Search Documents

By D. Kimball, P. Chambers

"BACKGROUND In the event of an explosion or fire in an underground mine, workers can be exposed to a deficiency of oxygen, an excess of carbon monoxide, or both. These threats can occur as separate conditions or simultaneously. A lack of oxygen in the breathing air can only be addressed via the use of a self-contained breathing apparatus (SCBA) acting as a source of oxygen. An excess of carbon monoxide can also be addressed via the use of an SCBA, but if the threat occurs in isolation (that is, the atmosphere still contains sufficient oxygen to support life) and the concentration of the threat gas is not extreme (< 2%) then the carbon monoxide threat can also be addressed by the use of a filter self-rescuer (FSR). Used together, the SCBA and FSR offer a far more efficient and universally capable life support system than when used in isolation. However, the SCBA does not take advantage of the fact that the surrounding atmosphere likely contains some level of useable oxygen; i.e., the SCBA always supplies the total required oxygen from its limited supply, resulting in a ceiling on its useful life regardless of the level of oxygen in the surrounding air. To address this technology gap, what is needed is a ""smart"" SCBA that provides filtration and catalytic protection against threat gasses and has an extended duration life-sustaining oxygen inhale stream independent of the threat content and oxygen deficiency of the surrounding atmosphere. DEVELOPMENT Developed under contract with NIOSH the Smart Escape SCBA is comprised of three major components including; 1) oxygen supply, 2) oxygen sensing & dosing electronics and, 3) a CO catalyst and carbon bed broad spectrum FSR. The SCBA is designed as a hybrid system that provides non-toxic breathing air by using an approved Chemical, Biological, Radiological and Nuclear filter self-rescuer and a catalyst to convert high levels of carbon monoxide to harmless carbon dioxide (CBRN FSR/CO). In addition, the Oxygen Sensing & Dosing Electronics (OSDE) package adds sufficient oxygen to make up for deficiencies detected in the ambient air (Figure 1). By making use of the ambient oxygen, less oxygen is required for a one-hour unit life. This means that the Smart Escape SCBA fits in a smaller and lighter package than a similar-duration conventional Self-Contained Self-Rescuers (SCSR). Alternatively, taking advantage of available ambient oxygen could offer a significant increase in working duration in a unit with the same size as current SCSRs. The research performed under this NIOSH contract involved numerous tasks including: (1) definition of performance and system requirements for the Smart Escape SCBA, including keeping environmental stressors within acceptable ranges, providing at least one hour of breathable oxygen supply, and using a mask or hood that allows high-quality voice communication; (2) designing, building, and evaluating prototype units to support extensive bench top testing at Avon Protection and third party labs to demonstrate the device’s capabilities; (3) building sufficient quantity of Smart Escape SCBAs designed to be intrinsically safe (per MSHA criteria); (4) testing and evaluation by the National Personal Protective Technology Laboratory (NPPTL)."

Jan 1, 2015

By Jon Y. Kaneshiro, Eric Dawson, Pooyan Asadollahi, Steven Hunt

This paper provides updates to the paper published by the lead author at RETC 2011 with a summary of developments in technologies, products, and approaches to corrosion analyses of gravity sewer tunnels and microtunnels. This paper presents approaches in evaluating degradation of reinforced concrete liners. Also, the carbon footprint of conventional concrete liners and alternative “green” liners are compared and their life cycle costs are considered. A few case histories from the past decade are provided indicating the latest and emerging trends in liner protection.

Jun 13, 2023

By Donald W. Gentry

This section deals with one of the most fascinating aspects of mining the evaluation of mine investment opportunities. Be-fore proceeding further, it is important to clarify the meaning of some fundamental terms used frequently in the text. 6.0.1.1 Mine Valuation vs. Evaluation The words "valuation" and "evaluation" in a mining context are often used interchangeably. However, for the purposes of this section, a distinction is made between the two terms in accordance with commonly accepted practice. The word valuation in a mining project context has the rather narrow meaning of placing a dollar or other currency value on the worth of the project as a whole. In other words, the value of a mining project refers to a measure of the desirability of ownership of that property. As such, the major item of interest is, "what is the mine worth?," or `what is the value of the mine?" The value of a mining project may actually be determined in the marketplace at any specific point in time, or it may be estimated by one of several methods. The topic of mine valuation is discussed in more detail in Chapter 6.1. The word evaluation in a mining project context connotes the broader meaning of determining the numerical values of all

