Search Documents

By J. A. Finch, B. J. Huls

Accurate level detection is required to make full use of level in optimizing control strategies for flotation columns. Techniques based on pressure and electrical conductivity are compared. Pressure and conductivity profiles give good agreement on level. Level calculated from single and multiple pressure values became more accurate using, in order, one, two and three sensor locations. The level estimate remained in error, however, because, unlike the collection zone, froth zone bulk density varies with height. A conductivity probe continually updating the conductance profile is a practical method of obtaining an accurate level.

Jan 1, 1990

By K. L. Bickel

Catalyzed diesel particulate filters (CDPFs) are used for reducing diesel particulate matter (DPM) concentrations in underground mines. The U.S. Bureau of Mines is conducting research on how catalyzed diesel particulate filters perform. Two CDPFs, with two different catalysts, are used on vehicles in two mines. The CDPFs are periodically removed from service and evaluated in the laboratory to determine their DPM collection efficiency, regeneration temperature, and effects on gaseous hydrocarbon (HC) and carbon monoxide (CO) emissions. This report summarizes the results of the laboratory evaluation, and the mines' experience with the CDPFs. Both CDPFs have operated over 2,000 h. One was evaluated after 1,646 h; its collection efficiency at one operating condition was 87.3 pct. After 2,135 h of operation it was removed from service because it was damaged. The second CDPF continues to be used after 2,328 h of service. The laboratory evaluation indicated its collection efficiency decreased after 1,584 h of use and its regeneration temperature increased from 405' C to 420' C. The mines' experiences with the two CDPFs varied. While being used on mine vehicles, both CDPFs became plugged with DPM on a number of occasions because of insufficient regeneration. CDPFs are capable of lowering DPM concentrations in diesel exhaust. They can also lower emissions of CO and HC, depending on the type of catalyst used. In this study, the performance of the CDPFs changed with use. Recommendations are given in this report for proper use of CDPFs in mines.

Jan 1, 1994

By T. O. Kuhl

The Royal-Mountain King Project is 7.2 kilometers (4.5 miles) northwest of Copperopolis, California. Reserves of 8,250,000 t (9,100,000 st) at 2.32 g/t (0.068 oz/st) gold will be processed at 2500 t/d (2750 st/d) from three pits. Production is scheduled to begin the first quarter of 1989. District geology consists of northwest trending sequences of Jurassic meta-sedimentary and meta-volcanic rocks. Three ore bodies are located along the Hodson fault which trends northwest and dips 40 degrees northeast. The Gold Knoll and North Pit ore bodies are hosted in carbonate and silica altered meta-volcanic rocks whereas the Skyrocket ore body is hosted in quartz stockwork zones in meta-sedimentary rocks. Gold is present as inclusions and micro-veinlets in pyrite.

Jan 1, 1989

By Rolando V. Cuaño

For geostatistical applications, heterogeneous spatial phenomena are better modeled as mixtures of populations. However, the modeling of the constituent populations can become complex. The alternative mixture model offers a simplified approach to the w modeling problem. The model is applied and tested on the Walker Lake data set. Compared to the univariate ordinary kriging model, the alternative model generates less biased block estimates.

Jan 1, 1996

By S. D. Thompson, L. Adler

This study reviews and analyzes the empirical methods available for designing the capacities of coal mine gathering belts. The analyses lead to recommendations concerning the application and implementation of each empirical method. Operations research techniques, mainly simulation models, are also briefly mentioned, and a few recommendations are made concerning their selection and application. The objective of the study is to provide a reliable basis for the practicing engineer to properly select, apply, and implement a capacity design method.

