Search Documents

By R. C. Buehl

[Improvements in refractories for high-temperature service have made possible the use of higher temperature in many processes. Consequently, it sometimes is desirable to use gases heated above 1,600° F., and for moderate rates of gas flow, there gases can be heaters best with pebble heaters. Pebble heaters of the stationary-bed type in which the chanber was lined with mullite brick and pebbles of pure alumina served as the heat-exchange medium have been used recently to heat the air blown into an experimental blast furnace4/ These pebble heaters worked well and made it possible to use air temperature up to 2,500° F. at the tuyere of the furnace. Since little has been published on this type of gas heater, a review of the construction on employed and operating data should assist in selecting applications and designing units.]

Jan 1, 1953

By G. W. Grove, H. R. Burdelsky, F. E. Griffith

"INTRODUCTION The work of using a system of air locks in unsealing a mine in Ohio following a fire probably was one of the outstanding jobs of its kind in a medium-thick coal bed.The fire in this mine, thought to have been of electrical origin, was discovered at about 1:30 a.m. on December 11, 1941. Forty-four men were working in the affected section at the time; 5 escaped unassisted, and 37, who had barricaded themselves, were rescued. The bodies of two men, who had succumbed after breathing fumes given off by the fire, were brought part way out of the mine before it became necessary to seal the mine.Direct attempts to extinguish the fire with water were abandoned when hazardous amounts of 'carbon monoxide, methane, and other inflammable gases were detected in return air passing through the main haulageway and escape-way of the mine.The mine was completely sealed on the surface at about 8 p.m. on December 12, 1941, with the two bodies remaining in the mine. Sixteen days after the mine had been sealed, the two bodies were recovered. This was accomplished by air-locking through a partitioned-off stairs compartment of a ventilation shaft. This work was done under adverse barometric and atmospheric conditions.A method for collecting representative air samples from the immediate fire area was used successfully by utilizing a vacuum pump on about 10,000 feet of existing water line that had been broken near the fire area.The immediate fire region was sealed, and confined to a relatively small area; the remainder of the mine was recovered, and operations were resumed February 9, 1942, or 59, days from the time of sealing the mine on the surface. This recovery was made by air-locking the main entries inby from the shaft and No. 2 right-face entries.The distance between air locks averaged about 500 feet, and as each new set of seal stoppings and air locks was completed, the old or outby seals were taken out and the area between was ventilated. In ventilating this area, it was often necessary to use line curtains to direct the air into dead-end places."

Oct 1, 1947

By L. C. IlsLey, Charles M. Means

The descriptive rather than the strictly technical meaning of many of the terms and expressions used in the electrical rules is given in order to assist in their interpге- tation . ALIVE . At a potential measurable with a voltmeter and different from that of the earth or another conductor . (Static charges should be determined with an electrostatic voltmeter . This condition may apply to current - carrying parts , to noncurrent - carrying parts and adjacent material where a failure of insulation has taken place , and to objects having stored or static electricity . ) ALTERNATING CURRENT . A current that changes in direction -- positive or negative-- a certain number of times per second , depending upon the number of poles and speed of the generator . AMMETER. An instrument for measuring current , indicating in amperes . AMPERE . A term applied to denote the rate of current flow . ( Analogous to " gallons per minute " in a hydraulic system . ) APPROVED . Accepted as suitable by a competent committee , board , or organization designated by those adopting the rules . ductors . ARMOR . A steel or equivalent metallic covering for one or more electric con- AUTHORIZED PERSON . Anyone commissioned by the official in charge of the mine or his deputies to carry out certain duties incident to the generation , transformation , and distribution or use of electric energy in the mine , such person being one who is competent within the purpose of the rule in which the term is used .

