Search Documents

By M. Le Roux

Fine coal (-500 µm) is notoriously difficult to dewater. It is not uncommon for a dewatered product to have a moisture content as high as 30 per cent after vacuum filtration. This poses several handling and financial problems to such an extent that a lot of fine coal is discarded onto slurry waste ponds. A novel way of dewatering fine coal was developed at North-West University. It entails deliberately damaging the filter cake during dewatering to allow for an increased flow of air through the cake at the expense of the applied pressure differential. This method resulted in an average improvement in final cake moisture of between 3 per cent and 5 percent when executed in the laboratory under controlled conditions. A device was designed that could be fitted onto existing belt filters that would damage the filter cake as it passes by. This device was tested on a vacuum belt filter installation at a coal beneficiation operation in the Waterberg coal field in South Africa. The results showed a 3 per cent reduction in final moisture of the cake, proving the validity of the method at full industrial scale.

Jan 1, 2012

By T. Phiri, Antoine Floribert Mulaba-Bafubiandi

Microwave energy has been recently used in minerals processing to speed up the leaching process or to improve the liberation of targeted minerals (Al-Harahshed and Kingman, (2003); Bradshaw et al., (2001)). Applied to the roasting of sulphide minerals, microwaves allow the ?tunning? of calcine types and products quality in addition to the energy savings as opposed to the conventional roasting (Mulaba, 2006). As more than 85% of world zinc is produced through the ?roast-leach-electrowin? route, an attempt was made to optimize cost, energy and product quality for metal extraction process route. The use of microwaves was the alternative process route selected for the optimisation. Pyrite concentrate (0.17% Zn, 0.09% Cu, 35.71% Fe, 43.76% S) and sphalerite concentrate containing 43.81% Zn, 0.37% Cu, 3.86% Fe and 44.39% S were microwave roasted in a multimode cavity of 2.45 GHz with varying power levels and for different durations. The produced calcines were characterized using AAS, XRF, XRD and Mossbauer spectroscopy while the determination of residual Sulphur was used as products quality control tool to ascertain the degree of roasting achieved on the feed. The leachability of the produced calcines in HCl, HNO3, H2SO4 and HNO3 + HCl has been studied in terms of the best leaching yield, process kinetics economics and environmental aspect. With 800 W power for 30 minutes, ZnO and Fe2O3 were formed corresponding to a 70% sulfur removed from sphalerite and 80% from pyrite concentrates respectively. While the roasting of the above concentrates appeared to be a first degree processes, it was noticed that the microwave assisted roasting of sphalerite and pyrite concentrates yielded lower sample surface temperature for a shorter time (i.e.less than 30 minutes) microwave exposition. Longer time (more than 30 minutes) microwave exposure showed a linear increase in temperature in function of power level used. While optimum roasting conditions were found at 800W, 30 minutes, a 10% increase of sulfur removal was noticed while pyrite concentrate was microwave roasted. Sulfuric acid was seen to give higher leaching yield than nitric acid. Zinc dissolution was hindered by the presence of franklinite.

Jan 1, 2007

By M. Le Roux

Fine coal (-500 µm) is notoriously difficult to dewater. It is not uncommon for a dewatered product to have a moisture content as high as 30 per cent after vacuum filtration. This poses several handling and financial problems to such an extent that a lot of fine coal is discarded onto slurry waste ponds. A novel way of dewatering fine coal was developed at North-West University. It entails deliberately damaging the filter cake during dewatering to allow for an increased flow of air through the cake at the expense of the applied pressure differential. This method resulted in an average improvement in final cake moisture of between 3 per cent and 5 percent when executed in the laboratory under controlled conditions. A device was designed that could be fitted onto existing belt filters that would damage the filter cake as it passes by. This device was tested on a vacuum belt filter installation at a coal beneficiation operation in the Waterberg coal field in South Africa. The results showed a 3 per cent reduction in final moisture of the cake, proving the validity of the method at full industrial scale.