Jan 1, 1988

By Thomas E. Newman

This paper is a case study using new laser-terrain-mapping technology by EagleScan, Inc., for creating topographic maps. Holnam, Inc., has used this technology to create maps and volumetric calculations of several mines in the United States. The information is superior to conventional methods through accuracy, manpower, time, and cost. Holnam, Inc., was the first cement manufacturer to use the Digital Airborne Topographic Imaging System (DATIS?). The technology uses the DATIS? to produce high-resolution terrain maps and volumetric assessments of any area. DATIS? is a mapping instrument that integrates (1) a Light Detection and Ranging (LIDAR) instrument to measure terrain elevation using laser light, (2) a large-format digital camera, (3) a relative position Global Positioning System (GPS) to measure aircraft position, and (4) an Inertial Measurement Unit (IMU) to measure aircraft attitude. The DATIS? can measure up to 220,000 elevation samples per mil. The system continually collects data on the aircraft's position and measures the time for each laser pulse transmission to return from the ground, giving each sample a GPS reference. The system can operate at night, in overcast sky, and during high-wind conditions and can measure terrain below vegetation cover, unlike standard aerial photography used for traditional surveying and mapping. Surveyed ground-control panels are no longer necessary with this new technology, and only one ground GPS base station located within 60 mi from the aircraft position is required. A computer elevation-point data file is created with the x, y, z coordinates of each laser elevation sample. With this file, CAD engineering programs can create topographic maps that rival products using conventional aerial mapping techniques. Volumetric measurements of stockpiles and pits are also available due to the high density of points collected from an area. This new technology radically changes the turnaround time for map users, giving a product in the format used by today's cartographers. The time line from flight to maps is measured in days instead of weeks.

Jan 1, 1999

By Kotaro Ohga, Kiyoshi Higuchi

In our laboratory, a new detection system using smell detectors was developed to detect the spontaneous combustion of coal and the combustion of other materials used underground. Laboratory experiments were carried out on several kinds of coals, including South African coals, and machine oil, wood and rubber used in belt conveyers. The following results were obtained: 1) Spontaneous combustion of coal can be detected earlier by smell detectors than by conventional CO detection methods. 2) There were no differences in the results using different kinds of coal. 3) Combustion of other materials can also be detected earlier by this system than by conventional detectors for gas and smoke. 4) Use of this detection system enables one to discern the source of the combustion gases, whether it be coal, wood, oil or rubber.

Jan 1, 1995

By Kuda R. Mutama, Allen E. Hall

A wind tunnel investigation into the fundamental characteristics of jet fan performance is described. The effects of varying fan positioning in a square tunnel cross section are reported for two fan outlet diameters and velocities. Tests were conducted, also for a jet fan placed in a flow developed by an external fan operating in the same direction as the jet fan. The position of the jet fan relative to the tunnel walls was found to affect its performance. Performance parameters were determined and used to formulate theoretical equations based on momentum and energy considerations. The results identified a range of flow ratios which can be used to design an effective jet fan ventilation system and provide a basis for the selection of jet fans for practical mining applications

