Search Documents

By Y. J. Zhang

This paper presents the results of a recent study on the development of an in-situ testing method for determining the coal strength in mine pillars. The strength testing is performed in the horizontal holes drilled into the coal rib using the penetrometer. It is a hydraulically powered device that uses an indenter to press the surface of the borehole until the load reaches the failure point of coal. The pressure and the penetration of the loading pin are recorded by the data acquisition unit. The results collected from several coal mines indicate that this testing method is ideally suited for the realistic coal strength measurements. The new testing system not only improves the accuracy of pillar strength determination, but it is more cost efficient than the conventional method.

Jan 1, 1995

By Sotiris N. Kamenopoulos, Zach Agioutantis

Rare earth elements (REEs) are considered critical minerals for industrial and defense sectors. REEs are not as rare as the word “rare” portrays; yet, the exploitable and/or profitable deposits of REEs may be found only in certain geographical areas. The political and social conditions characterizing these areas may not always be in favor of mining operations. These conditions are imposing the need for extra consideration on the geopolitical constraints prior to any decision-making and before any mining project begins. This study assesses the risk related to mining projects for areas that feature REE deposits based on a geopolitical viewpoint. Probable ranking differences between the current assessment and a 2015 assessment are discussed. The comparative indicators used and the appraisal procedure applied in this comparison are based on a number of different geopolitical indicators. Several ranking changes occurred between 2015 and 2019.

By Ricardo Oliveira Gallart de Menezes, Claudio Gerheim Porto, Reiner Neumann

The Jiboia heavy mineral sands deposit is a new discovery associated with the São Francisco River delta on the northern coast of Sergipe state. The identified resources are part of the much larger mineralized trend. Mineralization is hosted in paleodunes deposited on Holocene marine terraces (Fig. 1). The dunes are up to 30 m above sea level, and mineralization occur from 6 m above sea level upward. The main ore minerals constitute pseudorutile, ilmenite, zircon, rutile and monazite. This work presents a thorough characterization of the mineralogy and granulometric distribution of the Jiboia orebody.

Apr 1, 2024

By E. Farrokh

CSM and NTNU models are among the most commonly used models in TBM performance evaluation. Due to increasing application of TBM in different tunneling conditions, modification became necessary for these models. Sensitivity analyses on these two models indicate that both models are very sensitive to machine characteristics. Analyses performed on CSM database for cutter load and penetration rate prediction indicate while the r-square of the CSM model is reasonably high for the predicted cutterload, the r-square value for the penetration is low. In order to increase prediction capability of CSM model for penetration rate the model was reevaluated using non-dimensional analysis and the original database of Colorado school of mines. NTNU model is evaluated using Monte Carlo simulation and regression analysis. The results of analyses indicate that the majority of the variation of the penetration in NTNU model can be explained by only three parameters. This might indicate that the effects of other factors are overshadowed and it is worthy to reevaluate NTNU model using original database and more updated statistical methods to avoid overlapping of different parameters correlations.

Feb 23, 2014

By Sandeep Kumar Jeripotula, Govinda Raj Mandela, Aruna Manglapady

Dumper operators are frequently exposed to whole body vibration (WBV) in surface mines. Surface mining activities involve the amalgamation of comparatively high intensity of vibration and extended exposure durations. Efficient risk reduction mandates knowing of important phases of a task that poses a threat to health of dumper operators. So far in India very limited studies have been reported on WBV exposure with regard to surface mines. This paper evaluates WBV of dumper operators based on ISO 2631-1:1997 Standards and European Union (EU) Directive 2002 for different phases of job cycle. Six dumpers were considered for this study and the vibration measurements were made for all the four phases of the job cycle by placing the triaxial accelerometer on the operator’s seat-surface and at the seat-back, independently. The findings of the study revealed that the haulage task (loaded travel and empty travel) remains the chief contributor to vibration exposure according to seat-surface and seat-back measurements. Maximum frequency weighted root mean square (RMS) of 1.12 m/s2 and 1.09 m/s2 were reported for empty travel task for seat-surface and seat-back measurements, respectively. For seat-surface measurements based on RMS, Z axis remains as the dominant axis of vibration for all the dumpers during haulage task, whereas for seat-back measurements, the dominant axis varies between X and Y. Exposure action value (EAV) based on RMS has exceeded the threshold value of 0.5 m/s2 for all the dumpers during loaded travel and empty travel for seat-surface as well as for seat-back measurements.