Jan 1, 2008

By Donald L. Freed

Design, development, factory test, and in-mine evaluation plans are presented for an Automated Extraction System (AES) that has been designed to fill needs which are present in the Mining Industry. The philosophy of design and proposed operation of the machine, as well as the relationships between these factors, and final machine configuration are reviewed. The AES is designed to overcome production problems resulting from the regulation of roof control, clean-up, ventilation, dust suppression, and operator protection required by the Federal Coal Mine Health and Safety Act of 1969. The design permits more continuous operation and greatly improves operator safety. The machine is a full-face drum-type continuous miner which includes self-advancing, continuous temporary roof support. Onboard self-advancing face ventilation, dust suppression, and air scrubbing equipment are also included in the design. A further improvement over existing equipment is the incorporation of an automatic programmed cutting cycle control system. All mining functions including movements of the roof support system are handled by this automatic system.

Jan 1, 1977

By R. E. Anderson

Canada encompasses an area of approximately 9,976,000 kilometres. It is comparable in size to the United States, but because of climatic conditions and limited transportation facilities, much of the area is unsuitable for agricultural or industrial development. We have a population of 22,000,000 - most of whom reside within a hundred mile belt paralleling the Canadian-U.S. border. Our principal cities in order of size are Montreal, Toronto, Vancouver, and Winnipeg. We have a total of 10 provinces, each of which elects its own - government. The Yukon Territory and Northwest Territories covering the northern half of the country, are administered by federal government agencies. The mining industry employs approximately 9% of the labour force and accounts for more than 40% of all tonnage shipped on Canadian railroads and inland waterways. In 1974 it produced $4,800 million in mineral wealth. Canada ranks first in world production of asbestos, nickel, zinc, and silver and has significant production of copper, iron, molybdenum, lead and other mineral commodities. During the past decade Canada, like many other western countries, has undergone dramatic economic and social change. This trend is continuing, and its effect on the Canadian mining industry has produced conflicting results. From the industry&apos;s point of view, some of the more negative aspects include a steadily increasing involvement by government at municipal, provincial and federal levels through the imposition of Stricter controls, regulations and taxation policies, a rising tide of nationalism, which advocates public ownership of all natural resources, the spectre of inflation (currently increasing at the rate of 8% per year) and unsettled labour conditions.

Jan 1, 1976

By D. E. Ranta

Orebodies with intricate three-dimensional shapes (such as porphyry molybdenum deposits) are difficult to model using geostatistics or other computer-assisted methods. The strong trends in their spatial grade distributions occur as mathematically complex shapes and prevent the customary assumption of local stationarity that is required for accurate ore reserve estimation. "Zoned Kriging", a new method developed by AMAX, solves this problem directly by using the geologist&apos;s interpretation of the ore zones as a parameter in the kriging equations. The geological basis and methods used in the Climax ore zoning technique are reviewed and discussed relative to their application in zoned geostatistical modeling. The Zoned Kriging technique is described and demonstrated using data typical of mineral deposits.

Jan 1, 1984

The evaluation of Abandoned Mined Lands can involve the investigation of very large areas of land. Often, the locations of critical areas or impending problems are unknown, and are not easily identified from the surface. Microseismic monitoring has been demonstrated to be effective in identifying potential instabilities and active movement in mines from distances of several kilometers. By placing sensors in proximity to, or in contact with, a high acoustic conductance layer close to the mined zone, large areas can be monitored for potential problems with a minimum of sensors and drillholes. As part of a U.S. Bureau of Mines contract, a prototype system was developed to identify and locate potential instability problems over wide areas of land. Once a problem area has been located, the system can be used to analyze the type of the problem, its size, relative degree of instability, and potential for damage. Continued monitoring after application of remedial measures can effectively determine the efficacy of those measures.