May 1, 1930

By Richard L. Rains

The Bureau of Mines conducted a mineral investigation of the 29,000-acre Dixie Summit area near Elk City, Idaho, during the summer of 1989. At the Petsite mine a marginally economic, identified resource of 4.9 million tons with an average grade of 0.023 ounces gold per ton was delineated. Possible resources of gold, along with silver, copper, lead, and zinc, occur in at least eight other lode deposits. Placer gold may be recoverable by recreational-sized suction dredges in some stream drainages, Five lode mines in the study area have produced over 5,516 ounces of gold (placer gold production was not recorded), 4,757 troy ounces of sliver, 36,746 pounds of lead, and 3,800 pounds of copper. Current mining claims in or adjacent to the study area total 460 lode and 70 placer claims. There are two patented lode claims within the Dixie Summit study area.

Jan 1, 1991

By John Nagy, Henry G. Dorsett, Murray Jacobson

Laboratory studies show that ignition of a dispersed combustible dust in an open vessel may be prevented by adequate inerting . Factors affecting the inerting requirements are -- dust concentration , spark energy , ignition temperature , composition of the substances used for inerting , fineness of dust and type of combustible . The oxygen concentration of the atmosphere and in some instances the proportion of admixed inert powder and moisture required to prevent ignition are given for 367 dust samples . Variations in inerting requirements with strength of igniting source are discussed .

Jan 1, 1964

By Paris V. Brough

This paper, which describes the practice of milling custom ore, in addition to that produced under company and lease operations in the Tom Reed mines, is one of a series 'being prepared by the Bureau of Mines. ACKNOWLEDGMENT Acknowledgment is made to W. B. Phelps, managing director, and Jack Zwinge, superintendent, far permission to publish, a-ad to G. E. Jarpe, the present mill superintendent, for his assistance in preparing the paper. LOCATION The mill is in Oatman, adjacent to the Benjamin Harrison shaft of the Tom Reed Gold Mines Co., in the foothills on the western slope of the Black Mountains, western Mohave County. The railroad shipping point is Kingman, Ariz., 25 miles northeast of Oatman. Paved highway U. S. 66 passes by the mill. The altitude is approximately 2,700 feet.

Jan 1, 1937

By Terry S. Cory

This report covers antenna design, analysis, and development work suited for use with a wireless radio communication system operating at medium frequency. The work includes the test and evaluation of prototype vehicular antennas developed during the program.

Jan 12, 1978

By R. E. Mussler

As part of an overall goal to develop technology that can maintain an adequate supply of minerals to meet national economic and strategic needs, the Bureau of Mines is evaluating a method for selectively extracting nickel and cobalt from low-grade domestic laterites. The method involves electrowinning to recover the metals in pure form; therefore, preliminary laboratory-scale electrowinning tests were conducted in both a nondiaphragm and a diaphragm cell to determine the effect of variables on energy efficiency under controlled conditions. Electrolytes were generally reagent-grade sulfate solutions that were prepared to simulate electrolyte that could be obtained by stripping nickel-and cobalt-rich solvent extraction reagents. Limited tests were conducted with electrolyte generated from laterite leach solutions. Electrical energy consumption in a nondiaphragm cell was 2.06 kwhr/lb Ni with the cell operated at 50° C, a cell feed of 90 g/l Ni, a pH of 3.5, an extraction of 3.2 g/l, and a cathode current density of 20 amp/ft2. The energy requirement decreased with increasing concentration and temperature, and increased with increasing. extraction and current density. At 50° C, energy consumption in the nondiaphragm cell was 21 pct greater than in the diaphragm cell, but it was only 5 pet greater at 65° C. For this reason and because of overall cost considerations, operation at 65° C with the nondiaphragm cell was preferred. Smooth sheets of cobalt were obtained by electrowinning in a nondiaphragm cell at selected temperatures from 50° to 85° C and with cobalt concentrations from 55 to 87 g/l. The energy consumption (1.48 kwhr/lb) was 22 pet lower with a cobalt concentration of 75 g/l and a cell temperature of 65° C than with a cobalt concentration of 55 g/l and a cell temperature of 50° C.

