Search Documents

By I. Druce, C. Li, T. Qu, J. Dong, W. Y. Xinchao, V. Nkuna

CITIC Heavy Industries has a large installed base of grinding equipment throughout Africa in different configurations, including high-pressure grinding rollers with ball mill and semi-autogenous ball crusher. The total installed power of CITIC’s mills exceeds 430 MW. In this paper, we compare several typical grinding circuits of copper in Africa with about 15 kt/d throughput based on ore properties, process selection, equipment sizing, and key equipment capital and operating costs. Actual operating performance is also introduced. The comparison for the following mine sites provides a general reference for the selection of copper grinding circuits with this approximate throughput: Kamoa-Kakula Copper Mine with high-pressure grinding rollers with ball mill circuit, and Deziwa and Sicomine Copper-Cobalt Mines with semi-autogenous ball crusher circuits

Jan 1, 2023

By S. Zhang, Z. Hua, D. Feng, X. Tong, X. Xie

The separation and beneficiation of low grade collophanite has long been a technical challenge in phosphorous production. It requires the joint efforts of process design, reagents optimisation and operational control. In this study, the statistical response surface method was applied for determining the optimum reagent dosing in the flocculate flotation of a low grade (18.59%) collophanite ore. The dosage of three reagents, including a pH regulator (Na2CO3), depressant (Na2SiO3) and flocculant (modified starch), were input parameters of the modelling design. Two quadratic mathematical models were derived for prediction of grade and recovery based on the statistical design. Statistical analysis of the experimental results validates the reliability of the models. Through further calculation, the optimum dosage of the three reagents were found to be 3,020g/t Na2CO3, 1,990g/t Na2SiO3 and 880g/t modified starch, with which a maximum recovery of 75.81% and P2O5 grade of 30.08% was obtained from flocculate flotation test. Keywords: Process optimisation, modelling, froth flotation, collophanite ore, response surface methodology

Jan 1, 2020

By Z. Khan

Iron, in the form of steel and stainless steel, is the most commonly used metal in the world. Plain steels corrode and oxidize easily, while stainless steels exhibit improved corrosion and oxidation resistance. It has been found that rare earth metal (REM) additions, such as cerium and erbium, result in the improvement of the abovementioned properties in iron-containing compounds. Gadolinium is a REM, however, there is very little information available on the influence of gadolinium on the microstructure and mechanical properties of iron-containing compounds. Thus, the purpose of this research project was to determine the influence of gadolinium additions on the microstructure and mechanical properties of mild steel and 316 stainless steel. Ten alloys were produced for the purposes of this research. Five of the alloys had a base composition of mild steel while the remaining five had base composition of 316 stainless steel. The alloys for each of the base composition contained gadolinium additions of 0.1, 0.5, 1.2, and 5 weight per cent. The as-cast and the cold-rolled alloys were analysed. The alloys responded well to the cold-rolling with the exception of the 5 weight per cent gadolinium mild steel and stainless steel alloys. These alloys were extremely brittle and underwent a significant amount of cracking during the cold rolling process. A microstructural analysis of the alloys was conducted using a light optical microscope, while the chemical analysis of the alloys was conducted using energy dispersive x-ray spectroscopy (EDS). The resulting microstructures and EDS analyses revealed that the gadolinium displayed minimal solubility in the ferrite matrix of the mild steel alloys and minimal solubility in the austenite matrix of the stainless steel alloys. Instead the gadolinium formed as an interdendritic secondary phase in both alloys. EDS analysis revealed that the secondary phase in both alloys was gadolinium-rich. Vickers microhardness tests conducted on both alloys revealed that the alloys were composite-like, with a hard, brittle gadolinium-containing compound dispersed throughout a softer, more ductile matrix. The corrosion resistance of the alloys was determined through potentiodynamic anodic polarization tests. Two solutions were used for the corrosion rate tests: a 0.5 weight per cent NaC1 solution and a 0.5 M H2SO4 solution. The results from the mild steel alloys revealed that in both the solutions, the corrosion potentials and the corrosion resistance of the alloys increased with increasing gadolinium concentration up to 1 weight per cent. The corrosion rate test results from the stainless steel alloys revealed that the passivation current density and corrosion resistance of the alloys increased with increasing gadolinium concentration in both solutions. The oxidation resistances of the mild steel and stainless steel alloys were determined through the use of a Netzstch Simultaneous Thermal Analyser. For both the mild steel and the stainless steel alloys, it was found that the oxidation resistance of the alloys increased as the concentration of gadolinium increased when compared to the as-received mild steel and stainless steel samples. This could be due to a strongly adhering gadolinium oxide scale that formed on the surface of the alloys and resulted in the protection of the mild steel and the stainless steel.