Jan 1, 1993

By g. Caproni

The main constituent of the feed to the "Sulphide Section" (31 t/h), in the F. Sartori Plant (6000 tid) of the Miniere di Mon)eponi(Sardinia), is the ore of the Campo Pisano -Funtanaperda Mine (1 ? Difficulties have always been experienced in the treatment of this ore, owing to the extramely fine Pyrite-Sphalerite intergrowth and to the high Pyrite and soluble salts contents. The first mentioned difficulty was overcome with a rather complex flowsheet (see fig.1A and lB)(2); the others with a reagent combination that required a pH of 11 in a pulp loaded with soluble salts. This meant high consumption of alkalizer, and also of the other reagents; furthermore the alkalizer had to be mainly NaOH with only minor amounts of lime, because the latter tended to depress not only the pyrite but also the middlings, which were supposed to float. With dialchylditiophosphate alone as a collector, a lower pH could have been used, but a certain amount of amylxanthate was indispensable to promote flotation of the middlings. On the other hand, a bulk-flotation of sphalerite and pyrite at low pH could not be very advantageous on account of the high pyrite content in the feed(3).

Jan 1, 1971

By T. Cienski

The paper presents and discusses the results of a detailed study conducted on the subject of energy consumption in the comminution of industrial minerals. The study was based on pilot circuit testing, plant operating data collection, detailed equipment data and literature research. The areas covered by investigations include: high efficiency classification; air classifiers for cement grinding circuits; grinding aids in dry grinding: dry grinding circuit, control based on particle size measurement. Results obtained indicate a large potential for the reduction of energy consumption, in particular in the traditionally high cement clinker grinding circuits. Better classification techniques and correct application of grinding additives can significantly reduce power used per ton of product and also substantially increase grinding circuit output.

Jan 1, 1990

By Osamu Nishikokura, Jumpei Yamashita, Darrell Liebno, Malcolm Sheehan

"The Eglinton-Scarborough Crosstown Project builds a 19km LRT corridor that includes a 10km underground portion, between Keele Street and Laird Drive. The West Tunnel Contract (ECLC1-15) includes 6.5km of twin EPB TBM bored tunnels with a 5.75m internal diameter precast concrete segment lining (PCTL), between Keele Street and Yonge Street. This paper summarizes the overall scope of work, the technical challenges faced and innovative solutions developed by the contractor during the TBM move across an existing subway tunnel using state of the art high capacity strandjack gantry crane.1. PROJECT OVERVIEW The Greater Toronto and Hamilton Area (GTHA) is Canada’s largest urban region, populated with over 6 million people, and is one of the most rapidly growing regions in North America. One forecast estimates that the population of this region will increase to 8.6 million by the year 2031. In September 2008, Metrolinx, an agency of the Government of Ontario, launched a 25-year regional transportation plan named “The Big Move” to cope with the expected increase in transportation demand. The Eglinton-Scarborough Crosstown, one of the projects included in “The Big Move”, is a light rail transit (LRT) that will run across Toronto in an east-west direction between Mount Dennis and Kennedy along Eglinton Avenue. In October 2012, the West Tunnel Contract of the Crosstown LRT (ECLC1-15) was awarded to Crosstown Transit Constructors (CTC), a joint venture between Obayashi Canada Ltd., Kenny Construction Company, Kenaidan Contracting Ltd. and Technicore Underground Inc. The project includes approximately 6.2 km long twin bored tunnels, 9 cross passages, 1 emergency exit building, 7 sets of station headwalls, and an intermediate pair of extraction and launch shafts. Each of 6.5 km long twin tunnels are divided by the existing subway station into two drives: the first half from the launch shaft LS-1 (west of Keele Station) to the extraction shaft ES-1 (west of Eglinton West Station), and the second half from the launch shaft LS-2 (east of Eglinton West Station) to Yonge Station, as shown in Figure-1. The TBMs are extracted at ES-1 and moved to LS-2 over the existing Yonge-University Subway Line at Eglinton West Station before resumption of tunneling at LS-2."

Jan 1, 2016

By Hingant Pierre

The Hurtières Tunnel was built in 1995 with drill and blast method, in metamorphic schist. It is located between Lyon and Torino on the A 43 motorway in the French Alps. During the construction, a geological hazard was encountered, which caused a massive ground collapse. The tunnel was filled up with 3,000 m3of glacial materials. Geological investigations realized after the accident showed that a narrow glacial valley was present at this location the water table was 40 m above the tunnel level. The paper will describe the collapse and the remedial methods which were implemented to proceed through the failure area. These included drainage works,2,000 m3 grouting and 6,200 ml jet grouting columns.