Jan 1, 2012

By W. E. Lee

Penetration and dissolution mechanisms are reviewed for predominantly single-phase oxide, two phase oxide and oxide-carbon composite refractories by liquid silicate slags. Theoretical models of these processes, as well as static (sessile drop, dipping and crucible) and dynamic (rotating finger and rotary slag) experimental tests, along with their practical limitations are considered. Direct (congruent or homogeneous) attack is controlled by the reaction rate at the slag-refractory interface or the rate of diffusive transport of species to it through the slag leading to active corrosion. Indirect (incongruent or heterogeneous) attack is controlled by diffusive transport through the slag or through a new solid phase, which forms at the original slag-refractory interface. This may lead to passive corrosion. Examples of direct and indirect attack in a range of refractory/slag systems are described highlighting the critical influence of the composition and hence viscosity of the local liquid slag adjacent the solid refractory. Penetration and corrosion can be controlled either through the local slag composition via the refractory or the bulk slag or by microstructural control of the refractory by e.g. internal generation of dense layers or external deposition/generation of passive coatings, so-called in situ refractories.

Jan 1, 2004

By M. K. Elmouttie, G. V. Poropat

The analysis of structure using joint set statistics is well known. Other data such as the position of discontinuities and the contacts between rock mass units cannot be easily incorporated in simple statistical analysis based on orientation alone. Algorithms to model the structure of rock slopes using measurements of the orientation and position of discontinuities are being developed by CSIRO Exploration and Mining. These algorithms provide a capability to model the structure of a rock slope and estimate the likelihood of the formation of hazardous blocks in existing or proposed rock slopes and identification of the location and size of these blocks. The algorithms provide the basis of structural modelling to identify potential failure mechanisms in rock slopes.

Jan 1, 2006

By I. Gil, J. -C. Roegiers

Abstract Hydraulic fracturing is a technology that has been utilized for more than 50 years in the oil industry. It was originally used for stimulating hard, brittle formations which typically exhibit low permeabilities and roughly linear elastic behavior. Nonetheless, an increasingly important segment of the industry is currently stimulating very soft and poorly consolidated formations; where the assumptions of ideal elasticity and relatively small fluid leakoff fail to hold (e.g. Gulf of Mexico, West Africa, Alaska, East China). In these rocks, hydraulic fracturing stimulation has been used for several years to control and solve critical production problems such as sanding and formation damage (caused during completion and drilling operations). Although successful1, the application of this method has not been accompanied by robust fracturing modeling techniques. In addition, long term production increases were often not materialized. In other words, engineers have been able, via trial-and-error, to avoid major ‘operational’ problems but with no optimization of such treatments. Thus, most hydraulic fracturing projects carried out in poorly consolidated rocks render unexpected results. A recent worldwide survey on net pressures by the Delft Fracturing Consortium (Papanastasiou, 1997) indicated that net pressures encountered in the field are 50% to 100% higher than the net pressures predicted by conventional fracturing simulators. The difference is yet higher for the case of poorly consolidated formations (Pak, 1997). The theory for the construction of a fully coupled elastoplastic three-dimensional hydrofrac simulator, specifically conceived for unconsolidated rocks, is presented in this paper. This novel model calculates the dimensions and changes in shape of the fracture(s) being created during hydraulic fracturing operations. No assumptions are made regarding either shape or geometry of the crack(s). Three main failure criteria are used simultaneously in this model: tensile and shear stresses, and volumetric strain. Incremental forms of the governing equations of equilibrium and fluid flow are presented. The scheme chosen for solving this problem is the finite elements method, which allows both equations to be solved simultaneously at any instant in time. Résumé La fracturation hydraulique est une technologie qu’a été utilisé pour plus que 50 ans dans l'industrie pétrolière. Elle a été utilisée au début pour stimuler les formations dure et fragile que typiquement ont des perméabilités basses et un comportement élastique à peu près linéaire. Néanmoins, un segment plus important de l'industrie stimule actuellement des formations mal consolidées; où les suppositions d'élasticité idéale et de relativement petite fuite de fluide ne se tiennent pas raison (par exemple le Golfe de Mexique, l'Afrique d'ouest, Alaska, la Chine de l'est). Dans ces roches, la stimulation avec fracturation hydraulique a été utilisée pour plusieurs années pour contrôler et résoudre les problèmes critiques de production comme les dommages de formation et d’ensablement (causé pendant les opérations de l'accomplissement et forage). Bien que prospère, l'application de cette méthode n'a pas été accompagnée de techniques robustes pour le modelage de fractures. En outre, les augmentations à long terme de production n'ont pas été souvent concrétisées. En d'autre termes, les ingénieurs ont pu, via le procès et l’erreur, éviter les majeur problèmes ‘opérationnel’ mais avec aucune optimisation de tels traitements. Ainsi, la plupart des projets de fracturation hydraulique ont été exécuté dans des roches mal consolidées et ont rendu résultat totalement inattendu. Une récente étude mondiale sur les pressions nettes par le Consortium Delft pour Fracturer (Papanastasiou, 1997) a indiqué que les pressions nettes qu’ont été rencontré dans le champ sont environ 50% à 100% plus hautes que les pressions nettes prédites par les simulateurs fracturant conventionnels. La différence est pourtant plus importante pour le cas de formations mal consolidées (Pak, 1997). La théorie de construction d'un simulateur elastoplastic d’hydrofrac à trois dimensions entièrement couplé, en particulier conçu pour les roches non consolidés, est présentée dans ce papier. Ce nouveau modèle calcule les dimensions et les changements dans la forme de(s) fracture(s) étant créé pendant les opérations de fracturation hydraulique. Aucune supposition n’a été faites en ce que concernant la forme ou la géométrie

