Search Documents

By Robert E. Barry

For new coal-fired power plants, federal regulations require that emissions of sulfur dioxide be limited to 1.2 pounds for every million BTU'S burned. This is equivalent to coal with a sulfur content of roughly 0.7 percent for Eastern bituminous coals and roughly 0.6 percent for Western sub-bituminous coals. The states and their political subdivisions are free to apply more stringent standards and to develop implementation plans covering existing and new units. Most Western-sub-bituminous coals contain less than 1% sulfur and hence their use, in many cases, will allow a utility to meet the regulations. However, there are problems in using such coals in furnaces designed for Eastern bituminous coals, and furthermore it will take many years to open mines and provide transportation facilities to utilities which are now burning coals with a higher sulfur content. Moreover, pending federal legislation would outlaw strip mining on land to which the federal government owns the mining rights. Those utilities who, for one reason or another, intend to continue burning Eastern bituminous coals with sulfur contents in excess of 1 percent are faced with removing SO2 from the stack gases. The alternative of utilizing coal gasification where the sulfur is removed prior to burning in a power plant is still in the early stages of development. Therefore, a large number of processes are under development for SO2 control.

Jan 1, 1974

By L. C. Bartel

Geologic features such as structure (faults, folds, fractures, etc.), water bearing zones, aquifers, pemeability variations, and porosity variations are important for mine planning and in situ energy recovery processes. Features important for planning a mine will be important for planning the recovery of energy by in situ processes. Various geophysical techniques might be used to obtain the necessary geologic information. In this paper, case histories will be discussed of the use of electromagnetic geophysical surveys at a potential underground coal gasification site and a potential tar sand oil recovery site to obtain pertinent geologic information. Results show that the controlled source audio- frequency magnetotelluric technique shows promise for mapping faults and natural fracture systems when there is a sufficient resistivity contrast.

Jan 1, 1982

By Jeffrey A. Holcomb

INTRODUCTION The passage of Comprehensive Environmental Response Compensation and Liability Act (CERCLA/Superfund) as well as the Resource Conservation and Recovery Act (RCRA) and state laws, have placed added regulatory pressures on the mining industry. These laws which focus on the regulation of hazardous substances and wastes for the protection of the public health and welfare and the environment, present the potential for tremendous financial impacts and liabilities on existing mine operators and owners and/or potential mine operators/owners. This paper takes a brief look at these laws and presents an environmental audit procedure to identify environmental liabilities prior to mine land transactions. The environmental audit approach presented is an overview of the procedures that could be used to document, evaluate and inventory existing and/or potential environmental concerns. This audit procedure can be applied to developed or undeveloped properties and at active or inactive mining sites. REGULATORY OVERVIEW Mining environmental liabilities have been addressed in RCRA, Superfund, the Clean Air Act (CAA) and the Clean Water Act (CWA). Even though the U.S. Environmental Protection Agency (EPA) has determined that mining wastes will be treated as solid wastes under RCRA and not as hazardous wastes, these wastes could still bring about a great deal of financial liability under Superfund. The catch is if the mine wastes generated contain hazardous substances such as the heavy metals arsenic, beryllium, cadmium, chromium, copper, lead, mercury, nickel, selenium, silver, thallium, zinc and others as well as cyanide. Thus, it is not only important for a mine operator/owner or a potential mine operator/owner to know if the mine wastes generated are hazardous, but it is important to know if the wastes contain hazardous substances. Following is a brief overview of RCRA and Superfund and their potential implications. RCRA RCRA, which provides the basis for the regulation of solid and hazardous wastes, is applicable to active mining and milling sites. Within RCRA the definition of a hazardous waste is provided. This definition applies to owners and operators of mining and milling sites if the operator has stored, disposed or treated hazardous wastes on-site. If this is the case and if strict process control and waste management activities are not adhered to, environmental liabilities may be associated with the site. Superfund The 1980 Superfund law can be applicable to inactive mining sites or to inactive sections of an active facility. The provisions of Superfund call for the regulation of hazardous wastes and hazardous sub- stances disposal and release not only by the existing owner, but also for any previous owner. This concept of joint and several liability means that one party, as among many, can be held totally responsible for the costs of hazardous waste cleanup (Haller, 1987). Furthermore, liabilities under Superfund have also been applied back to past acts; thus, several mining properties, active or inactive prior to the 1980 Superfund law, are at risk of being placed on the EPA's National Priority List (NPL) for cleanup. Last years amendments to Superfund, known as the Superfund Reauthorization Act of 1986 (SARA), provided some significant developments for the mining industry. The major requirement of the amendments as it pertains to owners or operators of mining sites is that the EPA must revise its present Hazard Ranking System (HRS). This is important be- cause in most cases the primary reason for several mining sites having been included on the NPL was due to the large volume of wastes generated. As is typical at most mining sites, large volumes of low toxicity wastes are generated and the current HRS model prejudices against this. It should be noted that this provision only applies to sites that are not already on the NPL or have not been proposed for inclusion on the list.

