Search Documents

Extending an organization?s knowledge base throughout the entire enterprise can improve operations. Until recently, though, field operations were often left out of the information loop, as extending high-bandwidth communications into harsh environments often proved impossible due to thermal extremes, physical hazards and caustic chemicals. However, advances in the design and manufacture of rugged fiberoptic cables have now enabled the successful installation of 10-gigabit transmission links to places such as mining operations. The experience of Consol Energy exemplifies how plant managers can successfully enlist ruggedized tight buffered cables to help carry the efficiency of ERP communications into even the most challenging work environments. ?As part of our ERP implementation, we extended our corporate network underground into our mines using fi beroptic cable,? said Tom Prokop, manager-site support for Consol Energy. ?We?ve actually had rooffalls bury the cable between rocks and still did not lose data communications. Our maintenance personnel are now able to access our ERP system while underground at locations that can be up to 32 km (20 miles) away from their desks or the warehouse. Access to the corporate network allows them to order parts, look at electronic schematics, access monitoring data, no matter where they are in the mine. With a few hundred workers below ground, this immediate access translates into a time-savings that adds up in a hurry.?

Jan 1, 2009

By Xuchen Fan, Chenyang Zhou, Yuemin Zhao, Liang Dong, Chenlong Duan

A gas–solid fluidized bed using magnetite particles is an effective methodology for coal beneficiation in the field of dry coal cleaning. Broadening the size range of magnetite used in the bed decreases medium preparation cost. In this study, a tapered fluidized bed was used to investigate a magnetite particle size range of −0.5 + 0.074 mm. The results showed that a tapered fluidized bed effectively strengthens mixing of magnetite with a wide size range (−0.5 + 0.074 mm). The results of beneficiation experiments indicated that with increasing tapered angle, separation efficiency increased and then decreased. The highest separation efficiency was obtained at a tapered angle of 10°. The optimal results showed that the ash content of the concentrate decreased from 31.82% to 12.33% with a probable error of 0.11, which indicated that a tapered fluidized bed was efficient to improve fine coal beneficiation performance.

Minerals contribute to the U.S. gross domestic prod-uct (GDP) at several levels?mining, processing and manufacturing finished products. In 2008, the estimated growth rate for the real GDP of the United States was 1.1 percent and the nominal GDP was about $14.3 trillion (Table 1). Trends in various sectors of the domestic economy are often reflected in mineral production and consumption rates. For instance, continued declines in the U.S. housing market during 2008 were reflected in further reductions in the production and consumption of cement, clays, construction sand and gravel and crushed stone (mineral commodities that are used almost exclusively in construction), and those associated with the related manufacture of goods, such as ceramic tile, heating and air conditioning equipment, paint, plumbing and sanitaryware, roofing, wiring and wallboard ? all used by the housing industry. The widespread effects of the slowing domestic economy became more apparent in the last three to six months of 2008 when prices for many mineral commodities declined sharply after reaching record highs earlier in the year, indicating significantly lower demand for those materials or products containing them.

Jan 1, 2009

By A. Jarosz

The surface manifestation of underground mining usually entails five distinct types of surface movements, which can affect or damage surface structures, facilities and renewable resources. These movements developing at the surface can be described by (Bell, 1975; Bhattacharya and Singh, 1984): - vertical displacement, i.e. subsidence, - horizontal displacements, - slope or tilt, i.e. the derivative of the vertical displacement with respect to the horizontal distance, - curvature, i.e. the second derivative of the vertical displacement with respect to the horizontal distance, and, - horizontal strain, i.e. the derivative of the horizontal displacement with respect to the horizontal distance.

Jan 1, 1986

By M. Kuchta, A. Newman

LKAB’s Kiruna Mine, located in northern Sweden, produces about 24 Mton of iron ore yearly using sublevel caving. For efficiency, the mine must deliver planned quantities of three ore products. We use mixed integer programming to schedule Kiruna’s operations, specifically, which production blocks should be mined, and when they should be mined to minimize deviations from planned production quantities while adhering to mining restrictions (e.g., sequencing). A new production block database and a well-formulated mixed integer programming model dramatically reduce the size of the original problem; in less than ten minutes we generate five-year schedules with time fidelity of months.