Jan 1, 1981

By F. L. Wideman

This report describes the sinking of No. 3 shaft at the Westvaco mine. It is one of a series of publications of the Bureau of Mines on mining methods and practices in the United States. The Westvaco mine is in Sweetwater County, Wyo., approximately 23 miles northwest of the town of Green River (fig. I), There are no permanent habitations in the vicinity of the mine, and employees live in Green River or Rock Springs, Wyo., 14 miles us t of Green River. The mine plant is on a windswept, treeless plain, from which low buttes and flat-topped ridges rise. The altitude at the collar of No. 3 shaft is 6,351 feet. The climate is arid, with temperatures as low as 40° below zero in the winter. Blacks Fork, a tributary of the Green River and a perennial stream, flows near the mine.

Jan 1, 1959

By Ludwig Schmidt

[The use of vapor-tight tanks has proved so effective in reducing the evaporation losses of petroleum that today practically all operators are using this typo of equipment. It has boon shown, however, that vapor-tight tanks should be supplemented with additional measures which will further reduce evaporation. Probably the most effective use of the supplemental measures are found on the small producing leases where the breathing losses from vapor-tight stock tanks materially affect the volume and gravity of the stored oil. The breathing loss from a vapor-tight stock tank that is filled and emptied daily is a negligible quantity. Also, the filling loss, which on the average varies between 0.1 and 0.2 per cent, usually is not of a sufficient quantity to affect materially the value of the crude. However, the combined breathing and filling losses from a vapor-tight tank requiring several days to fill are of sufficient importance to warrant the use of measures in addition to the vapor-tight tanks. The breathing losses are caused by atmospheric variations. Probably the greatest are the changes in atmospheric temperature which cause changes in temperature of the vapors in the tank. During the day, as the temperature increases, the gasoline-saturated vapors in the tank expand and are forced out into the atmosphere. At night the vapors are cooled and contract, drawing into the tank fresh air, which becomes saturated with gasoline vapor and is forced out of the tank during the following day. In Addition to the maximum and minimums temperature variations there are many smaller variations throughout a twenty-four period caused by showers, clouds, winds, and other atmospheric conditions which likewise cause the tank to breathe. The two mist common measures used by lease operators for reducing breathing losses in vapor-tight tanks are, first, operating; lease tanks under pressure, and second, the use of light colored paints anti tank houses. In this report these two methods are discussed together with their adaptability to lease operation. Results of experimental observations are given which show the reduction of evaporation looses where these supplemental measures have been used.]

Jan 1, 1927

By J. Weinberg

This Bureau of Mines report presents data on the changes in the use of steel in motor vehicles over the past 35 yr. Sources of supply of steel for the automotive sector have shifted from almost all domestic in the 1950's to about 50% domestic and 50% foreign in the 1980's. Downsizing, design changes, and substitution of lighter weight materials to achieve energy efficiency also contributed to the market loss of the domestic steel industry. Although plastics and aluminum have displaced some steel in motor vehicles over the years, heavy low-carbon steel is now being replaced most rapidly by lightweight high-strength steel. If the percent of domestic steel used in motor vehicles had not declined since 1950, domestic industry would have supplied 9.3 million more short tons of steel than it supplied in 1985. Downsizing and design changes accounted for 43% of the loss; steel imports, 32%; and substitution of plastics and aluminum, 25%. In 1985, the total value of market share lost by U.S. steel producers was $5.1 billion, of which $1.6 billion was lost to foreign steel producers and automobile manufacturers. Through aggressive marketing and increased efficiency, however, the domestic steel industry may be able to recapture some lost markets, as applications for high-strength steels expand, and as foreign-owned automotive plants in the United States provide fresh sales opportunities.

