Search Documents

By S. T. L. Harrison, M. A. Fagan-Endres, M. D. Odidi

This paper investigated the ability of eight common hydrodynamic models – tanks in series (TIS); three compartmental model configurations (Comp-1, Comp-2 and Comp-3); advection dispersion (AD); piston exchange (PE); piston exchange-diffusion variant (PE-D) and piston dispersion exchange (PDE) – to simulate residence time distribution (RTD) data generated from tracer tests conducted on a packed bed composed of different size fractions of malachite ore. The chosen materials were packed into 0.1 m internal diameter columns to a depth of 0.155 m and drip irrigated at 5.11 L/ m2.h. The four size fractions tested were: 1 – 2 mm, 2 – 2.8 mm, 4.75 – 5.6 mm and 13.6 – 16 mm. Step-up tracer tests were conducted using potassium chloride. The results showed that an increase in the particle size of the malachite ore had little effect on overall bed porosity but resulted in significantly lower values of liquid holdup. Two of the monoporosity models tested, TIS and Comp-2, were the most affected by the changes in bed size fraction due to their inherent inability to cope with high degrees of non-ideal flow present in the larger particle systems. The dual porosity models performed relatively better with the dominant trend being a reduction in dynamic to total liquid holdup as particle size increased. Of all the models tested, the PDE and TIS models were the best and worst performers respectively, with R2 values averaging at 0.997 and 0.679 across all experiments respectively. Though the Comp-1, Comp-3 and PE-D models also performed well, the addition of the dispersion coefficient to take the axial spread of fluid molecules into account added a layer of complexity that allowed the PDE model to perform relatively better than the other dual porosity models. Keywords: Heap leaching, packing material, hydrodynamics, malachite, PSD, modelling

Jan 1, 2020

By A. Fouchee, N. Naudé, K. Schommarz

"This article presents laboratory test work conducted on an African haematite ore to determine the influence of the flotation pulp pH on the final iron grade and recovery. Results show that a combination of an isodecyl ether propylene amine/amino acetate and 1,3-propanediamine, N-(3-(C10-C16-alkyloxy)propyl)-derivatives collector is suitable for separating haematite from quartz. Higher iron grades were obtained at pH levels between neutral and pH 9. This underlines the importance of the surface charge effect of the ore on its flotation characteristics. The results serve as good baseline conditions for further optimization. IntroductionBeneficiation of iron ore by flotation is widely used in Brazil, India and China. In Africa, however, this practice is not yet commercially developed.The aim of this test work is to serve as a starting point by establishing suitable pH conditions for the development of a practically implementable reagent suite, which will then be included in a larger beneficiation circuit for producing high-grade iron ore sinter feed.In the literature, African iron ore types are graded as low-grade (60.0–62.9% Fe; 8.6– 12.5% SiO2 and insolubles), high-grade (66.0– 69.9% Fe; 0.8–4.5% SiO2 and insolubles), and meduim-grade as the remaining portion (Astrup et al., 1998). The low-grade ore used in this work contains less than 60% Fe.For Brazilian ores consisting of a combination of haematite and quartz, it is common to use corn starch as a depressant and ether amine blends as collectors with additional frothing characteristic (Araujo et al., 2005). Work by Turrer and Peres (2010) shows the possibility of using other depressants successfully as well.The main mechanism of the reverse flotation of quartz from iron ore is based on the electrostatic theory of flotation. This is due to the strong pH dependence of the zeta potential of the mineral edge planes on silicate particles (Fuerstenau and Pradip. 2005)."