Jan 1, 1999

By W. J. Douglas

The mine manager in today&apos;s environment is faced with a wide variety of problems and challenges which must be addressed if efficient and profitable operations are to be achieved. Expansion of operations has, in many instances, resulted in inexperienced work crews, face supervisors, and superintendents. The complexities of a mining system preclude rapid movement through the learning curve for moat personnel. The management of production suffers both from this inexperience and the lack of standard procedures and methods for planning, schedul ing and analyzing production systems. The lack of visibility of information, as well as of the operations themselves, due to their remoteness, adds to the problem of production management.

Jan 1, 1980

By Charles A. Beasley

Coal conversion to electricity or to substitute natural gas requires a significant quantity of natural and human resources including, in addition to the coal resource base, land, water and the construction and operating labor force. Each method of coal conversion has its advantages and disadvantages relative to conversion efficiency, preferred method of resultant energy transportation, resources consumed, and impact on the environment. Regulations which have been passed in recent years to maintain or restore the pre-project environment can add significantly to the capital and operating costs of both a conversion facility and its associated mine.

Jan 1, 1983

By M. R. Hieb, J. R. Britt, S. P. Harteis, M. J. Sapko, E. S. Weiss, R. K. Zipf

The design requirements for mine ventilation seals have undergone a radical transformation in recent years, and these revisions have greatly increased the cost of the seal designs and their construction. For example, in the past two years, new federal regulations have increased the minimum design requirement to withstand explosion pressures from 138 kPa (20 psig) to 345 kPa (50 psig) or 827 kPa (120 psig), depending on whether the sealed mine volume is monitored continuously or not. Moreover, there is still a possibility that under certain conditions (such as detonations), even higher pressure requirements may be necessary. The ability of a monolithic, stand-alone mine seal to reliably withstand the full range of possible explosion pressures is becoming increasingly difficult and expensive. In an effort to develop a practical alternative, the West Virginia Office of Miners’ Health Safety and Training (WVOMHST) and the National Institute for Occupational Safety and Health (NIOSH) have collaborated in a research effort to develop a practical, economic and safe mine sealing technique that can enable mine seals to meet the full range of new explosion pressure design requirements. The basic idea is to use a barrier of common mine gob and rubble, in combination with a conventional mine seal, so that the pressure resulting from a gas explosion is reflected, absorbed and attenuated, and the pressure on the ventilation seal is reduced. This paper discusses some concepts and preliminary test results for a “passive mine blast attenuator” (PMBA) that can provide a useful alternative to increasingly larger and stronger stand-alone mine seals. Numerical models and full-scale experiments conducted at the NIOSH Lake Lynn Laboratory Experimental Mine (LLEM) show that the use of a PMBA can signficantly reduce the blast pressure and impulse on conventional ventilation seals.

Jan 1, 2009

By Ava Segal, Doga Cagdas Demirkan, Abhidipta Mallik, Sebnem Duzgun, Andrew J. Petruska

Search and rescue operations in mining heavily rely on humans. In the context of emergency situations within underground tunnels, the potential to utilize sensory technology for navigation assistance holds the promise of saving human lives. Our research introduces a device configuration designed to enhance the performance of search and rescue teams. This setup integrates LIDAR and thermal cameras with the Microsoft Hololens, facilitated by the NUC computer and ROS Bridge. Performance assessment involves quantifying the extent to which a user is willing to venture into a light-deprived section of the mine prior to necessitating supplementary illumination. The preliminary outcomes highlight the significant potential of augmented reality assistance in offering indispensable aid to first responders, thereby greatly augmenting the efficiency of search and rescue missions conducted during critical circumstances.

