Search Documents

By J. B. Littlefield

The Greenburg-Smith impinger was developed at the Bureau of Mines in cooperation with the United States Public Health Service in 1922 in the course of an investigation of dust-sampling instruments available at that time. Although it is not used extensively outside of the United States, it is now soused in this country to collect samples for the determination of any dustiness, and most of the information correlating degree of dustiness with physiological effect has been obtained by the impinger method. The chief disadvantages in the use of the regular impinger, especially in mines and other places accessible with difficulty, are its bulk, weight, and power requirements. It requires a source either of electricity or of compressed air, which necessitates connections and extension of existing supply lines to each sampling point; the only alternative is the use of a relatively large pump hand-operated with considerable effort.

Jan 1, 1937

By Louis A. Turnbull, JOSEPH J. SHIELDS

The Bell & Zoller Coal & Mining Co. recently completed construction of two slopes at Mine 3 near Zeigler , Ill . The slopes are in the Big Muddy River Valley , and construction was particularly difficult because the strata from the surface to a depth of 70 feet comprise water saturated sandy clay and sand . Many mining companies have similar shaft- and slope - sinking problems , and because these slopes were satisfactorily completed and now are in use the methods followed during construction are described in this information circular . It is believed that other companies with similar problems . will benefit by adopting the methods followed at Mine 3 .

Apr 1, 1949

By James C. Cawley

The Bureau of Mines has empirically determined ignition probability versus current for resistive circuits in an 8.3% methane-air atmosphere. Simple ignition probability, defined as the number of ignitions divided by the total number of sparks, was determined, and the corresponding currents were recorded. The experiment was designed to minimize the probability of not observing an ignition that should occur during a series of tests. For resistive circuits in 8.3% methane-air mixtures, the experimental results indicate that ignition was not achieved below 2,000 rnA at 20 V dc, 350 rnA at 30 V dc, 150 rnA at 40 V dc, and 175 rnA at 50 V dc. The simple probability of ignition corresponding to these currents is esti-mated to be, respectively, 1.0 x 10-6, 1.7 x 10-7, 3.0 x 10-7, and 1.0 x 10-5 The ignition mechanism seems to break down below this point, implying that a threshold current value exists below which spark ignition does not occur.

Jan 1, 1987

By R. V. Ramani, A. S. C. Owili-eger

Mathematical modeling is a scientific exercise with the objective of developing simplified mathematical statements that relate to one another the same way as the processes that are being modeled. The utility value of the model is dependent on the ability of the model to closely approximate prototype behavior. Development of a perfect model, therefore, is an unrealistic objective because of the simpli¬fying assumptions made in building it. However, for a model to be acceptable for application, its operating characteristics or data generated from it should, within reasonable accuracy, duplicate proto¬performance. The validity and accuracy of a model depends on the mathematical constraints presupposed in model formulation. The final model must be tested for mathematical validity and for closeness of representation of the prototype. Mathematical validity, does not, however, imply that the model is accurate and correct but is prerequisite. Model testing and verification for the steady state model are given in Owili-Eger et al (1973). The unsteady state model has been tested for mathematical validity and found to be correct but has not yet been applied to a field condition for lack of data. However, in the application discussed below, the unsteady state model results are compared with pressure curves reported in literature and also with results from the steady state model. Coal seam characteristics and gas reservoir pressure used in this application are extracted from Kissell (1972). These characteristics are for the Pittsburgh seam, Federal No. 2 Mine, Fairview, West Virginia.

Jan 1, 1974

By H. E. Camargo

In an effort to decrease noise-induced hearing loss (NIHL) in coal preparation plant employees, the National Institute for Occupational Safety and Health (NIOSH) is conduct­ing research to identify and control dominant noise sources in vibrating screen (VS) machines. To this end, acoustic measurements of the noise radiated by a dewatering VS were conducted at the Pittsburgh Research Laboratory (PRL) using microphone phased-array technology. These measurements allowed for the identification of the screen as the dominant source in the 250 Hz 1/3-octave band. The sidewalls are the major contributors in the 315 and 400 Hz bands, whereas the eccentric mechanisms and the electric motor are the dominant sources in the 800 and 1,000 Hz bands, respectively.