Jan 1, 2016

By E. Molobi

"Studs are rods threaded on both ends and are used as mechanical fasteners for two or more components. Stud finds usage in industries such as automotive, construction and aviation. The advantage of studs is that they allow for disassembly of components during maintenance. Studs are continuously subjected to both tensile and shear stresses, depending on the application, therefore they should be manufactured from suitable materials that are capable of withstanding all these external forces. Studs are sometimes manufactured from re-sulphurized steel due to its improved machinability; however, there is a certain limit on the amount of sulphur, above which failure may occur. Premature failure of studs has been a common problem, but failed studs are commonly replaced with new ones without conducting failure investigations. The present work investigates the premature failure of two re-sulphurized steel studs used on a rocker arm assembly and recommends alternative materials. The investigation was carried out by conducting visual examination, microstructural analysis, hardness measurements, chemical analysis and a detailed scanning electron microscopy (SEM) investigation on the fracture surface.IntroductionTwo rocker arm studs used on a 16-cylinder diesel locomotive engine failed prematurely after being in service for less than 5 months. The rocker arm studs had a life-cycle of 5 years. The studs were manufactured from resulphurized steel. The paper aims to establish whether re-sulphurized steel is applicable for the manufacture of studs in the automotive industry.BackgroundLocomotives are classified as either electric or fuel-powered. Diesel locomotives are an example of fuel-powered locomotives. This type of locomotive uses a diesel engine as a means for propulsion. An engine converts chemical energy into mechanical energy required for traction. In an internal combustion engine a rocker arm is an oscillating lever that conveys radial movement from the cam lobe into linear movement to open and close poppet valves of cylinders (Husain and Sheikh, 2013). The rocker arms are secured on to the cylinder head by rocker arm studs."

Jan 1, 2016

By D. Orynbassar, N. Madani

This work addresses the problem of geostatistical simulation of cross-correlated variables by factorization approaches in the case when the sampling pattern is unequal. A solution is presented, based on a Co-Gibbs sampler algorithm, by which the missing values can be imputed. In this algorithm, a heterotopic simple cokriging approach is introduced to take into account the cross-dependency of the undersampled variable with the secondary variable that is more available over the entire region. A real gold deposit is employed to test the algorithm. The imputation results are compared with other Gibbs sampler techniques for which simple cokriging and simple kriging are used. The results show that heterotopic simple cokriging outperforms the other two techniques. The imputed values are then employed for the purpose of resource estimation by using principal component analysis (PCA) as a factorization technique, and the output compared with traditional factorization approaches where the heterotopic part of the data is removed. Comparison of the results of these two techniques shows that the latter leads to substantial losses of important information in the case of an unequal sampling pattern, while the former is capable of reproducing better recovery functions.

Aug 1, 2021

By R. MacRosty, R. Pula, P. Gebski, W. Braun

"This paper provides a progress update on three tapblock monitoring technologies that Hatch has been developing with our clients for non-ferrous smelting furnaces.The Tapblock Diagnostic System (TDS) is an advanced on-line monitoring system that uses temperature data along with embedded thermal model results to evaluate the condition of a tapblock over its campaign life. Hatch recently installed a second Tapblock Diagnostic System, some details of which are provided in this paper.The Tap-hole Acoustic Monitoring (TAM) system is installed on water-cooled copper tapblocks and uses the noise from the tapping channel to provide a qualitative indication of wear and deterioration of the tapping channel refractory. In addition, TAM can be used to monitor drilling and lancing performance, and potentially could also be used in the future as a guide for automatic drilling and lancing systems (Sadri et al., 2008).The third technology is the use of fibre optic sensors to measure temperature on the hot face and in the tapping channel of a tapblock. Fibre optic technology allows installation of numerous sensors in key locations where they are very sensitive to tapblock condition and also provide more extensive spatial coverage than is possible with traditional instruments. This paper provides an update on our efforts to address issues with premature failure of the sensor cables due to corrosion, and also converting the vast amount of data from the sensor cable into information that can be used by furnace operators."

