Search Documents

By E. A. Ziemba

The modified in-situ process is one of the methods being considered for extracting oil from oil shale. One of the questions to be answered for this approach is the environmental consequence of underground retort abandonment. This report outlines a study which addresses the question in terms of a grouting solution. It covers the development of a spent shale ash based grout which will fulfill the environmental requirements in terms of strength, stability, and impermeability. In addition, it will allow the reinjection of up to 50 percent of material mined and surface retorted as part of this process.

Jan 1, 1982

By S. D. Cramer

Corrosion research is being conducted by the Federal Bureau of Mines to determine suitable construction materials for geothermal resource recovery plants. As part of this research, the corrosion resistance of 31 iron-nickel-, aluminum-, copper-, titanium-, and molybdenum-base alloys was characterized and evaluated in laboratory corrosion studies in low-and high-salinity geobrines representative of those found in the Imperial Valley, Calif. General, crevice, pitting, weld, and stress corrosion were measured at 105° and 232° C in deaerated brines and brines containing dissolved 02, C02, and CH4 General corrosion rates in deaerated brines at 105° and 232° C were usually below 5 mpy for the alloys tested except carbon steel, the low-alloy steels, Monel 400, 70-30 cupronickel, and the aluminum-base alloys. Dissolving carbon dioxide and methane in the brines at 2320 did not markedly alter these results. However, the introduction of oxygen, which can enter the brine during process operations, seriously degraded the corrosion resistance of many alloys by increasing the incidence of stress corrosion cracking, crevice corrosion and, except for the titanium-base alloys, pitting. In deaerated brine at 2320 C, the general corrosion rates for carbon steel and the low-alloy steels were relatively unaffected by pH in the range of 6.1 to 3.0. However, general corrosion rates increased sharply below pH 3.0. In deaerated brine at 232° C, welds in several iron-, nickel-, and titanium-base alloys corroded at rates comparable to the general corrosion rates of the alloys, but the addition of oxygen to the brine increased corrosion rates for welds in Inconel 625 and E-Brite 26-1. Alloys exhibiting good corrosion resistance in the deaerated Salton Sea KGRA-type brine at 232° C were E-Brite 26-1, Inconel 625, Hastelloy S, Hastelloy G, Hastelloy C-276, TiCode-12, Ti-0.2Pd, Ti-2Ni, Ti-1.7W, and TZM. The alloys most resistant to corrosion in oxygenated Salton Sea KGRA-type brine at 232° C were the titanium-base alloys. These alloys appear the most suitable for use in the construction of geothermal resource recovery plants. Carbon steel and the low-alloy steels are unsatisfactory for high-temperature, high-salinity brines and alternative low-cost materials with improved corrosion resistance should be sought.

Jan 1, 1980

By Sabri Ergun

NEW theoretical data are presented for the intensity of X-rays diffracted from randomly oriented aromatic and alicyclic molecules and diamondlike structures such as are found in coals, cokes, and carbonaceous materials. Data have been computed using the Debye interference function. Computations for the smaller molecules have been made with the Univac 1204 computer: those for large structures, with either the IBM 704 or Bendix G-20 computer. A brief theoretical introduction of the Dobye interference function is given, and an outline is made of the treatment of experimental data so that the experimental interference function can be obtained.

Jan 1, 1965

By E. P. Youngman

This paper presents one of a series of digests of foreign mining legis- ation and court decisions that is being prepared in advance of a generel report elative to the rights of American citizens to explore for minerals and to own nd operate mines in various foreign countries. This interpretation of the laws of Demark and her possessions, has been prepared entirely from answers made by Ernest L. Ives, American charge d'effaires, Copenhagen, to a questionnaire ini- isted by the United States Bureau of Mines and transmitted through the courtesy of the Department of State.

Jun 1, 1932

By W. D. Walker

The trend toward encouragement of worker participation in accident prevention in the coal mines of the United States is not new; however, it has been given added impetus in recent years and is now definitely progressing. It has been found by experience that, although there are many approaches to a mine-safety program that will include the workers themselves as well as their supervisors, no one way is suitable under all circumstances. It requires the concerted efforts of many agencies working along parallel lines toward a common goal. The following seven principal agencies, using somewhat different methods, are listed to illustrate how this problem is approached throughout the coal-mining industry 1. Federal Bureau of Mines. 2. State mining departments (in individual States where coal is produced). 3. Programs conducted by individual mine operators. 4. Programs conducted by mine workers' organizations (unions). 5. Institutes, societies, and other educational organizations. 6. Coal operators' associations (regional and national). 7. Universities, college, and high schools. Each of the seven approaches to safety are discussed briefly, and their methods end contributions, such as publications and other activities, are listed.