Jan 1, 2012

By B. Genc

Improving student success rates without compromising the quality of graduates is one of the biggest challenges expanding university programmes are facing in South Africa. By establishing a new Mine Design Laboratory (MDL) for higher learning in Mining Engineering, the School of Mining Engineering at the University of the Witwatersrand (Wits Mining) has achieved one of the important goals in its five-year strategic plan, i.e. to improve throughput in all years of study. Although the establishment of the laboratory has been a costly exercise, results so far have shown an improved success rate in most subjects taught in the facility. This paper outlines the design and equipment of the laboratory, the facilities incorporated, a comparison with the old laboratory, and the performance of students?all of which indicate how important it is to have proper facilities to improve the teaching of, and learning by, large classes. Through this initiative, Wits Mining has taken an important step that will contribute to addressing the skills shortages in the mining industry.

Jan 1, 2012

By M. Le Roux, Q. P. Campbell, N. Hughes

Water plays a significant role in minerals processing; this is especially true in coal preparation where water-based beneficiation is widely accepted and consistently delivering sharp separation efficiencies and high product yields. Although wet processing is favoured, the substantial process water requirement may prove this impractical and unsustainable in some parts of the world. Many coal-rich regions (including South Africa) have experienced severe water shortages. Coupled with the effects of drought, some countries experience freezing winters from which problems related to frozen process water and machinery may arise. Hence coal preparation practices will soon have to adapt, irrespective of the technical and economic feasibility offered by the currently employed water-based methods. As a result, extensive research into the development of dry methods for effectively beneficiating coal has progressed. This review paper intends to provide a collection of the relevant information pertaining to dry coal processing globally, and aid in understanding the applicability, performance, success or failure thereof. The methods available for dry materials preparation, with special regard to those applicable for coal beneficiation, are detailed in terms of principle, applicability, limitations and performance. Dry coal beneficiation has potential to aid the current wet-based methods with some considerations to possible limitations set forth by coal geology, application, product specification, particle size distribution, moisture, efficiency, capacity and cost. These methods may be established in future, especially in the arctic, arid and under-developed regions through new plant installations, expansions and small mines processing. Keywords: Dry coal processing, preparation, cleaning, beneficiation

Jan 1, 2020

By A. M. Croll

The efforts to mechanize narrow reef tabular orebodies unique to this country, are not new. They began in the early 1900s and have over the last century seen varied rates of progress and success. Efforts to mechanize with the use of scraper winches can be regarded as a success. The scraper winch replaced the hand lashing of ore and development waste into hoppers. The initiatives by Anglo Gold and the then JCI to implement trackless mining equipment into these environments had limited success but in general were looked upon as a failure?at least this is the perception. The Chamber of Mines Research Organization (COMRO) in conjunction with various mining houses tried to make a success of the impact ripper. Diamond wire cutting of the stope face is another, which has been tried and tested. The use of high-pressure water to cut rock has also been trialed. These attempts, amongst others, are just a few of the efforts that have not been successful in the quest to make life at the face safer, more productive and easier for our employees. Against the backdrop of an emerging South Africa, the associated high expectations of historically disadvantaged people within the country, a strong rand, demands for better safety, lower cost of production and more efficient operations, mechanization has the chance to make a difference to Anglo Platinum?s business. Mechanization has certainly changed the way other commodities such as coal, base metals and diamonds are won from the earth. Mining?s image is still one of people crawling around in stopes?a dirty, ?low-tech? business. Anglo Platinum?s latest journey to mechanize its underground operations began in earnest in1998 and has enjoyed some successes and failures. The opportunity to change the way mining is done within the company is there. Technologies are evolving, and the implementation of mechanization can certainly assist with the achievement of the goals referred to above. When mechanization commenced, targets were set for the company to achieve but these have been revised in the light of recent events relating to the strengthening rand and a slow-down in expansion plans. However, the intent to mechanize appropriately in Anglo Platinum still exists.