Jan 1, 1987

By Duk-Wom Park

INTRODUCTION he most important information required for the engineering design of structures in rock is its inherent rock properties. Without providing adequate parameters on the rock property, high quality of the engineering design cannot be expected. Many laboratory rock testing methods have been developed, but they are mostly for testing intact homogeneous rock without appreciable discontinuities. In reality, the intact rock properties do not represent the behavior of rock masses because rock masses include irregularities such as joints, cracks, interlayers, variations in mineral compositjon, etc. In general the type and intensity of the rock defects may be much more important than the type of rock which will be encountered (Terzaghi, 1977; Bieniawski, 1984). In-situ rock testing can provide better information on rock parameters, but it takes a tremendous amount of effort, time and cost. In recent years, numerical modeling techniques are gaining popularity as a design tool for structures in rock bodies due to the enormous progress in computer technology (Wang, 1985; Kripakov and Melvin, 1983; Park and Ash, 1985), but it is quite dangerous to use numerical techniques without having proper input data. Bieniawski (1984) states as follows: Some design methods such as numerical techniques have outpaced our ability to provide the input data necessary for the application of these methods. In order to provide an adequate amount of input data, an extensive testing program may be required, thus major efforts in time and expenses are commonly spent, In this paper, a new rock testing method, which utilizes the principles of laser holographic interferometry, is introduced. This method requires only a few minutes to measure the modulus of elasticity and quality of a rock core sample, which does not have to be cut or ground. The Poisson's ratio can also be measured in a few minutes from a sliced rock specimen. HOLOGRAPHIC INTERFEROMETRY Principles of Holographic Interferometry In 1948, Gabor invented holography, which is the technique of reviving three dimensional images using a monochromatic light source. A full demonstration was not made then because a clean monochromatic light source was not available. Later, in the early 19601s, the laser was adopted as a monochromatic and coherent light source (Leith and Upatnieks, 1963). Since then, applications have been made in many different fields ranging from crime prevention to three dimensional television. In this technique, an image is usually recorded by means of constructing a hologram which is a record of the interference pattern formed on a high resolution photographic system as shown in Figure I. A beam splitter divides the laser beam into two beams: (1) an object beam which is expanded while passing through a beam expander and illuminates the object, and (2) a reference beam which is expanded and illuminates the holographic plate. Subsequent to an exposure, the holographic plate is developed and illuminated by the expanded reference beam. The original scene of the object is revived in a three-dimensional image. The entire instrument should be placed on a vibration free environment. The wave fields reflected by the object in two slightly different configurations can be superimposed to form an interference fringe pattern. Thus, it is possible to measure the displacement that took place between the two configurations. This method is called holographic interferometrv. There are two methods of achieving this phenomena. The first is the double exposure method, wherein two exposures of the object are made prior to developing the film. The first exposure represents the original condition and the second, the disturbed condition. The second method is the real time holographic method. In