Jan 1, 1953

6784. Barnes, V. L., and Romberg, Frederick. Gravity and Magnetic Observations on Iron Mountain Magnetite Deposit, Llano County, Tex. Geophysics, Menasha, Wis., vol. 8, No. 1, 1943, pp. 32-45. An outcrop of magnetite in the Central Mineral region of Texas is explored experimentally with a dip needle and a gravity meter. Two anomalies are observed, one due to the outcropping body and one probably due to a previously unknown body close to the outcrop. The possible attitudes of the bodies are discussed, and their masses and probable dimensions are computed from the gravitational observations. - Author's abstract.

Jan 1, 1943

By C. J. H. Brest van Kempen

The objective of this contract was to provide thrust and torque control and visual output torque readout systems to an existing mine roof bolting machine and to test the consistency of torques obtained under actual field conditions. A Lee Norse TD1 roof bolter was modified by adding a simple torque sensing device to the drill rotation mechanism and a pneumatic logic control circuit that measures torque and controls the hydraulic circuit to the rotation motor. The modification controls and indicates the final installation torque of mine roof bolts. A total of over 5,000 mechanical roof bolts were installed in an operating coal mine. The installed torque of these bolts were within an error band (standard deviation) of 8%.

Jan 1, 1978

By Charles M. Keenan

THIS PUELICATION lists and provides brief accounts of the major disasters not classified as explosions of gas or dust that have occurred in the cod mines of the United States from the earliest times to the present. Together with an earlier publication of the Bureau2 it provides information on all the known major coal-he disasters (disasters causing five or more deaths) in this Nation's history. Sources of each account are given individually. In each account the actual words of the original publication are used unchanged, but sentences or paragraphs referring to details that are not significant have been omitted. In those few cases where conflicting data were reported in different publications the selected version is the one that appears most logical and which in general is in agreement with most of the other accounts.

Jan 1, 1963

By Daniel E. Sullivan

This Bureau of Mines publication examines the potential impact on minerals of the tariff and nontariff agreements that resulted from the Tokyo Round of the Multilateral Trade Negotiations, which were conducted under the auspices of the General Agreement on Tariffs and Trade. These agreements will affect minerals by reducing tariff levels and by changing rules by which they are traded internationally.

Jan 1, 1981

By Francis C. Lincoln

"INTRODUCTION As part of a general investigation of the zinc-producing area of southwestern Wisconsin, the Bureau of Mines undertook a limited amount of exploratory drilling in the immediate vicinity of the New Dale Rundell mine, in the Mifflin District of Iowa County, Wisc.The work was carried out during the early part of 1945, at a time when all effort was being directed toward increasing production of metals important to the Nation's war program. Bureau of Mines engineers decided to conduct exploration at the New Dale Rundell mine after a preliminary study of available data showed a reasonable possibility of indicating an important deposit. Before the Bureau of Mines investigation, 50 holes had been drilled in the vicinity. Of this number, 18 encountered ore of minable grade. Subsequently the mine was developed and operated for a brief period; however, work was stopped before all of the ore disclosed by drilling had been mined. There appeared to be a correlation between the ore shown by the drilling in the New Dale Rundell mine and another disclosure some 1,500 feet to the northwest. The Bureau of Mines exploration was pinned to explore this possible correlation. Of the 7 holes drilled by the Bureau of Mines, 3 disclosed minable ore beyond the limits of previous drilling."

Aug 1, 1946

Exposure to airborne respirable crystalline silica dust can lead to silicosis, a debilitating lung disease. On surface coal mining and construction sites, blast hole drills are notorious sources of airborne respirable dust that may contain significant amounts of silica. The drill operator and drill helper usually receive the greatest silica exposure compared with other occupations. As a result, many drilling operations have been, and still are, on more stringent dust standards. Drilling through various rock formations naturally presents a strong potential for silica dust generation for several reasons. First, drilling is a pulverizing process that generates large amounts of very small dust particles. Second, the bailing air used to flush cuttings from the hole leaves the hole at a very high velocity and can be difficult to contain. Third, many fixed shrouds used to enclose the area beneath the drill deck have a significant amount of leakage due to 1) gaps between the shroud and ground created by raising/leveling the drill, 2) gaps in the corner seams, and 3) tom deck shrouds. CONTROLS A dry dust collection system is typically connected to the drill deck to collect dust as the bailing airflow transports the cuttings (and significant amounts of airborne respirable dust) out of the drill hole. Deck shrouds are installed in an attempt to enclose the volume around the drill steel and prevent dust escaping. However, most deck shrouds are rectangular and constructed of four separate pieces of rubber belting attached to the deck. Because of this design, there is usually a significant amount of dust escaping from the open seams as well as the open area between the shroud and the ground. This dust can be a significant source of silica exposure to drill operators as well as other personnel downwind of the drill.