Jan 1, 2004

By R. Pipeleers

Recent experience has shown that all underground workplaces in the Campine Coalfield in Belgium will require controlled cooling within three years. Considering the socio-economic and legal importance of the climatic problems underground, IREA has undertaken studies in forecasting the climate of future workplaces, planning the necessary cooling equipment and optimizing efficiency in the existing cooling equipment. These studies are being carried out using the climate forecasting program of Bergbau-Forschung. So far, the German model has been obliged to utilize manually measured data from a few workplaces in the Campine. As the model does not fit very well with these measurements, it has been thought necessary to' develop a system of continuous data acquisition and transmission. This system is being tested in the Beringen mine of the N.V. Kempense Steenkollenmijnen. In the first part of this paper the digital tranmission system is described; in the second the sensors used to collect the necessary climatic data are presented, and in the third some results are given.

Jan 1, 1987

By B. Hart, B. K. Gorain, A. Chattopadhyay, S. Dimovc

This paper presents a detailed and systematic approach to metallurgy diagnostics using an integrated novel gold deportment technique for complex copper-gold and refractory gold ore bodies. This uantitative gold deportment for these complex ore bodies is a challenging task due to reasons such as lower grades, high variability of visible and invisible gold content in different sulphides and iron oxide phases, significant presence of disseminated and composite carbonaceous matters along with associations of various copper sulphide phases. Gold mostly occurs as "invisible gold" (sub-microscopic gold) as solid solution or as colloidal-sized particles in different sulphides and other phases. The dominance of invisible gold and presence of highly preg-robbing and finely disseminated carbonaceous matter adversely affects gold recovery in flotation and leach circuits. Studies were initiated on various complex ore deposits and also on samples representing various process streams. Some case studies are presented in this paper to demonstrate the value of a high confidence gold deportment methodology in developing insights for problem diagnostics and to identify opportunities for metallurgical improvements. A systematic and holistic approach involving different fields of expertise is critical for successful development and delivery of solutions for complex ore bodies. Keywords: Integrated gold deportment, complex copper-gold ores, double refractory gold ores, carbonaceous matter, diagnostic metallurgy, preg-robbed surface gold

Jan 1, 2020

By N. F. Mashinini

Optimization of current control systems, proper maintenance and efficient training of personnel are recommendations made to control the amount of dust that underground employees are exposed to on a daily basis in the coal mining industry. This dissertation forms as part of Sasol Mining?s commitment to protect the health and safety of their employees by suppressing and controlling dust at their mines. This study aims to understand the relationship among mining processes, exposure to dust and dust suppression control measures. The research phase of the project was done at the Sasol Mining Secunda complex where underground visits were undertaken to investigate current control systems and also new systems that are being implemented by Sasol Mining. This work was important because it helped determine the sources of dust underground and also to identify the shortcomings of current control systems and to test the efficiencies of the new systems implemented at Sasol Mining. The most important result of the research work was the identification of which underground operators were exposed the most to dust as this assisted in designing a dust suppression system for the areas where these operators worked. The main conclusions of this study are that the current control systems are sufficient for controlling dust and ensuring dust compliance if they are used efficiently and maintained properly.

