely manner.IntroductionThe electrolytic refining of copper consists of an electrolytic cell provided with an anode of impure copper, a cathode of substantially pure copper (starter sheet) and an electrolyte made of copper sulfate and sulfuric acid [1]. When a direct electrical current is passed between the anode and cathode inside the cell, the impure copper anode dissolves in the electrolyte and pure copper is plated onto the cathode. During this operation, many of the impurities are deposited on the bottom of the cell as an anodic slime residue composed of insoluble chemical compounds. Slimes are a major source of rare and precious metals in the copper industry [2-5],In the Amarillo Copper Refinery (ACR), the anodic copper slimes are sent to the Precious Metals department in order to extract and then refine the gold, silver, platinum and palladium from them. The remaining impurities, in the form of a soda slag or copper slag are sent to the Hayden smelter for further processing. Copper telluride is sent to the Selenium/Tellurium department inside the plant for selenium and tellurium recovery. During the leaching process of the anodic slimes, copper, tellurium, and other metal species in the slimes are dissolved into leach liquor that cannot be returned to the tankhouse unless the tellurium concentration is below 10 mg/L."

Jan 1, 2012

By José Sancho, Julia Ayala, Purificación García, Begoña Fernández

"A study is carried out to see the adequacy of using flying ashes coming out from a Power Station to eliminate the copper present in waste cyanide waters that are generated in gold mines.Tests were carried out to see how effective the use of ashes taken from two Power Stations could become. Later, the tests are made using ashes coming from Narcea Power Station as this station is near the mine under study.The work is centred on looking for an economically adequate solution to close the waste decanting ponds of the mine. After several tests, a solution is reached through filtration in static layers.IntroductionThe use of coal to adsorb some water-soluble substances has been widely studied [1,2,3,4,] both in the treatment of drinking waters and in determined stages of selective detachment of cyanide gold complexes in cyanide lixiviation processes [5]. Flying ashes sent to the atmosphere by Power Stations as a sub-product of the combustion of this combustible are generally made of more of a 70 % of a vitreous aluminosilicated material and of an active residual material which may be changeable making them potentially useable as adsorbents. Nevertheless, the properties of each kind of ashes depend on the characteristics of the Power Station, of the combustibles being used, of the combustion system, etc.The aim of this work is to demonstrate the adequacy of flying ashes to eliminate the copper present in cyanide waters coming from gold mines either by adsorption or precipitation of the metal. For this study, tests are carried out with Asturian ashes which have a low quantity of lime. The results obtained in the tests demonstrate the effectivity of the method used. To be absolutely concrete, the work is carried out to establish the use of these ashes in the closing of Asturian installations of cyanide lixiviation"

Jan 1, 2008

By Cristiän Vargas, Jaime Simpson, Gerardo Cifuentes

"This paper presents a new process for the precipitation of Sb and Bi present in copper refinery electrolytes in the presence of Pb02 (Chilean Patent No. 45,037). To establish the conditions under which the precipitating compounds form, it was necessary to evaluate the amount of PbCh consumed, antimony extraction efficiency, precipitate stability, reaction kinetics, diffraction analysis and X-ray fluorescence, separation of size, plus observation of the precipitates in the electron microscope. Preliminary tests were carried with synthetic copper refinery electrolyte, and then the final testing was done with electrolytes from Chilean refineries. This process provides a real alternative for the treatment of copper refinery electrolytes for the control of Sb and Bi in solution; it is very simple to operate and is low cost compared with competing processes.Introduction.A high quality copper cathode implies a cathode free of impurities. The electrorefining process seeks to eliminate these impurities from the copper anode (99.5% purity) by its dissolution in an acid electrolyte using chemical and electrochemical reactions. As a result of this process, a cathode (99.99% purity) is obtained. If the concentration of impurities in the electrolyte, from the dissolved anodes, begins to increase; particularly if the antimony concentration in the electrolyte increases up 500 ppm, the formation of floating slimes which are a major cause of contamination of the cathode is favoured. The most important impurities from the point of view of their effect on the quality of the cathode copper, are Ag, As, Sb, Bi, Pb, Se and Te. Silver is necessary for the control of Se and Te. To control all of these impurities, it is necessary to establish different methods or parameters of control in copper electrorefining. These parameters are anode composition, additives, purification of the electrolyte, current density, acidity, etc."