Jan 1, 2009

By Phillip W. Holland

The U.S. Bureau of Mines has developed a mass spectrometer method for determining helium in the parts-per-million to 10% range to an accuracy of ± 1%. The method employs a mass spectrometer, an inlet system utilizing a chromatographic gas-sampling valve, and an activated coconut charcoal trap cooled with liquid nitrogen. Gravimetrically prepared standards of helium in nitrogen were used to demonstrate the linearity of the method over the concentration range of 10 ppm to 10.66% helium.

Jan 1, 2010

By H. V. Makar

An aluminizing dross which is accumulating as a waste material in substantial quantities was tested for possible use as a steel deoxidizer. This material, consisting mainly of aluminum, silicon, and iron, was used to deoxidize laboratory-scale melts ranging from 7 to 100 pounds. Oxygen analysis showed that the aluminizing dross was effective in reducing oxygen levels in steel. A direct comparison with aluminum wire showed the dross material to be at least as effective. Under similar test conditions with 7-pound melts, 3 grams of aluminum reduced the oxygen concentration from 210 to 175 ppm, while 4 grams of aluminizing dross (equivalent to approximately 2 grams aluminum) reduced the oxygen concentration from 250 to 170 ppm. An additional 4 grams of aluminizing dross produced a final oxygen concentration of 140 ppm.

Jan 1, 1972

By L. H. Adami

This paper reports the results of solution calorimetry conducted to obtain the heats of formation of crystalline FeS04?6.952H20 and FeS04?1.008H20, from. which values were derived for the stoichiometric compounds FeS04?H20 and FeS04?H20. Also included are derived values of the free energies of formation and dehydration. This work was undertaken primarily to fill a need for data for pure, easily obtainable ferrous compounds that are suitable for use as calorimetric intermediates, The ferrous sulfate hydrates meet the essential requirements for this use.

Jan 1, 1963

By Alla D. Mah

Combustion energies of barium and strontium were measured by means of the combustion bomb calorimeter. The heats of formation obtained for the oxides were ?H298.15 = -139,060 ± 700 cal/mole of barium oxide (BaO) and ?H298.15 = -144,440 ± 400 cal/mole of strontium oxide (SrO). Tables containing heats and free energies of formation from 298.15° to 2,000° K were prepared.

Jan 1, 1963

By H. E. Powell

The smelting of brass and bronze generates a dust composed primarily of zinc oxide, with lesser amounts of other metal oxides, such as copper, lead, and tin. The small quantity of this waste generated by individual smelters and the relatively low unit value of the contained metals, suggests the desirability of reclaiming the metals onsite or at some nearby point. The Bureau of Mines has developed a process that fits these requirements. The technique consists of (1) dissolving zinc and copper from the dust with sulfuric acid, (2) recovery of copper by cementation, (3) recovery of zinc as zinc sulfate crystals, and (4) recovery of lead and tin as a salable residue. Alternatively, zinc may be recovered by electrodeposition. Free acid is recycled and no major pollution problems are generated by the process.

Jan 1, 1972

By R. R. Schehl

The Bureau of Mines has developed a quantitative Analysis for pyrite in coal by X-ray diffraction that can be accomplished in little more than 1 hour. To minimize the sample analysis time, data processing has been completely computerized with pertinent output information displayed on a VR12 cathode-ray tube display. Use of this computerized system is not only advantageous during the experimental stages of the pyrite analysis project but would also be essential if the X-ray diffraction procedure is accepted as a standard method of analysis.