Jan 1, 1997

By Karan S. Keith, Haydn H. Murray

The sorptive and impervious nature of clay materials was recognized long before modem technology allowed us to understand the physiochemistry of clays. In Cyprus, around 5000 BC, sorbent clays were used for fulling woolen cloth. One of the earliest recorded uses of clays as an impervious liner was more than 3200 years ago in the construction of a bitumen-sand-gravel-clay liner built along the embankment of the Tigris River at Assur. Today one of the most common applications for clay minerals in the environmental industry is for use as impermeable barriers to fluid transport. Clay minerals are fine in particle size and thus have large surface areas, which, as a result of intermolecular forces and ionic substitutions, make them excellent materials for both ion exchange and ion sorption. Therefore it was logical to consider certain clay materials for applications in the environmental industry, where they can act as physical and chemical traps for potential contaminants. Certain bentonites have historically been used as sealants for fluids (Grim, 1962), and other clays have been used as sorbents for both water and oil (Haden, Jr., 1972). Prior to the 1980s, disposal of the nation's municipal, commercial, chemical, and nuclear wastes was largely indiscriminate and poorly regulated. This created environmental pollution problems, especially with respect to groundwater contamination. Promulgation of federal regulations like the Resource Conservation and Recovery Act (RCRA) and the Comprehensive Environmental Response, Compensation and Liability Act (CERCLA - commonly known as Superfund) have forced a more careful and costly approach to waste disposal. The US Environmental Protection Agency (EPA) is the government body charged with enforcing and ensuring compliance with federal regulations governing toxic waste production, storage, and disposal. Widespread application of geotechnology to the design and construction of waste containment systems and to pollution remediation has become necessary due to such laws and because of increasing use of the subsurface environment for the disposal of hazardous wastes. In the United States nearly 1.8 kg of trash is disposed of per person per day, which amounts to nearly 181 Mt per year. This amount is more than double the waste produced in 1960, and these numbers are expected to continue to increase. Canada produces approximately 1.68 kg of waste per person per day. The EPA estimates that in the United States 64% of our garbage is landfilled, 18% recycled, and 18% incinerated. Even with continued increases in recycling and incineration efforts, the EPA projects that the United States will still need 82% of today's landfill capacity in the year 2000. Data on the exact number of landfills in the United States and Canada is conflicting in part because of changing definitions of what constitutes a landfill and because of inadequate record- keeping by some states and provinces. An estimate of the number of municipal solid waste (MSW) landfills in the United States in 1990 to 1991 ranged from 4 462 to 10 467 with an average estimate of 6 600. In Canada the number of MSW landfills reported varied from 5 493 in a 1982 survey to 1 766 reported in a 1991 National Solid Wastes Management Association (NSWMA) survey (Repa and Sheets, 1992b). A properly operated MSW landfill on average requires 1 hectare of land per year per 25 000 people (Coates, 198 1). In addition to MSW facilities, there are also waste disposal facilities needed for hazardous waste and low level and high level radioactive waste. In 1983, approximately 266 Mt of hazardous waste was generated in the United States, almost 50% of this by industrial production. About 68% of the hazardous waste generated in the United States and Canada and almost 50% generated in Europe are still landfilled (Egger, 1987). In 1985, approximately 51 000 m3 of commercially produced low level radioactive waste was disposed of in radioactive waste disposal sites across the United States (Jungling and Greeves, 1989). By 1987, the US defense program had produced approximately 10 000 t of high level nuclear waste. In addition, there were approximately 14 000 t of spent fuel assemblies from commercial nuclear power plants in temporary storage; the amount is expected to nearly triple by the year 2000. Presently most commercial spent fuel assemblies are stored in water-filled pools at nuclear power plants. Defense waste is stored on federal reservations in surface and underground steel tanks (Anon., 1987). Under federal law nearly all waste disposal and containment sites are required to have a liner or barrier and a cover system design that meets federal- or state-approved hydraulic conductivity requirements for the type of waste that the site will receive. When approved materials, necessary for constructing the waste containment structure, are not available on site, one of the most economical ways to meet these requirements is through the use of clay, soil/clay, or clay/geotextile materials. In a 1991 survey by NSWMA of its members and other select private sector facilities, 81% of the surveyed landfills had some type of liner system. About 75% of these liners were clay materials (either recompacted or natural). The remaining 30% were using flexible membrane liners as part of a liner system. Clay liner materials are most commonly used in the South, Midwest, West-central, and South-central regions of the United States. About 93% of the landfill facilities had closure plans, and of these 91 % were using clay materials in some way for the final cover material (Repa and Sheets, 1992a). Waste barriers and containment structures take several basic forms, and they are used in a variety of different applications: 1) cutoff walls, 2) soil or soil/clay-admix liners, 3) geosynthetic bentonite-clay/geotextile membranes, 4) radioactive waste containment barriers, and 5) synthetic geomembranes. This chapter will discuss the first four of these categories. The field of synthetic geomembranes, although a related topic, is beyond the scope of

Jan 1, 1994

By J. G. Groppo

Laboratory settling and filtration testing was conducted on wet processed fly ash in order to determine the applicability of conventional dewatering techniques to reduce the moisture content prior to drying. Settling tests showed that acceptable clarity (<1.5 g/l suspended solids) could be achieved after as little as 6 minutes of settling. After settling to a consistency of 40 weight % solids, continuous laboratory vacuum filtration testing produced a cake containing below 20% moisture with throughput exceeding 150 lb/ft2/hr.