Jan 1, 2014

By J. Hadjigeorgiou, G. Knox

Since their introduction in 2010, paddled energy-absorbing rockbolts have been widely used in seismically active hard rock mines. This paper provides new data and reviews previous work to quantify the performance of paddled energy-absorbing rockbolts under controlled laboratory conditions. Of significance is the realization that the typical split location in impact tests, at the centre between two paddle anchor points can at best provide an upper limit value. This inherent variability in performance under different testing configurations should be acknowledged and taken into consideration in the design of ground support in seismic conditions. This paper discusses the reduction in capacity of paddled rockbolts as a function of loading angle from a maximum value during axial tests (0° loading angle) to the lowest value during pure shear (loading angle of 90°). A significant reduction in displacement capacity is observed as the loading angle changes between axial (0°) and 40°. Beyond a 40° loading angle up to shear (90°) loading the reduction in displacement capacity is less significant. Due to the variances in the capacity observed through the variance of the testing configuration: loading mechanism, direction of loading, location / presence of a discontinuity, it must be recognized that results from laboratory-based testing are not independent of the testing configuration. This should be acknowledged when extrapolating anticipated performance in the field.

Oct 9, 2024

By P. J. Petit

"The complex planning required to achieve any planned production yields multiple and dissociated responses over the life of project (LOP). The customary decision-making process negates the possibilities of developing optimized and integral solutions from operating levels up to business and strategic levels. This results in an inefficient project or overall underperformance of the operation.In the project setting, disconnected trade-offs and improved performance studies become inadequate, because they are site-specific and use only a few comparative parameters. They are often based on a small data-set.Decisions taken to achieve overall objectives require the correct determination and dissemination of key performance indicators (KPIs). The KPIs indicate efficiency in operation, whereby the marginal rate of technical substitution corresponds to the rate of production. It is the necessary condition for optimization. Performance realization for sustainability follows optimization modelling, the latter often being presented with financial results such as business net present value (NPV). It considers techno-financial constraints and provides a strategic and aligned outlook of KPI decisions for an enhanced and integrated outcome.This paper explains a mining case study that is rendered efficient, and through business optimization (BO) short-term and sustainable targets are reached. Business optimization increases the NPV by 14.7%. This is achieved by challenging conventional decision-making associated with maximizing business value by including environmental externalities within the LOP."

Jan 1, 2016

By J. D. Swanepoel, S. Horn, C. J. Badenhorst

Diesel particulate matter (DPM) is the particulate component of diesel exhaust, which includes diesel soot and aerosols. When released into the atmosphere, DPM can take the form of individual particles or chain aggregates, with most in the invisible sub-micrometer range of 100 nanometres. The main particulate fraction of diesel exhaust consists of fine particles and because of their small size, inhaled particles may easily penetrate deep into the lungs. The rough surfaces of these particles make it easy for them to bind with other toxins in the environment, thus increasing the hazards of particle inhalation. DPM is a significant health hazard in underground mining operations, where the use of dieselpowered equipment in confined spaces can lead to high levels of exposure among people working in these environments. Classified as a carcinogen by the International Agency for Research on Cancer (IARC), DPM has been linked to severe health effects, including respiratory and cardiovascular diseases, as well as an increased risk of lung cancer. Effective management of DPM is essential not only for protecting people’s health but also for ensuring regulatory compliance, maintaining operational efficiency, and safeguarding the long-term viability of mining companies.

Mar 5, 2025

By E. Y. Baafi, H. Fan, W. Zeng

We present a discrete event simulator, TSJSim (Truck-Shovel JaamSim Simulator), for evaluating the stochastic and dynamic operational variables in a truck-shovel system. TSJSim offers four truck allocation strategies: Fixed truck assignment (FTA), Minimizing shovel production requirement (MSPR), Minimizing truck waiting time (MTWT), and Minimizing truck semi-cycle time (MTSCT) including the genetic algorithm (GA) optimization and the frozen dispatching algorithm (FDA) optimization rules. Multiple decision points along the haul routes for all the trucks close to the decision points were included in the model. The simulation results indicate that the trends associated with production tons and queuing time utilizing the four truck allocation strategies (MSPR, MTWT, FDA, and GA) all demonstrated similar patterns as the fleet size varied. As the system fleet size increased, the system production tons under these strategies at first increased significantly and then remained relatively constant; the queuing time relating to these strategies showed a positive relationship with the system fleet size. The bunching time decreased when the truck allocation strategies were applied in the model. In the simulated truck-shovel network system with multiple traffic intersections, by assigning the trucks at the intersections, both productivity and fleet utilization increased.