Jan 1, 2003

The unpaved road network on a surface mine is extensive, comprising numerous roads of varying construction and material qualities with highly variable traffic volumes. Existing haul road maintenance management systems (MMS) work well for predictable traffic volumes, but for complex mine road networks, the MMS becomes onerous. This results in sub-optimal road maintenance strategies with the attendant increase in total road-user costs and reduction in service. A real-time maintenance management system was thus sought to overcome the deficiencies of existing MMS for mine roads. Since most large mines operate trucks with on-board diagnostic data collation, linked through a centralized communication and GPS backbone, it was proposed that road condition could be monitored on a real-time basis through on-board vibration signature analysis. The aim of this paper is to present the development of a real-time mine haul road maintenance management system. Following are view of mine road maintenance practices, the real-time system architecture is introduced and the results of a field trial of on-board vibration signature assessment is presented. The trial results are discussed in the light of road defect signature recognition, analysis, signature repeatability and system limitations. This approach has applicability to other situations such as a network of district roads, subject to an analysis of the economic feasibility. The paper concludes that modern technology has the potential to apply maintenance as and where needed with possible reductions in authority cost and an improvement in service provided for the road user.

Jan 1, 2003

By GA Harrison

The introduction of Extra Low Profile (XLP) mechanised equipment within Anglo Platinum is aligned with the overall New Mining Technologies strategy to focus on continuing modernization of our mining operations to achieve injury free sustainable production and cost effective mining technologies. The method allows for the introduction of a suite of XLP and Low Profile (LP) equipment in a narrow reef (1,2m) mining environment. For the first time it is now possible to achieve total trackless mechanisation at these stoping widths and XLP Breast mining has the potential to add more value when benchmarked with conventional mining and other mechanised methods. Various types of XLP equipment were tested at different sites within Anglo Platinum and this paper describes the XLP equipment evolution to-date. It concludes with recommendations on our future strategy regarding implementation and roll out of the XLP technology within Anglo Platinum.

Jan 1, 2008

By M. Matema

Paper written on project work carried out in partial fulfilment of BSc (Eng.) Metallurgy and Materials Engineering Small and large welded aluminium specimens were tested in fatigue and the results compared with design curves for aluminium in specification BS8118. Metallurgical tests were also performed on the specimens in order to correlate microscopic and macroscopic phenomena. The small-scale fatigue test results were in reasonable agreement with results in BS8118, whereas the large-scale fatigue tests showed that BS8118 is conservative.