Jan 1, 2012

By Thomas J. O'Keefe, Pu Yu, George Houlachi, Xuewen Tang

"Impedance measurements were used to investigate the electrochemical characteristics of acidic zinc sulphate electrolytes containing Sb3+, gelatin and their mixtures. The data were correlated with cyclic voltammetry curves made using synthetic as well as industrial electrolytes. The cyclic voltammetry results were similar to those obtained in previous studies in that antimony caused a depolarizing effect while gelatin gave an increase in the potential for zinc nucleation on an aluminum substrate.The electrochemical impedance spectroscopy (ElS) evaluations were conducted on electrodeposited zinc at three overpotential values. The potentials were chosen to represent various current density regions in the zinc polarization curves. The antimony and gelatin gave characteristic impedance plots which correlated with expected behavior, particularly current efficiency. Both antimony and glue appear to modify the intermediate zinc reaction sequence, but in different ways. The data strongly suggest that film formation and stability are major factors in the zinc ion reduction mechanism.IntroductionThe zinc electrodeposition process is sensitive to the presence of a variety of organic and inorganic chemical species in the electrolyte [I]. Such components can produce either beneficial or harmful effects, depending on their relative concentrations and electrochemical behavior. Extensive investigations have been made to gain a better understanding of the changes occurring during zinc deposition in the presence of such additives. Techniques employed include microscopy, x-ray diffraction, dynamic voitammetry, current imd energy efficiency studies [2-5]. Ultimately, the objectives are to identify the factors which most affect the efficiency of the process and to provide a means to effectively control them.One of the most harmful impurities is antimony, which can be detrimental when present at concentrations as low as 10 to 20 parts per billion. Dramatic changes in zinc polarization behavior, deposition structure and current efficiency have been observed with antimony in the electrolyte. Antimony appears to lower the hydrogen overpotential by hydride formation or a similar catalytic mechanism, which allows an increase in localized corrosion and zinc dissolution [6-8]."

Jan 1, 1997

By Jian Pan, Zhen He, Deqing Zhu, Shouyan Yue

"The differences of raw material characteristic among six kind of iron concentrates and the influences on ballability were studied from the aspect of the size distribution, specific surface area and particles morphology. The results show that the specific surface area of iron concentrates has crucial influence on ballability, and the effective method of improving ballability for weak ballability iron concentrate has been found. It is of important guidance for Chinese steel mills to import and use iron concentrate from the whole world.IntroductionChina's steel industry has developed rapidly in recent years, crude steel production in 2011 is an unprecedented 683 million tons, which is almost half of the world crude steel production, and it is equivalent to the total sum production of the nations which rank at 2,3,4,5 and 6 in the world [1]. In order to match the development of steel industry, the blast furnaces are becoming larger and more modernization, therefore charging burden of higher quality is requested, and the reasonable blast furnace burden structure is more and more important, at the same time, for iron ore powder sintering process's continuous improvement and development, another method providing ""concentrate"" for blast fumace-pelletizing is also taken seriously. The grate-kiln method of pelletizing has achieved great development for its unique advantage, and in just a few years, there are over 60 rotary kiln production lines have built or being built in China, the sum of pellets has reached to more than 140 million [2, 3]. The rapidly growth of pelletizing yield demands diverse source of pellet, which include not only domestic magnetite concentrate, but also imported hematite which is high in iron and low in silicon. Usually the ratio of imported hematite concentrate increased gradually. The imported hematite concentrate has high grade and fine particle size (the content of -0.074 mm mostly higher than 90%), but the ballability of part of the concentrates is poor."