By Siddhartha Roy, Hemant Agrawal, Ram Madhab Bhattacharjee, Devi Prasad Mishra

Heat stress is a major concern for the health, safety and productivity of miners working in hot and humid underground mines. At greater depth, heat inside underground mines increases due to geothermal gradient, heat released from high-capacity machinery, exposed rock surface, auto-compression of air, human metabolism, etc. Prolonged physical work in thermal environments severely affects the health, safety and efficiency of miners. In order to address this important issue, a systematic literature review (SLR) has been conducted. This SLR aimed to identify the research gap in the area of heat stress effect on underground miners and its control. An extensive literature search was carried out on numerous digital databases, grey literature and conference proceedings to identify relevant research work for this review. Moreover, the impactful studies, methodologies and preventive measures undertaken during the past five decades on the effect of heat stress on underground miners were retrospectively analysed, with a broader aim to explore the need for further research on this pertinent topic. Overall, 571 references were identified from the literature review, out of which 51 research articles addressing the sources of heat, heat stress effects on miners, heat stress indices and control measures for heat stress in underground mines were selected as primary papers for detailed review. Pre-developed fatigue is one of the prime causes of health hazard, safety and productivity loss of miners working in underground high heat stress zones. Hence, development of a better heat stress index integrating personal, environmental parameters and pre-developed fatigue (PDF) of miners is essential.

Jan 14, 2022

By C. L. Lin

The image-based On-line Particle Size Analyzer (OPSA) system has been developed at the University of Utah to measure particle size distributions under plant conditions where overlapped and segregated particles are being transported on a moving belt conveyor. Evaluation of the OPSA system at several plant sites has been completed. The results show a consistent agreement between the particle size distributions obtained from the OPSA system and those obtained from laboratory screen analysis of belt samples. These results and the stable performance of the OPSA system during the field tests suggest that continuous quality control of crushed products is possible using the OPSA system.

Jan 1, 1999

By B. M. Eiter, J. Hrica, D. R. Willmer

"Mineworkers are routinely tasked with making critically important decisions about whether or not a hazard presents an imminent danger. Researchers from the National Institute for Occupational Safety and Health (NIOSH) collected formative data to investigate mine safety professional perspectives on workplace examinations, which revealed a potential gap in how mineworkers are assessing risk. During interviews, participants indicated having processes in place for what should be done once an imminent danger situation is identified. Critically, however, they report having no systematic methodology for mineworkers to use to determine if a hazard is considered imminent danger. While this is important for all imminent danger situations (e.g., failure to lockout/tagout), it is especially important for those situations that are not immediately recognizable as imminent danger. In this paper, we identify and describe, three distinct categories of imminent danger complexity and discuss potential steps that could lead to improved identification of imminent danger situations. Finally, we identify potential practices to incorporate into risk management efforts, including feedback, communication, and specialized training to increase awareness of imminent danger situations. INTRODUCTION In recent years, the metal and nonmetal (M/NM) mining sector, as categorized by MSHA, experienced an increase in the number of fatalities occurring at mine sites. From 2013 to 2015, 69 mineworkers were fatally injured; that is twice the number of fatalities that occurred in each of the previous two years (MSHA, 2015a). As a way to address this increase, the Mine Safety and Health Administration (MSHA) issued a program policy letter (P15-IV-01) suggesting that “miners would benefit from rigorous workplace examinations conducted by experienced and trained examiners (MSHA 2015b).” The goal of workplace examinations is to find hazards in the field and mitigate them before they cause injury or death to mineworkers. While it is important to identify all hazards in the workplace, it is critically important to identify those hazards that are considered imminent danger because they require an immediate response to avoid a severe or even fatal injury."

Jan 1, 2018

By E. Hasanbas

Vibrating screens and crushers are the workhorses of material sizing. Unfortunately their natural frequency is often in the range of typical supporting structures, thereby making installations prone to vibration problems. Much of the available literature regarding the support of vibrating screens is fairly confusing and outdated. This paper presents the results of utilizing accelerometers and finite element software in the analysis and design of supports for vibrating equipment. It contains data from field studies of vibrating screen and crusher installations, design of new and repair of existing supporting structures, and the correlation between field data and finite element time history analyses. Finally, the paper summarizes a method for analyzing and designing structures subjected to vibratory loads and predicting their behavior.