By Leonard Obert

THE CRACKING AND POPPING of rock, often heard by men working underground, for years has been interpreted as a warning of danger and unstable ground. However, not until 1939 was it discovered that rock under stress generates subaudible and sometimes audible seismic disturbances (referred to as "micro-seismims" 4), which can be detected with the use of a suitable seismic apparatus. Since that date laboratory and field investigations have been in progress to ascertain to what extent this phenomenon can be utilized to detect, localize, and determine the magnitude of areas of instability in and around mine openings and to predict if and when failure will occur. These investigations have included a determination of the types of problems to which the method is applicable and the effect of rock type, geological defects, such as joints, fractures, faults, and other uncontrollable factors, on the reliability of results. Six reports have been prepared covering the investigations conducted between 1940 and 1952 (4-9). 5 These reports describe some of the characteristics of micro-seismims, as determined from both laboratory and field tests; the equipment used to pick up and record micro-seismims; the general test procedure and method of analyzing results; and applications of the method to specific mining problems.

Jan 1, 1957

By G. Stecklein

This report summarizes the results of research into the areas of the fragmentation and entrainment of Airborne Respirable Dust (ARD). The objectives of this program were four-fold: first, to review the present state of knowledge regarding ARD; second, to expand this state of knowledge through the identification of hypothetical microscopic mechanisms by which the coal is fragmented and the dust becomes entrained; third, to specify the informational requirements to verify or nullify these hypotheses; and fourth, to relate experimental techniques that will produce that required information. Additionally, insights are provided regarding potential methods of extraction and/or treatment which may reduce the concentration of ARD.

Jan 1, 1982

By Benjamin W. Haynes

This Bureau of Mines publication comprises a compilation of the state of the science in Pacific Ocean manganese nodule mineralogy and elermental composition. The report is divided into three sections: morphology, mineralogy and elemental composition. The nodule morphology section defines what is considered a nodule for the study, and details the external characteristics and internal structure. Nodule mineralogy is discussed in three sections: manganese minerals, iron oxide minerals, and accessory minerals. The major manganese minerals discussed are todorokite, birnessite, and vernadite. The iron oxide minerals are less well known and include feroxyhyte, goethite, and lepidocrocite. Accessory minerals present include quartz, clays, and other silicates and nonsilicates. A discussion on moisture content is also included. The elemental composition section presents data on 74 elements occurring as cations or anions. Summary data, histograms, and interelement correlation coefficients are presented. The elements are grouped as follows: major and minor elements of potential economic interest (8), other major and minor elements (9), elements of environmental interest (8), rare-earth elements (15), precious-metal-group elements (6), radioactive elements (3), other trace elements (17), and anion-forming elements (8). Cross sectional determinations of Ni, Cu, Zn, Co, Pb, Fe, Ce, and Ba are given for a single nodule to show the general tendency of different growth patterns within a nodule because of different element associations and composition.

Jan 1, 1982

By H. W. C. Prommel

The increase in the price of gold in 1933 was the cause of starting many activities in gold prospecting and mining; it led to investigations of many of the so-called desert placers in the Southwest, which heretofore had not been deemed of commercial importance. Among these, attention was called to some of the gravel beds in the vicinity of the Randsburg-Atolia mining districts of Kern and San Bernardino Counties, Calif., in which gold and scheelite, (calcium tungstate, CaW04) were said to be present. Following a partial sampling and testing of the gravel, large-scale operations were begun in 1935. During the same year more detailed sampling and testing of the gravel beds were done by the author. During 147 days, 1,239 test holes 28 inches in diameter were drilled; their total depth amounted to 16,705 feet. These test holes furnished 2,495 samples of an average volume of 1.0583 cubic yards bank run each; all of the material was run through a sample mill constructed on the property. Original and rather unusual sampling and testing methods had to be used; milling and mining methods for large-scale operations also offered difficulties. The primary purpose of this drilling and sampling campaign was to determine, over a large area, the amounts of gold and scheelite recovered by placer methods such as were already in use on the property. This paper describes sampling and testing methods employed by the author during the 1935 drilling campaign. LOCATION The gold and scheelite placer deposit is in the Atolia tungsten mining district about one-half mile west of the small mining town of Atolia and about 5 miles south of Randsburg in the Randsburg gold-mining district. The deposit lies near the foot of the Rand Hills, in the Mojave desert. The territory is served by hard-surfaced roads from the north and south; Los Angeles is 150 miles to the southwest. A branch of the Southern Pacific Railroad passes within 5 miles of Randsburg.