Jan 1, 2013

By E. Kuzeci, R. Kammel

"Lately various voltametric methods have gained increased attention as an analytic tool in hydrometallurgy. Voltammograms with mercury drop electrodes or glassy carbon electrodes provide information about the electrocrystallization of cathodic deposits and allow calculation of kinetic data by means of characteristic parameters like the peak potential and peak current and their variation with the voltage scanning rate.Cyclic voltammograms are also suitable for identification of reaction sequences. Voltammograms with carbon paste electroactive electrodes containing metal sulphide additions reveal information about the dissolution behavior. The stripping voltammetry can be applied to analyze metal ions and organic additives (e. g., thiourea) in extreme low concentration. Typical application of the various methods studied with microcomputer controlled measurement system are explained by examples selected from copper hydrometallurgy.IntroductionThe use of electroanalytical methods in metallurgical process control can be dated back to the starting period of industrial copper refining, when the deposition of the metal ions was followed electro-gravimetrically by weighing the electrode with deposits (1). The principles of metal deposition and dissolution have not changed but the methods to follow these phenomena were subjected to noticeable developments and especially the introduction of polarographic investigations by Heyrowsky (2) has greatly contributed to the progress in electro-analysis. A review about the fundamental work on the electrochemical kinetics in earlier time is compiled in a monograph of Vetter (2). With the steady improvements in the instrumental techniques, it is nowadays possible to apply several current and potential modulations for measurements with improved selectivity and sensibility. There is however, still a lack in theoretical interpretation of the data obtained. More theoretical information are already available for linear voltametric methods for systems where reduced as well as oxidized species are dissolved in the electrolyte (4, 5). Some recent investigations have also shown the reliability of these techniques to study electro-crystallization (6, 7). Main fields of the application in the hydro - and electro-metallurgy are:"

Jan 1, 1989

By Batric Pesic

A hydrometallurgical process for recovery of Zn and Mn from Bunker Hill Water Treatment Plant sludge was developed. The process is unique because it treats an unusual combination of metals, Zn and Mn. Another non-standard feature of the process is that leaching takes place with ~S04 in the presence of a reductant (SO2). Zn and Mn are recovered simultaneously by electrowinning, Zn on a cathode and Mn on an anode, as MnO2 The major purpose of the process is to detoxify the sludge by removing toxic heavy metals. The recovered metal values could be marketed to offset the overall costs of water and sludge processing. This work is presented in two separate parts, 1. Leaching and Solution Purification, and II. Electrowinning. This paper covers only the first part of the hydrometallurgical process: Leaching and Solution Purification. Initially, the paper briefly discusses the history of the pollution problem at the Bunker Hill Superfund Site, the origin of heavy metals in the mine waters, and the development and use of the water treatment plant. The leaching of sludge was examined as a function of the following parameters: constant vs. initial pH, initial vs. delayed addition of SO2, temperature, and pulp density. It was found that leaching with H2SO4 at pH 2.0 for 15 minutes (at 60°C), followed by S02 addition for another 15 minutes, could completely dissolve Zn and Mn. Solution purifIcation was done in three stages. In the first stage iron was removed by adjustment of pH (to pH 5.0) and oxidation offerrous to ferric iron (with H2O2). In the second stage, Cu and Cd were removed by Zn dust cementation. Finally, Co and Ni were precipitated with the organic reagents 1-2 nitroso-naphthol and nitroso, respectively. Electrowinning of Zn and Mn is discussed separately in Part II of this paper.