Dec 13, 2022

By M. Royle, A. Bloem, R. Uken

Rock mass damage induced by mining increases the fracture frequency and joint aperture width in the pit walls and rock mass behind open pit mine slopes. The depth and intensity of this mechanical damage relative to the pre-mining state is not well understood and yet is a major factor in the development of slope stability models and operational guidelines. The induced damage can be partitioned into domains or zones. The blast damage zone is essentially a ‘free flow’ rock mass volume, which transitions quite rapidly into the excavation damage zone, which extends beyond that. In both zones, transient high in situ water pressures are often linked to unstable slope conditions. Whereas rock damage can enhance passive depressurisation in the rock mass, high infiltration rates on the other hand, as one could expect during rainstorm events, will decrease slope stability within the dilated pit rock mass, especially in the blast damage zone-excavation damage zone, by increasing pore pressures for short periods of time. Ice jacking and freshet are additional factors to consider in (sub) arctic environments and can be exacerbated by unfavorable rock fabric orientation. On a local scale, brittle deformation damage zones, in the form of faults, can contribute to slope instability, or enhanced stability because of slope depressurisation, depending on their location and orientation relative to the pit shape and the water sources. In this study, the shapes of the damage zones and their anticipated impact on infiltration and/or passive depressurisation are considered for different pit morphologies, rock mass conditions, in situ stress, and hydrogeological settings. Some unusual hydrological situations, like mining towards rivers and lakes and the potential effects on pore pressures, are also considered. This investigation has resulted in the development of a method to adjust initial hydraulic conductivity values used to estimate transient pore pressure conditions found in rock masses exposed in different pit morphologies and stress regimes as well as discontinuities’ orientation relative to open faces within the open pit mine. The changes in K values and pore pressures can then be used to determine hydrogeological influence more accurately on future pit slope stability.

Sep 1, 2025

By H. Dudycz, A. Skoczylas, P. Stefaniak, P. Pyda

In the era of Industry 4.0, technologies such as Big Data (BD) and the Internet of Things (IoT) play a key role, especially for multi-site manufacturing companies. In such companies, the challenge is to collect and process massive amounts of data from industrial devices and extract key information from this data in real-time for ad hoc decision-making. The ability to analyse data from industrial devices translates directly into streamlined production processes, cost optimisation, prevention of unplanned events, and safety during operation. In this context, particular attention should be paid to Big Data Analytics (BDA), whose main source is the Industrial Internet of Things (IIoT). The purpose of this paper is to propose an IT system architecture incorporating BD and the IoT for a mining company. The paper presents results from a literature review focusing on available BD and the IoT solutions for industry (mining in particular) for the purposes of the acquisition, integration, and advanced analysis of data. The advantages and disadvantages of the different solutions were indicated and gaps in the accessibility to dedicated functionality are identified. Based on the analysis of a multi-site mining company, the main challenges faced by such companies planning to implement BD and IoT solutions are identified. Also, a proposal for an IT system architecture incorporating BD and IoT for a mining company is described in the paper. The contribution of the article consists of the identification of the challenges faced by mining companies planning to implement BD and the IoT solutions, and the proposal of an IT system architecture that allows BDA whose main source is the IIoT.

Sep 1, 2021

By k. Lebecki, S. Trzcionka

The prototype and test results of the instrument for quick determination of incombustible content in deposited dust as a protection against coal dust explosion propagation are presented. Presently existing methods do not permit to obtain quick information about incombustible content, needed for the proper protection of workings. As the operating principle for the e instrument the dependence of reflection of infrared radiation intensity on incombustible content in the sample is chosen. The construction is based on the modern electronics. The measurement will be done at the sampling site. The range of the instrument is 0-100% of incombustible, direct reading, autonomous supply, weight no more than 0.5 kg, and is intrinsically safe according to EN Standards. During the Conference the instrument will be commercialized.