Jan 1, 1937

By William J. Campbell

Evaluation by the Bureau of Mines of published expansion values for magnesium oxide shows significant variation in values, which may be attributed to sample variables, experimental errors, or systematic differences between measuring techniques. To eliminate the sample variable in measuring expansion, thermal expansion characteristics of a high-purity polycrystalline magnesium oxide were determined by 21 cooperating laboratories using one or more of the following techniques; X-ray camera, X-ray diffractometer, dilatometer, interferometer, and telemicroscope. All expansion values were corrected by the author to a single reference temperature of 25° C. Linear expansion was expressed as a power series in the form of the following equation. Expansion (percent) = [[ A + B (?t) + C (?t)2] ?t 104] The constants, A, B, and C, were determined by least square techniques for X-ray camera, X-ray diffractometer, and dilatometer data separately, and for combined data of all five techniques. Expansion values are tabulated from 26° C. to 1,400° C. in 2° C. intervals using constants derived from X-ray camera data. Below approximately 500° C., expansion values obtained by dilatometric and interferometric methods are significantly lower than those by X-ray methods; above 500° C., this bias decreases rapidly. Comparison of results within methods showed the least variance for X-ray camera results; dilatometer and X-ray diffractometer results have about the same variance. The average deviations, in percent, between observed and calculated expansion values among methods were approximately 10 percent from 100°C. to 300°C., 5 percent from 300°C. to 500°C., and 2 percent from 500°C. to 1,400°C. Maximum deviations were approximately twice as large in most instances.

Jan 1, 1962

By M. C. Malamphy

A general description of the activities and results of bauxite investigation by the Bureau of Mines at its bauxite project in Saline and Pulaski Counties, Ark., has been given in Report of Investigations 4251. The factual data obtained during the project are reported in a series of Reports of Investigation beginning with No. 4251, of which this is the ninth. The data are accompanied by maps showing the location of holes drilled and the deposits developed. Each area upon which work was done is reported by half townships. Each bauxite deposit investigated was assigned a name and a number for ready reference and identification, and its location and name are shown on the appropriate half-township map. The description of each half township is followed by a description of each deposit developed in that half township map. The 14 half-township maps and 77 detail maps of the bauxite deposits in this series of reports give the locations and numbers of all the holes drilled on the project except the deep holes drilled to test the geophysical anomalies. The locations of those holes show on figure 13 in volume 1. The descriptions of the deposits developed are followed by complete detailed logs of the drill holes. Many of the widely spaced exploratory holes did not discover bauxite of minable thickness and grade. The pertinent information obtained from the widely spaced exploratory drill holes has been summarized and tabulated, and a table for each half township is given with the discussion covering that area.

Jan 1, 1948

By Albert L. Toenges

ALMOST all of the coal used for metallurgical purposes west of the Continental Divide is ruined from the Lower Sunnyside bed in Carbon County, Utah. Coke produced from Lower Sunnyside coal and used in western steel plants is weaker structurally than coke used elsewhere in this country. For this reason, western coal operators and steel manufacturers are anxious to develop new areas of coking coal of better quality than the coal produced from the Sunnyside bed. Early in the war, the Bureau of Mines undertook an intensive investigation of western coals to (a) develop additional reserves of coking coal to supplement proved reserves in the Sunnyside bed and (b) develop, if possible, reserves of coal with coking qualities superior to Lower Sunnyside coal. Results of investigations in the Kemmerer district, Wyoming,9 and in the Minnesota Creek area, Gunnison County, Colo.,10 have been published.

Jan 1, 1952

By S. J. Aresco

The Bureau of Mines has been active in promoting the purchase of coal for Government use under specifications that define the requirements in terms of heating value of the coal, expressed in British thermal units, and the composition as shown by proximate analyses. To these, when required, are added the ash-softening temperature, the free-swelling index, and the Hardgrove grindability index. Under most of these specification contracts the bidders guarantee the quality of the coal, and that guaranteed by the successful bidder becomes the standard of his contract. The deliveries are sampled in accordance with instructions4/ issued by the Bureau of Mines; the samples are analyzed in the Bureau laboratory to determine whether the coal is of the quality guaranteed by the contractor and, if it is not, a price adjustment is made. Analyses of the delivered coal and tipple samples (samples collected at mine tipples as coal is being loaded into railroad cars or trucks) provide valuable data for use in evaluating future bids. In addition, the continuous .sampling of coal as delivered is a check on the practical results obtained in burning the coal.

Jan 1, 1958

By J. A. Ruppert

The Bureau of Mines investigated methods of refining iron-contaminated zinc to marketable quality and developed a laboratory-scale process in which aluminum, added as a refining agent, reacted with the iron, forming solid Fe2Al which floated to the surface of the melt. Solids were separated by both filtration and centrifugation, using a unique type of "dipping" centrifuge devised during the work. Typical zinc recovery was 95 percent, and iron content of the metal was lowered from 0.37 to 0.02 percent.

Jan 1, 1967