Jan 1, 2002

By Yi Luo, Jian Yang, Hua Jiang

Surface subsidence induced by underground coal mining activities, especially longwall mining operations, can cause various problems to interstate highways ranging from structural integrity, drivability to safety. Accurate subsidence prediction, correct influence assessments, and effective mitigation measures are the keys to ensure the safety of highway traffic. The surface subsidence prediction program, called comprehensive and integrated subsidence prediction model (CISPM), was developed based on the principle of influence function method and has been validated with a large number of subsidence measurements. In this paper, the techniques to use the predicted final surface movements and deformations for assessing their influence on the integrity and functionality of highway structures (e.g., road surface pavements, concrete slabs, transverse joints, etc.), vehicle dynamics, comfort level, and drivability are presented. A number of mitigation measures to protect the highway structures and to ensure traffic safety are proposed along with an application case.

By Yi Luo, Jian Yang, Hua Jiang

Surface subsidence induced by underground coal mining activities, especially longwall mining operations, can cause various problems to interstate highways ranging from structural integrity, drivability to safety. Accurate subsidence prediction, correct influence assessments, and effective mitigation measures are the keys to ensure the safety of highway traffic. The surface subsidence prediction program, called comprehensive and integrated subsidence prediction model (CISPM), was developed based on the principle of influence function method and has been validated with a large number of subsidence measurements. In this paper, the techniques to use the predicted final surface movements and deformations for assessing their influence on the integrity and functionality of highway structures (e.g., road surface pavements, concrete slabs, transverse joints, etc.), vehicle dynamics, comfort level, and drivability are presented. A number of mitigation measures to protect the highway structures and to ensure traffic safety are proposed along with an application case.

By Nikhil Dhawan, Shrey Agrawal, Veeranjaneyulu Rayapudi

India’s steel vision of 2030 requires a huge amount of quality iron ore. The utilization of low-grade iron ores such as banded iron ores will play an important role to achieve the same production. The absence of alumina impurities in the banded hematite jasper (BHJ) ore provides it an edge over other low-grade iron ores. The conventional beneficiation techniques such as magnetic separation and washing were found to be ineffective to produce suitable feed (Fe ~ 60%) for the blast furnace. It was found that microwave exposure provides significant enrichment to the low-grade iron ore and can be used as a pretreatment step in the beneficiation of similar low-grade iron ores. The above study reveals that hematite phase is susceptible to microwave exposure which enhances the separation of iron values from impurities. Under optimum conditions, an iron-enriched concentrate with 61% Fe, 85% Fe recovery at 50% yield can be achieved from BHJ feed ~ 38% Fe. The pretreatment process for BHJ beneficiation includes only microwave exposure without any chemical additive and may prove economical and industrially feasible.

By F. W. DeVries, O. B. Mathre

Addition of Kastone® peroxygen compound and formaldehyde to cyanide gold extraction process effluents, containing at least 5 mg soluble copper per liter, will oxidize acid-dissociable cyanide to levels less than 0.2 mg per liter, without appreciable oxidation of thiocyanate. Most of the copper precipitates and is removed by filtration of the treated solutions. The treatment can be completed in less than 2 hours when the excess of hydrogen peroxide over the cyanide is about 75-100 mg per liter. The excess hydrogen peroxide destroys residual formaldehyde and then is catalytically decomposed by the copper-containing solids that separate, so it will not interfere with subsequent operation. A pilot plant using this technology has been operated for more than four months at rates from 1-2 gpm. Clear, filtered effluent containing less than 0.2 mg acid-dissociable cyanide per liter has been produced.

Jan 1, 1981

By Wayne Trudel, Eric Saderhold, Lloyd McEvers, Lori Clarke, Charles Lynn Bolin, Leroy Schutz

Editor’s note: This is the second part of a two-part series on how mine geologists added about 141t (4.53 million oz) at Newmont Mining’s gold operations in Nevada during 2003. Part one (ME, July2004, pp. 19-26) showed how cross-functional teamwork among mine geologists, engineers, metallurgists and operators added $65 million in revenues at Newmont’s Gold Quarry Mine. Part two deals with how this same cross-functional team added about 25.8 t (830,000 oz) of gold reserves and two years of life at the company’s LoneTree Mine. This was done through improved reconciliation methods, pit optimization designs and updated geotechnical parameters. Part two also discusses how Newmont’s Nevada mine personnel added about 62.2 t (2 million oz) of gold reserves at its Twin Creeks Mine, extending the mine’s life by several years. The Lone Tree Mine is a sediment-hosted, micron gold deposit. It is dominantly situated in the Golconda thrust footwall. The north-south trending Wayne Zone fault controls the highest-grade ores and