Jan 1, 1997

By M. Dayne Aldridge

A description is given of an experimental ventilation control system designed, built, and tested by WVU under United States Bureau of Mines sponsorship. A description is given of the control, system used and the mine-wide microcomputer-based ventilation monitoring system used with it. Test results of experiments conducted with this system at Eastern Associated Coal Corporation&apos;s Federal No. 2 underground coal mine are presented. In addition, a brief description is given of a new microprocessor based system presently being tested.

Jan 1, 1980

This paper presents the latest developments in the flotation model being developed collaboratively between the Julius Kruttschnitt Mineral Research Centre in Brisbane, Australia, and the Mineral Processing Research Unit of the University of Cape Town in South Africa as part of the Australian Minerals Industries Research Association (AMIRA) P9 Project. It includes: - characterisation of flotation cells using the bubble surface area flux, Sb; - relationship of Sb to the overall flotation rate constant; - determination of the froth recovery factor; - evaluation of ore floatability; - modelling of entrainment - development of the Floatability Characterisation Test Rig (FCTR); - use of the model in design and optimization of flotation plants; and - current and future work.

Jan 1, 1999

By M. J. Virnig, B. D. Boley, G. A. Wolfe, J. M. W. Mackenzie

A flowsheet for the recovery of nickel and cobalt from laterite ores was developed. The flowsheet involves acid leaching followed by hydroxide precipitation of the metal values and then releaching of the hydroxide cake with ammonia. Investigations of the chemistry of extraction of nickel by LIX® 84-I and a developmental reagent, XI-84-IT, along with the physical properties of the organic phases are described. Based on these investigations, suggestions with regard to design of a solvent-extraction plant and operating conditions were made.

Jan 1, 2002

By J. P. Hanten, G. Ramadorai

This paper presents laboratory and pilot plant data on the removal of heavy metals and molybdenum from mining-milling waste water. Molybdenum is removed as an Fe-Mo precipitate by proper addition of ferric sulfate. Heavy metals are lowered by lime treatment. Solid-liquid separation was achieved in both cases by flotation techniques. The Lectroclear electrocoagulation-electroflotation process was used to achieve the desired degree of metals removal. Good correlation was obtained on the laboratory and pilot plant scales. A two-step process consisting of the sequential removal of molybdenum and heavy metals was tested successfully using a mobile pilot plant. Preliminary data on sludge characteristics was obtained and the feasibility of recycling the iron sludge for iron and molybdenum recovery was established on the laboratory scale.

Jan 1, 1987

By Eric K. Albert

Computer oriented simulation techniques can be effective in the design and analysis of complex mining systems. In fact, a number of computer software products are available for mine systems simulation. However, previous models have tended toward being either data-intensive and deterministic, or data-limited and highly stochastic. The need for a fully integrated package with a simplified user interface has never been more apparent. In this paper, the design of a surface mining simulation model documented in Albert (1986) is described. The basic features of the surface mining system and their counterparts in the simulation model are discussed. The methods and algorithms used to implement these subsystems are presented. Considerations of information management and software design are illustrated, especially as they apply to the application of the package by a mining engineer. An example is provided to demonstrate the concepts embodied in the model and to show how a surface mine is simulated from mine parameters.

Jan 1, 1989

By James E. Kolesar

An essential prerequisite to expanding the application of longwall mining techniques in the United States is the development of a better understanding of the mechanics of rock mass deformation near the mined seam, in the inter- burden and at the surface. The results of studies of this type will provide a basis for the development of empirical and/or numerical modeling techniques to predict the rock mass response to mining both near and far from the mined seam. This will lead to improved gate and panel design, resulting in maximum recovery, increased productivity, as well as provide a mechanism for assessing likely surface effects induced by long- wall mining. Presented here is the instrument plan to be used at Kitt Mine No. 1 in the study of rock mass response to two adjacent longwall panels.

