Search Documents

By D. W. Leyshon

The fluidized solids technique for the calcination of phosphate rock has been well established for over 10 years. This paper is intended to review the recent performance of many of the Dorr-Oliver FluoSolids* calciners. In addition, design features of these three compartment refrac¬tory construction reactors will be described and a comparison made with fuel requirements for single compartment calcination. Also presented will be certain, aspects of the use of the rock including a discussion of non sulfate sulfur in the rock. A system is described for producing a blended mixture of calcined and uncalcined rock.

Jan 1, 1972

By Daniel A. Payne

For many years underground mining in the Sydney Coalfield has suffered from the effects of high horizontal stresses. It is only in the last 15 years that they have come to be recognized, understood, predicted and even avoided. This paper relates experiences in three coal mines in three different seams in the Sydney Coalfield. The effect of the direction of the principal horizontal stress on the direction of drivage of gate roads, access roadways and longwalls is described. Results of a monitoring program to measure the change of magnitude and direction of the principal horizontal stress in the gate roads as a result of longwall mining are also presented as well as the effect of the direction of principal horizontal stress on the shape of sandstone/gas outburst cavities.

Jan 1, 1998

By Alfred W. Eustes III

The first of a series on the evaluation of rock cutting tools, this paper discusses the results of full-scale laboratory drilling tests that compare the performances of several polycrystalline diamond cutter (PDC) coring bits. The tests were performed in welded tuff as part of a site characterization program. Number of cutters, size of cutters, air course design, and other parameters were evaluated as they affect penetration rate, but this paper focuses mainly on the relationships of torque vs. thrust (weight-on-bit), specific energy vs. penetration rate, and thrust vs. penetration rate. These relationships change in diagnostic ways according to bit type, bit condition, and type of welded tuff.

Jan 1, 1998

By C. W. Baxter

Eveleth taconite company was formed in 1963 to mine and beneficiate taconite on the Mesabi range of Minnesota. Its thunderbird mine is located midway between the cities of Eveleth and Virginia, Minnesota, and the crude ore is transported by rail to its Fairlane plant approximately ten miles to the south of the mine, "figure 1". As is implied by the names of the mine and plant, the ford motor company is the principal owner of Eveleth taconite company, with an 85% interest, Oglebay Norton company holds the remaining 15% interest and also is the managing agent.

Jan 1, 1972

By Rainer Antretter

The city of Garmisch-Partenkirchen in southern Germany is located at a main transit road to Tyrol in Austria and suffers of a very heavy traffic load. Therefore, the Kramertunnel as a by-pass tunnel is built to release/mitigate the traffic through the city centre. The 3,600 m long single tube road tunnel is designed with a parallel but smaller emergency tunnel and with cross passages, fitted with single- and doublesided emergency bays, a vent shaft, and an intermediate ceiling to separate fresh air supply from the road traffic. The tunnel, concrete lined along its entire length provided the challenge to find smart formwork solutions for quick set-up, repositioning, setup and pouring. Three particularly specific sections are discussed in this paper.

Jun 13, 2023

By Paul Dean Proctor

The known northern ore zones of the New Lead Belt of Southeast Missouri extend to the drainage divide between the Meramec River draining north and east and that of the Black River draining southward. Intensive geochemical studies related to the environmental impact of the new mining area have been carried out in the vicinity of some of the newly developed mines, mills and smelter complexes (Bolter,1970; Gale, et al, 1973; Wixson, et al, 1969, 1977). Other investigations have related to fringe studies of the Northern New Lead Belt and the possible additions of heavy metals to the surface waters, stream sediments and selected aquatic life (Proctor, et al, 1975, 1976). Similar studies have been completed in the Joplin area in the Tri-State district, and in the fringe area near Springfield, Missouri (Proctor, et al, 1974). A surface geochemical study is currently underway on the lead-zinc-copper-cobalt-nickel province near Fredericktown, Missouri (Proctor and Sinha, 1977). This report summarizes some of the distribution patterns of heavy metals in the waters, stream sediments and selected aquatic life in the Upper Meramec River drainage basin just north and west of the known northern portions of the New Lead Belt of Southeast Missouri. The region studied includes the site of the proposed and somewhat controversial Meramec Dam and the reservoir site behind it. Some 3905 km2 (1508 mi2) are included within the drainage basin of the Upper Meramec River. Six distinct drainage areas are included within the drainage basin; 1) a combined, lightly industrialized and farm area around Rolla and Salem, Missouri representing the Dry Fork drainage; 2) a primitive, mostly forested area with some farms and cattle rancheseast and north of Salem, Missouri comprising the Upper Meramec River