Jan 1, 2008

By W. K. Brinsden

In August 1965, the late Mr Alan Smith, then Mill Superintendent at Gold Mines of Kalgoorlie (GMK), Australia, asked me to investigate the planting of vegetation on the GMK slimes dams in order to ease the dust problem in urban and industrial areas-a problem that is caused largely by dust from these barren slimes dams. My early sources of information were the comprehensive papers in various issues of the Journal of The South African Institute of Mining and Metallurgy. However, the climate of Johannesburg differs from that of Kalgoorlie. The average Johannesburg rainfall, which falls mostly in summer, is 730 mm, and the average maximum summer temperature is 26°C (top 34°C). The winters are cool, the average maximum being 18°C (low -7°C). Kalgoorlie, on the other hand, receives, on average, 257 mm of sporadic rainfall, has hot dry summers with an average maximum of 35°C (top 45°C), and cool winters with an average maximum of 18°C (low -2°C). My obvious choice was to look at established trees growing on the GMK lease. A number of Athel pines were growing vigorously adjacent to the Oroya mining and geology offices and also on a nearby sand dump. The Athel pine (Tamarix aphylla), which is native to North Africa, Asia, and India, was originally introduced into Australia in 1936 by Mr Essington Lewis, then manager of BHP. His cuttings were planted in Whyalla, where some difficulty had been experienced in finding trees and shrubs that would flourish despite the district's low rainfall. In August 1965, cuttings of approximately 20 cm length and 1 cm diameter were taken from the GMK trees, stripped of leaves, and placed in jars of water in the sun. When the cuttings had sprouted both leaves and roots, they were planted in local soil in tins (about 20 cm high and 10 cm in diameter), and watered daily. In October 1965, when the new shoots were about 8 cm long, the trees were transplanted onto a lower flat section¬approximately 30 m wide, 30 m long, and 2 m high-of the Trafalgar slimes dam. No additional soil or fertilizer was used, and the trees were planted in their tins, the bases of which had been removed (the tin would eventually rust away). A few common varieties of non-prickly cactus and two native salt bush (spp Atriplex) were also planted, but did not survive, probably because of the acidity of the slime. During the summer of 1965/1966, Kalgoorlie's rainfall was 88 per cent above the average, and this probably helped the trees to survive. The moisture content was usually about 2,5 per cent from about 10 cm below the surface, and the pH value of the slime (d80 approximately 75 µm) was about 6. The trees were watered twice a week for the first four months and then left untended. By 1974 they had grown to only about 0,7 m, which indicated that their growth in slime was very slow. Other Athel pines were planted on the wall of the dam, but did not survive beyond 1974, probably because of the steep (about 500) slope and the hardness of the walls, which were initially formed by hand-shovelling of the slime as the height of the dam was raised. Five of the six Athel pines planted in 1965, which probably reached maturity (approximately 5 m in height) in 1981-16 years after being planted-have survived. In the early 1980s, waste rock had to be dumped on the dam, but the management of KMA (now KCGM) took care to ensure that the trees were not buried. Trials are being conducted on other tailings dams so that the performance of cuttings taken from the trees on Trafalgar dam can be compared with that of cuttings taken at various sites in Western Australia. It might also be worth while for an attempt to be made to strike cuttings from Trafalgar dam in pots containing different mixtures of soil and slime.

