Search Documents

By P. Myllykoski, J. Nylander, A. S. Korhonen, J. Larkiola

The coefficient of friction and the deformation resistance have been determined from the measured rolling parameters by applying the Bland-Ford-Ellis rolling force model and the artificial neural network model (ANN). The dependence of friction on the parameters such as reduction, rolling speed, front and back tensions, contact pressure and deformation resistance have been studied by the ANN model. Measured data of over 10 000 coils have been used in the training stage. Various dependencies have been examined and the results show that the friction coefficient does not depend much on the rolling speed. The reduction and deformation resistance seem to have the strongest effect on the friction coefficient. A friction model based on neural computing has been included into the existing rolling force model.

Jan 1, 1994

By Edwin de Jesús Deveaux

After 32 years of operations beneficiating lateritic nickel ore in a fully integrated pyrometallurgical complex, Falconbridge Dominicana (FALCONDO), situated at Bonao and La Vega Provinces, Dominican Republic, has become profitable with one of the lowest nickel grade content processing plants in the world, and literally without any by-product (granulated slag, will be utilized in the future as a post-processing subproduct). To December 2002, mineral reserves were 64.1 million tonnes containing laterite grading as low as 1.15 % Ni when full dilution is applied. At a cut-off grade of 1.20% Ni, the reserves will provide 15-20 years of production. The mineralized thickness over the seven active deposits averages 6 m. Development of very selective and unique mining practices, together with improvements in the process plant, are key to achieving the production goal (30 kt Ni/yr) and to meet the quality standards for the ferronickel produced. Keywords: Laterites, grade control, mining methods, environment

Jan 1, 2004

By Lifeng Zhang, Zineb Benouahmane, Yaqiong Li

Experimental oxidation tests at high temperature (1000-1200 °C) on SiC samples have been respectively performed under wet and dry air atmosphere for different holding times. The thickness of thermally grown oxide was experimentally measured by DEKTAK Stylus Profilometry. The results showed that the oxidation rate was increased with temperature and holding time, corresponding to a passive oxidation regime which led to the formation of SiO2 layer. The sessile drop method was employed in order to measure the contact angles between Si and SiC at high temperature. Contact angle can be varied from 39.6° to 75.6° by controlling the atmosphere. The deoxidation of the oxide layer and infiltration of liquid silicon caused a decrease in the contact angle.

Jan 1, 2016

By S. S. B Wang

Zirconia-based ceramic materials have potential applications in high temperature furnace insulation, hot extrusion and casting dies, pressure nozzles, cutting tools, engine parts and electronic materials. High purity and superfine powders of zirconium oxide (baddelyte) were synthesized from a solution containing zirconium oxychloride and urea under hydrothermal conditions. crystallization of the metastable tetragonal zirconia using magnesium oxide or yttrium oxide as stabilizing agents was successfully achieved. The mechanism of hydrothermal reaction to produce these powders are discussed.

Jan 1, 1989

By M. A. Llavona

In Spain, as in many countries, the gold content of jewellery must be officially hallmarked. The official methods of assay are gravimetnc cupellation (a method which is highly accurate but both time and sample consuming), potentiometry, gravimetry and volumetry. In this paper, a procedure for measuring gold by flame atomic absorption in jewellery samples is described. The method is based on the acid digestion of a 40 mg sample. The quantity of aqua regia necessary for dissolving the gold, the ideal weight of a sample in order that the error may be minimal, the effect of the acids employed, the type of material used for its storage, and the necessity of employing a buffer to avoid the ionization of the solution are described. The method proposed is simple, highly accurate and causes little damage to the jewellery.