Jan 1, 2005

By D. Nyembe, B. Mamba, Antoine F. Mulaba-Bafubiandi

Copper and cobalt are generally electro-won from their aqueous sulphate solutions. After optimised leaching of their ores, concentrates or calcine bearing minerals, the leachate is clarified and suitably purified prior to the electrolytic extraction of the metal of pursuit (Pearcy, 2006). Solvent extraction (SX) using appropriate organic solvents and ion exchange (IX) with relevant resins are known purification processes used for copper and cobalt recovery (Stanely, 1970).As zeolites in general and natural zeolites in particular, demonstrate ion exchange properties (Korkuna et al., 2005), an attempt has been made to use Southern African natural clinoptilolite in the recovery of copper and cobalt from their aqueous sulphate solutions. Initially, synthetic Co and Cu solutions were prepared. Preceded by laboratory ore leachate, plant solutions are to be used. AAS, XRF, XRD, Mossbauer spectroscopy and BET were characterization techniques used. Natural clinoptilolite was used as-received as well as acid activated; and cobalt and copper extractions were performed at room temperature.

Jan 1, 2007

By S. Jiansheng, H. Nakayama, D. Lu, A. Wang

ABSTRACT: New techniques and methods for 3D geo-mechanical model test are presented in this paper. The new model material NIOS with high density and low cost; the so-called DPSS (Discrete Principal Stress Surface) loading concept, the loading and monitoring system for the generation of the 3D initial stress field of the model test, also the special techniques and apparatuses for modelling the excavation of caverns located deep inside the model material, are developed and introduced. By adopting those new techniques, a very large 3D geo-mechanical model test with high comparability for a newly designed underground powerhouse has been successfully fulfilled. Key Words: 3D model test, underground group caverns, excavation process modeling. ZUSAMMENFASSUNG: Neue Techniken und Methoden für 3D geomechanischen Modellversuch wurden in diesem Artikel vorgestellt. Ein neues Modellmaterial mit hocher Dichte und niedrigem Preis, ein sogenanntes DPSS (Discrete principal stress surface) Ladenkonzept, ein Laden- und Überwachungssystem für die Erzeugung des 3D primären Spannungsfelds und überdies spezielle Techniken und Maschinen für das Ausbruch der tief in dem Versuchsmodell liegenden Kaverne wurden entwickelt. Bei Anwendungen dieser neuen entwickelten Techniken wurde ein sehr großer 3D Modellversuch mit großem Maßstab für ein geplantes unterirdisches Kraftwerk erfolgreich durchgeführt. Stichworte: 3D Modellversuch, unterirdischen Gruppekaverne, Ausbruchsmodellierung Résumé: le test de modèl de Nouvelles techniques et méthodes pour la géo-mécanique 3D est figuré dans ce papier. Le nouveau modèle de matériels NIOS avec la haute densité et le coût bas; la conception proposée de chargement DPSS (Discrete Principal Stress Surface), le système de chargement et de moniteur pour la génération de champs de stress initial du test de modèle, ainsi que les techniques et appareils spéciaux pour modeler les excavations de cavernes profondément localisées dans l’intérieur du matériel de modèle, sont développés et introduits. A travers l’adoptation de ces nouveaux techniques, le test de modèle de la géo-mécanique très large 3D avec la haute comparabilité pour actualiser une nouvelle étude de la centrale électrique sous-terraine a déjà accompli avec succès. Mots de clé: test de modèle 3D, groupes de cavernes sous-terraines, processus de modèle d’excavation

Jan 1, 2003

By C. G. Anderson

Throughout the world, there are many orebodies or materials which have significant value but also contain arsenic, antimony, and mercury. As regulations on the transport, exposure, disposition and emission of these elements have become more stringent; it has become increasingly more difficult to derive the values from the resources. This paper outlines the fundamentals of alkaline sulfide hydrometallurgy and its successful application to arsenic, antimony and mercury bearing ores, concentrates, by-products, and other materials.

Jan 1, 2008

By G. G. le Roux

The purpose of the investigation was to assess various options for increasing the efficiency of the conveyor belt transporting system used at 4 Belt Shaft at Lonmin?s Marikana operations. The reason for the investigation was to prevent the occurrence of a ?bottleneck? at the main ore passes delivering ore to the conveyor belt system, thus creating more fluent operational conditions. The options assessed for increasing the efficiency of the conveyor belt transporting system were: ?Variation of the conveyor speed ?Concurrent tipping from two ore passes on the belt ?Increase the available drive unit power ?Increasing the feed rate from vibratory feeders ?Change in belt width/belt specifications The report shows that the most preferable option to the current situation at 4 Belt, Lonmin, would be the option of concurrent tipping from two ore passes to the belt.