Jan 1, 1996

By Ragnhild E. Aune, Shahid Akhtar, Reza Beheshti

"The potential use of Black Dross (BD) as a raw material for the production of refractories, fluxing agents and glasses is the main motivation of the present study. Heat treatment experiments were carried out in Ar, and under reduced pressure (20 Pa), to evaluate the salt removal efficiency. The chemical composition of the BD after heat treatment was investigated by SEM-EDS and XRD analyses. Based on the present results, it is established that the salt starts to evaporate at ˜1273 K in Ar, and under reduced pressure. The salt removal efficiency in a 20 g sample was found to increase in both cases as a function of time and temperature. Moreover, in Ar the chlorine concentration was lowered to 0.3 wt% after heat treatment at 1523 K for 10 hours. Under reduced pressure, however, 0.2 wt% residual chlorine was obtained after 8 hours at 1473 K.IntroductionIt is believed that aluminum recycling in the near future will become the main route of aluminum production [1]. Black dross (BD) that is produced during this process contains, among other things, high amount of salts like NaCl and KCl [2, 3]. Almost 800,000 tons of BD is annually land filled in United States and this number continues to grow with the increase in aluminum recycling [2]. The BD should be dumped in controlled land field and it is costly procedure [4, 5].The water-soluble compounds in BD react with water or environmental humidity and release chlorides into the water and/or generate toxic gases such as H2, CH4, NH3 and H2 S [6-8]. In the Europe, BD is considered as toxic waste and its disposal as landfill is forbidden [8, 9]. After salt removal, the BD is considered to be non-hazardous and can be buried under ground [10].On the other hand, BD do also contains many relatively valuable compounds that may be changed in to useful materials as a result of further treatment [11, 12]"

Jan 1, 2012

By Takamasa Ishigaki, Gervais Soucy, Mohamed Rahmane

"The induction plasma jets employed for the in-flight nitridation of molybdenum disilicide (MoSi2) powders were investigated in terms of their flow characteristics. The present study shows the effect of the operating parameters of the plasma torch, as used for this process, on the plasma jet properties. The enthalpy probe techniques, along with mass spectrometry, were employed for the measurement of the jet temperature, velocity and concentration fields. The measured values were compared to the results of a numerical simulation performed on the plasma flowing inside the torch-reactor system. The process operating conditions studied were the plasma plate power, chamber pressure and sheath gas composition. The optimal conditions for effecting the nitridation process using thermal plasma are obtained at moderate plasma plate power, at around atmospheric pressure and by using a mixture of argon and nitrogen as the plasma torch sheath gas.IntroductionMolybdenum disilicide (MoSi2) based composites are considered to be one of the most promising candidates for high temperature structural material applications [!], especially because of their high melting points, good oxidation resistance and relatively low cost. However, the wide application of these composite materials is still limited by some factors such as their brittleness at room temperature and lower strength at high temperature (> 1500 K). To overcome such limitations, a number of researchers [2-4] have earlier studied various kinds of reinforcements for MoSi2, e.g. oxides, silicides and nitrides. More recently, Fan and coworkers [5-9] have demonstrated the possibility of in-flight nitridation and carburization of MoSi2, using a thermal plasma process. This work has confirmed the plasma synthesis route as one of the most promising methods for creating an in-situ second phase structure. Properties of the plasma flow, such as its temperature, flow velocity and composition, are of crucial importance for the nitridation of MoSi2 powders during their flight in the plasma. Therefore, the optimization of such a process involving plasma· generated reactive species necessitates a thorough understanding of the plasma flow characteristics."

Jan 1, 2000

By Jie Ma, Bo Wang, Jieyu Zhang, Jian Zhao, Guangxin Wu, Shunli Zhao

"Nucleation and growth model based on a 3D CAFE model, which was incorporated with macro heat transfer calculation within ProCAST software was used to predict the solidification microstructure of austenitic stainless steel in twin-roll strip casting. The simulation results of solidification microstructure agreed well with experimental results of austenitic stainless steel. The effect of different casting process parameters on the solidification microstructure was simulated. The predicted results show that solidification microstructure is obviously sensitive to superheat and convection heat transfer coefficient. With the increase of superheat, the grain density decrease and the proportion of columnar crystal increase. In addition, the proportion of columnar grains increases when convection heat transfer coefficient increases. Thus, it was demonstrated that the solidification microstructure evolution of twin-roll strip casting could be predicted reasonably by using this model.IntroductionNear-net-shape casting technology is an important research area in the iron and steel industry today. Twin-roll strip casting represents a major area of concentration of near-net-shape casting technology. It has been widely used for its outstanding advantages, such as extended solubility of alloying elements, refined solidification microstructure and reduced microsegregation [1]. Furthermore, it is the most environmentally friendly, energy saving, and C02-sensitive way to produce steel strips [2]. Therefore, much attention remains to be paid to this aspect. A lot of published works indicated that the solidification microstructure of twin-roll thin strip has obvious effect on the thin strip properties [3, 4]. For the accurate control of parameters of the process are made difficult due to the complicated process and the multi-fold factors, great attentions have been paid to numerical simulations to provide insight into the solidification behaviors of the thin strip formed by twin-roll strip casting [5, 6].Simulations of casting solidification can provide a method to predict microstructure and to improving strip quality by controlling the process parameters."