Jan 1, 1999

By Chao Zhang, Jian Guo, Chaoquan Yao, Leige Xia, Xinyu Li, Jianliang Zhang

In this research, analytical reagents were used for the sintering experiments. And the sinters were using X-ray diffraction, scanning electron microscope and mineralogical microscope analysis to study the effect mechanism of manganese on the silico-ferrite of calcium and aluminum (SFCA) bonding phase formation during the sintering process. The results indicated that the increasing content of manganese would greatly reduce the content of SFCA, and promote the formation of calcium aluminum silicate and the amount of pores and cracks. The existence of manganese inhibited the silicon form into the SFCA and a great deal of Fe2O3 was participated in the crystal transition to Fe3O4. When the ratio of the added manganese was less than 3% in the mixing, the calcium ferrite was in substantially interleaving corrosion with hematite and magnetite. Both the porosity and silicate glass phase content were low simultaneously, which contributed to the sintering production.

Jan 1, 2015

By Gus Van Weert

This paper describes the results of autoclave testwork where ferric nitrate was hydrolysed in the presence of certain cations and anions and the resulting hematite analyzed for foreign constituents. For the cations Zn++, Ni++, Cu++, and AI+++, selectivity factors of over 107 were found. Magnesium gave 3.106. These factors are calculated as Me/Fe in solution over Me/Fe in the hematite; Me representing the metal in ion added. As-a result of the testwork at Delft University of Technology, BUDELCO (the Netherlands electrolytic zinc producer) ran a series of ferric nitrate hydrolysis tests in the presence of 10 additional trace elements. Impurity levels were prejudiced on Me2 EPHA extraction of iron from their zinc circuit, followed by HNO3 stripping. Good selectivity against base metals was confirmed, but trace elements forming anions (As. Sb) and sulphate were incorporated in the hematite. These BUDELCO results are also presented.

Jan 1, 1995

By Masayasu Kawahara

"The extraction and separation of nickel, cobalt and copper were investigated with a solvent impregnated resin which was produced from UX84-I and XAD-4. The extraction behavior of metals with the solvent impregnated resin is similar to that with solvent extraction. The extraction ability of solvent impregnated resin improves when using finer particle resin and with a higher concentration of extraction solvent.IntroductionSolvent extraction is well known-as a method for separation of metallic elements in solution. However there are problems with intermediate phase and solvent loss. Ion exchange resin is also used in hydrometallurgy, but it is not fit for separating a large quantity of metals. Amberlite XAD-4 resin is known as a absorption agent of organic matter in water. It is expected that the resin which has the ability of extracting metals can be made by absorbing organic extractant on XAD-4 resin In this study, solvent impregnated resin (SIR) was produced from LIX84-I and XAD-4, and extraction and separation of nickel, cobalt and copper were conducted using SIR. The extraction properties of SIR were investigated, and a comparison between ordinary solvent extraction and SIR was made.Experimental ProcedureAmberlite XAD-4 was used as absorption resin for the organic extractant in this study. The physical properties of XAD-4 are shown in Table I. Amber lite XAD-4 has a large surface area and shows good ability to absorb organic matter in water, but the: resin does not have the ability of exchanging metallic ion."

Jan 1, 2000

By Jun Miao, Kang Liu, Jilai Xue, Jun Zhu

CO2 emissions must be reduced by at least 50 % by 2050, and hence the technical solutions to capture and convert CO2 into value–added products should be considered. A Cobalt(III) Schiff base complex (Salen–Co(III)) has been investigated as a catalyst for synthesis of cyclic carbonate from CO2 and epichlorohydrin(ECH) with tetrabutylammonium bromide (TBAB) as co–catalyst. To recover Salen–Co(III) for the next cycling operation, it was immobilized onto zeolite 13X through excessive impregnation method. The immobilized catalyst was characterized using XRD, SEM, BET and ICP–AES techniques. Catalytic tests showed that yield of cyclic carbonate reached 90 % using 0.5 mol % Salen–Co(III) at ambient conditions. The immobilized Salen–Co(III) exhibited better catalytic activity than the homogenous one when used at the first cycle, but the yield decreased by some 20 % after five cycles.

Jan 1, 2015

By Md Sazzadur Rahman

Electrochemical Impedance Spectroscopy studies were conducted on two organic thermal energy storage materials; Neopentylglycol (NPG) and 2-Amino-2-Methyl-1,3-Propanediol (AMPL). The ionic conductivities and dielectric relaxation times in the low temperature ordered a-phase (monoclinic for both NPG and AMPL) as well as high temperature orientationally disordered cubic y-phase are reported.