Jan 1, 1977

By Theodore Feldsher, Seung Han Kim, Mourad Attalla, John Roadifer, Chu-Chieh Jay Lin

Lifelines in seismic regions of the world seldom can escape crossing active faults. Cities in California have been mitigating this risk by constructing improved fault crossings. This paper discusses the analyses and design of the lining for a tunnel carrying a water conveyance pipeline through a fault that can potentially displace during a major earthquake event. The paper presents expected fault displacement, fault width and orientation respective to the tunnel, characterization of the ground surrounding the tunnel and its interaction with the lining, and performance required of the lining. Several other fault crossings will also be presented and discussed

Dec 1, 2022

By C. Beul, R. Schipper, L. Santisteban

The Garfield Mine is a legacy vanadium mine in western Colorado with multiple mine openings, waste rock piles, and adit seepages that Cyprus Climax Metals Company (a Freeport-McMoRan Inc. subsidiary) voluntarily remediated through the Colorado Voluntary Cleanup Program (VCUP). The process to obtain a No Further Action determination from the VCUP is presented. Water treatment of the adit discharge, which is not part of the VCUP, is also presented. The remedial action objectives (RAOs) included preventing direct human or biotic exposure to the waste rock and radiation emitting from the waste rock; reducing metal concentrations and radionuclide activities in adit discharge and keeping the discharge from leaving the site; maintaining the existing undeveloped character of the surrounding landscape; and eliminating the need for a stormwater permit. The design included regrading, installation of an infiltration barrier and rock cover, a diversion channel, and a biologically based passive remediation water treatment system. An initial lab-scale evaluation provided design criteria for the full-scale system, which consists of a sulfate-reducing biochemical reactor and post-treatment aerobic polishing cells. The system has been operational since construction was completed in late 2016. Results indicate that the treatment objective of 90% bulk removal of constituents of potential concern (COPCs) is largely being met. The system also provides year-round operation and non-point discharge of effluent. After 20 plus years of site investigations, the remedial action was completed in 2016 with all RAOs met and a No Further Action determination granted in 2018. INTRODUCTION The Garfield Mine is a legacy vanadium mine located approximately 11 miles north-northeast of Rifle, in Garfield County, Colorado. It was leased and operated intermittently from 1929 to 1975 but was never operated by Cyprus Climax Metals Company (Cyprus) (a Freeport-McMoRan Inc. subsidiary). Prior to reclamation, site features included: • six mine openings—five adits and a vertical opening; • two adits discharging mining-influenced water (MIW)— Adit 1 at less than 4 liters per minute (L/min) and Adit 2 at 7 to 10 L/min; • main waste rock pile (13,500 m3) and small waste rock pile (minimal volume); • debris (small structure, mattress, bottles, shells, etc.) indicating site used for recreational purposes; and, • unimproved road, which has been used to access forest fires.