Jan 1, 2014

By Baicheng Liu, Houfa Shen, Wensheng Li

"In order to understand the formation of macrosegregation in steel ingots, a mixture model has been developed which accounts for coupled mass, momentum, species, and energy transport to describe the sedimentation of free equiaxed grains during solidification. In this model, the mushy zone is divided into the slurry and porous regimes according to a solid packing fraction. Settling velocity of equiaxed grains in the slurry regime is given by an explicit expression. The solidification of a binary steel ingot (Fe-0.36wt.%C) with a two-dimensional geometry is numerically simulated. It is demonstrated that the predicted macrosegregation patterns agree to some extent with classical experimental results. Further refinement of this model is still necessary for realistically simulating steel ingot solidification.IntroductionModeling macrosegregation in steel ingots is still a challenging study, mainly due to the length scale of the products and the complexity of global multiphase transport phenomena coupled with microscopic solidification kinetics [l]. The thermal-solutal convection and the motion of equiaxed grains are the two main mechanisms responsible for macrosegregation. But there are few models that deal with the motion of equiaxed grains, which is confirmed as the main phenomenon that explains the negative macrosegregation along the centerline of large steel ingots [2]. A model which takes into account melt convection and grain sedimentation was first proposed by Beckermann and co-workers ([3], and references therein). More recently, similar multiphase solidification models with advanced nature have been presented by Wu and Ludwig [1,4] and Combeau and co-workers [5,6]. It is known that the application of these sophisticated models to steel ingot casting is at its beginning.In this paper, a solidification model based on continuum mixture approach, using much less sophisticated relations to obtain the settling velocity of free equiaxed grains, has been proposed in order to predict the macrosegregation in steel ingots. The model is applied to simulate the solidification of a binary steel ingot with a two-dimensional geometry, and preliminary modeling results are presented."

Jan 1, 2011

By Sijun Li, Bingyu Zhang, Haitao Zhou, Zhendong Zhang, Guofei Si, Xianghua Liu

"Hot compression test of Nb microalloyed coiled tubing steel is performed on Gleeble3500 at 1123K—1373K and strain rate from 0.001 to 5s-1. It is found that flow softening occurs and the flow curves exhibit a peak with a characteristic of dynamic recrystallization (DRX) and change with temperature and strain rate significantly. The peak stress and peak strain are dependent on the Zener-Hollomon relationship with activation energy of 390 KJ/mol. On the basis of Avrami equation and the Zener-Hollomon parameter, it is obtained that the dynamic recrystallization kinetics equation with which the calculated and measured recrystallization fraction is very close. On the results of hot compression test, the Nb microalloyed coiled tubing steel is rolled by Thermo-Mechanical-Control-Processing (TMCP), and it is obtained that the yield strength and tensile strength of Nb microalloyed coiled tubing steel are 565MPa and 685MPa respectively, and the elongation percentage is 30.1%.IntroductionCoiled tubing is widely used in oil field for well logging, well completion, drilling, work over and other operation in various fields to solve a number of conventional operating techniques problem which are difficult resolved, and it plays a more and more important part in exploration and production at oil field. [1] It will improve the efficiency of exploration and exploitation, studying, developing and using coiled tubing technology. Therefore, the development of domestic coiled tubing materials and manufacturing technology are great significance. It is well known that Coiled tubing has relatively poor working conditions and complex force state. So, the coiled tubing needs satisfier a kind of high strength, high plasticity, and corrosion resistant under complex oil gas condition. As the coiled tubing technology developed, the level of the coiled tubing steel is from CT55 originally to CT90 and CT100, and the corresponding tensile strength is 483MPa-758MPa. [2, 3]"