Jan 1, 2006

By H. Y. Sohn, Haitao Wang, Moo Eob Choi

"A novel ironmaking technology is under development at the University of Utah. This technology produces iron directly from iron ore concentrate by gas-solid suspension reduction. Hydrogen is the main reducing agent for high reactivity and for the elimination of carbon dioxide release in this ironmaking process. The direct use of concentrates allows bypassing the problematic pelletization/sintering and cokemaking steps in the steel industry.Intrinsic kinetics of the suspension reduction of magnetite concentrate particles by hydrogen has been measured. Experiments were carried out in the temperature range of 1423-1673 K, other experimental variable being hydrogen partial pressure, the amount of excess hydrogen and particle size. Under most experimental conditions, 95% reduction was attained within several seconds, which presents sufficiently rapid kinetics for a suspension reduction process. The reaction kinetics followed the nucleation-and-growth equation, and a rate equation that contains all the effects of the experimental parameters has been obtained.IntroductionWith the rapid increase in steel production, it is critical to control CO2 emissions which is the main greenhouse gas. It is inevitable to release a huge amount of CO2 when coke and/or coal are used as the main reducing agent in producing iron. As one of the methods to reduce the CO2 emission from ironmaking, the utilization of the gaseous reducing agents and fuels, including hydrogen, has been investigated [1-6]. The use of such gases forms the basis for a new ironmaking technology under development for producing iron directly from fine concentrates by a gas-solid suspension technology. This technology would reduce energy consumption by about 40% of the amount required by the blast furnace and drastically lower environmental pollution, especially CO2 emission, from the steel industry [4]. This is accomplished by adopting H2-based reductant and bypassing pelletization/sintering and cokemaking steps. Unlike other gas-based alternative ironmaking processes using shaft furnaces or fluidized-bed reactors, the suspension reduction technology is a high-intensity process because it will not suffer from the problems that other processes do when operated at high temperatures mainly from the sticking and fusion of particles."

Jan 1, 2011

By Nobuhiro Ishikawa

The in-situ observation of the effect of impurities on the reduction process of iron oxides by C in TEM was carried out. A few wt% of CaO or AbO, was used as impurities in FeO was prepared. Some precipitates grew into the C layer expect for using 3.0wtCa. The reaction between FeO and carbon was much different from using pure FeO at about 800-1 lOOK. The rate of reaction became much slower including Ca and almost no reaction was happened with the concentration of CaO up to 3.0wt%. On the contrary, AbO, had ahuost no effect on the reaction. The results indicated that Ca suppressed the reaction and the effect of Al was much less. The precipitates which grew into C layer accompanied almost no Ca and AI. Only Fe was detected in the precipitates.

Jan 1, 2008

By Charles H. Rawlins

Reported is work done on processing of steel mill effluents in the areas of dewatering and separation. Much of the waste from these operations is in the form of sludges from scrubbers, in which the primary constituent is iron oxide. Recycling of the sludge&apos;s magnetic fraction has become economically attractive in order to reduce the overall volume placed in landfills. The objective of this research is to determine the effectiveness of combining magnetic and cyclonic forces, to recover iron oxide particles from waste water stream, while decreasing the volume to be disposed. Three different size hydrocyclones, operating within the field of a quadripole magnet, were tested using varying feed pulp densities of magnetite, magnetite/dolomite, blast furnace (BF), and basic oxygen furnace (BOF) slurries. In the first three cases, the percentage of magnetics recovered increased to greater than 95%. The limiting operational factors are; high pulp density for small cyclones, which can cause flow blockage within the magnet field, and extremely fine particle sizes (<2 microns), which cannot be recovered. The results indicate this technique can remove virtually all the magnetic particles from some steel effluents to a 40-50% weight percent solids pulp, on an in line continuous basis.