Jan 1, 2004

By Robert A. Cummings, Madan M. Singh

In April 1984 a subsidence depression formed directly beneath a two-story frame residence, near Linton, IN, causing 2 ft of separation between the floor and walls, and damaging both the foundation and interior of the building. The Office of Surface Mining undertook the rehabilitation of the area under its emergency response program. This paper describes the investigation performed to determine the cause, severity, and extent of the problem. Abandoned mine workings were found approximately 55 to 60 ft below the house. Based on the findings, remedial measures were prescribed. An abatement program consisting of grouting the mine voids was recommended, and specifications prepared. These were implemented, and the area has been successfully stabilized.

Jan 1, 1986

By T. Wang

A new generated NaNO3 ? NaNO2 ? KNO3 ternary thermal energy storage system which has low melting point as 124°C and high specific heat capacity was studied for the short and long?term thermal stability by using the Thermogravimetric Analyzer (TGA). Based on the actual working condition of molten salt in solar two, the simulated cyclic thermal stability measurement was also conducted. The ternary system demonstrates excellent short ? term thermal stability and thermal reliability after cyclic heating and cooling processes. However, in the long ? term as well as the simulated cyclic stability measurement, large amount of weight loss was observed. Moreover, the stepwise long ? term isothermal study reveals that below 440°C the weight change is minimal and this temperature is viewed as the upper limit temperature of thermal stability for this ternary system. To determine the lost phases at high temperature above the upper thermal stability limit, techniques such as XRD and SEM are used to compare the condition of the salt mixture before and after the long ? term thermal stability study. On the basis of the comparison, it can be concluded that the major weight loss was due to the decomposition of sodium nitrite.

Jan 1, 2012

By Paul Richardson

This paper will review several projects completed during the period from 1976 through 1984 which have been carried out utilizing big hole drilling concepts. The projects discussed will be from various industries to demonstrate the extent that big hole drilling methods are being used along with the current state of development. There will be a discussion of projects planned for the future where big hole drilling methods are the only technology being considered. Also included in the discussions will be an overview of the most recently completed heavy oil recovery project. During the next decade, big hole drilling methods will be used more and more in all industries where underground access is required. The safety, speed and economics associated with shaft sinking using drilling methods are becoming more and more recognized and the technology is rapidly becoming an accepted shaft sinking method.

Jan 1, 1985

By Wilfred P. Schmoe

Introduction An integrated oil company has two options in approaching strategic planning. It has to decide whether it is in business for the long-term. I state this in all seriousness. Those who help manage public companies have the responsibility of good stewardship of other people's money. We must decide whether continued investment in our basic business will generate a reasonable rate of return. With a world surplus of petroleum production capacity, and continuing downward pressure on prices, this question should be addressed by all oil companies. And a positive answer is not necessarily a foregone conclusion in all cases. The decision should be made based on proven competence in finding and developing petroleum reserves on a cost-competitive basis with other producers, and on a frank analysis of future prospects. This should include a realistic assessment of the projected rate of return on specific investment projects. If a company did not pass these tests, its strategy could take one of four paths. Diversification First, it could diversify. But recent history suggests that oil companies are not good at managing other businesses. Second, it could seek a buyer for its business at the optimum return for its owners. Third, it could sell its assets on a piecemeal basis. And, fourth, it could adopt a longer-range plan of self-liquidation by living off current recoverable reserves. In other words, by not investing in exploration and development, it could maximize short-term profit and pass the money back to shareholders in the form of dividends. The Conoco component of DuPont has a below-average cost of finding petroleum, a good track record of efficient production, and a full plate of projects that pass the test of return-on-investment. In short, Conoco is in business for the long-term. That fact, in itself, determines at least one key element in strategy. This is to extend the life of the petroleum reserve base while at the same time maintaining maximum efficient rates of production to provide a strong cash flow. A company that is able to maintain a strong reserve base will ultimately see the value of those reserves escalate as world oil supplies tighten. Our planners expect this tightening to occur within the next decade as demand grows and production in non-OPEC areas of the world begins to decline. An exploration program tailored to meet the requirements of reserve replacement and current production should have two basic parts. The first is relatively low-risk exploration in proven oil provinces. This is augmented by

Jan 6, 1985

By E. Stiakakis

The paper presents a geotechnical simulation of the "Mavropigi" open pit mine (Western Macedonia Lignite Center, Greece), using the finite element method. The simulation was based on the initial planning of the pit using Mohr-Coulomb and Soil Hardening models. Results indicate high stability factors as well as the magnitude of the expected horizontal displacements and floor heaving. However, these deformations do not influence decisively the overall stability unless locally adverse tectonics are encountered. Results can be used in the ongoing update of mine planning and stability evaluation.