Jan 1, 2012

By H. J. Thevik, A. K. Dahle

"A mathematical model that calculates the stress development in a coherent and stationary dendritic network due to interdendritic flow is proposed. The fluid flow is assumed to be related to the solidification shrinkage, and under the assumption of no porosity formation and unidirectional solidification, the shrinkage-induced flow within the mushy zone is calculated analytically. The interdendritic melt flow exerts a force on the solid network and an analytical expression for the stress build-up in the network is developed. Parameter studies illustrating the influence of cooling conditions, mushy zone length, dendrite coherency, fraction solid, volume fraction of eutectic, and solidification shrinkage upon the stress development within the solid network are presented. Comparing the magnitude of the calculated stresses to measurements of the strength in equiaxed mushy zones shows that it is possible for the stresses to exceed the strength, thereby resulting in reorientation or collapse of the dendritic network.IntroductionInterdendritic fluid flow is at present regarded as a very important mechanism for feeding of shrinkage during solidification of metal alloys. Solidification of many alloys is often characterised by heterogeneous nucleation of the primary phase on substrates in the melt with subsequent evolution of equiaxed dendrites. These equiaxed dendrites can initially grow freely, but impinge on each other and form a continuous dendritic network, ie. dendrite coherency, quite early in the solidification process. Measurements of the dendrite coherency point have shown that the dendritic network is established at solid fractions ranging between 0.1 and 0.5, and most often around about 0.2 [l]. Depending on the alloy composition this means that as much as 70 to 80% of the volumetric shrinkage has to be compensated by flow of liquid through the interdendritic network. Interdendritic flow occurs with a much larger resistance compared to free flow of the liquid and flow of a liquid with dispersed crystals. The pressure drop associated with the interdendritic flow increases rapidly with decreasing fraction ofliquid."

Jan 1, 1999

By Cindy L. Williams

"The Blue Star subdistrict in the Carlin Trend, Nevada, includes multiple mines with 33.9 t Au in reserve and past production totaling 89 .1 t Au. The deposits are characterized by zoned alteration mineralogy and gold grades. From orebody centers outward the zones include: 1) a silicified core with erratic gold grade; 2) adjacent mill-grade (> 1.37 Au git) intense quartz-sericite-pyrite alteration; 3) enveloping leach-grade (0.21 Au g/t to 1.37 Au git) weaker sericite-kaolinite-quartzpyrite alteration; 4) surrounding decarbonatized and intensely argillized waste and leach grade ore; 5) pervasively decarbonatized waste rock; and 6) peripheral waste with weak decarbonatization and local propylitic alteration. Zoned alteration extends as much as 1500 m beyond orebodies.Understanding Blue Star subdistrict zoned alteration assemblages and gold grades has increased geologists' ability to provide practical and economically significant information to geotechnical engineers, mine planners and drill and blast personnel. Alteration influences geotechnical pitslope design because each assemblage has distinct rock strength. Geotechnical engineers use three-dimensional models of incompetent alteration types as a foundation for pit-slope design. In the drill and blast cycle, hard and soft alteration types require modified practices (powder column, blast hole spacing, delay design etc.) for optimum blast energy distribution. Further, geotechnically instable alteration types require careful blast procedures to prevent backbreak whic~ damages ultimate walls. In addition to mine planning and mining applications, zoned alteration assemblages extending beyond orebodies provide a useful exploration guide. Metallurgical character also varies with alteration type. Intensely quartz-sericite-pyrite altered or silicified ore has relatively high partical-size dependency and poor leach recoveries. Moderately sericite-kaolinite-quartz-pyrite altered rock, in contrast, shows little size dependency and good leach recoveries.The author sincerely thanks L. Schutz, P. Williams, C. Clode, W. Trudell, P. Herrera, M.DKunkel, M. Goings and numerous other Newmont geologists, metallurgist, engineers and support staff who made this paper possible."