Feb 1, 2024

By Robert W. Row

The run-of-mine coals in the U.S. being fed to coal cleaning plants have become increasingly finer due to the adoption of modern, mechanized mining methods, and economics are dictating that finer fractions, as well as the coarser fractions, be cleaned. Traditional dewatering methods (vacuum disc filters and centrifuges) are proving inadequate for preparing fine refuse for disposal or fine coal product for downstream handling. The Electric Power Research Institute has been supporting research into the nature and limitations of mechanical dewatering, and novel ways of improving it. The efficiency of various silicone-based chemicals at aiding dewatering was investigated, and it was shown that the final moisture content of hydrophilic coals after vacuum Filtration could be reduced by 1 to 5% with up to 40% increase in filtration rate by addition of one of several of these silicones. EPRI also has an on-going program at its Coal Cleaning Test Facility to investigate the performance of the Larox pressure filter in comparison with that of the disc filter and solid bowl centrifuge. While improvements to the dewatering performance currently being obtained in existing operating plants by such means are achieveable, a fundamental study has shown that, regardless of changes in operating conditions, there may be a limit to the lowest cake moisture content attainable by mechanical dewatering of a given sample of coal fines. Determination of this limit for a specific coal would be useful in designing facilities to dry and handle it.

Jan 1, 1984

By C. E. Jordan

The fundamental properties of the Bureau of Mines patented dielectric separator were studied to provide insight regarding its design and operating characteristics. Force equations for mineral particles were derived and evaluated experimentally. High dielectric mineral recovery was proportional to the calculated effective dielectric force volume that surrounded each drum electrode wire. Electrode spacing was the most sensitive design parameter, requiring less than 0.4-cm electrode spacing for a good separation. Operating characteristics and ore characteristics were investigated. With a dielectric constant difference as small as 2, good separations were made on a laboratory scale at energy consumption below 12 kw?h/mt.

Jan 1, 1985

By Stephen A. Orr

Underground mining is a dynamic art and science with a diverse set of design, production, and economic criteria that must be considered before selecting an optimal method to extract the ore. While all methods can be technically classified as either self-supported, supported, or caving, the multitude of subsystems and existing variations bear witness to the fact that each orebody is unique and, as such, justifies an individual approach to optimize mineral extraction. In this sense, underground mining is an art. The ability to evaluate the unique characteristics of each ore body and utilize sound engineering principles to design the optimal system constitutes effective method selection. The task by no means ends at this juncture, however. Subsequent implementation requires an ability for modification. Very rarely are all the facts available to make a concrete decision prior to development of the resource. As a result, the risk of a wrong decision can never be eliminated. This requires a significant degree of flexibility with each method. Each unit of exploration, development, or exploitation work contributed to a deposit enhances knowledge of the ore body. The best mining methods are those that correctly account for the known parameters but provide an allowance for change at minimal cost and adapt to unanticipated conditions.

Jan 1, 2008

By Paul Piercy

Bougainville Copper Limited operates a porphyry copper mine in Papua New Guinea. The waste dumps will contain 400 to 500 million tomes of rock at the end of nine life. The paper describes investigations carried out over a period of en years and highlights the problems associated with waste lump leaching in a tropical and seismic active region. Aspects discussed include mineralogy, chemical reaction, leaching rates, microbiological activity, dump stability, dump structures, effects of tropical conditions, seismic activity and topography.

Jan 1, 1981

By T. F. Tomb

Although the number of operating longwalls (approximately 100) has remained relatively constant over the last five years, longwall production levels have significantly increased and have in some cases more than doubled. As a result of the increase in production, control of respirable dust continues to be a problem. Therefore, the Mine Safety and Health Administration (MSHA), Pittsburgh Health Technology Center, Dust Division, initiated a study to investigate the availability and adequacy of technology for controlling dust on longwall mining operations. The study involved 23 longwall mining operations in three different Coal Mine Safety and Health Districts. Each operation was visited for a full shift. Respirable dust samples were collected on face personnel and at fixed locations along the face. Parameters in place to control dust were noted with special emphasis being placed on obtaining quantitative data relative to ventilation, headgate dust controls, cutting drum sprays, external machine sprays and cutting sequence. Attempts were made to correlate dust control parameters in place at the time of the visit to dust concentrations measured at the tail, on the tail shearer operator and to the average concentration of dust determined from averaging all the measurements from the occupations sampled. The parameters in place to control dust were also compared to the gamut of technology known to be available to control dust. This paper presents a discussion on the effectiveness of the parameters in place to control dust and on the availability of technology for the control of dust on longwall mining operations.

Jan 1, 1990