Jan 1, 2008

By R. Romano

Some topics, which difficult the effective use of RMR for dam foundations, are reviewed and a new geomechanics classification system, DMR (Dam Mass Rating), is proposed -as an adaptation of RMR- giving guidelines for several practical aspects in dam engineering and appraisal of dam foundation. On revise quelques problems qui ont fait difficile l’application du RMR pour les fondations des barrages. On propose un nouveau classification système, DMR (Dam Mass Rating)-comme un désarroi du RMR-qui donne recommendations pour quelques problèmes pratiques dans le projet et construction des barrages, et de ses fondations. Es werden einige die praxisgerechte Nutzung des RMR (Rock mass Rating) erschwerende Themen betrachtet und ein neues Geomechanisches Einteilungssystem, das DMR (Dam Mass Rating), eine Anpassung des RMR, vorgeschlagen. Daraus resultieren neue Richtlinien für verschiedene praktische Aspekte beim Dammbau und bei der Beurteilung von Dammunterbauten

Jan 1, 2003

By J. J. Stacey

Large mining companies generally follow the distributed ownership corporate model, with a board of directors responsible for decisions that affect both shareholder value and stakeholders of the company. The board is simultaneously responsible for setting the culture and values of the corporation, which drive performance and priorities. Companies listed on the Johannesburg Securities Exchange (JSE) commit to sustainable development in various ways, either by virtue of implementing the King Code of Governance 2009 (King III) and/or through their own public reporting on social and environmental matters. Many mining companies make public statements regarding their support for environmental stewardship, ethical behaviour, and fair treatment of communities. It is a local, regional, and indeed, global phenomenon that companies fail to deliver on these statements. Research was carried out through the Institute of Directors of Southern Africa in 2007, and followed up in 2012, regarding directors? understanding of sustainable development issues, the relative priorities, what is needed for ?radical change? to effect sustainable development, and what enables or constrains the latter. Pertinent findings of both surveys are presented in this paper, and it is suggested that ?on-the-ground? performance may be indicative of the nature of leadership and decisions in the topmost ranks of the company. The results indicated that environmental concerns fall consistently below social issues. Financial capital ranked most important, and while environmental issues are recognized as being of strategic concern for the long-term, they ranked as being the lowest importance of all ?Five Capitals? (Financial, Manufactured, Social, Human, and Natural). Social capital ranked second lowest, with black economic empowerment being the only high-priority social issue. There is also evidence that certain companies within the mining sector fail to recognize their absolute dependence on natural resources. Much is made in academic and popular literature of the need for a new type of leadership for the radical shift to sustainable development: at company level this implies therefore a new type of director. The research found that only 14 per cent of directors felt that board decisions are consistent with their personal values; while intentions are strong to behave ethically and serve sustainable development, actions to give effect to these intentions lag significantly. Respondents indicated that the top impediments to courageous leadership for sustainable development related to personal issues of maintaining the image of being a director, fear of appearing weak, fear of being a lone voice, and bowing to board-colleague peer pressure.

Jan 1, 2014

By Stefan Basista, Janusz Tomala

Modern constructions of electric ferroalloy furnaces are still based on applying in the lower "liquid" areas the standard carbon materials. What can be illustrated by the experience from several years, in the part of tap hole, hearth walls and bottom, is that so-called carbon or semigraphite microporous materials are successfully being applied. These materials, compared to the standard carbon, give better resistance to the attack by liquid metal and other wear factors. Generally this group includes materials characterised by considerable share of pores of diameters below1µm (significantly exceeding 90% of total porosity). The microporosity increases the resistance to the infiltration of the liquid metal. The effect of microporosity can be obtained by introducing silicon (or its compound) additive to materials based on electrically (or gas) calcined anthracites, electrographite and binder. Moreover, by introducing other ceramic additives, the microporous materials are more resistant to dissolution by the liquid metal. Observing the trends of "improving the materials" in the last years, it is clearly seen that the share of non-carbon additives is bigger and bigger, so we can reasonably speak of rather carbon-ceramic materials. In this paper, the survey of the most important quality criteria, which must be met by the carbon furnace linings, as well as the new testing methods will be presented.