Feb 23, 2014

By L. Zhou, D. Bahrami

Mine ventilation is one of the most important aspects of mining operations in underground mines. It is critical to maintain and deliver required fresh air to the active areas to reduce the risk of overexposure to hazardous contaminants or explosive atmospheres. An unexpected or unknown event such as roof collapse, unexpected mine door closure/opening, a fire/explosion, or fan malfunction could adversely alter the airflow distribution within the mine ventilation network that could lead to a hazardous underground environment. Knowing the occurrence and location of such an incident is of critical importance. In this study, the authors developed a novel methodology to assist mine operators in quickly identifying the location of any abnormal airflow change within the network using the airflow changes at monitored airways. The concept is based on a direct derivative method developed by the authors. This paper provides the details of the developed method as well as numerical verification examples. The application of this method can benefit mine operators and safety personnel in making better decisions during a mine emergency response operation to mitigate hazardous conditions arising from an unexpected airflow disturbance

Mar 2, 2022

By P. Rusin

Toxic substances in On solutions can retard biological leaching of copper sulfide dump ores. On solutions were analyzed for metals, organics, and chloride, and showed inhibitory concentrations of aluminum, manganese, and chloride. Inhibition of bacterial activity by the solid fraction of On solution, with and without the organic constituents, was evaluated. Toxicity to bacterial species was evaluated by monitoring bacterial numbers, pH, Eh, and rates of iron oxidation. The On solution solids were toxic at 50 -60% of their field concentration. Most of the toxicity of the On solution was due to the organic fraction. Different SX reagents show varying degrees of inhibition of T. ferrooxidans. Bacterial inhibitory effects of carriers and lixiviants used in the SX plant should be determined so that entrained SX reagents do not retard biological dump leach systems. The reagents used should be the most cost effective and the least toxic.

Jan 1, 1994

By A. K. Stagg

Toxic substances in On solutions can retard biological leaching of copper sulfide dump ores. On solutions were analyzed for metals, organics, and chloride, and showed inhibitory concentrations of aluminum, manganese, and chloride. Inhibition of bacterial activity by the solid fraction of On solution, with and without the organic constituents, was evaluated. Toxicity to bacterial species was evaluated by monitoring bacterial numbers, pH, Eh, and rates of iron oxidation. The On solution solids were toxic at 50 -60% of their field concentration. Most of the toxicity of the On solution was due to the organic fraction. Different SX reagents show varying degrees of inhibition of T. ferrooxidans. Bacterial inhibitory effects of carriers and lixiviants used in the SX plant should be determined so that entrained SX reagents do not retard biological dump leach systems. The reagents used should be the most cost effective and the least toxic.

Jan 1, 1994

By C. Sunderman, G. Feagan, C. Stazick

Galvanic corrosion between dissimilar materials, such as steel and graphite, leads to safety concerns for many industries, including mining. In this study, researchers from the National Institute for Occupational Safety and Health (NIOSH) analyzed rock samples from two mines in the United States that exhibit electrochemical properties similar to graphite through laboratory measurements to investigate their observed in-situ influence on underground metal support. Uniform corrosion rates of mild steel coupons, inflatable bolt coupons, and friction bolt coupons galvanically coupled to rock samples were obtained using both potentiodynamic polarization and zero resistance ammetry. Increased uniform corrosion rates were witnessed between the coupled rock and steel system, over those of just the steel alone. Surface analysis of the metal samples showed the presence of pitting corrosion, reflective of bolt samples removed from partner mines. Corrosion pitting of ground support structures in contact with graphitic rock in underground mines poses safety concerns for mine workers by increasing the rate of corrosion and decreasing bolt strength over time and will be further investigated for intervention strategies.