Jan 1, 1986

Mine planners must select a single pit for design with the knowledge that the grades on which this selection is made are uncertain. This uncertainty is often ignored through the use of deterministic models of grade. This makes the mine planner?s job simpler but does not necessarily lead to the ?correct? or ?best? selection. Grade uncertainty is typically modeled with conditional simulation, which generates multiple possible realizations of grade that are equally probable (or improbable). M ethods for incorporating grade uncertainty into mine planning to date have either been perceived as being too complicated, not accessible or too time-consuming. This paper proposes a simple and efficient modeling approach to incorporating conditional simulation into pit optimization, which would be able to be applied in currently commercially available software. An example for R esolute M ining Ltd.?s Syama gold project in M ali shows the range of ore, grade and value outcomes associated with generating pits through a variety of methods.

Jan 1, 2013

By Hugh Jones

Mine planners are challenged to hold two seemingly opposing objectives: maximizing the mine?s operational efficiency while minimizing post-closure impacts. One of the most effective approaches to meet these objectives is to plan for mine closure from the start. Mine closure is typically viewed as the process that happens in the period of time when the operational stage of a mine is ending and the final decommissioning and mine rehabilitation is being undertaken. In reality, it is a continuous series of activities that begins with preplanning prior to the project?s design and construction and ends when long-term site stability is achieved and a self-sustaining ecosystem is established. Putting this model into practice as early as possible can significantly reduce the financial burden of mine closure and rehabilitation.

Jan 1, 2011

By A. W. Hamilton

If you don't know a gauss from a grasshopper, you may be better off than you, think, particularly if you're an ore dressing engineer charged with the responsibility of selecting magnetic equipment for minerals separation and beneficiation. Gauss is a unit of measure for a magnetic field. It indicates the number of imaginary lines of force per square centimeter or per square inch radiating from a magnet. In discussing the strength characteristics of a magnet, we have come to speak of a magnetic field of 800 gauss, for example, meaning 800 lines of force per square centimeter. Gauss became the standard for selecting drum type separators many years ago under an arbitrary set of circumstances. The standard has continued to this day even though magnetics applications engineers have long considered it inadequate. The configurations of the older gauss meter were such that the most accurate and convenient readings on a drum type separator could be made at distances greater than one inch. So, an arbitrary distance of two inches was established and that two inches became the standard. Since then, it has become commonplace to specify magnetic strengths for drum separators according to average gauss readings at two inches; for example 500 gauss average at two inches, 750 gauss average at two inches and so on, even though gauss readings at two inches have much less to do with the separating and beneficiating function of a given application than was formerly believed. The standard was adopted as a means of gauging the strengths of electromagnetic drum type separators, for they were the only ones around at the time. These machines were usually designed with no magnetic considerations other than that the material to be separated should be agitated vigorously and the magnetic fields should be deep and strong. Drums built this way performed well enough, so it seemed logical to measure their magnetic strengths. Hence, gauss at two inches. Now, new improvements in magnetic techniques have made average gauss measurements at 2 inches positively obsolete.