Jan 1, 1988

By Cecil E. Lester

Since the advent of coal mining, the minimal lighting in the under¬ground working place has been an obstacle to the safe and efficient performance of the miner's many tasks. Compounding this problem is the fact that the machines being operated in the working place are so large that the vertical and horizontal clearances around the machinery are severely limited. Consequently, in these poorly lighted and congested working places, the machine operator is unable to utilize his peripheral vision. He cannot see hazards as they develop and, too often, cannot react in time to avoid serious injury or death to himself or his fellow miners. The greatest hazard to miners inby the last open crosscut is from falls of roof which are often preceded by warning signs such as falling rock fragments, roof supports taking weight, or a sudden reduction in the height of the working place. These warning signs often go undectected because the machine operator's attention is focused on the small circle of light emitted from his cap lamp. Congress recognized the illumination deficiencies, and, in the Federal Coal Mine Health and Safety Act of 1969, charged the Secretary of the Interior with the authority and responsibility for development and promulgation of minimum standards for illuminating working places in coal mines. These standards have been developed and, as stated in the April 1, 1976 Notice, Federal Register, Volume 41, No. 64, will be promulgated on October 1, 1976, as mandatory regulations under Section 75.1719, Title 30, Code of Federal Regulations. The regulations require that the designated surfaces within the miner's normal field of vision be illuminated to 0.06 foot-lamberts while self¬propelled mining equipment is being operated in the working places. The term "working place" is defined in the Act as "the area of a coal mine inby the last open crosscut".

Jan 1, 1976

By Kathleen Madland Kowalski

In recent years the issue of human stress response in emergency workers has begun to receive attention. This paper presents a rationale for considering human stress as a significant factor in the management of emergencies. It discusses the concept of stress, Critical Incident Stress in emergency responders, and introduces the Critical Incident Stress Debriefing (CISD) process. It is suggested that, in a disaster, the CISD process can improve the effectiveness of response teams on site, their turnaround time on site, and post disaster time off the job. This paper, prepared by a US Bureau of Mines research psychologist, offers some ideas to the mining industry in general, mine rescue trainers, and more universally, to those responsible for developing emergency management plans.

By L. E. Geyer

"The following list gives the title and author of various publications of the Ceramic Experiment Station, Columbus. Ohio, of the Bureau of mines, together with other ceramic publications of the bureau, which have been published in technical journals and by cooperating agencies. The list also includes the publications on ceramics which have been issued as bulletins, technical papers, or mimeograph Report of Investigations of the bureau.Papers Published in the Technical Press.The Effect of some Electrolytes on the Properties of Clays. Schurecht, H.G. Jour. Am. Cer. Soc., Vol. 1, #3, March, 1918.A Pycnometer Operated as a Volumeter. Schurecht, H.G. Jour. Am. Cer. Soc.,Vol. 1, #8, August, 1918.The Properties of some Ohio and Pennsylvania Stoneware Clays. Schurecht,H.G. Jour. Am. Cer. Soc., Vol. 1, #4, April, 1918.The Fusibility of Graphite Ash and its Influence on the Refractoriness of Bond Clay. Booze, M.C. Jour. Am. Cer. Soc., Vol. 2, #1. Jan., 1919.Behavior under Brass Foundry practice of Crucibles containing Ceylon, Canadian and Alabama Graphites. Stull, R.T. Jour. Am. Cer. Soc., Vol. 2, #3. March, 1919."

Oct 1, 1924

By V. E. Homme

This report describes methods of using sodium for reducing titanic chloride, developed as part of Bureau of Mines activities at Boulder City, Nev., to improve the extractive metallurgy of titanium. Theoretical indications pertaining to the major chemical reactions and possible side reactions of the process are compared with experimental observations. Low-temperature reduction equipment is described, in which titanic chloride was reduced with sodium at temperatures between 97.5° C., the melting point of sodium, and 200° C. Techniques employed in making reductions in ball-mill and high-surface sodium reactors are given.

Jan 1, 1958

By W. P. Stroud

In this U.S. Bureau of Mines report, the conditions required for the direct reconstruction of a tomogram from observed line integrals are examined. Because of the limited access to the working faces in coal mines, the special case of access to only two opposite faces is emphasized. Classical matrix methods were used for small dimensional (2 by 2, 3 by 3, and 4 by 4) applications to determine the limitations and the requirements for a solution. The results for large (n by n) grids were then inferred and generalized from those of the smaller grids and matrices. Limited access tomography is found to be appropriate for in-seam hazard detection from seismic and microwave data, but it is shown that additional data must be added to obtain a direct solution.