Jan 1, 2019

By R. H. Parker, B. A. Wills, D. G. Binns

Introduction With the increasing need to mine lower grade ores, high energy-related costs in comminution are of major concern. Very fine grinding is needed to liberate the fine mineral particles in these ores. Not only is this expensive, but it leads to greater losses in slimes. Gravity concentration techniques become unacceptably inefficient for particle treatment below 25 to 50 µm, and even flotation fails in the ultra-fine range. Ore from the South Crofty mine near Redruth, Cornwall, was subjected to thermal pretreatment in the hope that differential thermal expansion of the minerals would lead to intergranular cracking, and thus enhanced liberation. South Crofty ore contains about 1% tin as cassiterite associated with a complex assemblage of quartz, chlorite, tourmaline, and hema¬tite in granite and slate. Recovery of cassiterite can be as low as 70%, as overgrinding occurs during stage reduction of the material to 1 mm (primary grinding) and 180 µm (regrinding). Cassiterite is present in grain sizes ranging from submicroscopic to + 10 mm, the bulk being predominantly in the range of 50 µm to 3 mm. Experimental Flat polished sections of the ore were photographed in reflected light using a Vickers M17 microscope. The sections were then heated in a Carbolite LMF4 muffle furnace. The heating rate and temperature were monitored by a thermocouple immersed in the bed of particles. Previous work by Sherring (1981) on the same material showed that a 55% reduction in grinding resistance occurred when the material was rapidly heated and cooled through the quartz inversion tem¬perature (573°C), where a volumetric expansion of 0.86% occurs. The samples were therefore heated to 650°C at 26°/min, and were then water-quenched to room temperature. The effect of heat treatment on the mineralogy and fracture network was assessed by examining the same area after treatment. Results Most of the sections examined showed that extensive transgranular cracking occurred as a result of heat treatment. Such cracking, although weakening the rock and hence reducing the work index, would in no way enhance the liberation of the cassiterite from the host minerals. Intergranular cracking, which would lead to enhanced liberation, was difficult to discern under reflected light, but there was evidence of such cracking in some of the sections examined. Figures 1 and 2 are examples of typical sections before and after heat treatment. Figures la and lb - show cassiterite in hematite, Fig. lb, in normal incident illumination, illustrating clearly that after heat treatment, transgranular fracture is evident in the cassiterite. If any intergranular cracking has occurred, it is not evident in this photograph. Figures 2a and 2b show cassiterite in quartz before and after treatment. Fracturing in both minerals after treatment can clearly be seen, and there is evidence of intergranular fracturing. However, protruding "arms" of cassiterite are severed by transgranular fracture. Subgrains of quartz have also been isolated by trans¬granular fracture. There is major transgranular cracking across the wider sections of cassiterite. Discussion The effect of rapidly heating South Crofty tin ore to 650°C, followed by water-quenching to room temperature, has been studied by observing the fracture networks in mineral grains. The choice of 650°C as the heating temperature was influenced by the work of Sherring (1981), who found considerable reduction in grinding resistance after thermal pretreatment of the same ore. Scheding et al. (1981), however, have shown, by means of a crude calculation, that heat treatment cannot be justified solely on the basis of reduced grinding costs. The cost of heat treatment far out-weighs that of grinding, resulting in the combined costs for heat treatment being over six times that for grinding unheated material. The most economically attractive aspect of heat treatment is the possibility of enhanced liberation of the valuable mineral due to increased intergranular rather than transgranular fracture. Grinding costs would be greatly reduced by improved liberation at coarser sizes, and the costs of ancillary processes, such as dewatering and tailings disposal, would be reduced. The most significant economic effect, however, would be in improved metallurgical efficiency. Improved liberation would increase concentrate grades, and recoveries would be higher, particularly in the case of ores where high slime losses are produced due to the excessively fine grinding required to produce adequate liberation. Manser (1983) has shown that only a 1% increase in tin recovery, at the same concentrate grade, would be sufficient to offset heat treatment costs on South Crofty ore. Heavy liquid analysis and shaking table separation have been used to evaluate the effect of thermal treatment on processing (Binns, 1984; Scheding, 1981; Sherring, 1981). However, treatment of unheated and heated samples of South Crofty ore, ground to the same product size, by such methods have shown little evidence of improved metallurgical efficiency after thermal pretreatment. The large amount of transgranular fracturing revealed by reflected light studies helps to explain this lack of improvement. Nevertheless, from the evidence of some of the fracture work, it is surprising that no improvements in metallurgical

Jan 1, 1988

By Guillermo V. Borquez

The economics of open pit mine design are dictated by three basic elements: cut-off grade, stripping ratio and slope angle. Although these elements are functions of a number of independent parameters, they are interrelated through their influence on the overall economics. The optimum slope angle is the most uncertain element to determine, because rock mass properties are difficult to obtain. However, for preliminary estimation, the slope angle can be determined from the relationship between the probability of failure and the safety factor. The economics of the slope selected will depend on a profit versus risk judgment. In this paper, the author will present an actual case of application of this postulate.