Jan 1, 2006

By Y. Q. Zhang, S. S. Peng

Numerical modeling was used to design the pillars and bolting plan for a mine with weak roof and multi-seam stress condition. Previous mining experience, pillar/roof yielding and in-situ horizontal stress were considered in the models. By modeling the upper seam yielding and vertical stress transfer, a multi-seam influence zone was obtained. Appropriate pillar sizes were designed for conditions with and without upper seam stress influences. Roof support for the track and belt entries, using fully-grouted resin bolts and cable bolts, was proposed and implemented in the model. The bolting plan was evaluated under the weak roof condition.

Jan 1, 2004

By M. T. Ansari

"This article explains the ways in which investment on mining infrastructure is a geopolitical issue. It discusses the effect of installing sufficient infra structure to get the product to the world market, and argues that there is a risk involved in depending on traditional suppliers who wish to invest in the infrastructure. It explains how to make a distinction between dedicated purpose infrastructure and general use infrastructure by examining the positions of the main actors in mining projects. It argues that these positions can not be understood as analogous to projects in developed countries. To conclude, infrastructure is a crucial link in the supply chain to market but the relative size of such projects in relation to the economy means that investors decisions in developing countries have quite different implications from those in developed countries."

Jan 1, 2011

By G. Bee, Z. Gavelan, R. Espinel, Y. Roditis, X. Ochoa

In August 1996 Barrick Gold Corporation acquired the Pierina property, an advanced stage exploration project, high in the Andean Cordillera of Peru and in November 1998, in a record time of just over two years, poured the first gold. After more than three years of a very successful operation at some of the lowest operating costs in the world, this presentation serves to briefly describe the project through design, construction and start-up and in particular to spotlight some of the challenges that have been overcome in valley heap leaching in a high rainfall, alpine setting.

Jan 1, 2002

By G. A. Grandy, P. F. Thomas, C. D. Danecki

When considering the mill drive system for a grinding application, a large number of questions must be answered. Depending on the mill size and type, the mill can be driven by several configurations of drive systems: a single low-speed motor connected to a pinion driving a ring gear, two low-speed motors connected to two pinions and driving a ring gear, or a gearless motor mounted directly. In addition, a gear drive system can have a reducer placed between a high-speed motor(s) and pinion(s) or a power path splitting pinion stand. In some designs the reducer is integral with the pinion stand driven by a high-speed motor. The technical and commercial implications of several mill drive options are presented. Initial cost, cost of installation, cost of commissioning, and cost of operation and maintenance are presented for each drive option considered. The impact of each drive system on the design, cost and operation of the overall plant electrical system is discussed. Also, consideration is given to mill drive availability, and the potential cost resulting from delays in plant production.

Jan 1, 2001

By Yousef Ghorbani, Abolfazl Danesh, Fatemeh Kazemi, Ataallah Bahrami, Morteza Abdollahi, Mohammad Raouf Hosseini

This study aims to investigate the effects of operational variables on concentrate grade, recovery, separation efficiency, and kinetic parameters of the copper flotation process. For this purpose, the effects of the pulp solids content, collector and frother dosage, and preparation and concentrate collection time were studied using a Taguchi experimental design. The results of statistical analyses indicated that the concentrate collection time and pulp density were the most influential parameters on concentrate grade. Considering copper recovery, concentrate collection time, collector dosage, and pulp density were the most significant variables, in decreasing order of importance. Also, the separation efficiency was mostly influenced by the concentrate collection time. Furthermore, kinetic studies showed that the second-order rectangular distribution model perfectly matched the experimental flotation data. The highest kinetic constant of 0.0756 s−1 was obtained from the test, which was performed with 35% solids content and 40 and 20 g/t collector and frother, respectively. The highest predicted copper recovery of 99.57% was obtained from the test at 30% solids content, and the collector and frother dosages of 40 and 15 g/t, respectively