Jan 1, 2003

By S. J. van Wyk, A. S. H. Haagner

Land rehabilitation transcends the mere establishment of vegetation across disturbed landscapes; it should be conceptualised as a specialised ecological reconstruction process. This process necessitates a long-term perspective on the success of land repurposing. It requires a continuum of inputs specified and managed by a dedicated and qualified custodian to ensure the sustained economic viability and ecological sustainability of the land. Based on the authors’ combined experience and field observations over more than five decades, they advocate for an urgent shift away from traditional land rehabilitation practices toward a paradigm centred on land capability reconstruction and active stewardship. The prevailing rehabilitation culture has overly simplified the process to a mere revegetation exercise, which is fundamentally incompatible with the comprehensive requirements for sustainable land capability. While the regulatory framework provides valuable guidance for obtaining a mine’s social license to operate, a paradigm reset is essential. Mining companies must prioritise rehabilitation quality, set achievable sustainability goals, and establish clear pathways and milestones to meet relinquishment criteria. Currently, the status quo view—a model reliant on outsourced contracting and agricultural approaches—is that mine rehabilitation is a one-time intervention rather than a complex, systemic, and long-term process. This perspective presents significant challenges, as the success of ecological interventions can only be accurately assessed over extended timeframes, often spanning decades. Shortsighted rehabilitation specifications, coupled with practitioners operating within agricultural decision frameworks, frequently overlook the necessity for integrated rehabilitation expertise and the scientific foundation essential for designing and implementing effective ecological outcomes. A lack of long-term monitoring information impedes the required adaptive management of rehabilitated systems and, therefore, delays the transition towards final land use. This short approach costs the mining industry millions annually, often without recognising the inadequacies in long-term liability mitigation and the substandard ecological success achieved. The disconnect between procurement processes, the qualifications of service providers, and the unclear pathways to relinquishment can impede successful rehabilitation outcomes, frequently undermining progress toward sustainability milestones. Unless there is a fundamental reset of the land rehabilitation culture, pursuing sustainability will remain an elusive and perhaps impossible objective. Consequently, mining companies may hesitate to fully commit to sustainable land rehabilitation practices, as the prospects for relinquishment and final closure remain uncertain at best.

Apr 25, 2025

By P. N. Harris

The Colloquium on 'Recent Mining and Metallurgical Developments in the Orange Free State' was held at the Civic Centre in Welkom on the 4th and 5th May, 1983. The Chairman of the Orange Free StatejKlerksdorp Branch of the Institute and Acting General Manager of Unisel Gold Mining Company, Mr D. A. Parfitt, opened the proceedings, and Professor A. N. Brown gave the welcoming address. Mechanization of mining The South African Institute of Mining and Metallurgy is to hold a one-day colloquium on 'Developments in the Mechanization of Mining Operations' during September 1984. Surfac,e mining and quarrying The Second International Surface Mining and Quarrying Symposium is being organized by The Institution of Mining and Metallurgy in association with the Institute of Quarrying.

Jan 1, 1983

By Donald J. Murdock

Column flotation has been developed over the past ten years as an alternative to conventional flotation. It has been used mainly in the cleaning applications of sulphide flotation, where its ability to wash the froth of entrained gangue and produce a higher-grade product has given it a distinct advantage over other technology. The benefits of column flotation can be summarized as follows: Improved concentrate gradeby 2 to 5 per cent . Significantly lower operating costs . Savings in capital investment . Superior control. Since the initial development of the equipment, a number of design improvements have been developed that now form the basis of the Cominco column-cell design. The purpose of this article is to discuss some of those design innovations, and present some typical industrial results.

Jan 1, 1991

By H. Karabulut, S. Gündüz, K. Karacif, M. A. Erden

The corrosion properties of iron-based composite materials containing graphite and silicon carbide (SiC) reinforcement were investigated. The effects of silicon carbide reinforcement were investigated by adding 0.5% graphite and 1%, 2%, and 4% SiC. A powder metallurgy method was used to produce the composite samples. Iron, graphite, and silicon carbide powders were blended for one hour with a threeaxis mixer and then unidirectionally pressed under a pressure of 750 MPa. After pressing, the composite materials were sintered at 1100°C for one hour. The corrosion properties and microstructure, density, and hardness properties of the composite materials that can affect the corrosion properties were also investigated. It was determined that the pore ratio and hardness of the composite material increased, and corrosion resistance decreased, with increasing silicon carbide content.