Jan 1, 1973

By K. C. Dean

A semiquantitative test for the presence and identification of cesium and rubidium in rocks, clays, and mineral waters has been developed by the Bureau of Mines. The test can be used in the field, as a guide for the prospector, geologist, or mining engineer engaged in location or development [w]ork. It comprises two simple spot tests of a solution prepared from the [m]ineral sample. Phosphomolybdic acid, added to a drop of the test solution, [d]etects cesium, rubidium, and potassium in quantities as low as 60 parts per [m]illion. Silicomolybdic acid, added to a second drop of test solution, enables the operator to distinguish between cesium and/or rubidium and potassium. Test procedures, equipment requirements, and limitations of the method are described in this report. Cesium and rubidium were discovered in 1860 and 1861 by Bunsen and Kirchhoff with a spectroscope. The elements usually occur together, particularly in granite and granitic pegmatites. Rubidium does not occur as an essential constituent of any known mineral, yet it is found as a minor element in so many minerals that rubidium is 16th in abundance in the earth's crust. Cesium, which ranks as the 37th most abundant element, is the principal component of pollucite and a minor element in a wide variety of minerals.

Jan 1, 1960

By N. H. Coates

As part of a joint program of the U.S. Atomic Energy Commission and the Federal Bureau of Mines for using nuclear energy to supply process heat, the Bureau designed and constructed a pilot-scale simulated nuclear reactor system. Although workable components were developed,5 the simulated nuclear reactor could not be operated continuously at its design conditions of 2,500°F. and 250 p.s.i.g. because the refractory materials used for insulation deteriorated. Replacement of these materials with porous carbon permitted sustained operation at design conditions, and a 1,000-hour demonstration run was completed successfully. No serious operating difficulties developed during the test. Leakage of helium after 1,000 hours was only 3 to 4 std. c.f.h. Inspection after the run revealed no damage to any of the components. Including earlier runs during previous research5 the system has been operated about 4,000 hours, of which 1,120 hours have been at 2,500° F. or higher. The helium-recycle compressor performed satisfactorily with no main¬tenance whatever for 2,445 hours, with about 2,000 hours at 900° to 1,000° F.

Jan 1, 1961

By Charles L. Kimbell

The final tables of this chapter, tables 25-50, extend and expand the statistical series on production that was started in the 1963 edition of the Area Reports: International Volume of the Minerals Yearbook and that was subsequently updated and expanded in the 1965 and 1967-90 editions. Continuing the practice started in 1989, a column has been included in each of these tables providing a 5-year average for 1987-91, inclusive. This should provide a clearer picture more rapidly of the role of each major producer over the 5-year period. The listing order of major producers, however, continued to be, as in past years, in descending order of rank in the year of review, 1991. This group of tables now includes each of the crude minerals that ranked from? 1st to 19th in 1983 terms of value of their output (as well as four others of lesser rank). These 23 crude mineral commodities accounted for 93 % of the estimated value of world crude mineral production in 1983. In addition, world output of five key downstream products-aluminum, steel, cement, nitrogen in ammonia, and refined oil-is included because of their significance as products.

Jan 1, 1993

By David Hoadley, Kenneth R. Maser, Ashok B. Boghani, James E. Billar, D. Randolph Berry, Mackenzie Burnett, Robert H. Trent

5. General Escapeway Requirements 5.1 Escape Routes Present escapeway regulations state "Every mine shall have two separate properly maintained escapeways to the surface which are so positioned that damage to one shall not lessen the effectiveness of the other, or a method of refuge shall be provided when only one opening to the surface is possible." "Escape routes shall be a. Inspected at regular intervals and maintained in safe, travellable condition, b. Marked with conspicuous and easily read direction signs that clearly indicate the ways of escape." "Application. "Regular" intervals means at intervals no greater than monthly where conditions are stable and oftener where conditions may change." "Designated escapeways inclined more than 30* from the horizontal shall be equipped with stairways, ladders, cleated walkways, or emergency hoisting facilities." As can be noted in present and proposed regulations there must be two separate properly maintained escapeways. In most operations, the escapeways will consist of one route that is the normal travelway used in day to day operations. The second route is usually a return airway through old work areas. Based on this generally accepted practice, we will designate the two types as primary and secondary.