Jan 1, 1997

By Tatsuo Inoue, Marnoru Mizuno, Toru Matsuoka, Kenichiro Abe

"The distribution of particle reinforcements and the residual stresses in metal matrix composite are simulated by considering the motion of particles and the solidification of matrix associated with temperature variation in the course of centrifugal casting process. In the analysis, a heat conduction equation including heat generation due to latent heat and also mechanical work as well as heat input from successively accumulated element on the air/metal boundary is solved by the finite element technique. After the movement of particles subjected to the centrifugal force and drag are analyzed, the residual stresses are elucidated by using a unified constitutive equation which can describe the behavior both in liquid and solid states. Results of the simulation are compared with the experimental data, and the validity and utility of the procedure is confirmed.IntroductionProcess simulation of metal matrix composite (MMC) is required to determine the mechanical properties of the materials and the efficient process and conditions of the fabrication. Properties of bonding matrix with reinforcements in the course of the processing, for example, affects the strength of the composite, while the final costs of the productions depends on the efficiency of fabrication. Therefore, the simulation of processing of MMC is prerequisite in order to clarify the mechanism to fabricate the material which has been expected to maintain high mechanical properties and the cost performance.Some techniques of processing MMC[l] have been developed so far. Among them, the centrifugal casting technique [2-5] has many attractive characteristics as processing of the MMC: The centrifugal casting technique makes the reinforcements such as particles or short fibers to be distributed in the radial direction by the centrifugal force acting on reinforcements due to the difference in density between reinforcements and matrix. Since the distribution of reinforcements affect the mechanical properties of MMC, the composite with functionally gradient mechanical properties can be provided by the centrifugal casting technique."

Jan 1, 1994

By Yan Fu, Chuanlin Fan, Xiujing Zhai, Yongfeng Chang, Binchuan Li

"The mechanism of the selective chlorination of nickel and cobalt in reduced limonitic laterite was investigated. Reduced ores were obtained from the reduction roasting of a limonitic nickel laterite. The thermal decomposition of related chlorides and the selective chlorination of the reduced ore were carefully studied using Differential Thermal analysis - Thermogravimetry (DTA-TG), X-Ray Diffraction and chemical leaching methods. In the temperature range of 300 - 500 °C, aluminum chloride hexahydrate was chosen as chloride agent. During the selective chlorination, reduced ore was partly chlorinated by hydrogen chloride generated from the thermal decomposition of chloride agent. Then the oxydrolysis of ferrous chloride re-generated hydrogen chloride was used to further the chlorination. Finally, iron was mostly rejected as hematite, while nickel and cobalt were selectively chlorinated. More than 91 %Ni , 90%Co and about 4%Fe in the chlorinated ore was extracted using a water leaching method.IntroductionLimonitic nickel laterite is an important nickel reserve, which is rich in iron in the form of goethite and has low contents of magnesium, aluminum, silicon, and other elements. Goethite is the main nickel-bearing mineral in the laterite [1]. Nickel is generally present in goethite in three modes: (a) associated with amorphous or poorly crystalline goethite, (b) weakly adsorbed to the crystalline goethite surface, and ( c) as lattice substituents [2]. In addition, cobalt in limonite was found to be associated with a manganese phase rich also in nickel [3]. These results indicate that the extractions of nickel and cobalt are highly dependent upon the degree of the decomposition of the nickel, cobalt-bearing minerals.For the selective extraction of nickel and cobalt from limonitic laterite, the ore is usually processed by hydrometallurgical methods, including high pressure acid leaching (HPAL) [4] or reductive roasting - ammonia leaching (Caron process). However, there are still some disadvantages in these processes, such as the expense of autoclaves and scaling problems in HP AL [ 4, 5], and relatively low overall metal recovery, large energy and reagent requirements for the Caron process."

Jan 1, 2011