Jan 1, 1982

By B. Govindarajan, T. C. Rao, M. Vanangamudi

The results obtained from hatch, flotation experiments on two coals were used to develop relationships between the recoveries of water and solids into the concentrate. When the recovery of non-ash material (RN) for any size fraction is plotted against a parameter X, defined as [x _ Amount of (W) recovered x Collector dosage (C)in the concentrate (cc)(kg/t)] a single "non-ash recovery curve" is obtained. Non-ash recovery curves thus obtained from different size fractions are used to get a unique "modified non-ash recovery curve" for a given coal, using the reduced efficiency curve concept. Similar observations have been noted in the case of recovery of ash material (RA) also. The amount of water recovered into the concentrate is plotted against a parameter "Water Recovery Factor (WRF)," defined as [WRF = T.F.(1+C)] where T is time (in sec) and F is frother dosage (in kg/t). Plotted in this form a characteristic water recovery curve, for a given coal is obtained that may be defined by the following equation: [W4=W_(1 pWRF-e] The above relationships have been verified against the experimental results obtained from three more coals and are found to give satisfactory predicted values.

Jan 1, 1992

By J. P. Golightly

The structure and occurrence of nickeliferous laterite profiles are described and explained in terms of mineral solubility and drainage conditions. Complete profiles, from top to bottom, include: limonite zone; nontronite or silica zone; and saprolite zone. The middle zone is present only where drainage is sufficiently slow to allow saturation conditions to build up with resulting quartz or smectite precipitation. This precipitation may occur in any climate at a water table or in tropical climates with a long dry season. The degree of serpentinization of the laterite parent rock is important in determining the nature of the saprolite zone. Unserpentinized peridotite produces saprolite ores with hard residual rock cores, nontronitic or amorphous saprolitic rims, and fracture fillings of garnierite and quartz. Ser-pentinites yield relatively homogeneous serpentine saprolite, with minimal quartz or garnierite.

Jan 1, 1979

By J. M. Mutmansky, B. Kolonja

A PC-based simulation model using the software packages SIMAN and CINEMA was developed to simulate and animate truck-shovel operations. The model is capable of simulating one mathematical dispatching strategy using linear and dynamic programming and six heuristic dispatching strategies. Data were collected from an actual operating mine through time studies and analysis of historical records. Statistical analyses were performed, and appropriate theoretical distributions were fitted for various time events in the truck-shovel cycle. The model was then applied to study overall impact of these dispatching strategies on constrained and unconstrained mine productivity. The simulation/animation model developed in this study seems to be an efficient planning tool for choosing optimal fleets and finding an optimal dispatching strategy to produce an equilibrium between the quality and quantity of production.

Jan 1, 1995

By L. Lichty, R Bhappu, R. Rowan, G. Ramadorai

Treatment of refractory gold ores containing arsenic have always presented a major problem in their processing to recover the contained precious metal values. The major difficulties are concerned with lower recoveries, production of hazardous fumes, effluents and residues. Because of&apos;these arsenic related problems, many otherwise economically attractive precious metal deposits and dumps all over the world are not exploited. In recent years, treatment processee for refractory gold ores and concentrates have been explored and a few commercial operations employing roasting or pressure leaching have resulted. Roasting has limitations due to environmental constraints related to off gases. Pressure leaching involving high temperatures (180% to 200%) and pressures (400 psi) is accompanied by high capital and operating costs. An alternate route to roasting for treating pyrite and arsenopyrite ores and concentrates ia the "lime-oxygen hydromet" process carried out at a moderate temperature (100%) and pressure (100 psi). A simplified process for treating such arsenic containing ores and concentrates utilizing low temperature and pressure oxidation is presented. This low cost treatment with compressed air and lime renders arsenic as an inert component in the residue, meeting all the requirements of the EPA Toxicity Test. The precious metal values are then extracted from the autoclaved residue by standard cyanidation. This paper discusses this new development.

Jan 1, 1990