Jan 1, 1971

By C. Allen Born

There is a saying, the greater the gratitude, the shorter the speech. That puts me in a quandary, because while I am grateful for the honor you do me today, I also want to talk about a subject very important to all of us. A few months ago, when I was asked to submit a title for my talk, I chose "Quality where it counts." I did so because perhaps the most important thing we at Amax did in our restructuring was to commit to quality in all our businesses - quality people, assets, and operations. Together, they create quality performance, which produces quality growth and increased shareholder value - our prime corporate mission. We are dedicated to quality. At Amax, quality means everything. Today, I want to discuss quality in another context - the need for it in American education and what we have to do to achieve it. If we ignore this need, we will all suffer the consequences. And they will be upon us far sooner than the next century, barely a decade away. I think almost everyone in this room works for an organization that had to restructure in the 1980s. Mining companies that did not, just didn't make it. Well, we did. As an industry, we are seeing improved profits, positive cash flow, and a more competitive position in the world marketplace. But all the restructuring we have done, all the hard work, and all the pain that was part of it, will be in vain if, down the road, we do not have the educated people we need as workers. We need them to design, manufacture, and market the products that use the basic materials produced by the mining industry. Simply put, we are at a crisis point in education today. That is no new revelation. Nearly six years ago, the National Committee on Excellence in Education published its report, "A Nation At Risk." Since then, things have not gotten better. The Wall Street Journal, Business Week, US News & World Report, and Fortune have all recently published stories about the sorry state of education in the United States. The subject has become the topic of TV talk shows as well as national commissions, and for good reason. The pool of young people entering the US labor force is dwindling. In the next decade, 10 million fewer will enter the job market compared to the 1970s. But fewer of them will be qualified to do the jobs available to them. Here's why: • 20% of today's high school students drop out before they are 18 and another 20% graduate functionally illiterate; 40% of today's fourth graders think the world is flat; • 20% of today's sixth graders cannot locate the United States on a world map; • one of every three ninth graders cannot figure the change for a two-item meal - and I'm talking about a Big Mac and fries. These are not just problems of minority kids in big city ghettos. Fully 40% of all young working Americans cannot add up their lunch bill. Three out of every five college freshmen need some kind of remedial work. These statistics are frightening. Particularly so because, while the work force is becoming less qualified and our public education system is getting worse, our products and technologies are becoming more complex. We are approaching a time when we will have machines that recognize handwriting but people who cannot write. We will have technology to take voice commands, but people who do not know what they are talking about. The accelerating pace of technology is changing the nature of the job market. The fastest growing jobs now, and in the years ahead, are in professional, technical, and sales positions requiring the highest education and skill levels. Most of these jobs will require the use of a computer. Yet, 95% of today's graduating high school students have never laid a finger on a computer keyboard. While our education system is failing the students it is supposed to serve, other countries are doing far better. In a

Jan 1, 1990

By Inoka E. Perera, Michael J. Sapko, Marcia L. Harris

Experiments conducted with limestone dusts and dolomitic marble dusts have indicated that when rock dust is wetted and subsequently dried, it becomes a solid, non-dispersible cake. However, in order to be effectively inert a coal dust explosion, rock dust must be able to disperse as individual particles to air. To counteract this, rock dust manufacturers created treated rock dusts that will resist caking after moisture exposure. National Institute for Occupational Safety and Health (NIOSH) researchers conducted a series of laboratory-scale experiments on four base rock dusts and their treated counterparts to assess the effectiveness of various anticaking additives after being exposed tomoisture and then dried. The dusts were exposed tomoisture using humidity cabinets having a high relative humidity (99% RH) and by also exposing the rock dust bed to water through bottom wicking. The dusts were then evaluated for dispersibility after drying using the NIOSH-designed dust dispersion chamber. The anti-caking additives were different concentrations of stearic acid, oleic acid, and xylene-based surfactants. All results were compared to a reference rock dust used to conduct large-scale experiments in the Lake Lynn Experimental Mine (LLEM), Fairchance, PA. When the untreated dusts were dried after exposure to moisture for 1 day, no dispersion was measured. However, rock dusts treated with anti-caking agents were readily dispersible even after exposure to moisture for 6 months. This report details the analysis and characterization of anticaking additives using the NIOSH-designed dispersion chamber and the 20-L explosion test chamber.

Apr 12, 2021

By Don C. White

Santa Rosa is a mid-Tertiary, volcanic-hosted, bulk-mineable, open-pitable, heap-leachable, gold-silver deposit. It is the product of hydrothermal mineralization along an arcuate segment of a caldera collapse ring fault in a probable maar volcanic setting. This segment was later broken by radial faults. Gold occurs principally as electrum finely disseminated through intermediate tuffs, and associated with pyrite, at Santa Rosa. The nearby Alto de la Mina deposit displays stockwork silica-pyrite-gold in a tectonically and hydrothermally shattered andesite flow. Miocene epithermal mineralization was accompanied by central silicification and pyritization and more distal argillization. An andesite flow cap rock at Santa Rosa played a pivotal role as an upward permeability barrier. Highest gold grades and most intense alteration occur closest to the ring faults and immediately beneath the andesite flow. Supergene alteration effects on the gold distribution are minimal.