Jan 1, 1976

By Thomas M. Barczak

Purchasing a new set of longwall shields requires a substantial investment. A poor shield design can lead to economic hardships, safety concerns for the mine workers, and closure of the mine. This paper addresses several key points that should be considered in the procurement process: (1) understanding your goals and the logic in selecting a higher capacity shield, (2) the importance of completing performance testing before production shield fabrication begins, (3) making sure performance testing is properly done, (4) measuring load(stress) development during performance testing, (5) testing a shield to failure, and (6) the value of buying extra shields. In addition, several challenges are proposed for consideration in future shield designs. These include (1) 100,000 life-cycle expectancy, (2) improved hydraulic diagnostic capability, (3) smart load control by optimizing setting pressures, (4) lubricated link joint design concepts, (5) composite material applications to reduce shield weight, (6) incorporating periodic weighting predictive algorithms into the data-processing software, (7) advanced component load measurement on two to three specially instrumented shields to detect loading in the structural components, and (8) constant set leg cylinder design.

Jan 10, 2000

Develop a simple and practical technique to measure in situ rock mass properties for realistic design and stability evaluation of underground structures. Background The Bureau of Mines has developed basic principles and techniques to determine in situ rock mass properties including Poisson's ratio, deformation modulus, and yield and failure strengths. An instrumentation package consisting of three pressure cells is installed in a single drill hole. Cell pressure response data are acquired and used to calculate and determine the rock mass properties. How It Works A test hole of BX size (approximately 5.7 cm) or larger is drilled to the approximate depth of the measuring point. The last portion of the test hole is drilled with precision bits to EX size (approximately 3.8 cm). The instrumentation package, which consists of one 3.8-cm-diameter cylindrical pressure cell (CPC) and two 5.7-cm-diameter cement-capsulated, flat borehole pressure cells (BPC's), is then installed. A complete history of cell response to changing strata loads is acquired on a continuous basis with a chart-type hydraulic pressure recorder. From these cell pressure data, Poisson's ratios, deformation moduli, and yield and failure strengths are calculated and determined.

Jan 1, 1990

By William K. Tolley

The U.S. Bureau of Mines (USBM) is currently investigating the electrochemistry of mineral flotation. A significant need in this area is greater reliability of sensors. The USBM is testing electrolytic methods to clean and condition redox-sensing electrodes to improve the reliability and extend the service life of these instruments in the harsh physical and chemical environment of mineral processing slurries. A novel method for removing scale from fouled electrodes has been developed that includes anodic polarization to 1.2 V versus the Ag/ AgC1 reference potential, followed by brief potentiodynamic conditioning. Laboratory results show that this technique removes calcarious deposits from gold sensing electrodes and returns the electrodes to useful service within approximately 10 min. Mechanical abrasion to remove the scale is thereby avoided.

Jan 1, 2010

By J. B. Gayle

This investigation was conducted by the Federal Bureau of Mines to compare the selectivities of diverse flotation reagents and also of flotation and float-sink methods of separation. Flotation tests, using sodium chloride, an alcohol-type frothing agent, and a kerosine-pine oil mixture as reagents, were made on seven coking-coal samples representing four different beds. The results indicated equivalent selectivities relative to sulfur rejection when entrapment effects were minimized by recleaning the various products. Selectivities relative to ash rejection were also equivalent for some coals; for others, the selectivities of the reagents tended to increase in the order sodium chloride, alcohol-type frother, and kerosine-pine oil. Float-sink tests on these same coals generally gave results indicating better selectivities than those obtained in flotation tests at comparable levels of recovery.

Jan 1, 1960

By M. F. Dunn

A handbook to provide a quick reference guide for selecting and using jet fans in a variety of conditions was prepared. The document is intended for use by front-line supervision, ventilation engineers, and mine planners. Included are discussions of jet fan characteristics, selection and use critieria, and do's and don't's for easier operation, safety, and performance. The handbook is based on research at three underground metal/nonmetal mines having cross-sectional areas of 900 to 2,000 ft2.

Jan 1, 1983