Feb 1, 2023

By S. Pastor, S. Hahn

"As the concept of autonomous haulage systems (AHS) moves from proto-types to production-ready applications, the operating performance of the haul road will become ‘mission critical’ to the overall success of autonomy in mining. Deterioration in road performance will require remediation, human intervention and significant, albeit temporary, changes to operating procedures, to accommodate road maintenance. With autonomous trucks comes the opportunity to reduce road formation and operating width, and therefore generating potentially significantly reductions in stripping ratios and improvements to mine economics, but only if the design of the road, and it’s associated deterioration rate, is predictable and manageable, based both on the materials used to construct the road and the maintenance interventions to be carried out on the road. This paper presents the assessment of a digital photogrammetric approach to the characterization of a mine haul road surfacing, or wearing course material. Design and maintenance parameters for these roads are currently determined from physical particle size distribution (PSD) assessments of ‘in-road’ material. However, this approach does not accommodate the need, nor leverage the benefits from, AHS. The digital imaging approach is assessed in this paper, using two standard digital analysis software tools, together with in-service mine haul road wearing course samples and images which are assessed to determine the applicability and reliability of the approach to deliver a real-time assessment of haul road surfacing conditions and thus to identify the road maintenance interventions required to address deterioration. INTRODUCTION Enhancements in mine road design, construction and management for the past 20 or more years has largely been focused on short-term tactical needs. These improvements have not been matched by advances in the fundamental technologies that underpin mine road design and management, and although the quality of mine roads have probably increased, many of fundamental and longer-term issues have yet to be addressed. With AHS’s evolving from prototype to production applications, any decision to implement these systems in a mine requires a thorough evaluation of impacts, not only operational improvements, but the inter-connectivity of this autonomy technology to other organizational processes. In developing an understanding, the full interactions that may affect autonomous truck behaviour due to changes in various sub-systems or external environments, haul road conditions and operating performance is a key consideration. This is as true in autonomous as well as in conventional mine truck-based hauling systems where the mine haul road network is a critical and vital component of the production process."

Jan 1, 2015

By Magnus Ericsson

The unexpectedly quick recovery in world crude steel production in the second half of 2009 was due almost entirely to increased production in China that began in late 2008. Previous peaks in monthly production in China were matched by April 2009. The rest of the world had still not reached pre-crisis production rates by May 2010. Chinese production drives growth, but there has been some growth in most other larger crude steel producing countries as well, compared to production in 2009. If the production rate of the first four months of 2010 continues, the total output of crude steel in 2010 will be somewhere around 1,410 Mt (1.5 billion st), the same as in the record year of 2007.

Jan 1, 2010

By X. Zhu, L. Chen, R. Guru, M. Peiravi, M. Mohanty, L. Ackah, B. Xu

"The overall goal of this study was to develop a suitable flowsheet to extract rare earth elements (REEs) from coal ash. Only the findings from the first part of this study is being reported at this time. A total of fourteen coal samples of different ranks were examined for REEs concentration. An anthracite coal sample, originating from Pennsylvania having more than 700 ppm (in the coal ash) was selected for the REE extraction tests. The experimental program completed so far included high temperature leaching using nitric acid, followed by the solvent extraction tests. A 4x2x2 experimental design was used to conduct a total of thirty two high temperature leaching tests by varying acid molarity (at 4 levels), solid content (at 2 level) and leaching time (at 2 level). The highest LREE (light REE) recovery of 90% and HREE (heavy REE) recovery of 94% were obtained from the most optimum leaching test condition while maintaining the impurity recovery to the leachate at less than 40%. Solvent extraction experiments were conducted to recover the REE’s from the above leachate solution using a variety of organic extractants including, TBP, Cyanex, D2EHPA and their combinations. D2EHPA was found to be the best extractant during this SX text series providing nearly 99% recovery of REEs. INTRODUCTION The demand for rare earth element and other strategic metals (REM) in the world is rapidly increasing due to their use in a variety of high technology applications. More than 100,000 tons of rare earth oxides (REO) are being used worldwide on an annual basis. However, we have less than 10% of the world reserve of rare earth element (REE) mineral deposits in the US. More than 60% of rare earth oxide (REO) was imported to the US from outside (mostly from China) in the year of 2013. However, China’s institution of export quota has significantly reduced the supply of REMs to the U.S. Hence, new ways of producing REM and/or finding substitutes for those metals for the high-tech applications need to be invented/discovered in a timely manner. Coal Combustion Byproducts (CCBs), which are discarded as waste materials in most cases, are known to contain REEs (in low concentration) that could be extracted using a suitable process flowsheet. This may be a worthwhile route to pursue considering the short supply of REMs and the abundance of coal ash in thousands of ash ponds in the US. On an annual basis, more than 110 million tons of Coal Combustion Byproducts (CCBs) are being produced while satisfying our nation’s need for electricity (ACAA, 2014). However, less than 50% of these CCBs are being successfully used in various applications and the remainder is being dumped as waste materials in the landfills and ash ponds."

Jan 1, 2017

By J. C. Stankus

Many coal seams are associated with soft floor strata and during mine development if coal pillars are not properly designed, floor heave occurs and causes interruption of coal production. In the severe cases, the section or mine is abandoned. One of the methods for controlling floor heave is floor bolting. This paper describes the demonstration of floor bolting methods in a West Virginia coal mine. Three methods were used: (1) vertical full resin bolting, (2) floor truss bolting, and (3) floor truss bolting plus a floor cut at the center of the entry. The design of each method and the experimental results are discussed in detail.