Jan 1, 1993

By D. Hulse

Mineral resource classification is described in both the SME and CIM Standards for Mineral Resource Reporting. The CIM Standard states “… sampling … is sufficient to assume geological and grade or quality continuity between points of observation”, thus is a function of continuity and sample spacing. Continuity can be measured by use of a variogram model, but average sample spacing in three dimensions is more difficult to measure. The declustering algorithms provided with Geostatistics software, are commonly used to weight data for statistical analysis due to the sometimes-irregular spacing between drill holes during exploration. The weights are lower when data is closer, reflecting shared influence between samples, and higher for isolated samples reflecting independence. This paper will discuss the potential to use estimates of the declustering weight as an inverse relative measure for average sample spacing to gauge the confidence of the estimate independent of the single nearest sample. PROBLEM The classification of mineral resources and reserves has long been a combination of science, past experience of the estimator, judgment, and feeling. All of the definitions as presented in the standards of the various countries that participate in CRIRSCO are similar and deal with “sample points sufficiently closely spaced to support confidence in the continuity of …” This has been interpreted as the distance between the block estimated and the nearest sample (or samples). Geostatistics gave us the calculation of the estimation variance of the block, an implicit part of the calculation of weights in Kriging, to account for the confidence in the estimate. More recently, “Kriging Efficiency” has been used, however it is still dependent on the estimation error and responds in a similar fashion to the distance to the closest sample. It is also sensitive to the variogram nugget. Many of these methods result in very low distance/high confidence measures for blocks adjacent to a sample point with confidence decreasing (sometimes rapidly) as the distance to one nearest sample increases. This results in the “spotted dog” phenomenon where individual samples are surrounded by a higher classification near each sample decaying into pattern of decreasing confidence halos. In addition to the visual image of the spots, this raises the more practical problem of mine design when the classification changes between measured, indicated and inferred. This has led to ad hoc methods to classify material within the mining block so all of the stope receives that classification. These manual methods re both labor intensive and subjective. A popular technique is a multiple search method, where the estimator defines a minimum of number of samples from a minimum number of holes within a nested set of search distance that are used to classify estimates. These specified set of increasing distances are usually proportional to the variogram range. While this is generally a good technique and overcomes the spottiness of the closest sample or kriging error, it has certain issues including:

Jan 1, 2019

By L. Diels

About 45% of the contaminated sites are dealing with heavy metal problems. Metals are spread in the environment by mining activities, surface treatment and non ferrous processing. As heavy metals can not be degraded, removal or immobilization (leading to bioavailability reduction) are the only risk reducing measures that exist. The currently best available technique for remediation of heavy metal contaminated groundwater is to pump the contaminated water and to treat it in a wastewater treatment plant installed on the surface. Next to this often used, but expensive, pump and treat technologies, heavy metals can be immobilized by inducing sulfate reducing bacteria (SRB) to transform the sulfates, that are very often present in the same groundwater (due to the metal mining or processing activities), into sulfides. These sulfides will precipitate the metals as insoluble metal sulfides. At the moment several studies have demonstrated the feasibility of this In Situ Bioprecipitation Process (ISBP) for the removal of heavy metals from ground-water as well at lab scale (batch and column tests) as at field scale. However, some questions arise concerning the continuation of the process, the efficiency and the sustainability of the precipitates. The presented study will try to answer these questions. The study is based on more than 10 different studies, all done by the same authors, on different groundwaters and aquifer samples. The presentation will give an overview of the guidelines necessary for a correct and successful bioprecipitation process with stable metal sulfide precipitates. An important question in the ISBP is related to the sustainability of the heavy metal precipitates. It could be observed that the interruption in the carbon source delivery also stopped the in situ bioprecipitation process. Depending on the metal also some release from the precipitate could be observed. It was shown that release can occur with Co and Ni. Aquifers, on which the metals precipitated during the ISBP, were treated in a sequential extraction process under an-aerobic and aerobic conditions. It could be shown that especially under the anaerobic conditions the Zn and Cd precipitates changed from the leachable and the exchangeable fraction to the organic or Fe-Mn fraction (i.e. from the unstable to the stable fraction). The same could be observed for Co and Ni but still some fraction was present under a more available form. On the other hand it could be shown that large differences were observed concerning the heavy metal speciation on the aquifer in function of the used carbon source during the ISBP. The molasses treated systems showed a much more available heavy metal fraction on the aquifer compared to the lactate or HRC® treated groundwater. The different speciation forms based on the use of different carbon sources will be discussed in detail. It will pay attention to the influence of the carbon source, the efficiency of the induction of the bioprecipitation process, the influence on the competence between sulfate reducers and methanogenic bacteria and the influence of low pH on the ISBP. It seems that acetate, which is also a degradation product of fermentation of some carbon sources, can inhibit some sulfate reducers. Also the relation between slow release compounds and immediately available compounds will be explained. Finally a pilot study will be presented showing the problems that can be encountered during this process. Focus will be put on the induction of the process, the keeping on of the process and the follow up of the process by the installation of in situ mesocosm socks. These results will allow the correct implementation of the ISBP with an eye on longevity and sustainability of the process and present the ISBP as a much more sustainable alternative to the pump and treat technology as measure for heavy metals contaminated groundwaters.

Jan 1, 2006

By Jeffrey L. Zelms

There is no known, practical substitute for lead in the automobiles, communications systems, medical equipment and computers that Americans use every day. However, there are many who say lead should be stopped at its source -- banned. As America's largest lead producer, The Doe Run Company has ralized that it must do more than mine and reclaim lead efficiently and safely. It must also earn the public's consent to operate if it is to continue to be a viable business. LEAD - THE BRILLIANT PERFORMER: REFURBISHING AN IMAGE It's been an embarrassingly long time since I was a college student. However, I remember there was no course at the University of Missouri's School of Mines and Metallurgy that had anything to do with the public relations aspects of mining or, put another way, the politicization of mining. It's been an embarrassingly long time since I was a college student. However, I remember there was no course at the University of Missouri's School of Mines and Metallurgy that had anything to do with the public relations aspects of mining or, put another way, the politicization of mining. I haven’t perused the course catalog for Penn State’s College of Earth and Minerals Sciences. But I strongly suspect I wouldn’t find such a course there today, either. A statement by the chairman of one of the country’s largest chemical companies leads to the point I want to make. He described his business this way. He said, “We’re a public affairs company that just happens to produce and market chemicals.” Like chemicals, minerals and mining are politicized today. To the extent that we don’t understand that reality, we don’t understand that reality – and act on it – we’re less likely to survive in this business. Some of you may well be saying to yourselves, “This guy Zelms is an alarmist.” That’s fair enough. Because it is absolutely true that there’s n o known, practical substitute for lead today. And it’s also absolutely true that, knowingly or not, Americans use lead everyday. It’s in our automobile batteries. It’s an integral part of communications systems. High tech (and low tech) medical equipment contains lead. And lead is an essential component of computer and TV screens. But even with all these uses, lead has a negative image today. An image so negative that its very existence is threatened. If you doubt that, consider these two statements made in 1989. Statement one. “It is probably reasonable to argue that exposure is the single most important and critical environmental health problem in the U.S., and possibly also the world…” Statement number two. “Many of the uses of lead should be terminated. We need to go back to the ultimate source: that is, taking lead out of the ground and putting it into the product stream and we need to turn it off at the ultimate source. Not the approximate lead in gasoline, or lead in air, or lead in food. Go right back to the source and start cranking it down." (End quote.) Those are what I call strong statements. And they weren’t made by some celebrity spokesperson for the environment like Meryl Streep. Both these statements were made by Dr. Ellen Silbergeld, whose long list of professional and academic credentials includes: o Adjunct professor and research scientist at the University of Maryland Medical School and Johns Hopkins: o Chief toxic scientist and director of the Toxic Chemicals Program of the Environmental Defense fund; o and President of the Society for Occupational and Environmental Health. If Dr. Silbergeld were the only person making these kinds of statements, it would be one thing. But she’s not a voice in the wilderness, by any means. Also for those of you who say, well since there’s no known substitute for lead, how on earth could it be banned. I refer you to a number of bills before Congress that would permit the EPA to ban any product if it is determined that its