Jan 1, 1994

By Satoshi Yamashita, Noboru Masuko

"Newly prepared bipolar membrane is promising to become a key material of an electrolyser for a production process of strong reducing solvent. This research is basic research for using bipolar membranes as electrolysers of reducing agents, Cr(II), TI(III) and V (II) on the laboratory scale. In this report, a bipolar membrane was tried with an electrolyser, reducing chromic chloride to chromous chloride. An analysis of mass balance demonstrates advantages of it over the former electrolyser equipped with an anion and/or. cation exchange membrane. The effects of current density and concentration of Cr(lll) on the reduction rate of Cr(II) and the current efficiency were examined No deterioration of the bipolar membrane resulted from the electrolytic reduction of Cr(III). IntroductionRecently, bipolar membrane that was the development subject for a long time in the industry of ion exchange membranes has met the stage of the practical application at last [l]. The expectation of the application to the hydrometallurgy field increases. We took up the manufacturing of the strong reducibility solvent as part of the application of bipolar membrane to hydrometallurgy technology. This laboratory has much experience in the electrolytic reduction of Cr (II) aqueous .solution such as chromous sulfateusing bipolar membrane were compared in theory to chromous chloride aqueous solution manufacturing of the strong reducibility solvent. The advantage of applying bipolar membrane by substituting ion exchange membrane is described, and the experimental result is reported."

Jan 1, 2000

By K. Osseo-Asare

Aqueous stability diagrams (25°C) are presented for the systems M-H2O and M-Oxalate-H2O where M=Sm, Nd, Co, and Fe. With the aid of these diagrams (i.e., Eh-pH and log[Metal]- log[Oxalate]), the solution-chemical constraints on metal dissolution and precipitation are identified. By comparing the corresponding stability diagrams, conceptual flowsheets are developed for metal recovery from Sm-Co and Nd-Fe-B magnet scrap.

Jan 1, 1997

By N. El-Kaddah, V. L. Acoff, M. Arenas

"Control of the weld penetration, weld pool shape and temperature field in arc welding is critical to achieve the desired microstructure and mechanical properties in the resultant welds. This is particularly important in welding gamma titanium aluminides (y-TiAl) where the weld pool is relatively shallow and the temperature gradient in the heat-affected zone is quite steep. This paper investigates theoretically and experimentally the evolution of the shape of the weld pool for stationary gas tungsten arc welds in y-TiAl alloys. A mathematical model has been developed for predicting the electric current flow, the resultant electromagnetic forces in the metal, and the transient development of the temperature and velocity fields in the molten pool generated by a spatially variable heat flux at the arc-striking zone. The governing equations were solved numerically using the control volume technique. Welding experiments were carried out to determine the shape of the weld pool and the extent of the heat affected zone at different welding times for model validation. The numerical predictions were found to be in reasonable agreement with measurements. It is suggested that the model presented in this paper is likely to provide the information needed for predicting the microstructure and mechanical properties of y-TiAl welds. IntroductionIn recent years, there has been considerable interest in the welding of gamma titanium aluminides as a means of manufacturing high-temperature, high-performance components for turbine and automobile engines. These alloys are highly reactive, and must be welded in vacuum or inert gas atmosphere, rendering electron beam, and inert gas tungsten arc welding (GTA) to be the only suitable welding techniques for joining these materials [1-3]. The GTA welding is especially attractive because of its flexibility and relative cost-effectiveness. However, previous studies on the weldability and weld properties of these alloys using this process revealed a decrease in the mechanical properties in the fusion zone [4]. This is generally attributed to the change of the original duplex structure to a dendritic structure amplified by the shallowness of weld spot. Quantifying the effect of arc operating parameters on the geometry and temperature profile of the welding pool prior cooling is the first step for controlling the fusion zone microstructure and mechanical properties."