Jan 1, 1993

By Shaoyang Yan, Xinming Chen, Huazhe Jiao, Huaibao Chu, Chang Wang

In terms of the technical problems of rib spalling in large mining height coal face, a long-distance advanced pre-grouting layer flexible reinforcement technology is proposed in this paper. Based on the mechanism and failure mode of rib spalling in the coal face, the mechanical properties of the aluminum plastic composite pipe were analyzed by using the tensile and compression experiment. The deformation and strength characteristics of “flexible pipe + grouting” specimens were studied by uniaxial compression test, splitting test, and shear test. The UDEC numerical simulation software was used to simulate the reinforcement effect of “flexible pipe + grouting” at different positions. Combined with the field application, the feasibility of long-distance advanced pre-grouting layer flexible reinforcement technology was verified. The test results show the following: The coal face has the characteristics of brittle and large deformation. The aluminum plastic composite pipe has the characteristics of good elongation and tensile strength, which can endure the large deformation of the coal face. The “flexible pipe + grouting” can improve the tensile and shear strength of coal. The UDEC numerical simulation analysis indicated that the grouting hole layout of “flexible pipe + grouting” has a significant difference in the reinforcement effect of the coal face. Compared with single row grouting reinforcement, the reinforcement effect of double row grouting holes 1.5 m and 3.0 m away from the roof is better. According to the field application, it is feasible to use aluminum plastic composite pipe as a flexible grouting pipe to reinforce coal seam with 80–100 m long-distance pre-grouting. Long-distance advanced pre-grouting layer flexible reinforcement technology can improve the daily production of coal and reduce the support cost of the coal face. As a new method of reinforcement, long-distance layered flexible reinforcement has a significant effect on the prevention and treatment of rib spalling in large mining height coal face.

Sep 27, 2022

By Sumit Kumar Hota, Asadi Srinivasa Reddy, Ashok Kumar, Ashish Agrawal, Surajit Sinha, Chandra Sekhar, Tanay Ray

In the current operational facility, due to the absence of pellet pot facility, a novel technique is developed wherein the pellets with different chemistries prepared in the laboratory are fired in an induration machine by placing them inside the Inconel baskets. In the present work, an attempt is made to optimize the pellet chemistry by developing 2 different flux pellets, viz., low basicity (B2: CaO/ SiO2 = 0.3) pellets and high basicity (B2 = 0.9) pellets, and further the effects of basicity on pellet properties, viz., cold compressive strength, porosity, swelling index, reducibility index, and softening and melting temperature, are studied. It has been found through the multiple operational trials that increasing the basicity of pellets from 0.3 to 0.9 results into improving the pellet strength, reducibility and softening and melting characteristics. Moreover, it is observed that the swelling index of pellets is reduced by adding 2% MgO to both low and high basicity pellets that could be attributed to the formation of high melting point slag in pellets. The operational trial has resulted into producing pellets that exhibit a combination of desired mechanical strength, improved swelling, and reducibility index and possess better softening–melting behavior among all the chemistries studied.

May 24, 2022

By Y. H. Zhan

A new P(MAAA) latex was developed and used in separation of ultrafine apatite from calcite and silica by means of selective flocculation. The latex was found to flocculate selectively apatite from apatite/calcite and apatite/silica mixtures in the presence of sodium tripolyphosphate and sodium silicate over a pH range from 9.1 to 9.4. The separation of apatite from calcite was more selective with sodium tripolyphosphate, while the results of the separation of apatite from silica were better when sodium silicate was used. In the apatite/calcite system, 90% apatite recoveries into a concentrate containing 34% P2O5 were possible in the presence of 4 mg/l of sodium tripolyphosphate at a latex dosage of 2.2 kg/t. In the apatite/silica system, 80% of apatite could be recovered into a concentrate containing 33% P2O5 in the presence of 20 mg/l of sodium silicate at a latex dosage of 1.1 kg/t. Deposition tests were used to study the interaction between the latex and the mineral surfaces. The results revealed that deposition density of the latex on apatite was higher than on calcite; the differences between the deposition onto these two minerals were higher at pH 9.2 than at 7.2. The results point to the stronger interaction between the latex and apatite surface when compared with the latex-calcite interactions.

Jan 1, 1998