Jan 1, 1977

By K. N. Han

Coal is becoming increasingly important as a major energy source in the face of the world's depleting energy mainly based on oil reserves. Coal is by far the most abundant fossil fuel both in the United States and abroad. Currently, because of increased mine mechanization, the fineness of preparation plant feed is increasing. Further, in the future as the grade of coal diminishes and the sulfur content increases, upgrading preparation of coal is very important. Because the density of coal is less than that of rock materials that occur as impurities, coal is separated from such waste largely by gravity-controlled processes for particle size between 5 inches and 28 mesh. If the size of coal particles is below 28 mesh, froth flotation is a good method for upgrading fine coal. Previously, numerous investigators have tried to upgrade coal values by froth flotation(1-16) and have achieved moderate success. However, the recovery and grade of coals in the concentrates are not always satisfactory, especially when the particle size is small. In general, when the size of coal is below 100 mesh, the above methods suffer from poor grade and low recovery. The reason for this is that as size decreases, the effects of gravity diminish, and other forces take effect.

Jan 1, 1985

By R. Mensah-Biney

The kinetics of gold-bromide loading onto activated carbon has been investigated in a batch stirred reactor. The amount of gold adsorbed by the carbon was correlated with time based on a second-order equation. The rate constant for gold-bromide species onto activated carbon ranged from 0.27 to 1.2 x 10-3 (kg/t)-l(min)-l from a solution containing 25 ppm of Au, with 0.8 g carbon per liter of solution at 30° C. The equilibrium saturation capacity (Q.) was 36±3.0 kg/t from the same system. The rate of loading increased with decreasing particle size, decreasing pH, increasing temperature, and decreasing concentration of gold in solution. The calculated activation energy E. was 8.8 kcal/mole, significantly higher than those reported for physical adsorption. The equilibrium saturation capacity (Q.) increased with increasing concentration of gold in solution, but was independent of other variables such as temperature, agitation speed, particle size and pH. These rate constants and equilibrium saturation capacity for the gold-bromide species are higher than those reported for the gold-cyanide systems.

Jan 1, 1996

By J. Herbst, J. Groppo, A. Noble, R. Q. Honaker

"Coal and coal byproducts produced annually contain enough rare earth elements (REEs) to meet current U.S. demand. The REEs exist in the form of minerals, ion-exchanged elements associated with clays and chemically bonded elements within the organic coal matrix. Researchers at three universities have collaborated to evaluate the effectiveness of existing physical and chemical concentration processes for the recovery of the REEs. The efforts have found that physical separation processes can increase the total REE content in the thickener underflow material collected from a Central Appalachian coal cleaning facility from around 300 ppm to values greater than 17,500 ppm on an ash basis. On the other hand, leaching was effective in recovering REEs from coarse middlings materials collected from multiple coal basins as indicated by recovery values exceeding 80%. Based on material characterization data and process evaluations conducted for several potential feed coal sources, economic recovery of the REEs will require byproduct production of both clean coal and REE concentrate using a process flowsheet that is unique for each source. INTRODUCTION Recent studies initiated by NETL showed that U.S. coals contain significant amounts of rare earth elements (REEs), suggesting that rare earth minerals (REMs) and/or REEs can be produced as byproducts [1]. According to the report, the richest source of REEs is the Central Appalachian coal. At present, there are 208 coal preparation plants located in the region (WV, KY, PA, VA, AL, TN) with a capacity of 166,495 tons/hr or more than 1 billion tons annually [2]. If only a portion of these plants are retrofitted with advanced separation processes, the U.S. coal industry can become a significant producer of RE minerals as byproducts. An inherent advantage of becoming a byproduct producer of REEs is that no mining cost needs to be part of the product cost. Other researchers have also shown that coal can be a significant source of REEs. The average sum of the rare earth plus yttrium (REY) concentration of the world coal is approximately 68.5 ppm, which is lower than the corresponding upper crustal concentration (UCC) (168.4 ppm). However, the average REY content of the mineral matter in the world (404 ppm) and U.S. coals (517 ppm) are 3 times higher than the average UCC. Some of the mineral matter in Russian and Chinese coals have REY concentrations in the range of 0.68 to 2.03% and contain a better source of higher value REYs than many primary rare earth deposits [3]."