Jan 1, 2007

By J. Kerr

The first stage of the development of a new modified 201-type low nickel austenitic stainless steel is described in this paper. The alloy is intended for use as a structural alloy, and so requires a yield strength >400MPa as well as acceptable weldability and toughness. The low nickel content will give a lower material cost in comparison to more conventional austenitic grades, and the processing route is required to be similar to that of Type 304 to keep the processing cost low. The base alloy was designed using empirical methods developed for stainless steel, and the properties of the base alloy were verified using a range of small-scale melts. The base alloy had a 0.2% proof strength of ~320-400MPa, and so it is planned to use V additions of ~0.15% to bring about precipitation strengthening in the hot rolled condition, so raising the alloy?s proof strength above the 400MPa minimum.

Jan 1, 2004

By A. Cichowicz

In this study, techniques used to design earthquake-resistant structures are applied to the deep-level mining environment. Earthquake engineers seek to identify the cause of potentially damaging resonance, and design or reinforce structures to reduce these effects. Similar techniques have been used to analyse the dynamic behaviour of the rock mass surrounding a stope in a deep South African gold mine. A three-dimensional seismic array installed in a stope at TauTona Mine (previously Western Deep Levels, East Mine) provided an opportunity to examine the evolution of the wave field close to an underground opening. A set of three-component geophones installed in a borehole above the panel revealed the development of surface waves as wave fronts reached the excavation, and an array of vertical component geophones fixed to the hangingwall provided a two-dimensional map of site effects. While the collected data do not include damaging seismic events, quantitative analysis enabled phenomena which could lead to damage, to be recognized. In the vicinity of the excavation, the energy of the seismic signal is generally transformed from high frequency to low frequency. It was found that seismic events with relatively high corner frequency (150 Hz?200 Hz) usually excite several modes of vibration (30 Hz to 110 Hz), while events with low corner frequency (30 Hz?50 Hz) do not always excite higher modes of vibration in the structure. This implies that the rock mass around the excavation is a complex medium, and should be studied using the multi-degree-of-freedom model. A strong structural effect (due to the excavation shape) was revealed as a low frequency coda wave (at 40 Hz and 60?70 Hz), well developed on the skin of the hangingwall. A strong site effect was revealed by changes in signal properties between hangingwall geophones, exhibiting strong resonances around 160 Hz and in the range 200 Hz to 300 Hz.

Jan 1, 2000

By R. Zivojinovic, S. Vujic, T. Tanaskovic

The problem of determining the optimum exploitation life of machinery, namely the optimum time for machinery and equipment replacement, represents a complex and highly responsible engineering task. Taking into consideration the situation prevailing at coal pit mines in Yugoslavia, the tasks of this class are very complex and difficult. To make a decision on replacement of capital equipment and machinery, such as bucket wheel excavators within the mentioned systems, understands a management task of utmost responsibility. It requires high professional and analytical knowledge as well as the reliable arguments, based on multidisciplinary professional approach. In this paper, the authors present their views on the problem of establishing the optimum exploitation life of bucket wheel excavators, offering an algorithm, based on dynamic programming, as a solution. Keywords: Bucket wheel excavators, exploitation life of machinery, optimization, operations research, theory of replacement, dynamic programming

Jan 1, 2003

By D. N. Ferguson

The separation of certain minerals by electrostatic techniques can be difficult due to their similar electrical conductivity, and any technique to improve this can be useful in certain difficult separation applications. Triboelectric differences between mineral scan result in certain minerals acquiring small positive or negative charges prior to inductive electrostatic separation. By changing the polarity of inductive separation, relative changes in mineral recovery can be observed, which may be beneficial. In this brief study a JKTech mineral liberation analyser (MLA) was used to evaluate the effect of polarity change on selected minerals present in the Richards Bay Minerals deposit, and an approximate triboelectric series based on this behaviour is presented.

Jan 1, 2010