Jan 1, 1991

The November General Meeting of the Branch was held at the S1. Helena Club on Friday, 15th November, 1968. Mr. J. G. Kirchner (Chairman of the O.F.S. Branch) was in the chair. There were also present: President: Mr R. C. J. Goode. Eighteen Members: Mr A. E. Gilfillan (Council Member), Messrs T. Zadkin, J. N. Saunders, N. A. Honnet, D. D. Waterman, C. R. Netscher, (Committee Members), Messrs G. Thorburn, Z. Lombard, H. V. Henwood, C. J. Isaac, S. L. S. Swart, J. D. McNamara, H. H. Schellhorn, J. W. Wilson, G. C. P. Labuschagne, L. J. Thorne, R. C. Espley-Jones, J. Handley. Seventeen Associate Members: Messrs H. J. Reeders, R. Campbell, P. A. Hoffman, D. E. Couperthwaite, M. D. de Lange, G. J. C. Young, G. W. Futcher, U. Visser, F. H. De Groot, E. Schmid, K. G. Pearce, D. A. Viljoen, H. W. M. Eschenburg, R. Still, W. B. Howe, A. H. Edwards, R. H. Drake. Three Graduates: Messrs T. R. Stromsoe, J. G. Cockburn, T. A. Ward. One Affiliate: Mr O. A. Huss. Twenty-three visitors. Total present: 64. Apologies were reseived from Messrs L. O. W. Leimer, V. C. Barnes and A. Louw. WELCOME TO VISITORS The Chairman declared the meeting open and extended a special welcome to the following: Mr R. C. J. Goode, President of the S.A. Institute of Mining and Metallurgy; Mr A. E. Gilfillan, Member of Council and Mr D. A. Viljoen, all from Johannesburg. Also to Mr J. D. McNamara, the guest speaker for the evening who had made the trip from Oranjekrag. MINUTES OF PREVIOUS GENERAL MEETINGS The minutes of two meetings, viz., the General Meeting held on 26th June, 1968 together with those of the Annual General Meeting held on 14th August, 1968 were taken as read and their adoption moved by Messrs T. Zadkin and D. D. Waterman. MATTERS ARISING FROM THE MINUTES There were no matters arising from the minutes. ADDRESS BY PRESIDENT OF COUNCIL, MR R. C. J. GOODE With regard to the 75th Anniversary of the Institute, the President called upon those present to bear the following two dates in mind, viz.: 21st March, 1969-Banquet at the Wanderers' Club, to which ladies are invited. 24th March, 1969-General Meeting at Kelvin House at 9.30 a.m., the speakers being the President of the Institute, the President of the Chamber of Mines and Dr H. J. van Eck.

By D. Stone, M. Le Roux, Q. P. Campbell, M. Fofana

Float-and-sink analysis is widely used in the coal industry to obtain washability data, yielding important information about beneficiation potential and performance. This method is associated with health and environmental problems, and research into alternative densimetric methods is important. The RhoVol is a new technology developed by De Beers Group Technology South Africa (DebTech) for the image-based generation of densimetric data from ores. The analysis is done on a per-particle basis, within a size range of +3 mm –8 mm. In this paper we compare the established methods used for the float-and-sink analysis of coal with a new method using RhoVol. The aim of the study was to determine the validity of the information obtained from the RhoVol analyser by performing comparative densimetric analysis on three different coal samples. The results showed that the RhoVol method was more rapid, safe, and precise, but tended to consistently underestimate the density of the coal sample, probably due to varying coal porosity.

Oct 3, 2023

By V. I. Ryaboy, V. P. Kretov, I. V. Ryaboy

Attachment of collectors containing thioamide groups to sulfide minerals is interpreted as interaction between NH-acids and sulfides acting as solid bases with the formation of a donor–acceptor reagent–mineral bond. As the acid function of the reagents increases, their sorption optimum is observed to shift to a less alkaline region. The developed concept has enabled us to propose a method for calculating optimal pH values for the sorption of reagents on mineral surfaces depending on the acidity of the reagents and the pH value of the medium. Our estimates correlate well with the experimental data. We studied the spectra of the reagents containing thioamide groups and the spectra of copper salts and their surface compounds on an oxidised copper film, chalcopyrite, and pyrite using the infrared (IR) spectroscopy. Some effective applications are described of reagents containing thioamide groups in the flotation of copper, copper-molybdenum, and gold ores, both separately and in combination with other collectors. It is shown that the flotation performance is maximised by adding two- and three-component collector combinations, including collectors containing thioamide groups. In this case, the increase in the recovery of copper, molybdenum, and gold is up to 2-5% compared to conventional process conditions. A new, high-performing reagent containing a thioamide group is proposed. A commercial pilot batch of the reagent was produced and sent for flotation tests in gold ore applications. Keywords: Thioamide reagents, dialkyldithiophosphate, collectors, flotation, arsenopyrite, chalcopyrite

Jan 1, 2020

By H. El-Faramawy, A. Ahmed, M. Eissa, M. El-Fawakhry, T. Mattar, S. N. Ghali, E. M. Kotb