Jun 2, 2022

The 99th Annual General Meeting of The South African Institute of Mining and Metallurgy was held in the Gold Room, Transvaal Automobile Club, 60 5th Street, Lower Houghton, Johannesburg on Wednesday, 14th August, 1996. Obituaries The President announced the death, during the year, of the following members: Life Fellows H.L. Munro, H.S. Simpson, P.L. Ward Fellows I.M. Hossy, A.E. O'Meara Retired Fellows E.A. Arvidson, R.F. Bourne, F. Hawke, W. Lloyd, J.M. Meyer Members J. Allen, P.A. Boardman, L.M. Jacobs, G.F. Marx, G.D. Perry, R.W. Spraggs Retired Member M. Milner Associate I. Pieterse. In memory of the deceased and in sympathy with the bereaved, all rose and observed a moment of silence.

Jan 1, 1996

By P. R. Beeley

Metal founding - a modern perspective The recent development of metal founding is reviewed in the context of basic requirements for the successful manufacture of cil;5ti,ngs.Progress has been related to the two interdependent fields of process technology and product characteristics. . After a brief review of the growth of the traditional industry. various features of the modern industry are discussed. Reference IS made to current trends in process technology and to the introduction of new techniques affecting production engineering, product quality. and the general nature of the industry. Metallurgical aspects of metal founding are considered, and modern techniques for the control of casting conditions are examined. These aspects are related to the structure and quality of cast metal and to the development of newer types of cast material and product.

Jan 9, 1976

The aspect ratio (mill diameter/mill length) of autogenous and semi autogenous mills varies widely and can be as high as three or as low as 0.5. The literature on the subject of what effect aspect ratio has on grinding mill performance or energy efficiency is almost non-existent. However, at the design stage of many grinding circuits the subject is often vigorously debated amongst metallurgists. In this paper the performance characteristics of mills with different aspect ratios are examined to determine whether process performance characteristics are a function of aspect ratio and whether high aspect ratio mills are any more or less energy efficient than low aspect ratio units. Data from both pilot and full-scale mills are used for this purpose in open and closed circuit configurations.

Jan 1, 2007

By N. G. Cook, N. C. Joughin, A. J. A. White

The rate of face advance in the gold mines is between 3 and 10 m a month, with a median value of about 5 m a month; it follows that faces are blasted less frequently than is planned. There are many advantages in the use of short holes for stoping to give face advances of from 0,7 to 0,8 m per blast. This has the potential for so increasing the frequency of blasting that monthly rates of face advance could be improved significantly. Cleaning with face scrapers is too slow to permit the maximum achievement of a complete clean, drill, and blast cycle for each shift. Short-hole blasting, combined with the use of mechanical conveyors for face cleaning, offers the possibility of completing two such cycles each day, yielding monthly rates of face advance of up to 35 m. Experiments aimed at developing safe, unitized explosive charges well-suited to produce reliable face advances of 0,7 to 0,8 m per blast under a wide range of gold-mining conditions have been notably successful. A novel method of assessing the effectiveness of a blast based on the percentage of holes that leave socket lengths of 5 cm or less was used. Unitized charges of 60 per cent Ammon gelignite, 600 mm long by 25 mm in diameter, appear to be near optimal. The explosive is de-sensitized to obviate detonation by chance mechanical impact, but requires only a 6D detonator for initiation; it has good water-resistance. Means have been developed for producing these cartridges automatically, but the necessary machines will have to be built specially and the cartridges are not yet available in large numbers. A second experiment by way of an extended pilot production trial using these cartridges in holes 0,9 m long is now under way. Preliminary results indicate that drilling and explosive efficiencies and productivity are well above average, even though face scraping is being used. Unitized charges of this type are likely to prove even more advantageous when mechanical face conveyors come into use.

Jan 1, 1975