Jan 1, 2010

By Richard H. Spencer

Since the passage of the Coal Mine Health and Safety Act of 1969, the Bureau of Mines has made many advances in mine communications. These efforts have resulted in the following developments and demonstrations: Surface-to-surface electromagnetic transmission of baseband voice signals through overburdens as deep as 600 feet. This transmission was achieved with equipment from the Interim Mine Rescue and Survival System Program, and demonstrated that baseband voice communications could be obtained through these overburdens in the absence of mine-generated noise; that is, when the mine power system was shut off, However, during mine operational conditions, the mine-generated noise proved to be so large that effective baseband voice communications to the desired depths could not be effected.

Jan 1, 1975

By A. V. Hooker, E. J. Coggeshall

"The Bureau of Mines for some time advocated the firing of all blasts in coal mines as single shots, and this method of firing is the general practice in American bituminous-coal mines. All single shots can be fired with permissible single-shot units so designed that they will not ignite mixtures of methane and air.If several shots in a face are fired singly it is necessary to return the face after each shot. In some mines having steeply pitching coal seams, this may be dangerous or even impossible, under these conditions shots are usually fired simultaneously.Several shots cannot be fixed simultaneously with permissible single-shot blasting units, and safe types of multiple shots blasters are not readily available. This means that the firing of multiple shots in gassy mines is usually accompanied by the possibility of gas ignition as the blast occurs.Tests have been made at the Pittsburgh Experiment Station to determine the possibility of developing safe types of multiple-shot units suitable for such use, or of applying other type safely in gassy sections of mines where firing shots singly is impracticable.The tests may be divided into the following four groups:1. Tests to demonstrate hazard in the use of existing types of multiple-shot units of the portable generator type.2. Tests to show the electrical characteristics of multiple-shot generator units relative to the possibility of preventing igniting sparks and of modifying the design and application of such units in furthering safety."

Mar 1, 1935

By Phil Patton, Bill M. Stewart, Curtis Clark

Handling materials in underground mines continues to be a major safety problem. To help reduce materials-handling injuries, the National Institute for Occupational Safety and Health (NIOSH) at the Spokane Research Laboratory is developing, modifying, and testing equipment to replace the necessity of doing lifting tasks manually. To reduce single-event lift injuries, equipment having mechanical automatic weight sensing and balancing control was investigated. The Coleman manipulator was selected for testing. Modifications to the Coleman manipulator to make it more suitable for underground mine use included mobilization, self-containment, all-purpose gripper attachment, and support jacks. To reduce or eliminate the need to clean off manually the materials that commonly plug grizzly openings (timbers, wire mesh, roof bolts, and other debris), a track-guided pincher arm device was developed. The TGPA attaches to an impact hammer head, and the pincher arms are controlled by the operator of the hammer. Oversized rock can be broken with the pincher arms in the up position; the arms can then be lowered to grab and remove debris. Sweeping action to remove cohesive fines bridging grizzly openings is also greatly improved. This device is especially useful in recessed grizzlies. An industrial gun was tested to evaluate its effectiveness in breaking oversized rock. Boulders up to 76 cm in diameter were successfully broken to minus-33 cm. Although methods to control fly rock need to be developed, an industrial gun may be a safe and inexpensive alternative to breaking oversized rock in certain underground mining situations.

By D. S. Colby

The productive capacity of natural gasoline and cycling plants in the United States or. January 1, 1954, was 926 thousand barrels per day, according to the Bureau of Mines biennial survey. This represented an increase of 114 thousand barrels per day during the 2-year period since the last survey. In the previous 2-year period, capacity had increased 164 thousand barrels per day. The total number of plants increased from 521 on January 1, 1952, to 535 on January 1, 1954. The number of operating plants increased from 506 to 521. The major increases in capacity took place in Texas, Illinois, Oklahoma, Louisiana, and New Mexico, with the absorption-type plant continuing to account for most of the new construction. In 1954, however, 6 plants reported using a refrigeration process whereas only 1 plant reported this in 1952. The number of operating compression-type plants continued to decline and combination plants showed a decline this year because a number of these plants were reclassified as absorption-type.

Jan 1, 1954