Jan 1, 1992

By Trevor R. Ellis

In August 2011, the Southern African Institute of Mining and Metallurgy (SAIMM) contacted mining institutes and related societies internationally to assess their interest in participating in coordination of the review of the South African Code for Mineral Valuation (SAMVAL) with reviews of other mineral valuation standards. The main mineral valuation standards are the CIMVal Standard of The Canadian Institute of Mining, Metallurgy and Petroleum (CIM), the VALMIN Code of The Australasian Institute of Mining and Metallurgy (AusIMM), the SAMVAL Code, and the extractive industries? guidance note of the International Valuation Standards Council (IVSC), Valuation of Properties in the Extractive Industries, GN 14, designed for application within the full set of International Valuation Standards (IVSs). By January 2012, SAIMM had concluded that the level of respondent interest was adequate to organize a meeting. A meeting was scheduled for April 18, 2012 in Brisbane, Australia in conjunction with a VALMIN mineral valuation conference organized by the AusIMM. The stated purpose of the meeting was to develop an accord on terms of reference for pursuing harmonization of mineral asset valuation standards adopted by the participating mineral institutes. SME decided that, although it has not developed its own mineral valuation standard, it should participate in the Brisbane meeting and the harmonization process, as also did the American Institute of Minerals Appraisers (AIMA).

Jan 1, 2012

By DING TANG, JINGHE CHEN, Shuiping Zhong, CHEN KUANG

The Zijinshan gold-copper mine, located in Shanghang County, China, is a porphyry-type, low-grade ore deposit with a geological profile of upper gold and lower copper. Despite its low-grade nature, it has become one of the largest in production scale and most profitable nonferrous metal mines in China, which can be attributed to the successful application of hydrometallurgy as well as proper engineering design. A large-scale, open-air cyanide heap leach has been successfully implemented to recover gold under the humid and rainy weather conditions of southern China. Furthermore, according to the gold ore characteristics, a combination of gravity separation, carbon-in-leach and heap leaching processes was developed to improve gold recovery. In terms of copper extraction, copper ore of a grade higher than 0.25 percent is fed to the flotation plants to produce copper concentrate (gold is also enriched here), while copper ore of a grade lower than 0.25 percent undergoes heap bioleaching followed by solvent extraction and electrowinning to produce cathode copper. Additionally, a unique bioleaching system has been established at the Zijinshan Mine: low operating pH (0.8~1.0), high concentration of total soluble iron (~50 g/L), high temperatures (45~60 °C) and low activity of microorganism (~104/mL) in the pregnant leach solution (PLS). This review paper summarizes the practical experience acquired in developing the Zijinshan gold-copper mine and could be of use in other gold and/or copper plants.

By SAHENDRA SINGH, SANJIT KUMAR PAL, DHARMITA HORO

This study was carried out in Ichadih to map the sulfide/gold mineralization using combined electrical resistivity tomography (ERT) and self-potential (SP) methods. No geophysical analysis has been carried out to delineate such ore deposits in the area. Thus, the study provides a different approach for approximate location and extension of the quartz reef associated with sulfide/gold mineralization. It also provides the elementary idea for further detailed subsurface investigation in terms of geological and geophysical approach. 