Jan 1, 2017

By P. E. Lenz

In Nevada, large deposits of diatomite were formed during the Miocene / Pliocene in deep, alkaline lakes. Associated sediments are predominately fine-grained lacustrine with varying fluvial-clastic layers. Tephra layers are common, and probably served as a source of soluble silica for the extensive diatom colonies. Four companies are currently producing diatomite from Nevada deposits. Nevada ranks second to California in annual domestic production. Nevada diatomite is used in filter aids, fillers, absorbents, catalyst supports, and many other products. Economics and mineral reserves indicate that diatomite production in Nevada will be significant well into the next century.

Jan 1, 1993

By C. Sun

The Leeville underground mine has been in operation since 2006 and currently produces 3,300 tons of ore per day with an average gold grade of 0.4 opt. The mine has a large horizontal extent of 2,500 feet by 500 feet and a vertical extent of 20 to 200 feet. Based on the characteristics of the ore bodies, the deposits are divided into several mining zones. The geotechnical properties of mining zones are also different from one zone to another. A successful geotechnical collection system is very important for the mining designs and operations in the Leeville underground mine.

Jan 1, 2010

By D. W. Gunkle

Processing of various ores and materials in a reducing atmosphere has been done for many years. However, the typical device currently used is a large, often high maintenance, expensive piece of equipment; the rotary kiln. While it is a very reliable and a proven technology, the rotary kiln also has its limitations. It is limited by its ability to process very fine materials without creating a huge dust loss to the air pollution control equipment. This leads us towards the development of an alternate technology; the Gas Suspension System. Gas suspension preheating of various materials has been in commercial use since the early 1950's, but recently has been expanded to include Gas Suspension Reduction. Laboratory experience has proven successful on several materials; Nickel Laterite Fines, Iron Ore Fines, Fluorspar, and Clays. The gas suspension reduction system has many advantages over the conventional reduction kiln when processing fines. They are; lower cost, more fuel efficient, able to process fines, less real estate required, etc.

Jan 1, 1998

By R. Benemelis

The existence of resins in some coal deposits in various parts of the world has been known for many years. These resins vary considerably in chemical structure and properties. The resin that is found in Utah coal, however, is rather unique, and has properties particularly attractive for the manufacture of printing ink mastics and adhesives. This resin is a rather dark, very high melting point, low molecular weight hydrocarbon resin. Its typical properties are shown in Table I. Its largest use by far, has been in the printing ink industry. The history of Utah coal resin is interesting, but unfortunately one of disappointment and failure.

Jan 1, 1990

By Kadri Dagdelen

The importance of factoring mining dilution into feasibility stage ore reserve estimates is discussed. An example that relates the issue of mining dilution to the size of smallest volumes that can be mined selectively is given. Relationship between the size of the selective mining units (SMU's) and the variance of their average grade is presented. The concept of variance reduction and its use in factoring mining dilution into geostatistical ore reserve estimation is described. An approach to estimate variance reduction factor by way of conditional simulation is introduced.

Jan 1, 1996

By G. A. Parkison

The sequential copper analysis method is a particularly useful technique to semi-quantitatively define the geologic, mineralogic, and metallurgical types and zonations commonly associated with porphyry-type copper deposits. The method is based on the partial dissolution behavior displayed by the prevalent copper minerals malachite, chrysocolla, chalcocite, and chalcopyrite to solutions containing sulfuric acid and sodium cyanide. Results from sequential analyses of the sample and analytical residue using sulfuric acid followed by sodium cyanide and then aqua regia solutions when compared with conventional total copper analyses can determine the amounts of leachable oxide minerals, leachable secondary sulfide minerals, and primary copper minerals, respectively. Sequential assay analytical results and interpretation are presented for copper deposits in Chile, Mexico, and the United States.

Jan 1, 1995

By M. W. Smith

Pennsylvania has 2500 miles of streams that do not meet water quality standards due to acid mine discharge (AMD), making AMD the greatest cause of water pollution in the state. The problem is mainly caused by abandoned coal mines. Pennsylvania is using a watershed-based approach to abating AMD which includes remining as a key component of a comprehensive restoration strategy. The Tangascootack Creek Watershed was targeted for AMD restoration through remining. Geologic mapping and overburden data were analyzed using Earth Vision software to identify areas of coal reserves which could be remined to improve water quality. Incentives are offered to encourage mining in these designated areas.

Jan 1, 1999