As a result of the depletion of high-grade manganese reserves, it has become necessary to consider the exploitation of low-grade manganese ores. The main problem of low-grade manganese ore is the low Mn/Fe ratio, which makes it unfit for the production of manganese ferroalloys. In this work, a selective reduction technique was used for smelting low-manganese ore in the presence of coke and fluxing material in an electric submerged arc furnace to obtain a rich manganese slag and low-manganese pig iron. The product slag was blended with medium-manganese ore and smelted in an electric submerged arc furnace, in the presence of coke and the fluxing agent, to produce silicomanganese alloy. The influence of reducing agent ratio, charge basicity, and charge Mn/Si ratio on the smelting process was investigated. The optimum conditions were found to be a coke ratio of, 1.35, Mn/Si ratio of 2.0, and charge basicity of 2.5. The silicomanganese alloy produced under these conditions satisfies the specifications for Si16Mn63 and Si17Mn65. The experimental results were applied on a pilot scale, producing a silicomanganese alloy with a chemical composition close to that of the standard specifications.

Jan 2, 2022

By M. Aatach, St. Gaydardzhiev, M. Kadiyski, E. Visariev, V. Stoilov

Detailed process oriented characterisation on representative samples from plant survey of the slag flotation plant belonging to Aurubis, Bulgaria has been realised in order to evaluate the mineralogical occurrences of Cu, Ni, Mo and Co bearing phases. The slag subjected to flotation consisted in majority of fayalite, magnetite-iron oxides and a glass-like phase. Ni and Mo have been found to be closely associated to magnetite and fayalite. The tailing from the slag flotation has been subjected to sulphation roasting followed by water leaching as a hydrometallurgical means to recover the remaining Cu, Mo, Ni and Co. Based on the various sulphation roasting conditions (acid dosage, duration, temperature) copper, nickel and cobalt were brought to solution to a different extent. Molybdenum was the most difficult to be rendered soluble due to its close association with iron, suspected to form an insoluble compound with it. Sulphation roasting performed at 350ºC has secured the best extraction degree for Cu, Mo and Co, while maximum recovery of Ni has been documented when roasting was done at 150°C. Keywords: Copper slag; characterisation; SEM; roasting; metals leaching, hydrometallurgy 16(2), 153–65.

Jan 1, 2020

By D. F. Malan, D. Ile

This study explores the use of backfill in hard rock bord-and-pillar mines to increase the pillar strength and extraction ratio at depth. The use of backfill will also minimize the requirement for tailings storage on surface and the risk of environmental damage. A literature survey indicated that backfill is extensively used in coal mines, but rarely in hard rock bord-and-pillar mines. To simulate the effect of backfill confinement on pillar strength, an extension of the limit equilibrium model is proposed. Numerical modelling of an actual platinum mine layout is used to illustrate the beneficial effect of backfill on pillar stability at greater depths. The magnitude of confinement exerted by the backfill on the pillar sidewalls is unknown, however, and this needs to be quantified using experimental backfill mining sections equipped with suitable instrumentation.

May 3, 2023

By M. B. C. Brandt

Richter magnitudes for seismic events were calibrated for use as a Local magnitude scale in the West Rand (WR), Far West Rand (FWR), and Klerksdorp–Orkney–Stilfontein–Hartebeesfontein (KOSH) gold mining areas. Richter magnitudes are currently calculated from seismograms recorded by local surface cluster networks using tabulated calibration values for Southern California, published in 1958. The Richter (1958) model is incorrect for distances of less than 30 km and should be applied only to crustal earthquakes in regions with similar attenuation properties to those of Southern California. When compared to the South African National Seismograph Network (SANSN), the cluster networks, on average, overestimate seismic event magnitudes by approximately 0.1 of a magnitude unit. A calibrated Local magnitude scale was derived by means of a multiple regression analysis between the Local magnitudes reported by the SANSN and the largest zero-to-peak trace amplitudes measured on the cluster network horizontal seismograms, after modelling the attenuation of the seismic waves as these progress from the epicentre to the station position. Magnitudes reported by individual stations for the same event show a significant scatter around the average magnitude owing to the near-surface amplifications of the seismic waves at the recordings sites. Average magnitude should be estimated using as many magnitudes of individual stations as possible to ensure an accurate estimate. Larger event magnitudes should be compared with those recorded by the SANSN.