By Taner Aydogmus

The A$29 billion Chevron-operated Wheatstone Project is one of Australia’s largest resource projects. Located at Ashburton North, 12 kilometers west of Onslow in Western Australia, the project will consist of two Liquefied Natural Gas (LNG) trains with a combined capacity of 8.9 million tons per annum and a domestic gas plant. The LNG Plant will serve the offshore gas fields, which are situated some 250 km off the coast of Onslow in Western Australia. Once operational and on-stream, the Wheatstone Project will contribute to Australia becoming the world’s second largest exporter of LNG. For crossing the environmentally sensitive shore area, a micro-tunnel with an internal diameter of 2 m and approx. 1,242 m in length has been constructed by means of the pipe-jacking method. The micro-tunnel will accommodate a 1.1 m diameter pipeline (trunkline) to deliver gas from the offshore fields LNG Plant. The Wheatstone shore crossing design involves a number of unique challenges owing to its coastal location, where the alignment crosses through a shore area and terminates in a marine environment. This paper provides an overview of the Wheatstone Shore Crossing Project, presents the key features, and discusses the main aspects of the micro-tunneling design.

Jun 13, 2021

By T. BACHMANN, G. SHAPLAND, E. Amini, N. BEATON, M. BECERRA

In this study, several methodologies to manage low grade and often competent portion of the ore have been proposed and tested in lab, pilot and operational scales. Relevant to this subject, the Cooperative Research Centre for Optimising Resource Extraction (CRC ORE) has developed Grade Engineering® (GE) concept to modify feed streams by rejecting the low grade and possibly hard components in the stream at the early stages of a value chain. Application of GE requires to understand the impact of the process on the value chain as they are value modifiers on in situ opportunities. Traditional modelling approaches and tools do not have the ability to run the analysis in a block model scale with high fidelity in an integrated value chain. Integrated Extraction Simulator (IES) in conjunction with sophisticated analytical tools such as a neural network (NN) was used to develop and reconcile a fully integrated value chain. The value chain model makes it possible to run all available blocks in the Geomet block model, which could be several millions, under possible scenarios for Grade Engineering for economic evaluation analysis and mine planning.

Sep 16, 2020

By M. Misra

The coral contaminated with plutonium at Johnston Atoll UA) was subjected to gravity and flotation separation processes at the Soil Washing Laboratory (SWL) and also at the Johnston Atoll UA) site. Tests were conducted with the contaminated coral fractions referred to as the "HP-l" ( hot particles) and the "sludge". The gravity process tested was centrifugal gravity separation and the flotation processes were conventional Denver mechanical flotation and tall column flotation. Flotation tests were conducted using both fresh and sea water. Industrial fatty acid (anionic collector) was chosen as collector to make plutonium-enriched particles hydrophobic. The use of flurosilicic acid and sodium silicate made the clean coral hydrophilic. The results show that each of the processed when tested with appropriate size fraction and operating conditions resulted in passing the success criteria. It was possible to obtain more than 80% weight of the original coral as "clean sand" having activity below the JA site "soil screening level" of 13.5 pCi/gm. The field tests spiked with plutonium particles showed remarkable success. The effect of depressants, flotation medium and the coral pretreatmentis described. Finally, a flowsheet developed by the University of Nevada, Reno to treat 8000 tons of HP-l pile presently stored at JA is presented.

Jan 1, 1996

By Yuting Xue

The classification of rock and coal will assist in automated coal rib rating and shearer horizon control, and is studied with machine learning techniques in this work. A database of rock and coal images is created by filtering photographs taken by researchers from the National Institute for Occupational Safety and Health (NIOSH). The classifier was trained with patches extracted from the coal and rock images, and an accuracy score of 0.9 was obtained. The trained classifier was then applied to classify rock from a new coal rib image with three rock layers of different thicknesses, and good agreement was achieved. The results demonstrate that it is promising to use machine learning techniques and rib images for rock and coal classification.