Jan 1, 1999

By Scott R. Giese, Lucas Dix

"Recently, there is a growing trend in the aluminum foundry industry to develop· improved melting and casting processes to produce lightweight, high-strength, and thin-wall castings for the aerospace and transportation industry. One casting method that has demonstrated industrial potential for producing clean, thinwall castings is vacuum-assisted, counter gravity casting. This process has the benefit of expeditiously and quiescently filling the casting cavity with a dramatic reduction of furnace related and reoxidation inclusions. Additionally, lower casting temperatures can be utilized because the application of vacuum during filling overcomes the resistive internal cavity pressure resulting in a finer, as-cast microstructure. The paper explores and discusses the processing and design conditions in improving the mechanical properties of A206 casting alloy using the vacuum assisted, counter gravity casting process.IntroductionThe process of metal casting has been, over the centuries, the chief production technique for components used in everyday life. However, the casting process has certain inherent problems that can adversely effect the properties of a finished product. These problems are directly attributable to the gravity pouring technique used to transfer molten metal to the mold and to fill the mold cavity.A recent study for the American Metalcasting Consortium demonstrated reoxidation products created during the casting process are five times more likely to cause product rejects than entrapped molding aggregates, melt slag, or furnace lining materials1. Formation of nonmetallic and intennetallic compounds are more prevalent in aluminum and titanium alloys because of their reactiveness to furnace lining materials and their high affinity for oxygen. The incorporation of undesirable compounds can be attributed to four areas of the casting operation. The sources are charge materials, melting technique, pouring methodology, and casting cavity filling. Aluminum foundry men have addressed the first three areas by selecting high quality melt stock, non-stirring melting equipment, and the use of porous ceramic filters. Unfortunately, little consideration is given to the last, but yet tl.1e most important part of the casting operation, the actual fill mg of the casting cavity.The generation of inclusion defects during the casting process can be described by two methods. As the liquid metal flows in the gating network and casting cavity, abrupt changes in flow d1rect10n cause the metal to become agitated. This mechanism liquid metal splashing, is generated by instability of the advancing liquid metal interface from turbulence effects as schematically illustrated in figure 1a2 . The surface oxide film bursts under high velocity conditions, folds over, and becomes dispersed and incorporated in the bulk liquid. Additionally, fragmented liquid droplets ejected from the disturbed interface oxidize and become dispersed in the metal stream."

Jan 1, 2000

By KNona C. Liddell

The time and spatial dependence of component and species concentrations during in situ uraninite leaching have been modeled using a reactive transport model based on partial equilibrium between reactive minerals and the solution. The flow field is represented by mixing cells in series. The effects of the H2O2, (NH4)2CO3, and NH4HCO3 component concentrations have been simulated, and results are presented for a one-dimensional flow field.

Jan 1, 1995

By Metehan Erdogan, Furkan Özdemir, Ishak Karakaya, Mustafa Elmadaglı

Tungsten is mainly produced by H2 reduction of WO3 which makes its production difficult and costly. A promising method was recently reported for direct electrochemical production of tungsten from CaWO4 (scheelite) which is estimated as the seventy percent of the all tungsten reserves of the world. This paper investigates the application of pulse current in the electrochemical reduction of CaWO4 pellets attached to a current collector. The electrolyte was composed of calcium chloride and sodium chloride salts at eutectic composition (48 pct mol NaCl at 873 K). The reduced samples were cleaned with dilute hydrochloric acid solutions and characterized by X-ray diffraction and scanning electron microscopy. Examination of the results revealed that metallic tungsten was obtained by pulse current reduction.

Jan 1, 2016

By J. Tang

The major problem with the Nd-Fe-B magnet is its low operating temperature, i.e., the coercivity decreases so rapidly with increasing temperature that the practical maximum operating temperature-is only 100 °C. Meanwhile, it has been reported that nitrogen addition can drastically increase the Curie temperature of both R2Fe17 and RTiFe11 (R = rare earths). A reasonable question is, then, can one see a similar effect in Nd-Fe-B system? Experiments have been conducted to examine how magnetic properties of Nd-Fe-B magnet are affected by the nitrogen addition. Our results show that part of Nd2Fe14B maintains its original crystal structure and no substantial change in To, due to such N2 treatment is found. However, part of the sample decomposes into a-Fe and, possibly, Nd nitride as a result of nitrogen treatment.

Jan 1, 1992