Nov 1, 2021

By M. Bueno, T. Chavez Matus, M. S. Powell, S. Michaux, S. Luukkanen

Comminution tests are an essential element in the design of ore beneficiation plants. Many methods have been developed to assess the breakage characteristics of rocks to generate parameters for modelling. However, most of the existing methods are laborious, expensive and require large samples. Consequently, test work has been traditionally conducted with a few representative reference samples. On the other hand, geometallurgical modelling programs require an extensive amount of test work to allow understanding the variability of ore properties within the deposit and establish spatial geometallurgical domains that show the differential responses to mineral processing. Therefore, comminution tests for geometallurgy need to be more efficient in terms of time, cost and sample size. This paper introduces a new testing device (Geopyörä) which is capable of measuring forces and energy applied to rock particles during the breakage process. The new testing method uses smaller samples and can be up to 50 times faster than other commonly used tests in the industry. This paper presents the concept prototype and the preliminary test work results, which have been benchmarked against some of the industry standard tests, such as the JK Drop Weight Test (JKDWT), the SMC Test® and the Bond ball mill test. Keywords: Geometallurgy, comminution, ore breakage characterization, variability.

Jan 1, 2020

By L. Morgan, M. Le Roux, Q. P. Campbell

Dry coal processing is becoming increasingly favoured as a fine coal beneficiation technique. The decline in suitable good-quality coal, as well as the ongoing decrease in usable process water, makes dry beneficiation of the fine coal fraction even more crucial. Dry fine coal beneficiation is a relatively young process with most of the methods still in the developmental phase. Additionally, many of the dry processing options available are better suited for coarser (+6 mm) and easy-to-beneficiate coal. Air winnowing for fine particles has been established in both agricultural and pharmaceutical industries, which indicates that the method can be used to separate smaller particles on a density basis and therefore, may prove effective in the coal industry as well. A proof of concept study was conducted using both computer-based simulations (which do not form part of this paper) and physical experiments. The initial winnowing unit consisted of a closed box with a horizontal air stream flowing through the top section. Coal particles were injected into the air stream and displaced horizontally across a distance (x), depending on the particle size and density, thus actuating a separation based on these two parameters. For this study particle sizes of 6, 4 and 2 mm were used all with a density ranging from 1200 kg·m-3 to 2000 kg·m-3. The simulation in Star CCM+ confirmed the findings of the mathematic behavioural model and provided a virtual representation of the separation using streamlines and particle tracks. The coal tests prove that size separation can be achieved at an airflow velocity of 21 m·s-1 and the density cut-point can also be predicted by using the prediction matrices constructed as part of this study. The results show efficiency values (EPM) of 0.11 and 0.09 at density cut-points of 1400 kg·m-3 and 1500 kg·m-3 respectively. The data obtained from the study indicates that air winnowing can be used to separate fine coal particles based on both size and density. However, in order to achieve an efficient density separation, a narrow size range is required. With some improvements to the model, simulation, method and design, the separation efficiency can also be improved. The next phase of testing will include the upscaling of the process to a demonstration plant, optimising the separation unit and testing the method on different qualities of coal. Keywords: Dry processing, fine coal, winnowing, simulation, tracers, demonstration plant

Jan 1, 2020

By C. Bester, G. M. Rohde

A major challenge in the mining sector is the responsible management and efficient storage of mine residue. Over recent years numerous tailings dams have experienced unintended spills and failures, with severe consequences for the mining industry, the environment, local communities, and the regional economy. The fourth industrial revolution (4IR) is impacting society due to increased interconnectivity, processing speed, and automated technologies. This paper explores whether 4IR technologies have the potential to mitigate risks associated with tailings dams. Experts in the field of tailings dam operational management were surveyed to determine their view on the risks associated with tailings dams and the potential of 4IR technologies to mitigate these risks. The survey found that a majority of experts believe that certain 4IR technologies have the potential to reduce the risks associated with tailings dam failures.

May 27, 2025